KitchenAid KRFC804GBS Guide d'installation

W10913649B

DOOR-WITHIN-DOOR FRENCH DOOR REFRIGERATOR

Use and Care Guide

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES TWO OR MORE PEOPLE.

RÉFRIGÉRATEUR À DOUBLE BATTANT

AVEC PORTE DOUBLE

Guide d’utilisation et d’entretien

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L’INSTALLATION NÉCESSITE

L’INTERVENTION DE DEUX PERSONNES OU PLUS.

REFRIGERADOR DE PUERTAS FRANCESAS DOBLE PUERTA

Manual del usuario

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. SE REQUIEREN DOS O MÁS PERSONAS

PARA REALIZAR LA INSTALACIÓN.

Table of Contents/Table des matières/Índice..................................................................2

2

TABLE OF CONTENTS/TABLE DES MATIÈRES/ÍNDICE

REFRIGERATOR SAFETY ....................... 3

PARTS AND FEATURES .......................... 4

What’s New Behind the Doors? ............. 5

GETTING STARTED ................................. 6

REFRIGERATOR CONNECTIVITY

FEATURES ................................................ 8

INSTALLATION INSTRUCTIONS ............ 9

Unpack the Refrigerator ......................... 9

Location Requirements .......................... 9

Remove and Replace Refrigerator

Doors .................................................... 10

Remove and Replace

Freezer Drawer Fronts .......................... 13

Electrical Requirements ....................... 14

Water Supply Requirements ................ 14

Connect the Water Supply ................... 14

Handle Installation and Removal ......... 15

Refrigerator Leveling

and Door Closing ................................. 17

FILTERS AND ACCESSORIES ............. 18

Water Filtration System ........................ 18

Install Air Filter ...................................... 19

Install Produce Preserver ..................... 19

Accessories .......................................... 20

REFRIGERATOR USE ............................ 20

Opening and Closing Doors ................. 20

Using the Controls ............................... 21

External Dispenser Controls ................ 22

Lighting the Refrigerator ...................... 23

Water and Ice Dispensers .................... 23

Ice Maker and Storage Bin ................. 26

Shelves, Bins, and Drawers ................. 27

Freezer Drawers ................................... 30

Audio Reference ................................... 30

REFRIGERATOR CARE ......................... 31

Cleaning ............................................... 31

Lights .................................................... 32

Vacation and Moving Care ................... 32

TROUBLESHOOTING ............................ 33

PERFORMANCE DATA SHEET............. 40

WARRANTY ............................................ 41

SÉCURITÉ DU RÉFRIGÉRATEUR ........ 42

PIÈCES ET CARACTÉRISTIQUES ........ 43

Quoi de neuf en coulisse? ................... 44

MISE EN PLACE ......................................45

FONCTIONS DE CONNECTIVITÉ

DU RÉFRIGÉRATEUR ............................. 47

INSTRUCTIONS D’INSTALLATION .......48

Déballage du réfrigérateur ................... 48

Exigences d’emplacement ................... 48

Retrait et réinstallation des portes

du réfrigérateur ..................................... 49

Retrait et réinstallation de l’avant

du tiroir de congélation ........................ 52

Spéciﬁcations électriques .................... 53

Spéciﬁcations de l’alimentation

en eau ................................................... 53

Raccordement à la canalisation

d’eau ..................................................... 53

Installation et retrait des poignées ....... 54

Nivellement du réfrigérateur

et fermeture de la porte ........................ 56

FILTRES ET ACCESSOIRES ................ 57

Système de ﬁltration d’eau .................. 57

Installation du ﬁltre à air ....................... 58

Installation du conservateur de

produits frais ......................................... 59

Accessoires .......................................... 59

UTILISATION DU RÉFRIGÉRATEUR .... 60

Ouverture et fermeture des portes ....... 60

Utilisation des commandes ................. 61

Commandes de distributeur externe ... 63

Éclairage du réfrigérateur ..................... 63

Distributeurs d’eau et de glaçons ........ 63

Machine à glaçons et bac

d’entreposage ..................................... 66

Tablettes, balconnets et tiroirs ............. 68

Tiroirs du congélateur .......................... 71

Référence audio ................................... 71

ENTRETIEN DU RÉFRIGÉRATEUR ...... 72

Nettoyage ............................................. 72

Lampes ................................................. 73

Précautions à prendre pour les

vacances ou le déménagement ........... 73

DÉPANNAGE .......................................... 74

FICHE DE DONNÉES RELATIVES AU

RENDEMENT .......................................... 82

GARANTIE ............................................... 83

SEGURIDAD DEL REFRIGERADOR ..... 85

PIEZAS Y CARACTERÍSTICAS ............. 86

¿Qué hay de nuevo detrás de

las puertas? .......................................... 87

PARA COMENZAR .................................. 88

CARACTERÍSTICAS DE CONECTIVIDAD

DEL REFRIGERADOR ............................. 90

INSTRUCCIONES DE INSTALACIÓN ... 91

Desembale el refrigerador .................... 91

Requisitos de ubicación ....................... 91

Cómo retirar y volver a colocar

las puertas del refrigerador .................. 92

Cómo retirar y volver a colocar el

frente de los cajones del congelador ... 95

Requisitos eléctricos ............................ 96

