Generac iX2000 0057933 Manuel utilisateur

Marque: Generac

Modèle: iX2000 0057933

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

iX Series Digital Inverter

Portable Generator

Owner’s Manual

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

WWW.GENERAC.COM

1-888-GENERAC

(1-888-436-3722)

SAVE THIS MANUAL FOR FUTURE REFERENCE

000721

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

Table of Contents

Section 1 Introduction and Safety 1

Introduction ..................................... 1

Safety Rules .................................... 1

Safety Symbols and Meanings ........ 1

Exhaust and Location Hazards ....... 2

Electrical Hazards ........................... 2

Fire Hazards .................................... 3

Standards Index .............................. 3

Section 2 General Information and

Setup .............................................. 4

Know Your Generator ..................... 5

Emissions Information ..................... 5

Add Engine Oil ................................ 7

Fuel ................................................. 7

Section 3 Operation ...................... 8

Operation and Use Questions ......... 8

Before Starting Engine .................... 8

Prepare Generator for Use .............. 8

Know Generator Limits .................... 8

Transporting/Tipping of the Unit ...... 9

Using the FlexPower™ Switch ........ 9

Starting Pull Start Engines .............. 9

Low Oil Level Shutdown System ... 10

Using the 12 VDC Battery Charger 10

Section 4 Maintenance and

Troubleshooting ..........................11

Maintenance Recommendations ...11

Maintenance Schedule ..................11

Preventive Maintenance ...............11

Engine Maintenance ......................11

Inspect Muffler and Spark Arrester 12

Replace Fuel Filter ........................13

Storage ..........................................13

Troubleshooting .............................15

Notes .............................................16

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

Owner’s Manual for Portable Generator 1

Section 1 Introduction and Safety

Introduction

Thank you for purchasing a Generac Power

Systems Inc. product. This unit has been

designed to provide high-performance, effi-

cient operation, and years of use when main-

tained properly.

If any section of the manual is not understood,

contact your nearest Independent Authorized

Service Dealer (IASD), or contact Generac

Customer Service at 1-888-GENERAC (1-

888-436-3722), or www.generac.com with any

questions or concerns.

The owner is responsible for proper mainte-

nance and safe use of the equipment. Before

operating, servicing or storing this generator:

• Study all warnings in this manual and on

the product carefully.

• Become familiar with this manual and the

unit before use.

• Refer to the Assembly section of the man-

ual for instructions on final assembly proce-

dures. Follow the instructions completely.

Save these instructions for future reference.

ALWAYS supply this manual to any individual

that will use this machine.

THE INFORMATION CONTAINED HEREIN

WAS BASED ON MACHINES IN PRODUC-

TION AT THE TIME OF PUBLICATION. GEN-

ERAC RESERVES THE RIGHT TO MODIFY

THIS MANUAL AT ANY TIME.

Safety Rules

The manufacturer cannot anticipate every

possible circumstance that might involve a

hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, there-

fore, not all inclusive. If using a procedure,

work method or operating technique that the

manufacturer does not specifically recom-

mend, verify that it is safe for others. Also

make sure the procedure, work method or

operating technique utilized does not render

the equipment unsafe.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER,

WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions

about a particular operation that may be haz-

ardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are

as follows:

NOTE: Notes contain additional information

important to a procedure and will be found

within the regular text of this manual.

These safety warnings cannot eliminate the

hazards that they indicate. Common sense

and strict compliance with the special instruc-

tions while performing the action or service

are essential to preventing accidents.

Safety Symbols and Meanings

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

000657

DANGER

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is

a poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

2 Owner’s Manual for Portable Generator

• For safety reasons, it is recommended that

the maintenance of this equipment be per-

formed by an IASD. Inspect the generator

regularly, and contact the nearest IASD for

parts needing repair or replacement.

• Operate generator only on level surfaces

and where it will not be exposed to exces-

sive moisture, dirt, dust or corrosive vapors.

• When working on this equipment, remain

alert at all times.

• Never work on the equipment when physi-

cally or mentally fatigued.

