LG DV298H-NH Le manuel du propriétaire

Marque: LG

Modèle: DV298H-NH

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

DVD PLAYER

OWNER’S MANUAL

MODEL: LDA-831

Before connecting, operating or adjusting this product,

please read this instruction booklet carefully and completely.

DV298H-NH.HA1CLLB_ENG

http://www.lg.ca

This lightning flash with arrowhead symbol within

an equilateral triangle is intended to alert the user

to the presence of uninsulated dangerous voltage

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and maintenance

(servicing) instructions in the literature

accompanying the product.

WARNING: Do not install this equipment in a confined space

such as a bookcase or similar unit.

CAUTION: Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to protect

it from over heating.

The openings should never be blocked by placing the

product on a bed, sofa, rug or other similar surface. This

product should not be placed in a built-in installation such as

a bookcase or rack unless proper ventilation is provided or

the manufacturer's instruction have been adhered to.

CAUTION:

This product employs a Laser System.

To ensure proper use of this product, please read this

owner’s manual carefully and retain it for future reference.

Should the unit require maintenance, contact an authorized

service center.

Use of controls, adjustments or the performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open

the enclosure. Visible laser radiation when open. DO NOT

STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water

(dripping or splashing) and no objects filled with liquids, such

as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord

Most devices should be placed on a dedicated circuit;

That is, a single outlet circuit which powers only that

electronic device and has no additional outlets or branch

circuits. Check the specification page of this owner's manual

to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose

or damaged wall outlets, extension cords, frayed power

cords, or damaged or cracked wire insulation are dangerous.

Any of these conditions could result in electric shock or fire.

Periodically examine the cord of your appliance, and if its

appearance indicates damage or deterioration, unplug it,

discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse,

such as being twisted, kinked, pinched, closed in a door, or

walked upon. Pay particular attention to plugs, wall outlets,

and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord

plug. When installing the product, ensure that the plug is

easily accessible.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN

OR MOISTURE.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

1. Read these instructions. - All these safety and

operating instructions should be read before the product

is operated.

2. Keep these instructions. - The safety, operating and

use instructions should be retained for future reference.

3. Heed all warnings. - All warnings on the product and in

the operating instructions should be adhered to.

4. Follow all instructions. - All operating and use

instructions should be followed.

5. Do not use this apparatus near water. – For example:

near a bath tub, wash bowl, kitchen sink, laundry tub, in

a wet basement; or near a swimming pool; and other

areas located near water.

6. Clean only with dry cloth. – Unplug this product from

the wall outlet before cleaning. Do not use liquid

cleaners.

Do not block any ventilation openings. Install in

accordance with the manufacturer's instructions. -

Slots

and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to

protect it from over-heating. The openings should never

be blocked by placing the product on a bed, sofa, rug or

other similar surface. This product should not be placed

in a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the

manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The

wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the

obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to

avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND

THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This product has been designed and manufactured to assure personal safety. Improper use can result in electric shock or

fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for

installation, use, and servicing.

This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

Introduction . . . . . . . . . . . . . . . . . .5-8

About the Symbol Display . . . . . . . . . . . . .5

Symbol used in this Manual . . . . . . . . . . . . . .5

Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . .5

Handling Discs . . . . . . . . . . . . . . . . . . . . . . .5

Storing Discs . . . . . . . . . . . . . . . . . . . . . . . .5

Cleaning Discs . . . . . . . . . . . . . . . . . . . . . . .5

Types of Playable Discs . . . . . . . . . . . . . . . . .6

Regional Code . . . . . . . . . . . . . . . . . . . . . . . . .6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Remote Control . . . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Operation . . . . . . . . . . . . . .8