Requisitos de suministro de agua ....... 96

Conexión del suministro de agua ........ 96

Cómo instalar y quitar las manijas ....... 98

Nivelación del refrigerador

y cierre de las puertas .......................... 99

FILTROS Y ACCESORIOS .................. 100

Sistema de ﬁltración de agua ............ 100

Instalación del ﬁltro de aire ................ 102

Instale el preservador de alimentos

frescos ................................................ 102

Accesorios .......................................... 103

USO DEL REFRIGERADOR ................. 103

Cómo abrir y cerrar las puertas ......... 103

Uso de los controles .......................... 104

Controles del despachador externo .. 106

Iluminación del refrigerador ............... 106

Despachadores de agua y de hielo ... 106

Fábrica de hielo y depósito ............... 110

Estantes, depósitos y cajones ........... 111

Cajones del congelador ..................... 113

Referencia de audio ........................... 113

CUIDADO DEL REFRIGERADOR ....... 114

Limpieza ............................................. 114

Luces .................................................. 115

Cuidado durante las vacaciones

y las mudanzas .................................. 115

SOLUCIÓN DE PROBLEMAS.............. 116

HOJA DE DATOS DE RENDIMIENTO 123

GARANTÍA............................................. 124

3

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

REFRIGERATOR SAFETY

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use nonflammable cleaner.

■ Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ Use a sturdy glass when dispensing ice (on some models).

■ Do not hit the refrigerator glass doors (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

4

PARTS AND FEATURES

Air filter

Water filter

FreshSeal™

crispers

Temperature-

controlled

pantry drawer

Self-close

pull-out tray

In-Door-Ice®

ice storage

Slide-away split

shelf

Removable

bins

Under-shelf

prep zone

FreshSeal™

Herb

storage

bin

Proper Disposal of

Your Old Refrigerator

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are

still dangerous—even if they will sit for “just a few days.” If

you are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children may not easily

climb inside.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

Temperature

control UI

FreshVue™ Door-within-Door

Full Gallon

Storage pull-out

bins

5

Your KitchenAid® Door-Within-Door French Door Refrigerator comes equipped

with various innovative storage and energy-efcient features.

FreshVue™ Door-within-Door

Provides a tinted exterior storage door with four bins and a

window that lights up as you approach it. The proximity lighting

provides visibility, while the door allows easy access to frequently

used ingredients without opening the main refrigerator.

Auto Light Interior LED Lighting

Rows of bright LED mounted lights slowly illuminate as you

approach and gradually turn off when you walk away making it

easy to nd ingredients inside your refrigerator without opening

the door.

Under-Shelf Prep Zone

A slide-out pan utilizes empty space beneath the shelf to create a

prep zone ideal for dough, desserts, or marinating meats. Slide-

out pan is oven- and dishwasher-safe, and easily transitions from

fridge to oven so you can stay in the creative ow.

Slide-Away Split Shelf

This shelf features a versatile design that allows three-quarters

of the shelf to retract to accommodate taller items, up to 16¾"

(42.5 cm). This exibility helps maximize storage space and

optimize organization.

FreshSeal™ Crispers

These upgraded crisper drawers use a gasket seal to maintain

the ideal temperature and humidity levels to keep produce fresh

longer. These drawers also feature premium soft-close glides

that provide the best extension for easy access and maximum

visibility to your produce items.

Full-Extension Self-Close Custom Temperature-

Controlled Pantry Drawer

Four temperature presets are available on the interior control to

keep items at the optimal temperature. You can choose from

meat/sh, cold drinks, deli/cheese, and wine. Pantry drawer

slides open effortlessly, even when fully loaded, with soft, self-

close glides, and features the best extension in freestanding

refrigeration.

Full-Extension Self-Close Pull Out Tray

The tray fully extends for easy access and visibility. The tray also

features soft self-close glides that provide effortless movement,

even when fully loaded. The tray is removable, making cleaning

easy.

Preserva® Food Care System with Linear Compressor

Provides the height of food preservation with two independent

cooling systems plus a Produce Preserver to help keep food at

its peak. The Linear Compressor’s efcient cooling system offers

minimal temperature variation, which makes this is our quietest

freestanding French door refrigerator.

Produce Preserver

Ethylene is a natural gas produced by fruits and vegetables to

promote ripening. The Produce Preserver absorbs ethylene to

delay the over-ripening of fresh produce. As a result, certain

produce items will stay fresh longer.

3-Tier Self-Close Freezer Drawer with Extend-Freeze™

Setting or 3-Tier Self-Close Freezer Drawer with Ice

Maker (depending on models)

A drawer system that organizes items on three levels making

them easier to store and nd. The lower drawer includes a

divider. There’s also an in-door pizza pocket, a pull-out drawer for

smaller items and third level glass shelf for small, at items.

The Extend-Freeze™ setting takes the entire freezer to its coldest

setting to help reduce freezer burn and extend the life of frozen

items.