• Never use the generator or any of its parts

as a step. Stepping on the unit can stress

and break parts, and may result in danger-

ous operating conditions from leaking

exhaust gases, fuel leakage, oil leakage,

etc.

Exhaust and Location Hazards

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. Seek medical

attention as you could have carbon monox-

ide poisoning.

Electrical Hazards

• The National Electric Code (NEC) requires

the frame and external electrically conduc-

tive parts of the generator be properly con-

nected to an approved earth ground. Local

electrical codes may also require proper

grounding of the generator. Consult with a

local electrician for grounding requirements

in the area.

• Use a ground fault circuit interrupter in any

damp or highly conductive area (such as

metal decking or steel work).

(000116)

DANGER

Electrocution. Turn utility and emergency

power supplies to OFF before connecting power

source and load lines. Failure to do so will result

in death or serious injury.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or fire.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

000406

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000179a)

DANGER

The exhaust system must be properly maintained. Do

not alter or modify the exhaust system as to render it

unsafe or make it noncompliant with local codes and/or

standards. Failure to do so will result in death

or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

Owner’s Manual for Portable Generator 3

Fire Hazards

• Do not operate the generator if connected

electrical devices overheat, if electrical out-

put is lost, if engine or generator sparks or if

flames or smoke are observed while unit is

running.

• Keep a fire extinguisher near the generator

at all times.

Standards Index

1. National Fire Protection Association

(NFPA) 70: The NATIONAL ELECTRIC

CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association

(NFPA) 5000: BUILDING CONSTRUC-

TION AND SAFETY CODE available from

www.nfpa.org

3. International Building Code available from

www.iccsafe.org

4. Agricultural Wiring Handbook available

from www.rerc.org, Rural Electricity

Resource Council P.O. Box 309 Wilming-

ton, OH 45177-0309

5. ASAE EP-364.2 Installation and Mainte-

nance of Farm Standby Electric Power

available from www.asabe.org, American

Society of Agricultural & Biological Engi-

neers 2950 Niles Road, St. Joseph, MI

49085

6. C22.2 100-14 Electric motors and genera-

tors for installation and use, in accordance

with the Rules of the Canadian Electrical

Code

This list is not all inclusive. Check with the

Authority Having Jurisdiction (AHJ) for any

local codes or standards which may be appli-

cable to your jurisdiction.

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Add fuel in a well

ventilated area. Keep fire and spark away. Failure to

do so will result in death or serious injury.

(000166)

DANGER

Do not overfill fuel tank. Fill to 1/2 in. of top of tank to

allow for fuel expansion. Overfilling may cause fuel to

spill onto engine causing fire or explosion, which will

result in death or serious injury.

(000174)

DANGER

Risk of fire. Allow fuel spills to completely dry

before starting engine. Failure to do so will

result in death or serious injury.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

4 Owner’s Manual for Portable Generator

Section 2 General Information and Setup

Figure 2-1. Features and Controls

TABLE 1. Generator Components

NOTE: Do not exceed the rated output of the

generator.

Figure 2-2. Control Panel

Figure 2-3. Unit Identification Label

000723

000721

1 Carrying Handle

2 Spark Plug Cover

3 Primer Bulb

4 Fuel Tank Cap

5 Control Panel

6Air Intake Slats

7 Muffler

8 Choke

9 Left Side Service Cover

10 Vent Hoses

11 Fuel Shut Off

12 Recoil Starter

13 Low Oil Level LED (yellow)

14 Overload LED (red)

15 Ready LED (green)

16 12 VDC Plug

17 FlexPower™ Switch

18 12 VDC Circuit Breaker

19 Grounding Lug

20 120 VAC Receptacle

000724

000722

Owner’s Manual for Portable Generator 5

Know Your Generator

Replacement owner’s manuals are available

at www.generac.com.

Emissions Information

The Environmental Protection Agency (EPA)

(and California Air Resource Board (CARB)

for generators certified to CA standards)

requires that this generator comply with

exhaust and evaporative emission standards.

