Big Ass Fans Haiku I Series Guide d'installation

INSTALLATION GUIDE

GUÍA DE INSTALACIÓN

GUIDE D’INSTALLATION

READ AND SAVE THESE INSTRUCTIONS

Topic Page

Technical Speciﬁcations 3

Tools Needed 3

Parts and Hardware

Low Proﬁle Mount

4

Standard Mount

5

Universal Mount

6

Prepare the Fan Site 7

Install Your Fan

Airfoils

8

Lower Cover and Trim

10

Mounting Bracket

12

Mounting: Low Proﬁle

22

Mounting: Standard

30

Mounting: Universal

42

Test Your Fan 54

Models: K3150-A2, K3150-S0, K3150-X2

Installation Guide

For operation, maintenance, and

troubleshooting information, visit

bigassfans.com/support

NOTES

3

HAIKU

®

BY BIG ASS FANS

Disconnect power to the fan location! Do not use the fan with a dimmer switch!

A licensed electrician must install the fan if required by your local electrical code.

The ground wire must be connected to the supply ground and its length must be longer than the

safety cable!

Technical Speciﬁcations

Diameter Weight Operating voltage Operating frequency

132 cm ≤ 6.4 kg 100–240 VAC, 1 Φ 50–60 Hz

152 cm ≤ 7.3 kg 100–240 VAC, 1 Φ 50–60 Hz

213 cm ≤ 11.3 kg 100–240 VAC, 1 Φ 50–60 Hz

Tools Needed

• Ladder

• Wire Strippers

• Phillips Screwdriver

• Wrenches

Box Contents

As you remove the fan from its packaging, make sure you are not missing any components required for

assembly and operation. If you ordered multiple fans, be sure to keep the components of each fan together!

!

4

PARTS & HARDWARE: LOW PROFILE MOUNT

Use the two screw caps that match the color of your fan.

Safety cable not shown.

†

††

Mounting plate

(2) Rubber bumper

(2) Mounting bracket

Lower cover

Lower cover trim

(3) Airfoil

Motor hub

(2) Extension tube screw cap†

Remote control

Mounting hardware

• (4) 6 mm Nylock nut

• Safety cable shackle††

Airfoil hardware

• (6) M5 airfoil screw

• (6) 5 mm lock washer

Wiring hardware

• Wire connectors

• Wire nut

• (2) Wiring cover screw

a

b

g

d

j

e

f

k

c

h

a

b

c

d

e

f

g

h

i

j

k

l

i

l

5

HAIKU

®

BY BIG ASS FANS

PARTS & HARDWARE: STANDARD MOUNT

Rubber bushing

Mounting bracket†

(2) Mounting brace bracket

Wiring cover

Wiring cover trim

Lower cover

Lower cover trim

(3) Airfoil

Motor hub

Remote control

Mounting hardware

• (2) M6 x 1 x 25 mm socket cap screw††

• (2) M6 x 1 nylock nut††

• M8 Bolt

• 8 mm ﬂat washer

• 8 mm lock washer

• M8 nut

• 2 mm x 2 mm split pin

• Safety cable shackle†††

Airfoil hardware

• (6) M5 airfoil screw

• (6) 5 mm lock washer

Wiring hardware

• Wire connectors

• Wire nut

• (2) Wiring cover screw

a

b

c

d

e

f

g

h

i

j

k

l

m

a

b

g

d

e

f

c

h

l

i

k k

j

m

Do not use the mounting bracket if mounting the fan to a concrete ceiling.

If installing the fan to a junction box, U-shaped ceiling hook, or wood ceiling joist, only

one (1) bolt and one (1) nut are needed. If installing the fan to a J-shaped ceiling hook,

two (2) bolts and two (2) nuts are needed.

Safety cable not shown.

†

††

†††

6

PARTS & HARDWARE: UNIVERSAL MOUNT

Mounting bracket

Mounting ball & wedge

Canopy

Extension tube

Wiring cover

(3) Airfoil

Motor hub

Lower cover

Lower cover trim

Remote control

Mounting hardware

• 4 mm self-tapping screw

• 6 mm steel pin

• (6) M4 x 10 mm screw

• (2) M4 lock washer

• Safety cable shackle†

• M6 x 32 mm bolt

• M6 nut

Airfoil hardware

• (6) M5 airfoil screw

• (6) 5 mm lock washer

Wiring hardware

• Wire connectors

• Wire nut

• Cable tie

a

b

c

d

e

f

g

h

i

j

k

l

m

Safety cable not shown.†

a

b

g

d

e

f

k

i

c

h

l

j

m

7

HAIKU

®

BY BIG ASS FANS

1

PREPARE THE FAN SITE

Installation requires basic electrical knowledge. Contact a licensed electrician if you are uncomfortable

performing electrical work!

2

1

Disconnect Power!

If you are installing the fan directly to the building structure

or to a ceiling-mounted outlet box, the structure or outlet

box must be suitable for fan support.

Disconnect power to the fan location before wiring

the fan!

Mounting Structure

A readily accessible disconnect device shall be

incorporated external to the equipment.

c

b

a

8

INSTALL THE AIRFOILS

2

Make sure the stickers on the airfoils match the stickers on the fan hub!

1 2

INSTALL AIRFOILS REMOVE PROTECTIVE COVER

9

HAIKU

®

BY BIG ASS FANS

Moving clockwise around the fan, align each airfoil on the fan hub and secure it with the screws and

washers. Make sure the stickers on the airfoils match the stickers on the fan hub.

Hardware:

a. M5 airfoil screw

b. 5 mm lock washer

Remove and recycle the plastic protective cover (c).