In-Door-Ice® Ice Dispensing System

The ice maker and ice storage bin are located in the door for easy

access to ltered ice while freeing up valuable shelf space inside.

Panoramic LED Lighting

Increased visibility to your ingredients with strips of lighting on

the sides, ceiling, and back of the refrigerator, as well as in the

crisper and pantry. LED lights are maintenance-free and do not

require replacement.

PrintShield™ Finish

Resists smudges and ngerprints. The specialized coating for

stainless steel is easy to clean with just water and a soft cloth.

Wi-Fi Connectivity

This refrigerator can connect with in-home Wi-Fi to provide

remote control through app, available to download for use with

either iOS or Android devices.

Water Dispenser with Measured Fill

The Measured Fill feature allows you to dispense a desired

amount of ltered water in handy increments of 8, 16, or 24 oz.

Water Dispenser with Favorite Fill

The Favorite Fill feature allows you to save two custom presets

that can be programmed for favorite items that are frequently

lled like a coffee pot or a water bottle.

FreshSeal™ Herb Storage Bin

This is a cylinder with FreshSeal™ to keep sensitive items like

herbs fresh longer. The container allows water to be added

to keep stems wet without covering leaves. It can be placed

anywhere in the refrigerator and accommodates tall items like

parsley, cilantro, and rosemary in addition to herbs like oregano,

thyme, and mint.

Adjustable Shelves on Flipper System

Shelves that can be adjusted up or down easily with the ip of

a lever, allowing them to be adjusted without having to unload

them. The shelves are easy to clean and let you use the whole

shelf edge to edge for full visibility and accessibility.

FreshSeal™ Dairy Bin

A dedicated dairy bin with the FreshSeal™ gasket to help extend

the freshness and preserve the avor of butter and other dairy

items.

What’s New Behind the Doors?

6

GETTING STARTED

INSTALLATION CHECKLIST

✔ Electrical Power

Plug refrigerator into a grounded 3 prong outlet.

✔ Doors

If doors need to be removed during installation, see the

“Remove and Replace Doors” section in the instructions.

Check that handles are secure and installed according to the

instructions.

Doors seal completely.

Refrigerator is level. (Remove base grille and adjust leveling

feet so they are snug against the oor.)

Doors are even across the top. (Use door alignment feature

if necessary.)

Base grille is properly attached to the refrigerator.

✔ Ice and Water System (on some models)

Connect refrigerator to a cold water supply with

20-120 psi (1.4-8.4 Kg/cm) water pressure, as specied in the

instructions.

Make sure the household water supply is connected and

turned on.

Check that the water supply line behind refrigerator is not

kinked.

Only use recommended water supply tubing, copper, or PEX,

as specied in the instructions.

Install water lter according to the instructions.

Flush water system with 3 gallons (11.4 L) of water, as

specied in the instructions.

Check for water leaks at all connections.

Turn on ice maker if refrigerator is connected to water supply.

(If not connected to water supply, turn off ice maker.)

✔ Final Checks

Install air lter and Produce Preserver according to

instructions in corresponding packaging.

Remove all shipping material.

Set temperature controls to the recommended setting.

Save instructions and other literature.

Send in registration card or register your product online.

WATER FILTER INSTALLATION

Locate the water lter compartment in the lower left-hand side

of the refrigerator compartment. Push on the right side of the

lter door to open.

Align the arrow on the water lter cap with the cutout notch in

the lter housing and insert lter.

Once the lter is inserted, turn the lter clockwise 90°

(1/4 turn) until it locks into the housing.

Push water lter door closed to latch.

Flush 3 gallons (11.4 L) of water through the water system to

clear air from the water line and to keep the dispenser from

dripping and/or avoiding decreased dispenser ow.

NOTE: If the lter is not installed correctly, water may

dispense at a lower ow rate and there will be slower ice

production. Improper lter installation may also cause the

water lter housing to leak.

To view videos on door removal/

replacement, door adjustment, water

filter installation, air filter installation,

shelf adjustment or removal, and Wi-Fi

connectivity (if applicable), scan the code

to the left with your mobile device.

Air Filter

An air lter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator. Replace

your air lter every 6 months for maximum odor reduction.

EveryDrop™ Water Filter

EveryDrop™ water lters are NSF®† Certied to reduce most

contaminants, including chlorine taste and odor, lead, pesticides,

and trace amounts of pharmaceuticals. EveryDrop™ brand

lters are the only lters tested and certied for your refrigerator

system. Replace your EveryDrop™ lter every 6 months for

maximum contaminant reduction.

Removable Door Bins

Door bins that can be easily removed from the metal nish base

they sit on, making them ideal for carrying condiments or items

from refrigerator to table. The bins are dishwasher-safe for easy

cleaning.

Power Outage Indicator

If the power should go out while you are away from home, this

indicator will let you know that the refrigerator has been without

power.

†®NSF is a registered trademark of NSF International.

7

ENERGY SAVER MODE AND NORMAL

OPERATING SOUNDS

Your new Door-Within-Door French Door Refrigerator has been

designed to optimize energy efciency and better regulate

temperatures to match cooling demand.