Locate the emissions compliance decal on the

engine to determine generator standards and

warranty details. This generator is certified to

operate on gasoline. The emission control

system may include the following compo-

nents:

• Air Induction System

– Intake Manifold

– Air Cleaner

• Fuel System

– Carburetor

– Fuel Tank

–Fuel Cap

– Fuel Lines

– Evaporative Vent Lines

– Carbon Canister

• Ignition System

–Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold

– Muffler

– Pulsed Air Valve

– Catalyst

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

TABLE 2. Product Specifications

1600 Watt

Engine Type Single Cylinder, 4-Stroke

Engine Size 99cc

Starter Type Recoil

Fuel Capacity/Type

0.69 gal (2.6L) Unleaded

Oil Capacity 0.63 qt (0.6L)

Run time at 25% Rated Load 5.7 Hours

Spark Plug Type NGK BPR7HS

Spark Plug Gap .030 in (0.762 mm)

Dimensions L x W x H 22 x 12 x 18 in (55.8 x 30.4 x 45.7 cm)

Weight Lb/kg 43.5/19.7

Maximum AC Output 1600 W

Surge AC Output 1650 W

AC Volts 120 VAC

Rated AC Current 13.3 Amp

Frequency 60 Hz

THD 3.0%

Insulation Class Class B

Outlets 5-15R (2), 12 VDC (1)

DC Volts 12 VDC

Rated DC Current 5 Amp

6 Owner’s Manual for Portable Generator

2000 Watt (49 State)

Engine Type Single Cylinder, 4-Stroke

Engine Size 127cc

Starter Type Recoil

Fuel Capacity/Type

0.85 gal (3.2L) Unleaded

Oil Capacity 0.63 qt (0.6L)

Run time at 25% Rated Load 5.3 Hours

Spark Plug Type NGK BPR6ES

Spark Plug Gap .030 in (0.762 mm)

Dimensions L x W x H 22 x 12 x 18 in (55.8 x 30.4 x 45.7 cm)

Weight Lb/kg 49.6/22.5

Maximum AC Output 2000 W

Surge AC Output 2200 W

AC Volts 120 VAC

Rated AC Current 16.7 Amp

Frequency 60 Hz

THD 3.0%

Insulation Class Class B

Outlets 5-20R (2), 12 VDC (1)

DC Volts 12 VDC

Rated DC Current 5 Amp

2000 Watt (50 State)

Engine Type Single Cylinder, 4-Stroke

Engine Size 127cc

Starter Type Recoil

Fuel Capacity/Type

0.82 gal (3.1L) Unleaded

Oil Capacity 0.63 qt (0.6L)

Run time at 25% Rated Load 4.7 Hours

Spark Plug Type NGK BPR6ES

Spark Plug Gap .030 in (0.762 mm)

Dimensions L x W x H 22 x 12 x 18 in (55.8 x 30.4 x 45.7 cm)

Weight Lb/kg 49.6/22.5

Maximum AC Output 2000 W

Surge AC Output 2200 W

AC Volts 120 VAC

Rated AC Current 16.7 Amp

Frequency 60 Hz

THD 3.0%

Insulation Class Class B

Outlets 5-20R (2), 12 VDC (1)

DC Volts 12 VDC

Rated DC Current 5 Amp

TABLE 2. Product Specifications

Owner’s Manual for Portable Generator 7

Add Engine Oil

Add recommended engine oil as shown in the

following chart.

NOTE: Use petroleum based oil (supplied) for

engine break-in before using synthetic oil.

1. Place generator on a level surface.

2. Remove the Left Side Service Cover.

3. Remove oil fill cap (A) located on bottom

of engine crankcase. See Figure 2-4.

4. Add recommended engine oil. The full

level is the base of the threads in the filler

neck (B). DO NOT OVERFILL!

5. Replace oil fill cap and hand-tighten.

Figure 2-4. Add Engine Oil

Fuel

Fuel requirements are as follows:

• Clean, fresh, unleaded gasoline.

• Minimum rating of 87 octane/87 AKI (91

RON).

• Up to 10% ethanol (gasohol) is acceptable

(where available; non-ethanol-premium fuel

is recommended).

• DO NOT use E85.

• DO NOT use a gas oil mix.

• DO NOT modify engine to run on alternate

fuels. Stabilize fuel prior to storage.

1. Verify unit is OFF and cooled for a mini-

mum of two minutes prior to fueling.

2. Place unit on level ground in a well venti-

lated area.

3. Clean area around fuel cap and remove

cap slowly (A). See Figure 2-5.

4. Add recommended fuel to 2 inches below

top (B). Do not overfill. See Figure 2-5.

5. Install fuel cap.

Figure 2-5. Add Recommended Fuel

NOTE: Allow spilled fuel to evaporate before

starting unit.

IMPORTANT NOTE: It is important to pre-

vent gum deposits from forming in fuel

system parts such as the carburetor, fuel

hose or tank during storage. Alcohol-

blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which

leads to separation and formation of acids

during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine problems, the fuel system

should be emptied before storage of 30

days or longer. See the Storage section.

Never use engine or carburetor cleaner

products in the fuel tank as permanent

damage may occur.

(000135)

CAUTION

Engine damage. Verify proper type and quantity of

engine oil prior to starting engine. Failure to do so

could result in engine damage.

10W-30

SAE 30

Synthetic 5W-30

000729

000730

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000166)

DANGER

Do not overfill fuel tank. Fill to 1/2 in. of top of tank to

allow for fuel expansion. Overfilling may cause fuel to

spill onto engine causing fire or explosion, which will

result in death or serious injury.

000728

8 Owner’s Manual for Portable Generator

Section 3 Operation

Operation and Use Questions

Call Generac customer service at 1-888-GEN-

ERAC (1-888-436-3722) with questions or

concerns about equipment operation and

maintenance.

Before Starting Engine

1. Verify engine oil level is correct.

2. Verify fuel level is correct.

3. Verify unit is secure on level ground, with

proper clearance and is in a well ventilated

area.

Prepare Generator for Use

Know Generator Limits

Overloading a generator can result in damage

to the generator and connected electrical

devices. Observe the following to prevent

overload:

• Add up the total wattage of all electrical

devices to be connected at one time. This

total should NOT be greater than the gener-

ator's wattage capacity.

• The rated wattage of lights can be taken

from light bulbs. The rated wattage of tools,

appliances, and motors can be found on a

data label or decal affixed to the device.

• If the appliance, tool, or motor does not

give wattage, multiply volts times ampere

rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction

types, require about three times more watts

of power for starting than for running. This

surge of power lasts only a few seconds

when starting such motors. Make sure to

allow for high starting wattage when select-

ing electrical devices to connect to the gen-

erator:

1. Figure the watts needed to start the largest

motor.

2. Add to that figure the running watts of all

other connected loads.

The Wattage Reference Guide is provided to

assist in determining how many items the gen-

erator can operate at one time.

NOTE: All figures are approximate. See data

label on appliance for wattage requirements.

Table 3. Wattage Reference Guide

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000179a)

DANGER

The exhaust system must be properly maintained. Do

not alter or modify the exhaust system as to render it

unsafe or make it noncompliant with local codes and/or

standards. Failure to do so will result in death

or serious injury.

(000118)

DANGER

Risk of fire. Do not use generator without

spark arrestor installed. Failure to do so

could result in death or serious injury.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

Device Running

Watts

*Air Conditioner (12,000 Btu) 1700

*Air Conditioner (24,000 Btu) 3800

*Air Conditioner (40,000 Btu) 6000

Battery Charger (20 Amp) 500

Belt Sander (3") 1000

Chain Saw 1200

Circular Saw (6-1/2") 800 to 1000

*Clothes Dryer (Electric) 5750

*Clothes Dryer (Gas) 700

*Clothes Washer 1150

Coffee Maker 1750

*Compressor (1 HP) 2000

*Compressor (3/4 HP) 1800

*Compressor (1/2 HP) 1400

Curling Iron 700

*Dehumidifier 650

Owner’s Manual for Portable Generator 9

Transporting/Tipping of the Unit

Do not operate, store or transport the unit at

an angle greater than 15 degrees.