Remote Control Battery Installation . . . . . . .8

Installation and Setup . . . . . . . . .9-15

Setting up the Player . . . . . . . . . . . . . . . . . . . .9

DVD Player Connections . . . . . . . . . . . . . . . . .9

Video and Audio Connections to Your TV . . .9

Resolution setting . . . . . . . . . . . . . . . . . . . . .9

HDMI connection . . . . . . . . . . . . . . . . . . . .10

Audio Connection to Optional Equipment . .11

Displaying Disc Information On-Screen . . . .12

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . .12

General Operation . . . . . . . . . . . . . . . . . . .12

LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . .13

• Menu Language . . . . . . . . . . . . . . . . . . .13

• Disc Audio / Subtitle / Menu . . . . . . . . . .13

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . .13

• TV Aspect . . . . . . . . . . . . . . . . . . . . . . . .13

• Display Mode . . . . . . . . . . . . . . . . . . . . .13

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

• Dolby Digital / DTS / MPEG . . . . . . . . . .14

• Sample Freq. (Frequency) . . . . . . . . . . .14

• DRC (Dynamic Range Control) . . . . . . . .14

• Vocal . . . . . . . . . . . . . . . . . . . . . . . . . . .14

LOCK (Parental Control) . . . . . . . . . . . . . .14

• Rating . . . . . . . . . . . . . . . . . . . . . . . . . . .14

• Password . . . . . . . . . . . . . . . . . . . . . . . .14

• Area Code . . . . . . . . . . . . . . . . . . . . . . .15

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . .15

• PBC . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

• B.L.E. (Black Level Expansion) . . . . . . . .15

• DivX(R) VOD . . . . . . . . . . . . . . . . . . . . .15

Operations . . . . . . . . . . . . . . . .16-21

General Features . . . . . . . . . . . . . . . . . . . . . .16

Additional Features . . . . . . . . . . . . . . . . . . . .17

Playing an Audio CD or MP3/WMA file . . . . .18

Programmed Playback . . . . . . . . . . . . . . . . .18

Repeat Programmed Tracks . . . . . . . . . . . .18

Erasing a Track from Program List . . . . . . .18

Erasing the Complete Program List . . . . . .18

Viewing a JPEG file . . . . . . . . . . . . . . . . . . . .19

Slide Show . . . . . . . . . . . . . . . . . . . . . . . . .19

Still Picture . . . . . . . . . . . . . . . . . . . . . . . . .19

Moving to another File . . . . . . . . . . . . . . . .19

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Rotating the picture . . . . . . . . . . . . . . . . . .19

Listening to MP3/WMA music while watching

picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Playing a DivX Movie file . . . . . . . . . . . . . . .20

Playing a DVD VR Format Disc . . . . . . . . . . .21

Playing an USB Flash Drive . . . . . . . . . . . . .21

Reference . . . . . . . . . . . . . . . . . .22-24

Controlling other TV’s with the Remote Control 22

Maintenance and Service . . . . . . . . . . . . . . . .22

Language Codes . . . . . . . . . . . . . . . . . . . . . . .23

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . .24

Specifications . . . . . . . . . . . . . . . . . . . . . . . . .24

Contents

Operation Reference

Installation and Setup

To ensure proper use of this product, please read this

owner’s manual carefully and retain it for future

reference.

This manual provides information on the operation

and maintenance of your DVD player. Should the unit

require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during

operation and indicates that the function explained in

this owner’s manual is not available on that specific

Disc.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols is

applicable only to the disc represented by the symbol.

All discs and file listed below

DVD and finalized DVD±R/RW

Video CDs

Audio CDs

MP3 files

WMA files

DivX files

Notes on Discs

Handling Discs

Do not touch the playback side of the disc. Hold the

disc by the edges so that fingerprints do not get on

the surface. Never stick paper or tape on the disc.

Storing Discs

After playing, store the disc in its case. Do not expose

the disc to direct sunlight or sources of heat and never

leave it in a parked car exposed to direct sunlight.

Cleaning Discs

Fingerprints and dust on the disc can cause poor

picture quality and sound distortion. Before playing,

clean the disc with a clean cloth. Wipe the disc from

the center out.

Do not use strong solvents such as alcohol, benzine,

thinner, commercially available cleaners, or anti-static

spray intended for older vinyl records.

DivX

WMA

MP3

ACD

VCD

DVD

ALL

Introduction

Types of Playable Discs

DVD

(8 cm / 12 cm disc)

Video CD (VCD/SVCD)

(8 cm / 12 cm disc)

Audio CD

(8 cm / 12 cm disc)

In addition, this unit plays DVD±R/RW and CD-R/RW,

Dual disc, USB Flash Drive that contains audio titles,

DivX, MP3, WMA, and/or JPEG files.

This indicates a product feature that is

capable of playing DVD-RW discs

recorded with Video Recording format.

Notes:

• Depending on the conditions of the recording

equipment or the CD-R/RW (or DVD±R/RW) disc

itself, some CD-R/RW (or DVD±R/RW) discs

may not be played on the unit.

• Do not use irregularly shaped CDs (e.g., heart-

shaped or octagonal) since they may result in

malfunctions.

• This DVD player requires discs and recordings to

meet certain technical standards in order to achieve

optimal playback quality. Pre-recorded DVDs are

automatically set to these standards. There are

many different types of recordable disc formats

(including CD-R containing MP3 or WMA files) and

these require certain pre-existing conditions (see

above) to ensure compatible playback.

Customers should note that permission is

required in order to download MP3 / WMA files

and music from the Internet. Our company has

no right to grant such permission. Permission

should always be sought from the copyright

owner.

Regional Code

This unit has a regional code printed on the rear of the

unit. This unit can play only DVD discs labeled as the

same as the rear of the unit or “ALL”.

Notes on Regional Codes

• Most DVD discs have a globe with one or more

numbers in it clearly visible on the cover. This

number must match your unit’s regional code or the

disc cannot play.

• If you try to play a DVD with a different regional

code from your player, the message “Check

Regional Code” appears on the TV screen.

Notes on Copyrights:

It is forbidden by law to copy, broadcast, show,

broadcast via cable, play in public, or rent copyrighted

material without permission. This product features the

copy protection function developed by Macrovision.

Copy protection signals are recorded on some discs.

When recording and playing the pictures of these discs

picture noise will appear. This product incorporates

method claims of certain U.S. patents and other

intellectual property rights owned by Macrovision

Corporation and other rights owners.

The Use of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended

for home and other limited viewing uses only unless

otherwise authorized by Macrovision Corporation.

Reverse engineering or disassembly is prohibited.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH

DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE. IN CASE OF 525 PROGRESSIVE SCAN

PICTURE PROBLEMS, IT IS RECOMMENDED THAT

THE USER SWITCH THE CONNECTION TO THE

‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE

QUESTIONS REGARDING OUR TV SET

COMPATIBILITY WITH THIS MODEL 525p DVD

PLAYER, PLEASE CONTACT OUR CUSTOMER

SERVICE CENTER.