You may notice that it operates differently from your previously

owned refrigerator.

It is normal for the high-efciency compressor to run for extended

periods of time at varying speeds in order to consume only the

energy necessary for optimum efciency.

In addition, during various stages of the cooling cycle, you may

hear normal operating sounds that are unfamiliar to you.

Energy Saver Mode

Turns off the anti-sweat heaters to save the customer power.

When the icon is bright, the function is activated (heaters off);

icon off means that it is inactive (heaters on). The user can toggle

the feature by pressing the button. If the user lives in a climate

with high humidity, Energy Saver mode is not recommended.

DOOR ALIGNMENT

Align Refrigerator Doors

✔ If doors are uneven:

Ensure the refrigerator is level.

Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand

refrigerator door. The alignment screw is inside the bottom

hinge pin.

 Insert the short end of the 1/8" (3.18 mm) hex key wrench

(packed with the Door Handle Installation Instructions) into

the bottom hinge pin until it is fully engaged in the alignment

screw.

To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

 Continue to turn the alignment screw until the tops of the

doors are aligned.

A

B

Shelf Height Adjustment

Shelf height can be adjusted by changing the adjustable shelf

mounts between their vertical and horizontal positions.

Carefully lift the shelf off the shelf mounts and turn the ipper

to the desired orientation.

Repeat for remaining shelf mounts.

Ensure the shelf is properly seated on the shelf mounts.

A. Bottom hinge pin

B. 1/8" (3.18 mm) hex key wrench

8

REFRIGERATOR CONNECTIVITY FEATURES (ON SOME MODELS)

Wi-Fi connectivity allows your Smart Refrigerator to connect to the Internet and interact with the KitchenAid™ App from your

smartphone or mobile device. Check any connection instructions for your specic router, and refer to alternate instructions at

www.kitchenaid.com/connect or call 1-877-559-2603.

NOTE: KitchenAid™ App features and functions are subject to change.

SMART FEATURES

Smart Features help make your everyday a little more efficient

by letting you remotely monitor, manage, and maintain your

refrigerator.

Remote Temperature Control

What it does: Allows you to control the temperature of

your refrigerator remotely from your mobile device via the

KitchenAid™ App.

What it does for you: Lets you control temperatures in your

refrigerator, freezer, and temp-controlled pantry remotely—not

just when you are standing in front of it.

Water and Air Filter Status

What it does: Gives you a look at the life remaining for your air

and water lters before replacement is needed.

What it does for you: Helps you be more efcient in planning

for ordering and replacing lters.

Door Open Alert

What it does: Sends you a notication when one of the doors

of the refrigerator has been left open.

What it does for you: Alerts you to Door Ajar status so you can

close the door(s) or call home to ask someone else to close the

door before an over-temp situation arises.

Power Outage

What it does: Sends you a notication when power to your

refrigerator goes out, returns, or highest temperature is reached

in the refrigerator and freezer compartments.

What it does for you: Alerts you to power status and duration

of outage to provide input regarding disposition of refrigerator/

freezer contents.

Max Ice/Max Cool Control

What it does: Allows you to control your refrigerator remotely

from your mobile device via the KitchenAid™ App.

What it does for you: Lets you turn on/off Mac Ice and Max

Cool options remotely to increase ice production or make

temperatures colder in refrigerator and freezer in anticipation

of loading in newly purchased grocery items.

GET STARTED

Go to www.kitchenaid.com/connect and follow the instructions

to get connected.

Check the KitchenAid™ App frequently for additional information

and features.

Requires Wi-Fi and account creation. KitchenAid™ App features

and functionality subject to change. Subject to Terms of Service

available at: www.kitchenaid.com/connect. Data rates

may apply.

9

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

■Remove tape and glue residue from surfaces before turning

on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your ngers. Wipe with warm water

and dry.

■Do not use sharp instruments, rubbing alcohol, ammable

uids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator.

■Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your refrigerator before using it. See the cleaning instructions

in the “Refrigerator Care” section.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

Location Requirements

IMPORTANT: This refrigerator is designed for indoor, household

use only.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) space on each side and at the top. Allow for a

1" (2.54 cm) space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a xed wall,

leave a 3 3/4" (9.5 cm) minimum space between the refrigerator

and wall to allow the door to swing open.

NOTE: This refrigerator is intended for use in a location where

the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity usage

and provides superior cooling, is between 60°F (15°C) and 90°F

(32°C). It is recommended that you do not install the refrigerator

near a heat source, such as an oven or radiator.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

3 3/4" (9.5 cm)

1/2" (1.25 cm)

Refrigerator Delivery

■A minimum door opening of 33" (838 mm) is required. If

door opening is 36" (914 mm) or less, then removal of doors,

drawer, and hinges is required.

■Cart the refrigerator from the side for all door openings.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the oor with

cardboard or hardboard to avoid oor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or

“walk” the refrigerator when trying to move it, as oor

damage could occur.

10

Remove and Replace Refrigerator Doors

NOTE: Measure the width of your door opening to see whether or not you need to remove the refrigerator doors to move the

refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT: If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the refrigerator

control off. Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.

TOOLS NEEDED: TORX® T25®† screwdriver and a #2 Phillips screwdriver

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Water Dispenser

Tubing Connection

Wiring Plug

Top Right Hinge

Top Left Hinge

A

A. Outer ring

C

B

A

A. TORX® T25® screws

B. Ground wire (Do not remove.)

C. Do not remove screws.

90°

Door at 90° Angle

to Cabinet°

A. TORX® T25® screws

B. Hinge cover screw

C. Top hinge cover

D. Top hinge

A

B

C

D

†®TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.

11

Bottom Door Hinge

For your convenience, the refrigerator doors have bottom hinges

with door closers. These closers allow the doors to swing fully

closed with just a gentle push.

IMPORTANT: So that the closers feature will operate properly,

the doors must be removed only when open to a 90° angle to the

front of the cabinet. If one or both doors were not at a 90° angle

when removed, the bottom door hinge must be reset.

90°

Reset the Door Hinge

1. Lift the door from the bottom hinge pin and place it on a at

surface.

2. Using a TORX® T25® screwdriver, remove the bottom hinge

with the bushing from the cabinet.

A. Bushing

B. Hinge base

3. Insert the bottom hinge and bushing into the corresponding

slot in the bottom of the door.

NOTE: Make sure that the base of the hinge is parallel to the

bottom of the door.

A. Hinge base parallel to the bottom edge of the door

4. Turn the hinge until the hinge base is at a 90° angle to the

bottom edge of the door.

A. Hinge base turned to a 90° angle with the bottom edge of the door

5. Remove the hinge from the door. Using a driver with a #2

square bit, reattach the bottom hinge to the refrigerator

cabinet.

6. The hinge is now reset and prepared for the door to be

replaced. See “Replace Refrigerator Doors” later in

this section.

A

B

A

90°

A

Remove Refrigerator Doors

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so can result in death or electrical shock.

Remove Right-Hand Door

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift

them free from the cabinet.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

3. Using a Phillips screwdriver, remove the cover from the top

hinge.

4. Using the TORX® T25® screwdriver, remove the three screws

from the top hinge and set aside.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

12

A. Top hinge cover screw

B. Top hinge cover

C. TORX® T25® screws

D. Top hinge

WARNING

Excessive Weight Hazard

Use two or more people to lift the refrigerator door.

Failure to do so can result in back or other injury.

5. Open the door until it is at a 90° angle to the front of the

cabinet.

6. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

Remove Left-Hand Door

IMPORTANT: The tubing and wiring for the water dispenser run

through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top

hinge.

A. Top hinge cover screw B. Top hinge cover

2. Disconnect the water dispenser tubing located on top of the

door hinge. Firmly pull up on the clasp. Then, pull the tubing

out of the fitting.

NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

3. Disconnect the wiring plug located on top of the door hinge.

■Grasp each side of the wiring plug. With your left thumb,

press down to release the catch and pull the sections of

the plug apart.

NOTE: Do not remove the green ground wire. It should

remain attached to the door hinge.

A. TORX® T25® screws

B. Ground wire (Do not remove.)

4. Using the TORX® T25® screwdriver, remove the three internal

screws from the top hinge and set aside.

NOTE: Provide additional support for the refrigerator door

while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are

working.

A

B

5. Lift the refrigerator door from the bottom hinge pin. The top

hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges

and brake feet assemblies to move the refrigerator through a

doorway.

■Only if necessary, use a TORX® T25® screwdriver to

remove the bottom hinges and brake feet screws.

A

B

A

B

C

D

13

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the

refrigerator door.

3. Using the three TORX® T25® screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring

bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the three TORX® T25® screws, fasten the hinge to the

cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing.

Insert the tubing rmly into the tting until it stops. Close the

clasp around the tubing. The clasp snaps into place between

the tting and the collar. Connect blue female side with blue

male side and clasp. Repeat with gray female and gray male

side.

4. Reconnect the electrical wiring.

■Push together the two sections of the wiring plug.

Final Steps

1. Completely tighten the ve internal TORX® T25® screws (three

on the right-hand door hinge and two on the left-hand door

hinge).

2. Replace both top hinge covers.

Remove and Replace

Freezer Drawer Fronts

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to

the drawer glides. The two screws (one on the left-hand side

and one on the right-hand side) are located inside the drawer

front.

3. Remove the two screws at the bottom, inside the drawer front

that fasten the drawer front to the drawer glides.

4. Lift up on the drawer front to release the screws from the

drawer glide bracket slot.

A. Drawer glide bracket slots

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the top screws,

located at the bottom inside of the drawer front, with the

drawer glide bracket slots.

NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and inserts the

studs into the slots.

A. Drawer front screws

3. Tighten the two screws at the top of the drawer front (one

on the left-hand side and one on the right-hand side) and

replace the two screws on the bottom.

A

Final Steps

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See the “Using the Controls” section.

3. Return all removable parts and food to the drawers.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A

14

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Before you move your refrigerator into its nal location, it

is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115-volt, 60 Hz, AC-only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator and approved accessories

be provided. Use an outlet that cannot be turned off by a switch.

Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground

Fault Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and avor may be affected. If nuisance tripping has occurred,

and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation or cleaning, turn

off cooling, then disconnect the refrigerator from the electrical

source. When you have nished, reconnect the refrigerator to

the electrical source and turn on cooling. See the “Using the

Controls” section.

Water Supply Requirements

A cold water supply with water pressure between 35 and 120 psi

(241 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call

a licensed, qualied plumber.

NOTE: If the water pressure is less than what is required, the ow

of water from the water dispenser could decrease or ice cubes

could be hollow or irregular shaped.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out

of a reverse osmosis system going to the water inlet valve of

the refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).

If a reverse osmosis water ltration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

■Check to see whether the sediment lter in the reverse

osmosis system is blocked. Replace the lter if necessary.

■Allow the storage tank on the reverse osmosis system to rell

after heavy use. The tank capacity could be too small to keep

up with the requirements of the refrigerator.

NOTE: Faucet-mounted reverse osmosis systems are

not recommended.

■If your refrigerator has a water lter, it may further reduce

the water pressure when used in conjunction with a reverse

osmosis system. Remove the water lter. See the “Water

Filtration System” section.

If you have questions about your water pressure, call a licensed,

qualied plumber.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT:

■Plumbing must be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

■Copper and PEX tubing connections from the household

water line to the refrigerator are acceptable and will help

avoid off-taste or odor in your ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following Part Numbers: W10505928RP (7 ft [2.14 m] jacketed

PEX), 8212547RP (5 ft [1.52 m] PEX), or W10267701RP

(25 ft [7.62 m] PEX).

■Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

■Flat-blade screwdriver

■7/16" and 1/2" open-end wrenches or two adjustable

wrenches

■1/4" nut driver

NOTE: Do not use a piercing-type or 3/16" (4.76 mm) saddle

valve which reduces water ow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is

connected, turn off the ice maker.

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shut-off valve or the equivalent, served by

a 1/2"

(12.7 mm)

household supply line.

NOTE: To allow sufcient water ow to the refrigerator, a minimum

1/2" (12.7 mm) size household supply line is recommended.

A

B

C

D

A. Sleeve

B. Nut

C. Copper tubing (to refrigerator)

D. Household supply line (1/2" [12.7 mm] minimum)

15

4. Now you are ready to connect the copper tubing to the

shut-off valve. Use 1/4" (6.35 mm) O.D. (outside diameter)

soft copper tubing to connect the shut-off valve and the

refrigerator.

■Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

■Slip compression sleeve and compression nut onto copper

tubing as shown. Insert end of tubing into outlet end squarely

as far as it will go. Screw compression nut onto outlet end

with adjustable wrench. Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper tubing

5. Place the free end of the tubing into a container or sink and

turn on main water supply to ush out tubing until water is

clear. Turn off shut-off valve on the water pipe.

NOTE: Always drain the water line before making the nal

connection to the inlet of the water valve to avoid possible

water valve malfunction.

6. Bend the copper tubing to meet the water line inlet which

is located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Connect to Refrigerator

Follow the connection instructions specic to your model.

1. Remove plastic cap from water valve inlet port. Attach the

copper tubing to the valve inlet using a compression nut

and sleeve as shown. Tighten the compression nut. Do not

overtighten. Conrm copper tubing is secure by pulling on

copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks

when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a “P” clamp.

A

C

B

A. Copper tubing

B. “P” clamp

C. Compression nut

D. Compression sleeve

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See “Water and Ice Dispensers”

section.

NOTE: Allow 24 hours to produce the rst batch of ice. Discard

the rst three batches of ice produced. Allow three days to

completely ll the ice storage bin.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A

B

C

D

3. Turn on water supply to refrigerator and check for leaks.

Correct any leaks.

Handle Installation and Removal

Parts Included: refrigerator door handles (2), refrigerated drawer

handles (2), freezer drawer handle (1), 1/8" and 3/32" hex keys,

spare setscrew(s)

NOTE: The freezer drawer handle is shorter than the refrigerator

door handles. Handle style may vary by model.

Install Handles

Knob Assembly

IMPORTANT: Make sure to put together the knob assembly prior

to assembling the handle.

1. Remove the handles and knob assembly from the packaging

inside the refrigerator and place them on a soft surface.

2. Align the knob assembly with the lever at the middle of the

door.

3. Fully engage the knob assembly onto the lever.

4. While holding the knob assembly, insert the short end of the

3/32" hex key into the hole and slightly rotate the hex key

until the key is engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew just until the

setscrew begins to contact the lever. Fully tighten.

16

3. Firmly push the handle toward the door until the handle base

is ush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew just until it

begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed

without this extra tightening.

8. Repeat steps 2 through 7 to install the other handle onto the

adjacent refrigerator door.

Freezer Drawer

1. With the drawer closed, place the handle onto the shoulder

screws so that the setscrews are facing down toward the

oor.

A. Shoulder screw

B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle

base is ush against the drawer.

3. Insert the short end of the hex key into the left-hand hole and

slightly rotate the hex key until it is engaged in the setscrew.

4. Using a left-to-right motion, tighten the setscrew a quarter

turn at a time just until it begins to contact the shoulder

screw. Do not fully tighten.

5. Repeat steps 3 and 4 to fasten the right-hand setscrew to the

shoulder screw.

6. Once both setscrews have been partially tightened as

instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

Remove the Handles

1. While holding the handle, insert the short end of the hex key

into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a right-to-left motion, loosen the setscrew a quarter

turn at a time.

3. Repeat steps 1 and 2 for the other setscrew. Slowly pull the

handle away from the door or drawer.

4. If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

A

B

A. Shoulder screws

B. Setscrews inside the handle

Refrigerator Doors

NOTE: Handle mounting setscrews are preinstalled inside the

handle.

1. Remove the handles from the packaging inside the

refrigerator and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed

door, place a handle onto the shoulder screws so that the

setscrews are facing the adjacent door.

A

B

17

Refrigerator Leveling

and Door Closing

The base grille covers the adjustable brake feet and roller

assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the base

grille and move the refrigerator to its nal location.

Tools Needed: 1/4" (6.35 mm) hex driver

Tools Provided: 1/4" (6.35 mm) hex key

1. Use a 1/4" (6.35 mm) hex nut driver to remove both screws in

base grille.

2. Remove the base grille. Using both hands, grasp the grille

rmly and pull it toward you. Open the freezer drawer to

access the brake feet.

NOTE: To allow the refrigerator to roll easier, raise the brake

feet by turning them counterclockwise. The front rollers will

be touching the oor.

7. Make sure the refrigerator is steady. If the refrigerator seems

unsteady or rolls forward when a door or drawer is pulled

open, adjust the brake feet.

To Steady the Refrigerator:

■Open the freezer drawer. Using a 1/4" (6.35 mm) hex driver,

turn both brake feet clockwise the same amount until the

brake feet are snug against the oor. Check again. If not

satised, continue to adjust the brake feet by half turns of

the screw until the refrigerator does not roll forward when the

drawer is opened.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This makes

it easier to turn the screws.

8. Replace the base grille by aligning the ends of the grille with

the leveling assemblies on each side and snapping the grille

into place. Use a 1/4" (6.35 mm) hex nut driver to reinstall

screws.

A. Bottom hinge pin

B. 1/8" (3.18 mm) hex key wrench

3. Move the refrigerator to its nal location.

4. Using the 1/4" (6.35 mm) hex driver, lower the brake feet.

Turn them clockwise until the rollers are off the oor and

both brake feet are snug against the oor. This keeps the

refrigerator from rolling forward when opening the refrigerator

doors or freezer drawer.

IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the

same amount to keep the refrigerator level.

5. Use a level to make sure the refrigerator is level from side to

side and front to back.

6. Make sure the doors are even at the top and that the space

between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.

A

B

To Align the Doors:

■Keeping both refrigerator doors closed, pull out the freezer

drawer. Locate the bottom hinge pin of the right-hand

refrigerator door. The alignment screw is inside the bottom

hinge pin.

■ Insert the short end of the 1/8" (3.18 mm) hex key wrench

(packed with the Door Handle Installation Instructions) into

the bottom hinge pin until it is fully engaged in the alignment

screw.

To raise the refrigerator door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

■ Continue to turn the alignment screw until the doors are

aligned.

A. Handle medallion

Remove and Replace Handle Medallions (optional)

The handles for your model have red medallions on the ends.

Replacement medallions are available for purchase. See

“Accessories” to order.

1. Using a 1/8" (3.18 mm) hex key, remove the medallion from

the end of the handle.

2. Replace medallion.

3. Using the fastener removed in Step 1, attach the medallion to

the handle.

A

18

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Replace and Install the Water Filter

The water lter should be replaced every six months based on a

ow rate of .50 gpm—.60 gpm that lters 200 gallons (757.1 L) of

water.

To order a replacement lter, contact us. See “Accessories”

section in the User Guide for information on ordering.

NOTE: If the lter is not installed correctly, water may dispense

at a lower ow rate and there will be slower ice production.

Improper lter installation may also cause the water lter housing

to leak.

1. Push the water lter door to open, located bottom left of

refrigerator compartment.

2. Twist the water lter and turn 90° counterclockwise to unlock.

3. Pull the lter out of the housing.

4. Remove the water lter cap from the water lter.

5. Install the water lter cap onto the new lter. Be sure to align

the arrows so the groves in lter align with ribs in lter cap.

6. Insert the lter into the housing.

7. Twist the water lter and turn 90° clockwise until it locks into

place and that arrows are aligned.

8. Push the water lter door closed.

FILTERS AND ACCESSORIES

Water Filtration System

19

Install Air Filter

An air lter is 15 times more powerful than baking soda at

reducing common food odors inside the refrigerator.

On some models, your refrigerator’s accessory packet includes

an air lter which must be installed prior to use.

Installing the Air Filter

Install the air lter behind the blue LED-lighted vent cover, located

on the rear wall near the middle of the refrigerator.

1. Remove the air lter from its packaging.

2. Firmly grasp plastic cover on the vented cover with both

hands and pull out to remove.

NOTE: When cover is removed for the rst time, a small foam

part the size of the lter will need to be discarded.

3. Snap the lter into place.

A. Air filter

Replacing the Air Filter

The disposable air lter should be replaced every 6 months.

To order a replacement air lter, contact us. See “Accessories”

section in the User Guide for information on ordering.

1. Remove the used air lter by squeezing in on the side tabs.

2. Install the new air lter following the instructions in the

previous sections.

Install Produce Preserver

(on some models)

The produce preserver absorbs ethylene to slow the ripening

process of many produce items. As a result, certain produce

items will stay fresh longer.

Ethylene production and sensitivity varies, depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate-to-high amounts of ethylene.

Sensitivity

to Ethylene Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

A

The Water Filter Status Light

The water lter status lights will help you know when to change

your water lter.

■Order Filter (yellow): It is almost time to change the water

lter. “Order Filter” display is on all of the time but off in

Showroom mode and Sabbath mode.

■Replace Filter (red): Replace the water lter. While you are

dispensing water, “Replace Filter” icon will ash constantly

from the beginning to the end of dispensing. After 14 days

without replacing the Water Filter, the “Replace Filter” icon

will blink seven times and an alert tone will sound three times

at the end of dispensing.

■Reset Filter: Touch MAX COOL and MAX ICE together for 3

seconds to reset water lter. The display will do a 3-second

countdown, then ash the icon and play a tone.

Installing the Produce Preserver

For your convenience, the suction-mounted produce preserver

can be installed in either the crisper or the refrigerated drawers.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES

FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,

bleach or acids. Do not get in eyes, on skin or clothing. Do

not breathe dust. Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium

permanganate. If swallowed, call a Poison Control Center or

doctor immediately. Do not induce vomiting. If in eyes, rinse

with water for 15 minutes. If on skin, rinse with water.

1. Wash the interior of a drawer with a solution of mild dish soap

and warm water and dry thoroughly.

20

Accessories

The following accessories are available for your refrigerator.

To order an accessory, contact us and ask for the part number.

In the U.S.A., visit our website www.kitchenaid.com or call

1-800-422-1230.

In Canada, visit our webpage www.kitchenaid.ca or call

1-800-807-6777.

affresh® Stainless Steel Cleaner:

In U.S.A., order Part #W10355016

In Canada, order Part #W10355016B

affresh® Stainless Steel Wipes:

In U.S.A., order Part #W10355049

In Canada, order Part #W10355049B

affresh® Kitchen & Appliance Cleaner:

In U.S.A., order Part #W10355010

In Canada, order Part #W10355010B

Water Filter:

In U.S.A., order Part #EDR2RXD1

In Canada, order Part #EDR2RXD1B

Air Filter:

Order Part #W10311524 or AIR1

Produce Preserver Starter kit:

Order Part #P1UB6S1

Produce Preserver Rell kit:

Order Part #P1KC6R1

Door Handle Medallions:

Order Part #W10762987 (Black)

Order Part #W10762993 (Chrome)

REFRIGERATOR USE

Opening and Closing Doors

There are two refrigerator compartment doors. The doors can

be opened and closed either separately or together. There is

a vertically hinged seal on the left refrigerator door.

■When the left-side door is opened, the hinged seal

automatically folds inward so that it is out of the way.

■When both doors are closed, the hinged seal automatically

forms a seal between the two doors.

A

A. Hinged seal

2. Find the package containing the Produce Preserver inside the

refrigerator and install the Produce Preserver into the drawer

according to the instructions provided in the package.

Replacing the Produce Preserver

The disposable packet(s) should be replaced every 6 months or

when the status indicator changes completely from white to red.

To order replacements, contact us. See the “Accessories” section

for information on ordering.

1. Remove the used packets from the produce preserver

housing.

2. Remove the used status indicator.

3. Install the replacement packets and status indicator using the

instructions included in the package.

Door-within-Door

Use the hidden latch and left up to open the door-within-

door and get instant access to items and ingredients in your

refrigerator door bins

IMPORTANT: Do not open inner door when outer door is open.

Close outer door before opening inner door.

In-door Venting

The in-door venting will direct cold air in the lower door bin

area. Opening the shutter door (sliding it right) will make this

area colder, while closing the shutter door (sliding it left) will

make it less cold. This will keep milk and beverages at the right

temperature.

The refrigerator compartment door switch is located in the top

left and right hinge cover.

■The door switch uses magnet to sense door opening/closing.

■Ensure there are no magnet or electronic devices (Speaker,

CoolVox, etc) within 3 inches of the hinge cap.

NOTE: The light and internal user interface (UI) will not turn on if

the door opening is not detected.

La page charge ...

KitchenAid KRFC804GBS Guide d'installation

Ce manuel convient également à

KitchenAid KRFC804GBS Guide d'installation

dans d''autres langues