Using the FlexPower™ Switch

When the accessories connected to the gen-

erator are going to be used intermittently

(such as a hand drill), the FlexPower™ switch

can be pushed to the ON (I) position. This will

lower generator engine speed when loads are

not being applied, saving fuel, reducing

engine wear and extending runtime.

Starting Pull Start Engines

1. Unplug all electrical loads from the unit's

receptacles before starting engine.

2. Place generator on a level surface.

3. Turn the FlexPower Switch OFF (O).

4. Turn fuel valve to the ON. See Figure 3-6.

Figure 3-6.Fuel Valve ON

5. Press primer bulb (up to six (6) times). See

Figure 3-7.

Figure 3-7.Primer Bulb

6. Slide engine choke to Full Choke position

(right). See Figure 3-8.

Disc Sander (9") 1200

Edge Trimmer 500

Electric Blanket 400

Electric Nail Gun 1200

Electric Range (per element) 1500

Electric Skillet 1250

*Freezer 700

*Furnace Fan (3/5 HP) 875

*Garage Door Opener 500 to 750

Hair Dryer 1200

Hand Drill 250 to 1100

Hedge Trimmer 450

Impact Wrench 500

Iron 1200

*Jet Pump 800

Lawn Mower 1200

Light Bulb 100

Microwave Oven 700 to 1000

*Milk Cooler 1100

Oil Burner on Furnace 300

Oil Fired Space Heater (140,000

Btu)

400

Oil Fired Space Heater (85,000 Btu) 225

Oil Fired Space Heater (30,000 Btu) 150

*Paint Sprayer, Airless (1/3 HP) 600

Paint Sprayer, Airless (hand-held) 150

Radio 50 to 200

*Refrigerator 700

Slow Cooker 200

*Submersible Pump (1-1/2 HP) 2800

*Submersible Pump (1 HP) 2000

*Submersible Pump (1/2 HP) 1500

*Sump Pump 800 to 1050

*Table Saw (10") 1750 to 2000

Television 200 to 500

Toaster 1000 to 1650

Weed Trimmer 500

* Allow 3 times the listed watts for starting these

devices.

(000183)

WARNING

Recoil Hazard. Recoil could retract unexpectedly.

Kickback could result in death or serious injury.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

000725

000726

10 Owner’s Manual for Portable Generator

Figure 3-8.Choke Position

7. Firmly grasp recoil handle and pull slowly

until increased resistance is felt. Pull rap-

idly up and away.

8. When engine starts, move choke knob to

1/2-choke position until engine runs

smoothly, then to OFF position. If engine

falters, move choke back to 1/2-choke

position until engine runs smoothly, then to

OFF position.

NOTE: If engine fires, but does not continue to

run, move choke lever to Full Choke and

repeat starting instructions.

IMPORTANT NOTE: Do not overload the

generator. Also, do not overload individual

panel receptacles. If the Overload LED

(red) is lit attached devices stop operating,

stop engine. Reduce loads before restart-

ing engine. Read “Know Generator Limits”

carefully.

Generator Shut Down

1. Shut off all loads and unplug electrical

loads from generator panel receptacles.

2. Let engine run at no-load for several min-

utes to stabilize internal temperatures of

engine and generator.

3. Turn fuel valve to the OFF. See Figure 3-9.

Figure 3-9.Fuel Valve OFF

Low Oil Level Shutdown System

The engine is equipped with a low oil level

sensor that shuts down the engine automati-

cally when the oil level drops below a speci-

fied level. The engine will not run until the oil

has been filled to the proper level.

If the engine shuts down and there is sufficient

fuel, check engine oil level.

Using the 12 VDC Battery

Charger

The 12 VDC receptacle may be used to

recharge 12 VDC automotive batteries only.

The DC charging output is not regulated. The

circuit protector does not prevent over-

charging a battery.

1. Connect the charging cable to the genera-

tor first, then the battery. ALWAYS connect

the red lead to positive (+), and the black

to negative (-).

2. Keep the FlexPower™ switch in the OFF

(O) position.

3. Start generator and use as normal.

Charging time will vary with battery size

and condition. Check voltage at battery

terminals once the charging cable has

been unplugged, or generator has been

shut down.

NOTE: This receptacle cannot recharge 6 Volt

batteries and cannot be used to crank an

engine having a discharged battery.

000727

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

000725

(000137a)

WARNING

(000163)

WARNING

Risk of burn. Battery contains electrolyte solution

which can cause burns and blindness.

If electrolyte contacts skin or eyes, flush with

water and seek immediate medical attention.

(000138a)

WARNING

(000167)

CAUTION

Do not make battery connections

in reverse. Doing so will result in

equipment damage.

Owner’s Manual for Portable Generator 11

Section 4 Maintenance and Troubleshooting

Maintenance Recommendations

Regular maintenance will improve perfor-

mance and extend generator life. See a quali-

fied dealer for service.

Generator warranty does not cover items sub-

jected to operator abuse or negligence. To

receive full warranty value, operator must

maintain generator as instructed in this man-

ual, including proper storage as detailed in

Winter Storage and Long Term Storage.

NOTE: Call 1-888-GENERAC (1-888-436-

3722) with questions about component

replacement.

Maintenance Schedule

Follow maintenance schedule intervals,

whichever occurs first according to use.

NOTE: Adverse conditions will require more

frequent service.

NOTE: All required service and adjustments

should be each season as detailed in the fol-

lowing chart.

Preventive Maintenance

Dirt or debris can cause improper operation

and equipment damage. Clean generator

daily or before each use. Keep area around

and behind muffler free from combustible

debris. Inspect all cooling air openings on

generator.

• Use a damp cloth to wipe exterior surfaces

clean.

• Use a soft bristle brush to loosen caked on

dirt, oil, etc.

• Use a vacuum to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi)

may be used to blow away dirt. Inspect

cooling air slots and openings on generator.

These openings must be kept clean and

unobstructed.

NOTE: DO NOT use a garden hose to clean

generator. Water can enter engine fuel system

and cause problems. If water enters generator

through cooling air slots, some water will be

retained in voids and crevices of rotor and sta-

tor winding insulation. Water and dirt buildup

on generator internal windings will decrease

insulation resistance of windings.

Engine Maintenance

Engine Oil Recommendations

Add recommended engine oil as shown in the

following chart.

NOTE: Use petroleum based oil (supplied) for

engine break-in before using synthetic oil.

At Each Use

Check engine oil level

Every 100 Hours or Every Season*

Change oil ǂ

Clean air filter**

Every 6 Months

Check spark plug

Check muffler

Every Season

Replace spark plug

Replace fuel filter

Inspect/clean spark arrestor

ǂ Change oil after first 5 hours of operation,

then every season.

* Change oil and oil filter every month when

operating under heavy load or in high tem-

peratures.

** Clean more often under dirty or dusty oper-

ating conditions. Replace air filter parts if

they cannot be adequately cleaned.

(000142)

Do not insert any object through the air cooling slots.

Generator can start at any time and could result in

death, serious injury, and unit damage.

WARNING

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires

when working on unit. Failure to do so could result

in death or serious injury.

10W-30

SAE 30

Synthetic 5W-30

000729

12 Owner’s Manual for Portable Generator

Change Engine Oil

When using generator under extreme, dirty,

dusty conditions, or in extremely hot weather,

change oil more frequently.

NOTE: Don’t pollute. Conserve resources.

Return used oil to collection centers.

Change oil while engine is still warm from run-

ning, as follows:

1. Place generator on a level surface.

2. Remove the Left Side Service Cover.

3. Remove oil fill cap (A) located on bottom

of engine crankcase. See Figure 4-1.

4. Tip unit and drain oil completely into a suit-

able container.

5. Add recommended engine oil. The full

level is the base of the threads in the filler

neck (B). DO NOT OVERFILL!

6. Install oil fill cap, and finger tighten.

7. Wipe up any spilled oil.

8. Properly dispose of oil in accordance with

all applicable regulations.