2

1

STEPS COMPLETED

10

INSTALL THE LOWER COVER AND TRIM

3

If you purchased the Haiku Light Kit, proceed to the instructions included with the kit. Return to these

instructions once the kit is installed.

1 2

INSTALL LOWER COVER INSTALL LOWER COVER TRIM

11

HAIKU

®

BY BIG ASS FANS

STEPS COMPLETED

Position the lower cover over the fan motor, and then place both hands ﬂat on the cover and turn it

clockwise to lock it in place.

Align the four slots on the lower cover trim with the four small round tabs on the fan hub. Press and turn

the lower cover trim clockwise to lock it into place.

2

1

12

INSTALL THE MOUNTING BRACKET

Outlet Box

If your local electrical code requires the fan to be installed on a ceiling-mounted outlet box, the outlet box must be

suitable for fan support. If there is not an outlet box at the fan location, one should be installed on a ceiling joist or

beam and properly wired.

Concrete Ceiling

If installing your fan on a concrete ceiling, ensure power wiring has been routed to the fan site.

Low Proﬁle Mount. Attach the mounting plate directly to the ceiling using four Ø 8 mm anchor bolts. If required by your

local building and safety code, install a Ø 14 mm anchor hook for the safety cable.

Standard Mount. Install the fan where there is a ceiling hook or other sufficient structural support. If there is not a hook

at the fan site, install a hanger plate using three Ø 12–12.5 mm anchor bolts. Do not use the mounting bracket supplied

with the fan. If required by your local building and safety code, install an Ø 8–8.5 mm anchor hook for the safety cable.

Universal Mount. Attach the mounting bracket directly to the ceiling using three Ø 6 mm anchor bolts. If required by

your local building and safety code, install an Ø 8 mm anchor hook for the safety cable.

Wood Ceiling Joist

If installing your fan on a wood ceiling joist, ensure power wiring has been routed to the fan site. Attach the mounting

plate or mounting bracket directly to the joist using two wood screws (not supplied). Big Ass Fans recommends using

corrosion-resistant 12-11 x 45 mm hex head timber screws with seal.

13

HAIKU

®

BY BIG ASS FANS

Outlet Box

Page 14

4a

Concrete Ceiling

Page 16

4b

Wood Ceiling Joist

Page 18

4c

14

INSTALL THE MOUNTING BRACKET (OUTLET BOX)

4a

a

b

Low Proﬁle Mount Standard Mount Universal Mount

b

Installation may vary. Refer to the outlet

box instructions.

Installation may vary. Refer to the outlet

box instructions.

Installation may vary. Refer to the outlet

box instructions.

b

15

HAIKU

®

BY BIG ASS FANS

Make sure power is disconnected from the fan location before installing the mounting plate or

mounting bracket!

If installing a Standard Mount fan, seat the rubber bushing (a) in the eye of the mounting bracket.

Secure the mounting plate or mounting bracket (b) to the outlet box with the hardware supplied with the

outlet box. Refer to the outlet box instructions.

If installing a Universal Mount fan to a sloped ceiling, secure the mounting bracket so that the open side of

the bracket is facing up the slope of the ceiling.

!

50 mm max

40 mm max

ac

40 mm

Ø 8 mm

(anchor bolt)

Ø 14 mm

(anchor hook)

80 mm

100 mm

b

Ø 12–12.5 mm

35 mm 35 mm

45 mm

b

35–40 mm

ac

50 mm max

40 mm max

ac

Ø 6 mm

112 mm

45 mm 43 mm

b

16

INSTALL THE MOUNTING BRACKET (CONCRETE CEILING)

4b

Standard Mount Universal Mount

Install an anchor hook for the safety cable if required by your local building and safety code.

Low Proﬁle Mount

17

HAIKU

®

BY BIG ASS FANS

!

Make sure power is disconnected from the fan location before installing the mounting plate or

mounting bracket!

Low Proﬁle Mount

Drill four Ø 8 mm holes in the pattern shown. The hole depth should not exceed 40 mm.

Remove any dust from the holes. Insert four anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the bolt

sleeves are ﬂush with the ceiling surface.

Position the mounting plate (b) on the anchor bolts. Ensure all four anchor bolts are fully tightened to expand and lock the anchors.

If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill a Ø 14 mm hole for the anchor hook in the

pattern shown. The hole depth should not exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.

Standard Mount

Drill three Ø 12–12.5 mm holes in the pattern shown. The hole depth should not exceed 35–40 mm.

Remove any dust from the holes. Insert three anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the

bolt sleeves are flush with the ceiling surface.

Position the hanger plate (b) on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.

If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill an Ø 8–8.5 mm hole for the anchor hook

adjacent to the hanger plate. The hole depth should not exceed 35–40 mm. Remove any dust from the hole, and then insert the anchor hook

and fully tighten.

Universal Mount

Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed 40 mm.

Remove any dust from the holes. Insert three anchor bolts (a) into the holes. Strike the heads of the anchor bolts with a hammer, ensuring the

bolt sleeves are flush with the ceiling surface.

Position the mounting bracket (b) on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.

If required by local building and safety codes, install an anchor hook (c) for the safety cable. Drill an Ø 8 mm hole for the anchor hook. The hole

depth should not exceed 50 mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.

18

INSTALL THE MOUNTING BRACKET (WOOD CEILING JOIST)

4c

Standard Mount Universal MountLow Proﬁle Mount

b

a

b

ceiling joist

Not Supplied

b

Not Supplied

La page est en cours de chargement...

Big Ass Fans Haiku I Series Guide d'installation

Big Ass Fans Haiku I Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents