Kelvinator KG7T(C,L) Guide d'installation

Marque: Kelvinator

Modèle: KG7T(C,L)

Taper: Guide d'installation

Ce manuel convient également à

Two-Stage Condensing gas Furnaces With Fixed & Variable Speed Blowers 95.0% AFUE

INSTALLATION INSTRUCTIONS

*TL Downﬂow Furnace

*TC Upﬂow / Horizontal Furnace

WARNING

FIRE OR EXPLOSION HAZARD





supplier.





WHAT TO DO IF YOU SMELL GAS











DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION .............................. 3

REQUIREMENTS & CODES ..............................................4

Combustion Air Quality....................................................5

Heating Load ...................................................................5

Installation in a Garage....................................................5

Clearances to Combustible Materials .............................6

Operation of Furnace During Construction .....................6

COMBUSTION AIR & VENTING REQUIREMENTS ..........7

Direct Vent Systems ........................................................8

Conventional Vent Systems - Conﬁned Spaces ..............8

Air From Inside .............................................................. 8

Outdoor Air from a Crawl Space or Vented Attic ........... 8

Outdoor Air Using Vertical Ducts ..................................8

Outdoor Air Using Horizontal Ducts ..............................8

Air Directly Through an Exterior Wall ............................9

Alternate Method of Providing Air from Outside: ...........9

Conventional Vent Systems - Unconﬁned Spaces ..........10

Category IV Venting .........................................................10

Vent Pipe Material ......................................................... 11

Vent Pipe Length & Diameter ........................................11

Vent Pipe Installation ....................................................11

Outdoor Terminations - Horizontal Venting ...................12

Outdoor Terminations - Vertical Venting .......................13

Vent Freezing Protection ...............................................13

Existing Installations ......................................................13

Condensate Disposal ......................................................13

CIRCULATING AIR REQUIREMENTS ............................... 14

Plenums & Air Ducts ........................................................14

Return Air Connections ...................................................14

Upﬂow & Horizontal Furnaces ....................................... 14

Downﬂow Furnaces .......................................................15

Supply Air Connections ...................................................15

Acoustical Treatments .....................................................15

FURNACE INSTALLATION ................................................ 15

General Requirements ....................................................15

Upﬂow Furnaces .............................................................. 15

Horizontal Furnaces ........................................................15

Downﬂow Furnaces .........................................................16

Installation on a concrete slab .......................................16

Inducer & Venting Options ...............................................16

Inducer Assembly Rotation ...........................................17

Pressure Switch Tubing ................................................17

Accessories .....................................................................17

Finish Flange .................................................................17

Rubber Grommets .........................................................18

PVC Components .........................................................18

Typical Orientation .................................................18

Alternate Orientation ..............................................18

Condensate Drain Lines ................................................19

Bottom Panel Removal ....................................................19

Alternate Bottom Panel Removal ..................................19

GAS SUPPLY & PIPING .....................................................20

Leak Check ...................................................................... 22

High Altitude Application (Natural Gas Only) ..................22

Converting from Natural Gas to LP / Propane .................23

ELECTRICAL WIRING .......................................................23

Line Voltage Wiring..........................................................23

Grounding ........................................................................24

Thermostat / Low Voltage Connections ..........................24

Single Stage AC & Two Stage Thermostat ...................25

Two-Stage AC & Two-Stage Thermostat ......................25

Autostaging for Single Stage Thermostats ......................25

Autostaging for Two-Stage Thermostats .........................26

Blower Speed Conﬁguration ............................................26

Fixed Speed Blower Applications ..................................26

Variable Speed Blower Applications .............................26

Dehumidiﬁcation Options ................................................26

START-UP & ADJUSTMENTS ...........................................27

Pre-Start Check List ........................................................27

Start-up Procedures ........................................................27

Verifying & Adjusting Input Rate ...................................... 27

Verifying & Adjusting Temperature Rise ..........................27

Heat Anticipator ...............................................................27

Verifying Burner Operation ..............................................28

Verifying Operation of the Supply Air Limit Switch .......... 28

OPERATING SEQUENCE ..................................................29

Heating Cycle ..................................................................29

Cooling Cycle ..................................................................29

Fan Mode .........................................................................29

MAINTENANCE ..................................................................29

FIGURES & TABLES ..........................................................31

Figure 28. *TC & *TL Cabinet Dimensions .................... 31

Airﬂow Data .....................................................................32

Table 6. *TC / *TL Heating / Cooling Airﬂows (CFM)

& Temperature Rises (°F) ................................32

Table 7. *TC / *TL Nominal Heating Airﬂows

(CFM) & Temperature Rises (° F) for Variable

Speed Furnaces ...............................................34

Table 8. *TC / *TL Nominal Cooling / Heat Pump

Airﬂows (CFM)for Variable Speed Furnaces ...35

Gas Information ...............................................................36

Table 9. Gas Flow Rates ...............................................36

Table 10. Gas Pipe Capacities ......................................36

Table 11. High Altitude Deration - Propane Gas ...........37

Table 12. Natural Gas Heating Values ..........................37

Table 13. High Altitude Deration - Natural Gas with

HIGH Heating Value ......................................38

Table 14. High Altitude Deration - Natural Gas with

LOW Heating Value .......................................38

Electrical Information .......................................................39

Figure 29. Two-Stage Fixed Speed Motor Control

Board ............................................................39

Figure 31. Two-Stage Furnace Control Board ..............39

Figure 30. Two-Stage Variable Speed

Motor Control Board .....................................39

Figure 32. Wiring Diagram for Two-Stage, Fixed

Speed Upﬂow Furnaces ...............................40

Figure 33. Wiring Diagram for Two-Stage, Fixed

Speed Downﬂow Furnaces ..........................41

Figure 34. Wiring Diagram for Two-Stage, Variable

Speed Upﬂow Furnaces ...............................42

Figure 35. Wiring Diagram for Two-Stage, Variable

Speed Downﬂow Furnaces ..........................43

WARNING:

    





      

   



be used with this product.

WARNING:





      









• Tominimizeequipmentfailureorpersonalinjury,itis

essential that only qualiﬁed individuals install, service, or

maintain this equipment. If you do not posses mechanical

skills or tools, call your local dealer for assistance.

• Followallprecautionsinthe literature, on tags, and

on labels provided with the equipment. Read and

thoroughly understand the instructions provided with

the equipment prior to performing the installation and

operational checkout of the equipment.

• Usecautionwhenhandlingthisapplianceorremoving

components. Personal injury can occur from sharp metal

edges present in all sheet metal constructed equipment.

• Donotstoreanyofthefollowingon,orincontactwith,

the unit: Rags, brooms, vacuum cleaners, or other

cleaning tools, spray or aerosol cans, soap powders,

bleaches, waxes, cleaning compounds, plastics or

plastic containers, paper bags or other paper products,

gasoline, kerosene, cigarette lighter ﬂuid, dry cleaning

ﬂuids, paint thinners, or other volatile ﬂuids.

• Theinstallershouldbecomefamiliarwiththeunitswiring

diagram before making any electrical connections to

the unit. See Figure 32 (page 40), Figure 33 (page 41),

Figure 34 (page 42), & Figure 35 (page 43) or the unit

wiring label.

        





IMPORTANT SAFETY INFORMATION

INSTALLER: Please read all instructions before servicing

this equipment. Pay attention to all safety warnings and

any other special notes highlighted in the manual. Safety

markings are used frequently throughout this manual to

designate a degree or level of seriousness and should

not be ignored.

WARNING - indicates a potentially hazardous situation

that if not avoided, could result in personal injury or death.

CAUTION - indicates a potentially hazardous situation

that if not avoided, may result in minor or moderate injury

or property damage.

WARNING:





     





    

     



WARNING:

     





Venting Information ..........................................................44

Table 15. Vent Termination Clearances ........................ 44

Figure 36. Horizontal & Vertical Venting

(A Width Cabinets) .......................................45

Figure 37. Horizontal & Vertical Venting

(B, C, & D Width Cabinets) ..........................46

Figure 38. Horizontal & Vertical Venting

(B, C, & D Width Cabinets) ..........................47

Figure 39. Upﬂow Venting Options

(B, C, & D Width Cabinets) ..........................48

Figure 40. Horizontal Venting Options

(A Width Cabinets) .......................................49

Figure 41. Horizontal Venting Options

(B, C, & D Width Cabinets) ..........................50

Figure 42. Downﬂow Options ........................................51

TROUBLESHOOTING ........................................................52

Table 16. Furnace Control Board Fault Conditions .......52

Table 17. Motor Control Board Fault Conditions ...........52

FURNACE COMPONENTS ................................................52

Figure 43. Component Locations ..................................53

INSTALLATION / PERFORMANCE CHECK LIST ............112

REQUIREMENTS & CODES

WARNING:

      

     



    

     



• This furnace must be installed in accordance with

these instructions, all applicable local building codes

and the current revision of the National Fuel Gas Code

(NFPA54/ANSI Z223.1) or the Natural Gas and Propane

Installation Code, CAN/CGA B149.1.

• Useonlywithtypeofgasapprovedforthisfurnace.

Refer to the furnace rating plate.

• Installthisfurnaceonlyinalocationandpositionas

speciﬁed on page 6.

• Provideadequatecombustionandventilationairtothe

furnace space as specified on page 7, page 8,

page 9, & page 10.

• Provideadequateclearancesaroundtheventairintake

terminal as speciﬁed in Figure 7 (page 12), Figure 8 (page

12)

, Figure 9 (page 12), & Figure 10 (page 12).

• Combustion products must be discharged outdoors.

Connect this furnace to an approved vent system only,

as speciﬁed on page 10, page 11, page 12, & page

• Never test for gas leaks with an open ame. Use

a commercially available soap solution to check all

connections. See page 22.

• Thisfurnaceisdesignedtooperatewithamaximum

external pressure rise of 0.5 inches of water column.

Consult Table 6 (page 32), Table 7 (page 34), & Table 8

(page 35)

, and the rating plate for the proper circulating

air ﬂow and temperature rise. It is important that the duct

system be designed to provide the correct ﬂow rates

and external pressure rise. An improperly designed duct

system can result in nuisance shutdowns, and comfort

or noise issues.

• Whensupplyductscarryaircirculatedbythefurnace

to areas outside the space containing the furnace, the

return air shall also be handled by duct(s) sealed to

the furnace casing and terminating in the conditioned

space. See page 14.

• Agas-redfurnaceforinstallationinaresidentialgarage

must be installed as speciﬁed on page 5.

• Thisfurnaceisnotapprovedforinstallationinmobile

homes. Installing this furnace in a mobile home could

cause ﬁre, property damage, and/or personal injury.

• The Commonwealth of Massachusetts requires

compliance with regulation 248 CMR 4.00 and 5.00 for

installation of through – the – wall vented gas appliances

as follows:

1. For direct-vent appliances, mechanical-vent heating

appliances or domestic hot water equipment, where the

bottom of the vent terminal and the air intake is installed

below four feet above grade the following requirements

must be satisﬁed:

a.) A carbon monoxide (CO) detector and alarm shall

be placed on each ﬂoor level where there are

bedrooms. The detector shall comply with NFPA

720 (2005 Edition) and be mounted in the living

area outside the bedroom(s).

b.) A (CO) detector shall be located in the room that

houses the appliance or equipment and shall:

•Bepoweredbythesameelectricalcircuitasthe

appliance or equipment. Only one service switch

shall power the appliance and the (CO) detector;

•Havebatteryback-uppower;

•MeetANSI/UL2034Standardsandcomplywith

NFPA 720 (2005 Edition); and Approved and listed

by a Nationally Recognized Testing Laboratory

as recognized under 527 CMR.

c.) A Product-approved vent terminal must be

used, and if applicable, a product-approved air

intake must be used. Installation shall be in strict

compliance with the manufacturer’s instructions.

A copy of the installation instructions shall remain

with the appliance or equipment at the completion

of the installation.

d.) A metal or plastic identiﬁcation plate shall be

mounted at the exterior of the building, four feet

directly above the location of vent terminal. The

plate shall be of sufﬁcient size, easily read from

a distance of eight feet away, and read “Gas Vent

Directly Below”.

2. For direct-vent appliances, mechanical-vent heating

appliances or domestic hot water equipment where the

bottom of the vent terminal and the air intake is installed

above four feet above grade the following requirements

must be satisﬁed:

a.) A (CO) detector and alarm shall be placed on each

ﬂoor level where there are bedrooms. The detector

shall comply with NFPA 720 (2005 Edition) and be

mounted in the living area outside the bedroom(s).

b.) The (CO) detector shall:

•Belocatedintheroomthathousestheappliance

or equipment;

•Behard-wiredorbatterypoweredorboth.

•ShallcomplywithNFPA720(2005Edition).

c.) A product-approved vent terminal must be

used, and if applicable, a product-approved air

intake must be used. Installation shall be in strict

compliance with the manufacturer’s instructions.

A copy of the installation instructions shall remain

with the appliance or equipment at the completion

of the installation.

The information listed below is for reference purposes only

and does not necessarily have jurisdiction over local or

state codes. Always consult with local authorities before

installing any gas appliance.



• US:NationalFuelGasCode(NFGC),AirforCombustionand

Ventilation

• CANADA: Natural Gas and Propane Installation Codes

(NSCNGPIC), Venting Systems and Air Supply for Appliances



• USandCANADA:AirConditioningContractorsAssociation

(ACCA) Manual D, Sheet Metal and Air Conditioning

Contractors National Association (SMACNA), or American

Society of Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE) Fundamentals Handbook

Electrical Connections

• US:NationalElectricalCode(NEC)ANSI/NFPA70

• CANADA:CanadianElectricalCodeCSAC22.1

Gas Piping & Gas Pipe Pressure Testing

• US:NFGCandNationalPlumbingCodes

• CANADA:NSCNGPIC

General Installation

• US:Currentedition of theNFGCandtheNFPA 90B.For

copies, contact the National Fire Protection Association Inc.,

Batterymarch Park, Quincy, MA 02269; or American Gas

Association, 400 N. Capitol, N.W., Washington DC 20001 or

www.NFPA.org

• CANADA:NSCNGPIC.Foracopy,contactStandardSales,

CSA International, 178 Rexdale Boulevard, Etobicoke

(Toronto), Ontario, M9W 1R3 Canada



• US:(NFGC)NFPA54–1999/ANSIZ223.1andtheInstallation

Standards, Warm Air Heating and Air Conditioning Systems

ANSI/NFPA 90B.

• CANADA:CAN/CGA-B149.1and.2–M00NationalStandard

of Canada. (NSCNGPIC)



CAUTION:

       



To maximize heat exchanger life, the combustion air

must be free of chemicals that can form corrosive acidic

compounds in the combustion gases. The recommended

source of combustion air is to use outdoor air. However,

the use of indoor air in most applications is acceptable

except as listed:

• If the furnace is installed in a conned space, it is

required that the necessary combustion air come from

the outdoors by way of attic, crawl space, air duct, or

direct opening. For Installations in conﬁned spaces, see

page 7 for combustion air requirements.

• Installationsintheselocationsmayrequireoutdoorair

for combustion, due to chemical exposures:

Commercial buildings

Buildings with indoor pools

Furnaces installed in laundry rooms

Furnaces installed in hobby or craft rooms

Furnaces installed near chemical storage areas

• Exposuretothefollowingsubstancesinthecombustion

air supply may require outdoor air for combustion:

Permanent wave solutions

Chlorinated waxes and cleaners

Chlorine based swimming pool chemicals

Water softening chemicals

De-icing salts or chemicals

Carbon Tetrachloride

Halogen type refrigerants

Cleaning solvents (perchloroethylene)

Printing inks, paint removers, varnishes, etc.

Hydrochloric Acid

Cements and glues

Antistatic fabric softeners

Masonry acid washing materials

Heating Load

This furnace should be sized to provide the design heating

load requirement. Heating load estimates can be made

using approved methods available from Air Conditioning

Contractors of America (Manual J); American Society of

Heating, Refrigerating, and Air Conditioning Engineers;

or other approved engineering methods. 

       

. The ductwork should

be appropriately sized to the capacity of the furnace to

ensure its proper airﬂow rating.

For installations above 2,000 ft., the furnace should have

a sea level input rating large enough that it will meet the

heating load after deration for altitude.

Two-stage furnaces operate at two input rates to better

meet heating loads. The lower heating rate (low ﬁre) is

65% of the high ﬁre rate. The greatest degree of control

over the furnace can be gained by controlling it with a two

stage thermostat. This allows the thermostat to directly

request either high or low ﬁre. However, it is possible to

operate the furnace using a single stage thermostat. In

this application the furnace control can be set to increase

from low to high ﬁre, based on a timer. See Autostaging

for Single Stage Thermostats (page 25).

Furnaces are properly sized to meet the expected

maximum heating load. But this load occurs infrequently.

So, during more moderate weather, the furnace is likely to

use low ﬁre a considerable part of the time. This is normal

and has the beneﬁt of quieter and more efﬁcient operation.

Installation in a Garage

This Gas-ﬁred furnace may be installed in a residential

garage with the provision that the burners and igniter

are located no less than 18 inches (457mm) above the

ﬂoor. The furnace must be located or protected to prevent

physical damage by vehicles.

TOP

FRONT

UPFLOW

APPLICATIONS

HORIZONTAL

APPLICATIONS

VENT

TOP

FRONT

DOWNFLOW

APPLICATIONS

SIDE

TOP

BOTTOM

VENT

FRONT

BACK

SIDE

LEFT SIDE

RIGHT SIDE

CLEARANCES TO COMBUSTIBLE MATERIALS

Left Side ................. 0 Inches

Top ..........................0 Inches

Right Side ............... 0 Inches

Front ........................

†

4 Inches

Vent ........................ 0 Inches Back........................ 0 Inches



clearance is 36 in.

Figure 1. 



WARNING:



        









This furnace is Design Certiﬁed in the U.S. and Canada

by CSA International for the minimum clearances to

combustible materials. NOTE: The furnace is listed for

installation on combustible or non-combustible ﬂooring.

However, wood is the only combustible ﬂooring allowed

for installation. Downﬂow models must use the appropriate

subase kit when installing over a wood ﬂoor. To obtain

model number and speciﬁc clearance information, refer

to the furnace rating plate, located inside of the furnace

cabinet.

Access for positioning and servicing the unit must be

considered when locating unit. The need to provide

clearance for access to panels or doors may require

clearance distances over and above the requirements.





See Figure 1 for minimum clearance requirements.



CAUTION:

    



     

       







COMBUSTION AIR & VENTING

REQUIREMENTS

WARNING:

CARBON MONOXIDE POISONING HAZARD

      



     



      



     

while all other appliances connected to the



      













      







and windows and all doors between the space

in which the appliance(s) connected to the







      







      



6. Follow the lighting instructions. Place the

appliance being inspected into operation.





      

      









corrected in accordance with the National Fuel





Codes.

      

     





     



IMPORTANT INFORMATION:

 













the NFGC.

 



with the National Fuel Gas Code (NFGC) and all

applicable local codes.

      

      







    





        

cause corrosion. The inlet pipe should not be placed



page 5.

WARNING:

     





      





WARNING:

       

       

 



      





building chase.

This condensing furnace is certiﬁed for installation either as

a Direct Vent (2-pipe) or Conventional (1-pipe) appliance.

Direct Vent appliances draw combustion air from the

outdoors and vent combustion products back outside.

Installation with air taken from around the furnace is often

referred to as Conventional installation - i.e. only the vent

(exhaust) pipe is provided.

Another important consideration when selecting one or

two pipe installation is the quality of the Indoor air which

can sometimes be contaminated with various household

chemicals . These chemicals can cause severe corrosion

in the furnace combustion system. A 2-pipe installation

has the additional advantage that it isolates the system

from the effects of negative pressure in the house.

CAUTION:















    



Fuel Gas Code.

Air openings on top of the furnace and openings in closet

doors or walls must never be restricted. If the furnace is

operated without adequate air for combustion, the ﬂame

roll-out switch will open, turning off the gas supply to the

burners.

IMPORTANT NOTE





 









Direct vent appliances draw combustion air from the

outdoors and vent combustion products back outside,

isolating the entire system from the indoor space. It is

important to make sure that the whole system is sealed

and clearances to combustibles are maintained regardless

of the installation being in a conﬁned or unconﬁned space.

    

Spaces

A conﬁned space is an area with volume less than 50

cubic feet per 1,000 Btuh of the combined input rates of

all appliances drawing combustion air from that space.

Furnace closets, small equipment rooms and garages are

conﬁned spaces. Furnaces installed in a conﬁned space

which supply heated air to areas outside the space must

draw return air from outside the space and must have the

return air ducts tightly sealed to the furnace. Ducts must

have cross - sectional area at least as large as the free area

of their respective openings to the furnace space. Attics

or crawl spaces must connect freely with the outdoors if

they are the source of air for combustion and ventilation.

The required sizing of these openings is determined by

whether inside or outside air is used to support combustion,

the method by which the air is brought to the space, and

by the total input rate of all appliances in the space. In

all cases, the minimum dimension of any combustion air

opening is 3 inches.

Air From Inside

If combustion air is taken from the heated space, the two

openings must each have a free area of at least one square

inch per 1,000 Btuh of total input of all appliances in the

conﬁned space, but not less than 100 square inches of

free area. See Example and Figure 2.

EXAMPLE

If the combined input rate of all appliances is less than

or equal to 100,000 Btuh, each opening must have

a free area of at least 100 in

. If the combined input

rate of all appliances is 120,000 Btuh, each opening

must have a free area of at least 120 in

Outdoor Air from a Crawl Space or Vented

Attic

When the openings can freely exchange air with the

outdoors, each opening shall have a minimum free area

of 1 square inch per 4,000 Btuh of total appliance input.

The openings shall exchange directly, or by ducts, with

the outdoor spaces (crawl or attic) that freely exchange

with the outdoors. See Figure 3 (page 9).

Outdoor Air Using Vertical Ducts

If combustion air is taken from outdoors through vertical

ducts, the openings and ducts must have a minimum free

area of one square inch per 4,000 Btuh of total appliance

input. See Figure 4 (page 9).

Figure 2. 

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

38,000 100 sq. In 12 inches

60,000 100 sq. In 12 inches

80,000 100 sq. In 12 inches

100,000 100 sq. In 12 inches

120,000 120 sq. In 13 inches

140,000 140 sq. In 14 inches

160,000 160 sq. In 15 inches

Vent or

Chimney

Furnace

Water

Heater

12” Max.

See

Notes

See

Notes

NOTES:

Each opening must be

at least 100 sq. in. or

1 sq. in. per 1,000 Btuh

of total input rating,

whichever is greater.

Openings must start at

no more than 12 inches

from the top and bottom

of the enclosure.

Outdoor Air Using Horizontal Ducts

If combustion air is taken from outdoors through horizontal

ducts, the openings and ducts must have a minimum free

area of one square inch per 2,000 Btuh of total appliance

input. Ducts must have cross - sectional area at least as

large as the free area of their respective openings to the

furnace space. See Figure 5.

Air Directly Through an Exterior Wall

If combustion air is provided directly through an exterior

wall, the two openings must each have free area of at

least one square inch per 4,000 Btuh of total appliance

input. See Figure 6.

Figure 4. 

Through Vertical Ducts

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

38,000 10 sq. In 4 inches

60,000 15 sq. In 5 inches

80,000 20 sq. In 5 inches

100,000 25 sq. In 6 inches

120,000 30 sq. In 6 inches

140,000 35 sq. In 7 inches

160,000 40 sq. In 8 inches

Air Duct must be

at least 1 sq. in.

per 4,000 Btuh of

total input rating.

Ducts must

extend above

attic insulation.

Air Duct must be

at least 1 sq. in.

per 4,000 Btuh of

total input rating.

Ventilation Louvers

at each end of attic

Attic

Insulation

12" Max

Furnace

Water

Heater

Vent or

Chimney

Water

Heater

Vent or

Chimney

Furnace

Ventilation Louvers For

Unheated Crawl Space

Inlet Air

Ventilation Louvers

(each end of attic)

NOTE: Air openings shall

each have a free area of

not less than one square

inch per 4,000 Btuh of the

total input rating of all

equipment in the enclosure

Alter

nate

Air Inlet

Outlet

Air

Figure 3. 

Space or Vented Attic

Figure 5. 

Through Horizontal Ducts

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

38,000 20 sq. In 5 inches

60,000 30 sq. In 6 inches

80,000 40 sq. In 7 inches

100,000 50 sq. In 8 inches

120,000 60 sq. In 9 inches

140,000 70 sq. In 10 inches

160,000 80 sq. In 10 inches

Furnace

Water

Heater

Air Ducts must be

at least 1 sq. in.

per 2,000 Btuh of

total input rating.

Vent or

Chimney

Air Duct

TOTAL INPUT

RATING (BTUH)

MINIMUM FREE AREA

(EACH OPENING)

ROUND DUCT

DIAMETER

38,000 10 sq. In 4 inches

60,000 15 sq. In 5 inches

80,000 20 sq. In 5 inches

100,000 25 sq. In 6 inches

120,000 30 sq. In 6 inches

140,000 35 sq. In 7 inches

160,000 40 sq. In 8 inches

NOTE:

Each opening to outside

must be at least 1 sq. in. per

4,000 Btuh of total input rating.

12" Max.

Furnace

Water

Heater

Vent or

Chimney

12"

Max

See

Note

See

Note

Figure 6. 

Through an Exterior Wall

Alternate Method of Providing Air from Out-

side:

If acceptable under local Codes, it is permitted to provide

outside air using one opening (See NFGC). Generally,

conﬁned spaces must have 2 openings in the space for

combustion air. One opening must be within 12 inches of

the ceiling, and the other must be within 12 inches of the

ﬂoor. However, an alternative method recently adopted by

the NFGC uses one opening within 12 inches of the top

of the space. This method may be used if it is acceptable

to the local codes.

THE FOLLOWING CONDITIONS MUST BE MET:

1. The opening must start within 12” of the top of the

structure and connect with the out of doors through

vertical or horizontal ducts or be ducted to a crawl or

attic space that connects with the out of doors.

2. The opening must have a minimum free area of 1 in

per 3,000 Btu per hour of the total input rating of all

equipment located in the enclosure.

3. The free area must not be less than the sum of all the

areas of the vent connectors in the enclosure.

    

Spaces

An unconﬁned space is an area including all rooms not

separated by doors with a volume greater than 50 cubic

feet per 1,000 Btuh of the combined input rates of all

appliances which draw combustion air from that space.

In general, a furnace installed in an unconﬁned space will

not require outside air for combustion. However, in homes

built for energy efﬁciency (low air change rates), it may

be necessary to provide outside air to ensure adequate

combustion and venting, even though the furnace is located

in an unconﬁned space. See Example below.

EXAMPLE

A space with a water heater rated at 45,000 Btuh input

and a furnace rated at 75,000 Btuh requires a volume of

6,000 cubic feet [50 x (45 + 75) = 6,000] to be considered

unconﬁned. If the space has an 8 foot ceiling, the ﬂoor

area of the space must be 750 sq. ft. (6,000 / 8 = 750).



WARNING:

     

      

      



 





This furnace is classiﬁed as a “Category IV” appliance,

which requires special venting materials and installation

procedures. This section speciﬁes installation requirements

for Conventional (1-pipe) and Direct Vent (2-pipe) piping.

For 1- pipe installations, install vent piping as described in

this section and provide air for combustion and ventilation

according to page 7, page 8, page 9, & page 10.

The length of vent and combustion air piping for either

type of installation are shown in Table 1.

Table 1. Vent Pipe Lengths

FURNACE

MODELS

(BTU)

FURNACE

INSTALLATION

SINGLE VENT PIPE LENGTH (FT.)

WITH 1 LONG RADIUS ELBOW*

DUAL VENT PIPE LENGTH (FT.)

WITH 1 LONG RADIUS ELBOW ON EACH PIPE*

OUTLET

2” DIAMETER

OUTLET

3” DIAMETER

INLET / OUTLET

2” DIAMETER

INLET / OUTLET

3” DIAMETER

38,000

Upﬂow 90 90 90 90

Horizontal 50 90 50 90

60,000

Upﬂow 90 90 90 90

Horizontal 50 90 50 90

Downﬂow 30 90 30 90

80,000

Upﬂow 40 90 40 90

Horizontal 30 90 30 90

Downﬂow 30 90 30 90

100,000

Upﬂow 30 90 30 90

Horizontal 30 90 30 90

Downﬂow 30 90 25 90

120,000

Upﬂow N/A 90 N/A 90

Horizontal N/A 90 N/A 90

Downﬂow N/A 90 N/A 90

*NOTES:

1. Subtract 2.5 ft. for each additional 2 inch long radius elbow, 5 ft. for each additional 2 inch short radius elbow, 3.5 ft. for each additional 3 inch

long radius elbow, and 7 ft. for each additional 3 inch short radius elbow. Subtract 5 ft for each 2” tee and 8 ft for each 3” tee. Two 45 degree

elbows are equivalent to one 90 degree elbow.

2. This table applies for elevations from sea level to 2,000 ft. For higher elevations, decrease pipe lengths by 8% per 1,000 ft of altitude.

Category IV appliances operate with positive vent pressure

and therefore require vent systems which are thoroughly

sealed. They also produce liquid condensate, which is

slightly acidic and can cause severe corrosion of ordinary

venting materials. Furnace operation can be adversely

affected by restrictive vent and combustion air piping.

The inducer assembly on this furnace can be rotated to

vent the ﬂue products out of the left or right side of the

furnace. This increases the ﬂexibility of which direction

the vent pipe can exit the furnace.

Vent Pipe Material

Vent and combustion air pipe and ﬁttings must be one

of the following materials in the list and must conform to

the indicated ANSI/ASTM standards.

MATERIALS STANDARDS

Schedule 40PVC ............................................................... D1785

PVC-DWV .......................................................................... D2665

SDR-21 & SDR-26 ............................................................. D2241

ABS-DWV .......................................................................... D2661

Schedule 40 ABS .............................................................. F628

Foam / Cellular Core PVC ................................................. F891

*PolyPro

by DuraVent ...................................................... ULC-S636

CPVC ................................................................................. D1784

*When using PolyPro

, all venting and ﬁttings must be from the same

manufacturer with no interchanging of other materials. Refer to speciﬁc

instructions supplied with the PolyPro vent kits

Cement must conform to ASTM Standard D2564 for PVC

and Standard D2235 for ABS. PVC primer must meet

standard ASTM F656. When joining PVC piping to ABS,

use PVC solvent cement. (See procedure speciﬁed in

ASTM Standard D3138)

In Canada, all plastic vent pipes and ﬁttings including

any cement, cleaners, or primers must be certiﬁed as a

system to ULC S636. However this requirement does not

apply to the ﬁnish ﬂanges or piping internal to the furnace.

Vent Pipe Length & Diameter

In order for the furnace to operate properly, the combustion

air and vent piping must not be excessively restrictive.

• Theventingsystemshouldbedesignedtohavethe

minimum number of elbows or turns.

• Transitiontothenalventdiametershouldbedoneas

close to the furnace outlet as practical.

• Alwaysusethesamesizeoralargerpipeforcombustion

air that is used for the exhaust vent.

Table 1 indicates the maximum allowable pipe length for

a furnace of known input rate, when installed with piping

of selected diameter and number of elbows. To use the

table, the furnace input rate, the centerline length and the

number of elbows on each pipe must be known.

When estimating the length of vent runs, consideration

must be made to the effect of elbows and other ﬁttings.

This is conveniently handled using the idea of “equivalent

length”. This means the ﬁttings are assigned a linear

length that accounts for the pressure drop they will cause.

For example: a 2” diameter, long radius elbow is worth

the equivalent of 2.5 feet of linear run. A 90 degree tee

is worth 7 ft.

The equivalent lengths of tees and various elbows are

listed in Table 1 . Measure the linear length of the vent run

and then add in the equivalent length of each ﬁtting. The

total length, including the equivalent ﬁtting lengths, must

be less than the maximum length speciﬁed in Table 1.

Vent Pipe Installation

CAUTION:

       



This furnace has been certiﬁed for installation with zero

clearance between vent piping and combustible surfaces.

However, it is good practice to allow space for convenience

in installation and service.

• In the absence of local codes, the location of any

combustion air inlet relative to any vent terminal must

be at least 8 inches. This includes installations involving

more than one furnace.

• Thequalityofoutdoorairmustalsobeconsidered.Be

sure that the combustion air intake is not located near

a source of solvent fumes or other chemicals which

can cause corrosion of the furnace combustion system.

(See list of substances on

page 5).

• Routepipingasdirectaspossiblebetweenthefurnace

and the outdoors. Horizontal piping from inducer to

the ﬂue pipe must be sloped 1/4” per foot to ensure

condensate ﬂows towards the drain tee or PVC trap.

Longer vent runs require larger pipe diameters. Refer

to the Inducer & Venting Options section on page 17

for additional information.

• IfaDirectVent(2-pipe)systemisused,thecombustion

air intake and the vent exhaust must be located in the

same atmospheric pressure zone. This means both

pipes must exit the building through the same portion

of exterior wall or roof as shown in Figure 7, Figure 8,

Figure 9

, & Figure 10.

• Pipingmustbemechanicallysupportedsothatitsweight

does not bear on the furnace. Pipe supports must be

installed a minimum of every 5 feet along the vent run

to ensure no displacement after installation. Supports

may be at shorter intervals if necessary to ensure that

there are no sagging sections that can trap condensate.

See Figure 36 (page 45) and Figure 37 (page 46). It is

recommended to install couplings along the vent pipe,

on either side of the exterior wall. These couplings may

be required by local code.

• Ifbreakableconnectionsarerequiredinthecombustion

air inlet pipe (if present) and exhaust vent piping, then

straight neoprene couplings for 2” or 3” piping with

hose clamps can be used. These couplings can be

ordered through your local furnace distributor. To install

a coupling:

1. Slide the rubber coupling over the end of the pipe that

is attached to the furnace and secure it with one of the

hose clamps.

2. Slide the other end of the rubber coupling onto the other

pipe from the vent.

3. Secure the coupling with the second hose clamp,

ensuring that the connection is tight and leak free.

Outdoor Terminations - Horizontal Venting

• Vent and combustion air intake terminations shall

be installed as depicted in Figure 7 & Figure 8 and in

accordance with these instructions:

• Ventterminationclearancesmustbeconsistentwiththe

NFGC, ANSI 2223.1/NFPA 54 and/or the CSA B149.1,

Natural Gas and Propane Installation Code.

Table 15

(page 44)

lists the necessary distances from the vent

termination to windows and building air intakes.

• Vent and combustion air intake terminations must

be located to ensure proper furnace operation and

conformance to applicable codes. A vent terminal

must be located at least 3 feet above any forced air

inlet located within 10 feet. This does not apply to the

combustion air inlet of a direct vent (two pipe) appliance.

In Canada, CSA B149.1, takes precedence over these

instructions. See Table 15.

• Allminimumclearancesmustbemaintainedtoprotect

building materials from degradation by ﬂue gases. See

Figure 7.

• Foroptimalperformance,ventthefurnacethrougha

wall that experiences the least exposure to winter winds.

• The vent termination shall be located at least 3 ft.

horizontally from any electric meter, gas meter, regulator

and any relief equipment. These distances apply ONLY

to U.S. installations. In Canada, CSA B149.1, takes

precedence over these instructions.

• Donotinstalltheventterminalsuchthatexhaustis

directed into window wells, stairwells, under decks

or into alcoves or similar recessed areas, and do not

terminate above any public walkways.

• Ifventinghorizontally,asidewallventkitisavailable

according to the pipe diameter size of the installation.

For 2 inch pipe use side wall vent kit #904617, and

for 3 inch pipe use kit #904347.   



• Concentricventterminationkitsareavailableforuse

with these furnaces. For 2 Inch pipe use kit #904952

and for 3 inch pipe use kit # 904953. 



Figure 9. Alternate Horizontal Vent Installation

Support

NOTE: Vent Configuration to Provide

12" Minimum height above Snow Level.

1/2"

Armaflex

Insulation or

Equivalent

(if required)

12" Above

Maximum

Expected

Snow Level

19" Max.

(See Note)

Outside

Wall

12” min. to maximum

expected snow level

(both pipes)

90° Elbow

Exhaust vent

option B

Exhaust vent

option A

Mounting kit faceplate

secured to wall with screws

(both pipes)

Combustion

air inlet

Exhaust vent

option C

18” Min.

36” Max.

8” Min.

36” Max.

(all positions)

Figure 7. Inlet & Exhaust Pipe Clearances

Note 2

Mechanical draft

vent terminal

Direct vent

terminal

50,000 Btuh

or less

Forced air inlet

Direct vent

terminal - more

than 50,000 Btuh

Mechanical

draft vent

terminal

Mechanical

draft vent

terminal

Less

than

10 ft.

3 ft.

NOTES:

1. All dimensions shown are

minimum requirements.

2. Exterior vent terminations must

be located at least 12” above the

maximum expected snow level.

Note 2

4 ft

12 in.

9 in.

Note 2

Figure 8. Vent Locations

Figure 10. 

Combustion Air

Exhaust Vent

12” Above Maximum

Expected Snow Level

(Both pipes)

Elbows on the combustion air

inlet must be positioned pointing

away from the exhaust vent.

8" Min.

36" Max.

Plumbing Vent Roof Boot

(Both Pipes)

Existing Installations

When an existing furnace is removed from a vent system

serving other appliances, the existing vent system may

not be sized properly to vent the remaining appliances

(For example: water heater). An improperly sized venting

system can result in the formation of condensate, leakage,

or spillage. The existing vent system should be checked

to make sure it is in compliance with NFGC and must be

brought into compliance before installing the furnace.

NOTE: If replacing an existing furnace, it is possible you

will encounter an existing plastic venting system that is

subject to a Consumer Product Safety Commission recall.

The pipes involved in the recall are High Temperature

Plastic Vent (HTPV). 

these pipes  This

recall does not apply to other plastic vent pipes, such

as white PVC or CPVC. Check for details on the CPSC

website or call their toll-free number (800) 758-3688.

Condensate Disposal

The method for disposing of condensate varies according

to local codes. Consult your local code or authority having

jurisdiction.

Each of the condensate drain lines must be J-trapped

using ﬁeld supplied parts. After the condensate lines are

J-trapped, they may be combined together into a single

run to the drain. The drain lines must be routed downward

to ensure proper drainage from furnace.

Neutralizer kit P/N 902377 is available for use with this

furnace. 

the kit.

For Installations where there is limited clearance for the

J-Trap (such as an attic where it may be installed between

ceiling joists), either side of the J-Trap can be shortened

to a minimum of 3 Inches. See Figure 11, (page 16).

• Whentheventpipemustexitanexteriorwallcloseto

the grade or expected snow level where it is not possible

to obtain clearances shown in Figure 7 (page 12), a

riser may be provided as shown in Figure 9. Insulation

is required to prevent freezing of this section of pipe.

See Table 2 (page 13) for vent freezing protection.

Outdoor Terminations - Vertical Venting

Termination spacing requirements from the roof and from

each other are shown in Figure 10. The roof penetration

must be properly ﬂashed and waterproofed with a plumbing

roof boot or equivalent ﬂashing. Vent and combustion air

piping may be installed in an existing chimney which is

not in use provided that:

• Boththeexhaustventandairintakerunthelengthof

the chimney.

• Thetopofthechimneyissealedandweatherproofed.

• The termination clearances shown in

Figure 10 are

maintained.

• Noothergasredorfuel-burningequipmentisvented

through the chimney.

Vent Freezing Protection

CAUTION:



      



be insulated with 1/2 inch thick sponge rubber





icing.

• Table 2 (page 13) lists the maximum length of ﬂue pipe

that can travel through an unconditioned space or an

exterior space. The total vent length must not exceed

the lengths noted in Table 1 (page 10). For Canadian

installations, please refer to the Canadian Installation

Code (CAN/CGA-B149.1) and/or local codes.

• Forextremelycoldclimatesorforconditionsofshort

furnace cycles (i.e. set back thermostat conditions) the

last 18 inches of vent pipe can be reduced. It is acceptable

to reduce from 3” to 2-1/2”, 3” to 2”, or 2” to 1-1/2” if

the total vent length is at least 15 feet in length and the

vent length is within the parameters speciﬁed in Table 1.

The restriction should be counted as 3 equivalent feet.

Smaller vent pipes are less susceptible to freezing, but

must not be excessively restrictive. The length of the 2

inch pipe must not be longer than 18 inches.

• Iffurnaceisinstalledhorizontally,makesurethedrainage

port on the in-line drain assembly is pointed downward

to ensure proper drainage of condensate. See Figure

40 (page 49)

& Figure 41 (page 50).

• To prevent debris or creatures from entering the

combustion system, a protective screen may be installed

over the combustion air intake opening. The screens

hole size must be large enough to prevent air restriction.

WINTER DESIGN

TEMPERATURE

MAXIMUM FLUE PIPE LENGTH (FEET)

IN UNCONDITIONED & EXTERIOR SPACES

WITHOUT INSULATION WITH INSULATION*

20 45 70

0 20 70

-20 10 60

*NOTE: Insulation thickness greater than 3/8 inch, based on an

R value of 3.5 (ft x F x hr) / (BTU x in.)

Table 2. Vent Protection

the coil must be installed downstream (on the outlet

side) of the furnace or in parallel with the furnace.

• If a cooling system is installed in parallel with the

furnace, a damper must be installed to prevent chilled

air from entering the furnace and condensing on the heat

exchanger. If a manually operated damper is installed,

it must be designed so that operation of the furnace is

prevented when the damper is in the cooling position

and operation of the cooling system is prevented when

the damper is in the heating position.

• Itis goodpracticetosealall connectionsandjoints

with industrial grade sealing tape or liquid sealant.

Requirements for sealing ductwork vary from region

to region. Consult with local codes for requirements

speciﬁc to your area.

Return Air Connections

• In applications where the supply ducts carry heated

air to areas outside the space where the furnace is

installed, the return air must be delivered to the furnace

by duct(s) secured to the furnace casing, running full

size and without interruption. 



• Positionthefurnacewiththereturnairductworkensuring

even alignment of furnace (or coil casing) air opening

and return air duct. NOTE: The ductwork must have an

opening equal to that of the return air opening of the

furnace (or coil casing). See Figure 28 (page 31) for

return air opening size.

Upﬂow & Horizontal Furnaces

• The return air ductwork may be connected to the left

side, right side, or bottom of the furnace. NOTE: If

using the left or right side of the furnace for return air,

the bottom panel (Figure 28) must not be removed from

the bottom of the furnace.

WARNING:















• Side Return Installations: To attach the return air duct

to the left or right side of the furnace, punch out the 4

knockouts from the side of the furnace (Figure 28 (page 31)).

Using sharp metal cutters, cut an opening between all

4 knockouts to expose the blower assembly. Position

the return air duct over the opening and secure to the

side with sheet metal screws.

•  If using the bottom of

the furnace for return air, the bottom panel (Figure 28)

must be removed from the bottom of the furnace. See

page 19 for removal instructions. Position the furnace

over the return air duct and secure together with sheet

metal screws. Make sure the screws penetrate the duct

and furnace casing.

CIRCULATING AIR REQUIREMENTS

WARNING:



      

     

     





       







       









       



      











• Plenumsandairductsmustbeinstalledinaccordance

with the Standard for the Installation of Air Conditioning

and Ventilating Systems (NFPA No. 90A) or the

Standard for the Installation of Warm Air Heating and

Air Conditioning Systems (NFPA No. 90B).

• Table 6 (page 32), Table 7 (page 34), & Table 8 (page

35)

contain the maximum airﬂow and temperature

rise data for ﬁxed and variable speed motors. If the

maximum airﬂow is 1,600 CFM or more, it is required

that two openings be used for return air on upﬂow

furnaces. Downﬂow furnaces can only use one return

opening.

• It is recommended that the outlet duct contain a

removable access panel. The opening should be

accessible when the furnace is installed in service and

shall be of a size that smoke or reﬂected light may be

observed inside the casing to indicate the presence of

leaks in the heat exchanger. The cover for the opening

shall be attached in such a way as to prevent leaks.

• Ifoutsideairisusedasreturnairtothefurnacefor

ventilation or to improve indoor air quality, the system

must be designed so that the return air is not less than

60° F (15° C) during operation. If a combination of indoor

and outdoor air is used, the ducts and damper system

must be designed so that the return air supply to the

furnace is equal to the return air supply under normal,

indoor return air applications.

• When a cooling system is installed which uses the

furnace blower to provide airﬂow over the indoor coil,

Downﬂow Furnaces

• Toattachthereturnairducttothedownowfurnace,

bend the ﬂanges on the furnace upward 90° with wide

duct pliers. See Figure 28 (page 31) for furnace ﬂange

locations. NOTE: If system installation includes AC coil

casing, bend the ﬂanges on the coil casing upward 90°

before attaching the return air duct.

• Securethereturnairductworktothefurnaceorcoil

casing (if installed) with sheet metal screws. Make

sure the screws penetrate the sheet metal casing and

ﬂanges.



• The supply air must be delivered to the heated space

by duct(s) secured to the furnace or coil box casing,

running full size and without interruption.

• To attach the supply air duct to upﬂow & horizontal

furnaces, bend the ﬂanges on the furnace upward

90° with wide duct pliers. See Figure 28 (page 31) for

furnace ﬂange locations. NOTE: If system installation

includes AC coil casing, bend the ﬂanges on the coil

casing upward 90° before attaching the supply air duct.

• Position the supply air ductwork onto the furnace

ensuring even alignment of furnace air opening and

supply air duct. NOTE: The ductwork must have an

opening equal to that of the supply air opening of the

furnace. See Figure 28 for supply air opening size.



Damping ducts, ﬂexible vibration isolators, or pleated

media-style ﬁlters on the return air inlet of the furnace

may be used to reduce the transmission of equipment

noise eminating from the furnace. These treatments can

produce a quieter installation, particularly in the heated

space. However, they can increase the pressure drop in

the duct system. Care must be taken to maintain the proper

maximum pressure rise across the furnace, temperature

rise and ﬂow rate. This may mean increasing the duct

size and/or reducing the blower speed. These treatments

must be constructed and installed in accordance with

NFPA and SMACNA construction standards. Consult

with local codes for special requirements. For best sound

performance, be sure to install all the needed gaskets and

grommets around penetrations into the furnace, such as

for electrical wiring

FURNACE INSTALLATION

*TC series gas furnaces offer a wide range of installation

options, including installation in the upﬂow or horizontal

positions with either right, left, or upﬂow return air. The

*TL series gas furnaces may only be installed as a down

ﬂow application.



• Thefurnacemustbeleveledatinstallationandattached

to a properly installed duct system. See Figure 1 (page 6)

for the required clearances needed to move the furnace

to its installation point (hallways, doorways, stairs, etc).

• The furnace must be installed so that all electrical

components are protected from water.

• The furnace must be installed upstream from a

refrigeration system. (If applicable)

• Thecabinetplugmustalwaysbeusedtoclosethehole

in the side of the furnace when rotating the inducer.

• The furnace requires special venting materials and

installation procedures. See page 7, page 8,

page 9, & page 10 for venting guidelines and

speciﬁcations.

Upﬂow Furnaces

WARNING:

       



than wood ﬂooring.

*TC series gas furnaces are shipped with the bottom panel

installed as shown in Figure 28 (page 31). If the furnace

is installed with side return air, the bottom panel must not

be removed. If the furnace is installed with bottom return

air, the bottom panel must be removed. See Bottom Panel

Removal on page 19.

Horizontal Furnaces

WARNING:

       



than wood ﬂooring.

The *TC series gas furnace can be installed horizontally

(Figure 11) in an attic, basement, crawl space or alcove.

It can also be suspended from a ceiling in a basement

or utility room in either a right to left airﬂow or left to right

airﬂow as shown in Figure 12.

*TC series furnaces are shipped with the bottom panel

installed. If furnace is installed horizontally, remove the

bottom panel from the furnace before attaching the duct

system. See Bottom Panel Removal section (page 19).

If installing the furnace with an evaorator coil (in an

attic), it is required that a drip pan be placed under the

furnace. If the installation is on a combustible platform

(Figure 11), it is recommended that the drip pan extend

Downﬂow Furnaces

WARNING:

       



than wood ﬂooring.

WARNING:





To install the furnace on combustible ﬂooring, a special

sub-base is required. Downﬂow sub-base kits are factory

supplied accessories and are listed according to the cabinet

letter of the furnace. For ‘B’, ‘C’, and ‘D’ size cabinets use

Kit #904911. 

with the kit.

A downﬂow sub-base kit is not necessary if the furnace

is installed on a factory or site-built cased air conditioning

coil. However, the plenum attached to the coil casing

must be installed so that its surfaces are at least 1” from

combustible construction.

Installation on a concrete slab

1. Create an opening in the ﬂoor according to the

dimensions in Table 3.

2. Position the plenum and the furnace as shown in

Figure 13.

at least 12 inches past the top and front of the furnace.

NOTE: Although it is not required to use a drip pan for heat

only applications, state and local codes may require it.

If the furnace will be suspended from the ceiling, assemble

a support frame (

Figure 12) using slotted iron channel and

full threaded rod. Fasten the frame together with nuts,

washers, and lockwashers. Secure the support frame to

the rafters with lag bolts.

NOTE: The furnace can also be suspended using steel

straps around each end of the furnace. The straps should

be attached to the furnace with sheet metal screws and

to the rafters with bolts.

It is recommended for further reduction of ﬁre hazard

that cement board or sheet metal be placed between the

furnace and the combustible ﬂoor and extend 12 inches

beyond the front of the door and top of the furnace.

Figure 12. 

Lag

Bolt

Nuts (x2)

Washer

and

Lockwasher

Nuts (x2)

Threaded

Rod

Figure 13. Furnace on a Concrete Slab

Concrete

Floor

Furnace

Sheet

Metal

Plenum

Flue pipe vented

to outside

J-Trap

Height

3” Min.

Coil Plenum

Wood or

non-combustible

platform

Combustion Air

Condensate

Drain Lines

Figure 11. 

Table 3. 

CABINET SIZE DIM. “A” DIM. “B”

B 16 5/8 19 1/4

C 20 1/8 19 1/4

D 23 5/8 19 1/4

NOTE: Dimensions shown in Inches.

“A”

“B”

Opening in concrete floor

Inducer & Venting Options

To increase installation ﬂexibility, the inducer assembly

can be rotated to 2 different positions    

. Each variation has slightly different

requirements with regard to condensate disposal and, in

some cases, the need to seal the furnace cabinet.

IMPORTANT NOTES

 



 



Before using Table 4, the number of pipes (1-pipe or 2-pipe)

connected to the furnace must be known. Find the proper

furnace style (upﬂow, horizontal, or downﬂow) and then

the side that the pipes will exit from the furnace. Finally

select the option that properly matches your installation

type from Figure 38 (page 47), Figure 39 (page 48) Figure

40 (page 49), Figure 41 (page 50)

& Figure 42 (page 51).

NOTE: It is important that Direct Vent (2-pipe) systems

maintain an airtight ﬂow path from the air inlet to the ﬂue

gas outlet. The furnace ships from the factory with two

holes in the cabinet for the air inlet and ﬂue gas outlet.

In certain conﬁgurations, it is necessary to remove and

relocate a plastic cap in the furnace cabinet. If changing

the position of the air inlet and ﬂue gas outlet, it is required

that the previous hole be closed off with the plastic cap to

maintain air tightness in the furnace. The hole locations

for *TC & *TL furnaces are shown in Figure 28 (page 31).

Inducer Assembly Rotation

WARNING:

     





     



CAUTION:

It is good practice to label all wires prior to



and dangerous operation.

1. Disconnect the electrical harness from the inducer

assembly.

2. Remove the inducer assembly ground wire from the

blower deck or door.

3. Upﬂow Furnaces: Remove 4 screws securing the inducer

assembly to the header box.

Downﬂow Furnaces: Remove 3 screws securing the

inducer assembly to the header box.

4. Remove drain tube from inline drain assembly.

5. Rotate the inducer assembly to its new position.

6. Secure the inducer assembly to the header box by

reinstalling the four screws. NOTE: An extra screw is

provided in the parts package with downﬂow furnaces.

7. Remove the cabinet plug from side of furnace and

reinstall in hole on opposite side of cabinet.

8. Connect all condensate drains as required for your

installation. See Table 4 (page 17) and Figure 38 (page

47)

, Figure 39 (page 48) Figure 40 (page 49), Figure

41 (page 50)

& Figure 42 (page 51).

9. Reconnect the electrical harness to the inducer

assembly.

10. Reconnect the inducer assembly ground wire to the

blower deck or door.

11. Verify proper operation as detailed on the furnace label.

Pressure Switch Tubing

Figure 14 displays the proper routing of pressure switch

tubing for *TC furnaces. All upﬂow / horizontal furnaces

have two pairs of switches. One set is connected to the

static tap on the inducer assembly and the other to the

collector box. Downﬂow (*TL) furnaces require only one

pair of switches to be connected to the inducer’s static

tap. See Figure 15.

Accessories

The components in Figure 16 (page 18) & Figure 17

(page 19)

are included in the extra parts bag supplied

with the purchase of *TC / *TL furnaces. Depending on

your particular installation, some of these components

are optional and may not be used. Please refer to the

descriptions and accompanying ﬁgures when installing

these items.

‘A’ WIDTH CABINETS

VENT UPFLOW

HORIZ.

RIGHT

HORIZ.

LEFT

DOWN

FLOW

1-PIPE

OPTIONS

Right N/A

Option 7

N/A N/A

Option 1

N/A N/A N/A

Left N/A N/A

Option 8

N/A

2-PIPE

OPTIONS

Right N/A

Option 9

N/A N/A

Option 2

N/A N/A N/A

Left N/A N/A

Option 10

N/A



VENT UPFLOW

HORIZ.

RIGHT

HORIZ.

LEFT

DOWN

FLOW

1-PIPE

OPTIONS

Right

Option 3

N/A N/A

Option 15

Up N/A

Option 11 Option 12 Option 16

Left

Option 4

N/A N/A

Option 17

2-PIPE

OPTIONS

Right

Option 5

N/A N/A

Option 18

Up N/A

Option 13 Option 14 Option 19

Left

Option 6

N/A N/A

Option 20

Table 4. Vent & Inducer Blower Options

Finish Flange

The ﬁnish ﬂange must be installed to vent the combustion

air pipe through the top of the furnace. NOTE: For proper

installation it is important that the pipe and screw holes in

the ﬁnish ﬂange, gasket, and cabinet are aligned.

1. Position ﬂange gasket over hole in the furnace cabinet.

2. Position ﬁnish ﬂange on top of the ﬂange gasket.

NOTE: Make sure the ﬂange is properly oriented so

that the FRONT lettering is located near the front of

the furnace as shown in Figure 16.

3. Secure ﬂange and gasket to cabinet with three ﬁeld

supplied sheet metal screws.

Rubber Grommets

The 2 1/4” rubber grommet is used to seal the opening

between the furnace cabinet and the 2” PVC vent pipe.

The rubber grommet should be installed in the 3” hole

prior to running the vent pipe out of cabinet. No sealants

are required. See Figure 16.

The 7/8” rubber grommet is used to seal the opening

between the furnace cabinet and the gas pipe. The rubber

grommet should be installed in the 1 5/8” hole prior to

running the gas pipe into the cabinet. No sealants are

required.

AIRFLOW

123

567

Figure 14. 

*TC Upﬂow / Horizontal Furnaces



AIRFLOW

123

567

Figure 15. Pressure Switch Tubing



Figure 16. 

Ø 3/4” Rubber

Grommet

ø 2 1/4” Rubber

Grommet

ø 7/8” Rubber

Grommet

Inlet Air

Finish Flange

Flange

Gasket

FRONT

FRONT lettering must be

located near front

of furnace

PVC Components

IMPORTANT NOTES:

 





 Figure 17

in the extra parts bag.

 





The 2” PVC Tee and Trap are used when the inducer is

rotated to vent out thru the left or right side of the furnace

cabinet. See Figure 17.

The 1/2” x 3/4” hose barb can be used to route the

condensate drain to the outside of the cabinet. It must

be installed from inside the cabinet with the threaded

end inserted thru the 1 1/16” hole. See Figure 28 (page

31)

for hole location The condensate drain should be

connected to the barbed end. Attach 1” PVC drain line

to the threaded end.

Typical Orientation

1. Install the PVC Tee vertically on the 2” vent pipe that is

extending out the side of the cabinet. Permanently bond

them together using appropriate primer and cement.

Refer to the typical orientation shown in Figure 17.

2. Install the reducer or PVC trap (if supplied) on the bottom

end of the PVC Tee. Permanently bond them together

using appropriate primer and cement.

3. Install the 1/2” x 1/2” hose barb on the 2” PVC reducer.

NOTE: Do not over tighten! Use an adequate amount of

Teﬂon tape on the threads. Do not use liquid sealants.

4. Verify all connections and joints for tight ﬁt and proper

alignment with other vent pipes.

The 3/4” rubber grommet is used if venting out the left

side of the cabinet and the drain tube is routed through

the blower deck. Remove the plastic plug from the hole

and install the grommet before routing the drain tube.

Alternate Orientation

1. Install the 2” PVC Tee horizontally on the 2” vent pipe that

is extending out the side of the cabinet. Permanently bond

them together using appropriate primer and cement.

Refer to the alternate orientation shown in Figure 17.

2. Install the 2” PVC Elbow on the end of the 2” PVC Tee.

Permanently bond them together using appropriate

primer and cement.

3. Install the reducer or PVC trap (if supplied) on the bottom

end of the PVC Tee. Permanently bond them together

using appropriate primer and cement.

4. Install the 1/2” x 1/2” hose barb on the 2” PVC reducer.

NOTE: Do not over tighten! Use an adequate amount of

Teﬂon tape on the threads. Do not use liquid sealants.

5. Verify all connections and joints for tight ﬁt and proper

alignment with other vent pipes

Condensate Drain Lines

IMPORTANT NOTE

















The placement of the condensate drain lines will depend

on the conﬁguration selected in Table 4, (page 17). The

drain lines can be routed out the left or right side of the

furnace, but must maintain a downward slope to ensure

proper condensate drainage.

The J-trap may need to be rotated to the side that matches

your setup in Figure 38 (page 47), Figure 39 (page 48)

Figure 40 (page 49), Figure 41 (page 50) & Figure 42

(page 51)

. To rotate the J-trap, loosen the clamp on the

drain tube, rotate the J-trap to either side, and retighten

the clamp.

THREE GENERAL RULES APPLY:

• Eachcondensatedrainlinemustbeseparatelytrapped

using a J-Trap or ﬁeld supplied loop. After individually

trapping the condensate lines, it is acceptable to combine

the drains.

• Theremustalwaysbeadrainattachedtothecollector

at the outlet of the secondary heat exchanger.

• Theremustalwaysbeadrainatthelowestpointofthe

venting system. NOTE: If using a condensate pump, the

furnace drain line must be installed above the pumps

water line.

EXCEPTIONS AND CLARIFICATIONS TO THE

GENERAL RULES:

• Insomecases,thelowestpointintheventsystemis

where it connects to the inducer (Option 12 & Option 14).

In this case one drain at this location is sufﬁcient.

• Iftheventexitsthefurnacehorizontally,theventmay

be turned vertically with a tee. 

 (Option 3, Option 4, Option

, Option 6, Option 15, Option 17, Option 18, Option 20).

• In certain cases, it is permitted to drain the inducer

back into the top drain of the collector (Option 3, Option

, Option 11, Option 13, Option 15, Option 16, Option 18, &

Option 19). To ensure proper drainage of condensate,

make sure the drain line does not sag or becomes

twisted. The drain tube supplied with the furnace may

need to be trimmed.



The steps listed below describe how to remove the bottom

panel from the furnace. See Figure 18.

1. Remove the door (1) from the blower compartment.

2. Disconnect the blower motor wiring harness (2) from

the control board.

3. Remove two screws (3) securing the blower assembly

(4) to the furnace.

4. Carefully pull the blower assembly (4) out thru the front

of the furnace.

1/2” x 3/4”

Hose Barb

2” PVC Elbow

(Field Supplied)

2” PVC Tee

1/2” x 3/4”

Hose Barb

2” PVC Pipe from Inline

Drain Assembly

(Not Included)

PVC

Trap

INSTALLATION OF PVC COMPONENTS

(TYPICAL ORIENTATION)

INSTALLATION OF PVC COMPONENTS

(ALTERNATE ORIENTATION)

2” PVC Tee

2” PVC Pipe from Inline

Drain Assembly

(Not Included)

PVC

Trap

1/2” Tubing (Field Supplied

)

Drain Line Attached

to PVC Trap

(Do Not Trap)

1/2” Tubing (Field Supplied)

Drain Line Attached

to PVC Trap

(Do Not Trap)

Figure 17. 

5. Remove all screws (5) securing bottom panel (6) to

bottom of furnace and front brace (7).

6. Lift up and slide bottom panel (6) out through front of

furnace.

7. Reinstall the blower assembly (4) in reverse order.

Figure 18. 

Figure 19. 

GAS SUPPLY & PIPING

WARNING:

FIRE OR EXPLOSION HAZARD

 



 



gas supplier.

        





WHAT TO DO IF YOU SMELL GAS

 

 



 

       

neighbor’s phone. Follow the gas supplier’s

instructions.

 



 







(ANSI Z223.1) or (CAN/CGA B149.1) Installation

Codes.

 







        





Figure 20 (page 21).

 



 

       



 





 





be used. Do not reuse old ﬂexible gas connectors.

 

run to the unit. See

Figure 20.

Table 10 (page 36) lists gas ﬂow capacities for standard

pipe sizes as a function of length in typical applications

based on nominal pressure drop in the line.

Alternate Bottom Panel Removal

If the bottom panel cannot be removed using the previous

instructions, the steps below are an alternate method for

removing the bottom panel. See Figure 19.

1. Remove the door (1) from the blower compartment

2. Remove all screws securing the bottom panel (2) to the

front brace (3).

3. Remove two screws (4) securing the furnace cabinet

to the blower deck (5).

4. Remove all screws (6) securing the furnace cabinet to

the bottom panel (2).

5. Remove the screw (7) securing the bottom corner of

the furnace cabinet to the front brace (3).

6. Carefully spread the bottom corner of the furnace cabinet

outwards while sliding the bottom panel (2) out through

the front of the furnace.

7. Reassemble the furnace in reverse order.

La page charge ...

Kelvinator KG7T(C,L) Guide d'installation

Marque: Kelvinator

Modèle: KG7T(C,L)

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Kelvinator KG7T(C,L) Installation guide

Kelvinator KG7T(C,L) Guide d'installation

Ce manuel convient également à

Kelvinator KG7T(C,L) Guide d'installation

dans d''autres langues

Documents connexes

Autres documents