Operation Reference

Installation and Setup

Introduction

Front Panel

a POWER

Switches the unit ON or OFF.

b • N (PLAY)

Starts playback.

• x (STOP)

Stops playback.

• . (SKIP)

Returns to the beginning of current chapter or

track or go to the previous chapter or track.

• > (SKIP)

Go to the next chapter or track.

c Disc Tray

Insert a disc here.

d Display window

Shows the current status of the unit.

e Remote Sensor

Point the Remote Control here.

f USB

Connect an USB Flash Drive.

g Z (OPEN / CLOSE)

Opens or closes the disc tray.

h RES.

Sets the output resolution for HDMI and

COMPONENT OUTPUT jacks.

a b

cdef gh

Remote Control

Remote Control Operation

Point the Remote Control at the remote sensor and

press the buttons.

Caution:

Do not mix old and new batteries and never mix

different types of batteries such as standard, alkaline,

etc.

Remote Control Battery installation

Detach the battery cover on the rear of the

Remote Control, and insert two batteries

(size AAA) with 3 and # aligned correctly.

POWER(1)

Switches DVD Player ON and OFF.

OPEN/CLOSE (Z)

Opens and closes the disc tray.

0-9 numerical buttons

Selects numbered items in a menu.

CLEAR

Removes a track number on the

Program List or a mark on the

Marker Search menu.

TV Control Buttons

POWER: Turns the TV on or off.

AV: Selects the TV’s source.

PR/CH +/–: Selects TV’s channel.

VOL +/–: Adjusts TV’s volume.

MARKER

Marks any point during playback.

Displays MARKER SEARCH menu.

PROGRAM

Enter the program edit mode.

ZOOM

Enlarges video image.

REPEAT

Repeat chapter, track, title, all.

A-B

Repeat sequence from point A

to point B.

RANDOM

Plays tracks in random order.

RESOLUTION

Sets the output resolution for HDMI

and COMPONENT OUTPUT jacks.

SCAN (m / M)

Search backward or forward.

SKIP (. / >)

Go to next chapter or track.

Returns to the beginning of current

chapter or track or go to the

previous chapter or track.

PAUSE/STEP ( X )

Pauses playback temporarily/ press

repeatedly for frame-by-frame

playback.

PLAY (N)

Starts playback.

STOP (x)

Stops playback.

DVD MENU

Accesses menu on a DVD disc.

TITLE

Displays title menu, if available.

b / B / v / V (left/right/up/down)

Selects an item in the menu.

ENTER(



)

Confirms menu selection.

DISPLAY

Accesses On-Screen Display.

RETURN (O)

Hide the help menu while watching

a JPEG file.

AUDIO( )

Selects an audio language or an

audio channel.

SUBTITLE( )

Selects a subtitle language.

ANGLE( )

Selects a DVD camera angle,

if available.

SETUP

Accesses or removes the Setup

menu.

Operation Reference Introduction

Installation and Setup

Setting up the Player

The picture and sound of a nearby TV, VCR, or radio

may be distorted during playback. If this occurs,

position the player away from the TV, VCR, or radio, or

turn off the unit after removing the disc.

DVD Player Connections

Depending on your TV and other equipment there are

various ways you can connect the player. Please refer to

the manuals of your TV, stereo system or other devices

as necessary for additional connection information.

Video and Audio Connections

to Your TV

Make sure the unit is connected directly to the TV and

not to a VCR, otherwise the DVD image could be

distorted by the copy protection system.

S-Video – Connect the S-VIDEO OUT jack on the

unit to the S-Video in jack on the TV using the S-

Video cable (S).

Video – Connect the VIDEO OUT jack on the unit

to the video in jack on the TV using the video cable

(V).

Audio – Connect the left and right AUDIO OUT

jacks of the unit to the audio left and right IN jacks

on the TV using the audio cables (A).

Do not connect the unit AUDIO OUT jack to the

phone in jack (record deck) of your audio system.

Component Video – Connect the COMPONENT /

PROGRESSIVE SCAN jacks on the unit to the

corresponding jacks on the TV using an Y P

B PR

cable (C).

Resolution setting

1. Press RESOLUTION once. The current resolution

setting will appear on the display window.

2. Press RESOLUTION repeatedly to change the

resolution you want.

The available resolution according to the connections

are as shown below.

Notes:

• The resolution of the VIDEO and S-VIDEO OUTPUT

is fixed to 480i.

• If your TV does not accept your resolution setting,

abnormal picture appears on the screen.

Please read TV’s owner’s manual then set the

resolution that your TV can accept.

• For 720p, 1080i and 1080p resolution on the

component video out, only non-copy protected discs

can be played back. If the disc is copy protected, it

will be displayed at the 480p resolution.

• Depending on your TV, certain HDMI output

resolutions may not work.

• Only resolutions supported by the TV are available.

Progressive Scan

• If your television is a high-definition or “digital ready”

television, you may take advantage of the unit

progressive scan output for the highest possible

video resolution.

•

Progressive scan does not work with the analog video

connections (yellow VIDEO OUT and

S-Video jack).

• The 1080p, 720p and 480p resolutions are the

progressive scan applied resolution.

Note for 1080p resolution

This unit is able to provide a 1080p full HD image to

most 1080p-capable TVs in the market today.

However, there are some 1080p TVs available from

certain companies that are limited in the types of

1080p images that can be accepted. Specifically,

1080p-capable TVs that don’t accept images in 60Hz

can’t display an image from this unit.

Installation and Setup

OUTPUT CONNECTION

Available Resolution

HDMI

VIDEO OUT

COMPONENT

VIDEO OUT

1920 x 1080p

1920 x 1080i

1280 x 720p

720 x 480p

720 x 480i

1920 x 1080p

1920 x 1080i

1280 x 720p

720 x 480p

720 x 480i

S-VIDEO

720 x 480i

HDMI connection

If you have a HDMI TV or monitor, you can connect it

to this unit using a HDMI cable.

1. Connect the HDMI OUTPUT jack on the unit to the

HDMI INPUT jack on a HDMI compatible TV or

monitor (H).

2. Set the TV’s source to HDMI (refer to TV’s Owner’s

manual).

Notes:

• If your TV is NOT capable of handling 96 kHz

sampling frequency, set the [Sampling Freq.] option

to [48 kHz] on the setup menu (See page 14).

When this choice is made, this unit will

automatically convert any 96 kHz signals to 48 kHz

so your system can decode them.

•

If your TV is not equipped with Dolby Digital and

MPEG decoder, set the [Dolby Digital] and [MPEG]

options to [PCM] on the setup menu (See page 14).

• If your TV is not equipped with DTS decoder, set

the [DTS] options to [Off] on the setup menu (See

page 14). To enjoy DTS multi channel surround,

you must connect this unit to a DTS compatible

receiver via one of this unit’s digital audio outputs.

• The arrow on the cable connector body should face

up for correct alignment with the connector on the

unit.

• If there is noise or lines on the screen, please

check the HDMI cable.

• Not all HDCP-compatible

Tip:

When you use HDMI connection, you can change the

resolution (480i, 480p, 720p, 1080i or 1080p) for the

HDMI output using RES. button on the front panel.

Caution:

 Changing the resolution when the unit is connected

with HDMI connector may result in malfunctions. To

solve the problem, turn off the unit and then turn it

on again.

 If your TV does not accept your resolution setting,

abnormal picture appears on the screen.

Please read TV’s owner’s manual then set the

resolution that your TV can accept.

About HDMI

HDMI (High Definition Multimedia Interface) supports

both video and audio on a single digital connection for

use with DVD Players, Set-Top Boxes, and other AV

devices.

HDMI was developed to provide the technologies of

HDCP (

High-bandwidth Digital Content Protection

HDCP is used to protect digital content transmitted and

received.

HDMI has the capability to support standard, enhanced,

or high-definition video plus standard to multi-channel

surround-sound audio, HDMI features include

uncompressed digital video, a bandwidth of up to 5

gigabytes per second, one connector (instead of several

cables and connectors), and communication between the

AV source and AV devices such as DTVs.

HDMI, the HDMI logo and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI licensing LLC.

Additional Information for HDMI

• When you connect a HDMI or DVI compatible

device make sure of the following:

- Try switching off the HDMI/DVI device and this

unit. Next, switch on the HDMI/DVI device and

leave it for around 30 seconds, then switch on

this unit.

- The connected device’s video input is set

correctly for this unit.

- The connected device is compatible with

720(1440)x480i, 720x480p, 1280x720p,

1920x1080i, or 1920x1080p video input.

• Not all HDCP-compatible DVI devices will work

with this unit.

- It’s impossible copy protected-DVD title’s

playback in non-HDCP devices.

• For best performance, directly connect the HDMI

output to an HDMI input on your TV. If connecting

to some device other than a TV or monitor, such

as a home theater receiver with an HDMI input,

check the following to make sure the HDMI signal

will be received correctly:

- Check the operating instructions of the

connected device to make sure that the HDMI

input of the device complies with HDMI-HDCP

specifications.

- Check that the HDMI setup menu of any non-

display device is set to “pass-through” so that

HDMI signals received are not changed in any

way (such as changing the video or audio

format).

Operation Reference Introduction

Installation and Setup

Audio Connection to Optional

Equipment

Connect the unit to your optional equipment for audio

output.

Amplifier equipped with 2-channel analog stereo

or Dolby Pro Logic ll / Pro Logic: Connect the left

and right AUDIO OUT jacks on the unit to the audio

left and right IN jacks on your amplifier, receiver, or

stereo system, using the audio cables (A).

Amplifier equipped with 2-channel digital stereo

(PCM) or audio / video receiver equipped with a

multi-channel decoder (Dolby Digital™, MPEG 2,

or DTS):

Connect one of the unit DIGITAL AUDIO OUT jacks

(OPTICAL O or COAXIAL X) to the corresponding

jack on your amplifier. Use an optional digital

(OPTICAL O or COAXIAL X) audio cable.

Digital Multi-channel sound

A digital multi-channel connection provides the best

sound quality. For this you need a multi-channel audio

/ video receiver that supports one or more of the

audio formats supported by your unit such as

MPEG 2, Dolby Digital and DTS. Check the receiver

manual and the logos on the front of the receiver.

Notes:

• If the audio format of the digital output does not match

the capabilities of your receiver, the receiver produces

a strong, distorted sound or no sound at all.

• Six Channel Digital Surround Sound via a digital

connection can only be obtained if your receiver is

equipped with a Digital Multi-channel decoder.

Manufactured under license from Dolby

Laboratories. “Dolby”, “Pro Logic” and

the double-D symbol are trademarks of

Dolby Laboratories.

DTS and DTS Digital Out are trademarks

of Digital Theater Systems, Inc.

Displaying Disc Information

On-Screen

You can display various information about the disc

loaded on-screen.

1. Press DISPLAY to show various playback

information.

The displayed items differ depending on the disc

type or playing status.

2. You can select an item by pressing v / V and

change or select the setting by pressing b / B.

• Title – Current title. number/total number of

titles.

• Chapter – Current chapter number/total number

of chapters.

• Time – Elapsed playing time.

• Audio – Selected audio language or channel.

• Subtitle – Selected subtitle.

• Angle – Selected angle/total number of angles.

Note:

If any button is not pressed for a few seconds, the on-

screen display disappears.

Initial Settings

By using the Setup menu, you can make various

adjustments to items such as picture and sound.

You can also set a language for the subtitles and the

Setup menu, among other things. For details on each

Setup menu item, see pages 13 to 15.

To display and exit the Menu:

Press SETUP to display the menu. A second press of

SETUP will take you back to initial screen.

To go to the next level:

Press B on the Remote Control.

To go back to the previous level:

Press b on the Remote Control.

General Operation

1. Press SETUP.

The Setup menu appears.

2. Use v / V to select the desired option then press

B to move to the second level. The screen shows

the current setting for the selected item, as well as

alternate setting(s).

3. Use v / V to select the second desired option and

then press B to move to the third level.

4. Use v / V to select the desired setting then press

ENTER to confirm your selection.

Some items require additional steps.

5. Press SETUP or PLAY (N) to exit the Setup

menu.

Operation Reference Introduction

Installation and Setup

LANGUAGE

Menu Language

Select a language for the Setup menu and on-screen

display.

Disc Audio / Subtitle / Menu

Select the language you prefer for the audio track

(disc audio), subtitles, and the disc menu.

Original – Refers to the original language in which

the disc was recorded.

Other – To select another language, press

numeric buttons and then ENTER to enter the

corresponding 4-digit number according to the

language code list on the page 23. If you enter the

wrong language code, press CLEAR.

Off (for Disc Subtitle) – Turn off Subtitle.

DISPLAY

TV Aspect

4:3 – Select when a standard 4:3 TV is connected.

16:9 – Select when a 16:9 wide TV is connected.

Notes

If the TV Aspect option is set to 16:9, the Display

Mode setting is automatically set to Widescreen.

Display Mode

The Display Mode setting works only when the TV

Aspect mode is set to 4:3.

Letterbox – Displays a wide picture with bands on

the upper and lower portions of the screen.

Panscan – Automatically displays the wide picture

on the entire screen and cuts off the portions that

do not fit.

AUDIO

Each DVD disc has a variety of audio output options.

Set the player’s AUDIO options according to the type

of audio system you use.

Dolby Digital / DTS / MPEG

Bitstream – Select “Bitstream” if you connect this

unit’s DIGITAL OUT jack to an amplifier or other

equipment with a Dolby Digital, DTS or MPEG

decoder.

PCM (for Dolby Digital / MPEG) – Select when

connected to a two-channel digital stereo amplifier.

DVDs encoded in Dolby Digital, MPEG will be

automatically downmixed to two-channel PCM

audio.

Off (for DTS) – If you select “Off”, the DTS signal

is not output through the DIGITAL OUT jack.

Sample Freq. (Frequency)

If your receiver or amplifier is NOT capable of handling

96 kHz signals, select 48 kHz. When this choice is

made, this unit automatically converts any 96 kHz

signals to 48 kHz so your system can decode them.

If your receiver or amplifier is capable of handling 96

kHz signals, select 96 kHz.

Check the documentation for your amplifier to verify

its capabilities.

DRC (Dynamic Range Control)

With the DVD format, you can hear a program’s

soundtrack in the most accurate and realistic

presentation. However, you may wish to compress the

dynamic range of the audio output (the difference

between the loudest sounds and the quietest ones).

This allows you to listen to a movie at a lower volume

without losing clarity of sound.

Set DRC to On for this effect.

Vocal

Set to On only when a multi-channel karaoke DVD is

playing. The karaoke channels on the disc mix into

normal stereo sound.

LOCK (Parental Control)

Rating

Blocks playback of rated DVDs based on their

contents. Not all discs are rated.

1. Select “Rating” on the LOCK menu then

press B.

2. To access the LOCK options, you must input the

password you have created. If you have not yet

entered password, you are prompted to do so.

Input a password and press ENTER. Enter it again

and press ENTER to verify. If you make a mistake

before pressing ENTER, press CLEAR.

3. Select a rating from 1 to 8 using the v / V buttons.

Rating 1-8: Rating one (1) has the most

restrictions and rating eight (8) is the least

restrictive.

Unlock

If you select unlock, parental control is not active

and the disc plays in full.

4. Press ENTER to confirm your rating selection, then

press SETUP to exit the menu.

Password

You can enter or change password.

1. Select Password on the LOCK menu and then

press B.

2. To make a new password:

Press ENTER when the “New” option is

highlighted. Enter a new password using the

numerical buttons then press ENTER. Enter the

password again to verify.

To change the password:

Press ENTER when the “Change” option is

highlighted. Enter a current password using the

numbered buttons then press ENTER. Enter a new

password using the numbered buttons then press

ENTER. Enter the password again to verify.

3. Press SETUP to exit the menu.

If you forget your password

If you forget your password, you can clear it using the

following steps:

1. Press SETUP to display the Setup menu.

2. Input the 6-digit number “210499” and the

password is cleared.

Area Code

Enter the code of the area whose standards were

used to rate the DVD video disc, based on the list on

page 23.

1. Select “Area Code” on the LOCK menu then

press B.

2. Follow the step 2 as shown left (Rating).

3. Select the first character using v / V buttons.

4. Press ENTER and select the second character

using v / V buttons.

5. Press ENTER to confirm your Area code selection.

OTHERS

PBC

Set Playback Control (PBC) to On or Off.

On: Video CDs with PBC are played according to

the PBC.

Off: Video CDs with PBC are played in the same

way as Audio CDs.

B.L.E. (Black Level Expansion)

To select the black level of playback pictures.

Set your preference and monitor’s ability.

On: Expanded grey scale. (0 IRE cut off)

Off: Standard grey scale. (7.5 IRE cut off)

DivX(R) VOD

We provide you the DivX

VOD (Video On Demand)

registration code that allows you to rent and purchase

videos based on the DivX

VOD service. For more

information, visit www.divx.com/vod.

1. Select “DivX(R) VOD” option and then press B.

2. Press ENTER while “Select” is selected and the

registration code will appear.

Use the registration code to purchase or rent the

videos from DivX

VOD service at

www.divx.com/vod. Follow the instructions and

download the video onto a disc for playback on

this unit.

3. Press ENTER to exit.

Note:

All the downloaded videos from DivX

VOD can only

be played back on this unit.

Installation and Setup

Operations

General Features

Buttons Operations

OPEN/CLOSE (Z) Opens or closes the disc tray.

PAUSE/STEP (X) During playback, press PAUSE/STEP (X) to pause

playback.

Press PAUSE/STEP (X) repeatedly to play Frame-by-

Frame.

SKIP (. / >) During playback, press SKIP (. or >) to go to the

next chapter/track or to return to the beginning of the

current chapter/track.

Press SKIP (.) twice briefly to step back to the

previous chapter/track.

SCAN (m / M) During playback, press SCAN (m or M) repeatedly to

select the required scan speed.

DVD, DivX disc; 4 steps

Video CD, MP3, WMA, Audio CD: 3 steps

While the playback is paused, press SCAN (M)

repeatedly to play in slow motion (4 steps).

REPEAT During playback, press REPEAT repeatedly to select a

desired repeat mode.

DVD Video discs: Chapter/Title/Off

Video CD, Audio CD, DivX/MP3/WMA discs: Track/All/Off

A-B Press the A-B button one at a time to select a point A and

point B and repeats a sequence from point A (Starting

point) to point B (End point). Press A-B again to cancel.

ZOOM During playback or pause mode, press ZOOM to enlarge

the video image (3 steps).

You can move through the zoomed picture using

b / B / v / V buttons. Press CLEAR to exit.

RANDOM During playback or in stop mode, press RANDOM for

random playback.

TITLE If the current DVD title has a menu, the title menu

appears on the screen. Otherwise, the disc menu may

appears.

DVD MENU The disc menu appears on the screen.

ANGLE ( ) During playback of DVD disc that contains scenes

recorded at different camera angles, press ANGLE ( )

repeatedly to select a desired angle.

SUBTITLE ( ) During playback, press SUBTITLE ( ) repeatedly to

select a desired subtitle language.

AUDIO ( ) During playback, press AUDIO( ) repeatedly to hear a

different audio language or audio track.

Discs

(forward only)

VCDDivXDVD

DivXDVD

DVD

WMA

MP3

ACD

VCD

DivXVCDDVD

ACD

DivXVCDDVD

ALL

DivX

VCD

DVD

ALL

DivXVCDDVD

ALL

Reference

Installation and

Setup

Introduction

Operation

Notes on general features:

• On a Video CD with PBC, you must set PBC to Off

on the setup menu to use the repeat function (See

“PBC” on page 15).

• If you press SKIP (>) once during Repeat Chapter

(Track) playback, the repeat playback cancels.

• Zoom may not work on some DVDs.

• When you are playing a DVD disc that contains

scenes recorded at different camera angles, the

angle indicator will blink on the TV screen during the

oprations as an indication that angle switching is

possible

• If you press . once within 3 seconds after the

chapter/track has started, the playback goes to the

previous chapter/track.

Additional Features

Time Search

To start playing at any chosen time on the disc:

1. Press DISPLAY during playback.

2. Press v / V to select the time clock icon and

“--:--:--” appears.

3. Input the required start time in hours, minutes, and

seconds from left to right. If you enter the wrong

numbers, press CLEAR to remove the numbers

you entered. Then input the correct numbers.

4. Press ENTER to confirm.

Playback starts from the selected time.

Marker Search

To enter a Marker

You can start playback from up to nine memorized

points. To enter a marker, press MARKER at the

desired point on the disc. The Marker icon appears on

the TV screen briefly. Repeat to enter up to nine

markers.

To Recall or Clear a Marked Scene

1. During disc playback, press SEARCH. The marker

search menu appears on the screen.

2. Within 9 seconds, press b / B to select a marker

number that you want to recall or clear.

3. Press ENTER and playback starts from the marked

scene. Or, Press CLEAR and the marker number is

erased from the list.

4. You can play any marker by inputting its number on

the marker search menu.

Last Scene Memory

This unit memorizes last scene from the last disc that

is viewed. The last scene remains in memory even if

you remove the disc from the unit or switch off the unit.

If you load a disc that has the scene memorized, the

scene is automatically recalled.

Note:

This unit does not memorize the scene of a disc if you

switch off the unit before commencing to play the disc.

Screen Saver/Auto Power off

The screen saver appears when you leave the unit in

Stop mode for about five minutes. If the Screen Saver

is displayed for five minutes, the unit automatically

turns itself off.

VCD1.1

ACDDVD

DivXVCDDVD

Playing an Audio CD or

MP3/WMA file

This unit can play Audio CDs or MP3/WMA files.

MP3/ WMA/ Audio CD

Once you insert an MP3/WMA files recorded media or

Audio CD, a menu appears on the TV screen.

Use v / V to select a track/file and then press

PLAY (N) or ENTER and playback starts.

You can use variable playback functions.

Refer to page 16-17.

ID3 TAG

When playing a file containing information such as

track titles, you can see the information by pressing

DISPLAY. [ Title, Artist, Album, Year, Comment ]

Tips:

• Press DVD MENU to move to the next page.

• On a DISC with MP3/WMA and JPEG file, you can

switch MUSIC and PHOTO menu. Press TITLE, and

MUSIC or PHOTO word on top of the menu is

highlighted.

Programmed Playback

The program function enables you to store your

favorite tracks from any disc in the unit memory.

A program can contain 30 tracks.

1. Insert an Audio CD or MP3/WMA files recorded

media. AUDIO CD or MUSIC menu appears.

2. Press PROGRAM and the mark will appear.

Note:

Press PROGRAM again to exit the program edit

mode, then the mark will disappear.

Video CD: Press PROGRAM while playback is

stopped. The program menu appears. Press

PROGRAM again to exit the menu.

Note:

On a Video CD with PBC, you must set PBC to Off on

the setup menu to use the programmed playback

(See “PBC” on page 15).

3. Select a track on the “List” and then press ENTER

to place the selected track on the “Program” list.

Repeat to place additional tracks on the list.

4. Use b / B / v / V to select the track you want to

start playing on the “Program” list.

5. Press PLAY (N) or ENTER to start.

Playback begins in the order in which you

programmed the tracks. Playback stops after all of

the tracks on the “Program” list have played once.

6. To resume normal playback from programmed

playback, select a track on the list and then press

PLAY (N).

Repeat Programmed Tracks

Press REPEAT to select a desired repeat mode.

• Track: Repeats the current track.

• All: Repeats all the tracks on programmed list.

• Off(No display): Does not play repeatedly.

Note:

If you press SKIP (>) once during Repeat Track

playback, the repeat playback cancels.

Erasing a Track from Program List

1. Press PROGRAM and the mark will appear

2. Use b / B / v / V to select the track that you wish

to erase from the Program list.

3. Press CLEAR. Repeat step 1-3 to erase additional

tracks on the program list.

Erasing the Complete Program List

1. Press PROGRAM and the mark will appear

2. Use b / B / v / V to select “Clear All” and then

press ENTER.

Note:

The programs are also cleared when the power is

off or the disc is removed.

MP3 / WMA disc compatibility with this unit is

limited as follows:

• Sampling frequency: within 8 - 48 kHz (MP3),

within 22 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3),

32 - 256 kbps (WMA)

• The player cannot read an MP3/WMA file that has

a file extension as non than “.mp3” / “.wma”.

• CD-R physical format should be ISO 9660

• If you record MP3 / WMA files using software that

cannot create a file system (eg. Direct-CD) it is

impossible to playback MP3 / WMA files.

We recommend that you use Easy-CD Creator,

which creates an ISO 9660 file system.

• File names should have a maximum of 8 letters

and must incorporate an .mp3 or .wma extension.

• They should not contain special letters such as / ?

* : “ < > l etc.

• The total number of files in a folder should be less

than 650 files.

Operation

Viewing a JPEG file

This unit can play JPEG files.

1. Insert a JPEG files recording media.

The PHOTO menu appears on the TV screen.

2. Press v / V to select a folder, and press

ENTER. A list of files in the folder appears.

3. If you want to view a particular file, press

v / V to highlight a file and press ENTER or

PLAY (N).

4. To return to the PHOTO menu while watching

pictures, press STOP (x).

Tips:

• If you are in a file list and want to return to the

previous Folder list, use v / V buttons to highlight

and press ENTER.

• Press DVD MENU to move to the next page.

• There are three Slide Speed options : >>>

(Fast), >> (Normal) and > (Slow).

Use b / B / v / V to highlight . Then, use b / B

to select the option you want to use.

• On a DISC with MP3/WMA and JPEG file, you can

switch MUSIC and PHOTO menu. Press TITLE, and

MUSIC or PHOTO word on top of the menu is

highlighted.

• While watching a picture, press RETURN (O) to

hide the help menu.

Slide Show

Use b / B / v / V to highlight the (Slide Show)

then press ENTER.

Still Picture

1. Press PAUSE/STEP (X) during slide show.

The player will now go into pause mode.

2. To return to the slide show, press PLAY (N) or

press PAUSE/STEP (X) again.

Moving to another File

Press SKIP (. or >) or cursor (b or B) once

during viewing a picture to advance to the next or

previous file.

Zoom

During watching pictures, press ZOOM to enlarge the

video image (3 steps).

You can move through the zoomed picture using

b / B / v / V buttons. Press CLEAR to exit.

Rotating the picture

Press v / V during showing a picture to rotate the

picture clockwise or counter clockwise.

Listening to MP3/WMA music while watching

picture

1. Insert the disc containing the two types of file in

the player.

2. Press TITLE to display the PHOTO menu.

3. Press v / V to select a photo file.

4. Use B to select icon then press ENTER.

Playback starts. The playback will continue until

stop is pressed.

Tip:

To listen to only the desired music while watching

picture, program the desired tracks from the “MUSIC”

menu and then proceed as above.

JPEG disc compatibility with this player is

limited as follows:

• Depending upon the size and the number of

JPEG files, it could take a long time for the unit to

read the disc’s contents. If you do not see an on-

screen display after several minutes, some of the

files may be too large — reduce the resolution of

the JPEG files to less than 5 million pixels and

burn another disc.

• The total number of files in a folder should be less

than 650 files.

• Some discs may be incompatible due to a

different recording format or the condition of disc.

• Ensure that all the selected files have the “.jpg”

extensions when copying into the CD layout.

• If the files have “.jpe” or “.jpeg” extensions, please

rename them as “.jpg” file.

• File names without “.jpg” extension will not be

able to be read by this unit. Even though the files

are shown as JPEG image files in Windows

Explorer.

Playing a DivX Movie file

Using this DVD Player you can play DivX file.

1. Insert a DivX file recording media. The MOVIE

menu appears on the TV screen.

2. Press v / V to select a folder and then press

ENTER. A list of files in the folder appears.

3. If you want to view a particular file, press v / V to

highlight a file and press ENTER or PLAY. You can

use variable playback functions. Refer to page

16-17.

4. To return to the MOVIE menu during playback,

press STOP.

Tips:

• If you are in a file list and want to return to the

previous Folder list, use v / V buttons to highlight

and press ENTER.

• Press DVD MENU to move to the next page.

• On a DISC with MP3/WMA, JPEG and MOVIE file,

you can switch MUSIC, PHOTO and MOVIE menu.

Press TITLE, and MUSIC, PHOTO or MOVIE word

on top of the menu is highlighted.

• The disc subtitle may not be displayed properly, if a

DivX subtitle is downloaded through the internet.

• If the disc subtitle setup menu does not have the

DivX subtitle language you are going to play, the

subtitle language may not be displayed properly.

Notice for displaying the DivX subtitle

If the subtitle does not display properly, please follow

the steps below.

1. Press and hold SUBTITLE for about 3 seconds.

The language code will appear.

2. Press b / B to select another language code until

the subtitle is displayed properly.

3. Press ENTER to continue playback.

Note:

The DivX subtitle file name has to be identified with

the DivX file name to display by this unit.

DivX disc compatibility with this player is limited

as follows:

• Available resolution size of the DivX file is under

720x576 (W x H) pixel.

• The file name of the DivX subtitle is available by

56 characters.

• If there is impossible code to express in the DivX

file, it may be displayed as " _ " mark on the

display.

• If the number of the screen frame is over 30

per 1 second, this unit may not operate

normally.

• If the video and audio structure of recorded

file is not interleaved, either video or audio is

outputted.

• If the file is recorded with GMC, the unit

supports only 1-point of the record level.

GMC?

GMC is the acronym for Global Motion

Compensation. It is an encoding tool specified in

MPEG4 standard. Some MPEG4 encoders, like

DivX, have this option.

There are different levels of GMC encoding,

usually called 1-point, 2-point, or 3-point GMC.

Playable DivX file

.avi, .mpg, .mpeg

Playable Subtitle format

SubRip(*.srt/*.txt)

SAMI(*.smi)

SubStation Alpha(*.ssa/*.txt)

MicroDVD(*.sub/*.txt)

SubViewer 2.0(*.sub/*.txt)

TMPlayer(*.txt)

Dvd Subtitle System(*.txt)

VobSub (*.sub) b Sub/idx, stream based format.

Playable Codec format

"DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx ",

"MP43 ", "3IVX ".

Playable Audio format

"Dolby Digital ", "DTS ", "PCM ", "MP3 ", "WMA ".

• Sampling frequency: within 8 - 48 kHz (MP3),

within 22 - 48kHz (WMA)

• Bit rate: within 8 - 320kbps (MP3),

32 - 256kbps (WMA)

La page charge ...

LG DV298H-NH Le manuel du propriétaire

Marque: LG

Modèle: DV298H-NH

Catégorie: Lecteurs DVD

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: LG DV298H-NH Owner's manual

LG DV298H-NH Le manuel du propriétaire

LG DV298H-NH Le manuel du propriétaire

dans d''autres langues

Documents connexes