Figure 4-1. Add Engine Oil

Air Filter

Engine will not run properly and may be dam-

aged if run with a dirty air filter. Service air fil-

ter more frequently in dirty or dusty conditions.

To service air filter:

1. See Figure 4-2. Remove the Left Side Ser-

vice Cover screw (A) and remove cover

(B).

2. Remove filter housing cover (C).

3. Remove air filter (D) and wash in soapy

water. Squeeze filter dry in clean cloth (DO

NOT TWIST).

4. Clean air filter cover before installing.

NOTE: To order a new air filter, contact the

nearest IASD at 1-888-GENERAC (1-888-

436-3722).

Figure 4-2. Air Filter Assembly

Service Spark Plug

To service spark plug:

1. Remove spark plug cover (A). See Figure

4-3.

2. Pull spark plug lead from spark plug (B).

3. Use a socket wrench and remove spark

plug.

4. Install new spark plug into cylinder head

and tighten to 15 ft/lb (20.3 Nm).

5. Replace the spark plug lead, making sure

it is fully seated.

6. Replace spark plug cover.

Figure 4-3. Spark Plug

Inspect Muffler and Spark

Arrester

NOTE: It is a violation of California Public

Resource Code, Section 4442, to use or oper-

ate the engine on any forest-covered, brush-

covered, or grass-covered land unless the

exhaust system is equipped with a spark

arrester, as defined in Section 4442, main-

tained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for exhaust system installed on this

engine.

NOTE: Use ONLY original equipment replace-

ment parts.

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires

when working on unit. Failure to do so could result

in death or serious injury.

000730

000731

000733

Owner’s Manual for Portable Generator 13

Inspect muffler for cracks, corrosion, or other

damage. Remove spark arrester, if equipped,

inspect for damage or carbon blockage.

Replace parts as required.

Inspect Spark Arrester Screen (50

State)

1. Remove clamp (A) and screen retainer

(B). See Figure 4-4.

2. Slide spark arrestor screens (C) out from

muffler outlet (D).

3. Inspect screens and replace if torn, perfo-

rated or otherwise damaged. Do NOT use

a defective screen. If screens are not dam-

aged, clean with commercial solvent.

4. Replace screens (C) and retainer (B) and

secure with clamp (A).

Figure 4-4. Spark Arrestor Screen

Replace Fuel Filter

Locate fuel filter just below engine intake

housing. See Figure 4-5. Make sure fuel shut-

off is OFF (O).

1. Remove the pinch clamps from fuel filter

(A) and pull hoses free.

2. Replace used filter.

3. Push fuel hoses onto barbed filter fittings

until they seat completely.

4. Replace clamps making sure they are

seated on the fittings.

Figure 4-5. Replace Fuel Filter

Storage

General

It is recommended to start and run the genera-

tor for 30 minutes, every 30 days. If this is not

possible, refer to the following list to prepare

unit for storage.

• DO NOT place a storage cover on a hot

generator. Allow unit to cool to room tem-

perature before storage.

• DO NOT store fuel from one season to

another unless properly treated.

• Replace fuel container if rust is present.

Rust in fuel will cause fuel system prob-

lems.

• Cover unit with a suitable protective, mois-

ture resistant cover.

• Store unit in a clean and dry area.

• Always store generator and fuel away from

heat and ignition sources.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

000735

(000168)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Keep fire

and spark away. Failure to do so will result

in death or serious injury.

000732

(000143)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Store fuel in a well

ventilated area. Keep fire and spark away. Failure

to do so will result in death or serious injury.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

14 Owner’s Manual for Portable Generator

Prepare Fuel System for Storage

Fuel stored over 30 days can go bad and

damage fuel system components. Keep fuel

fresh, use fuel stabilizer.

If fuel stabilizer is added to fuel system, pre-

pare and run engine for long term storage.

Run engine for 10-15 minutes to circulate sta-

bilizer throughout fuel system. Adequately

prepared fuel can be stored up to 24 months.

NOTE: If fuel has not been treated with fuel

stabilizer, it must be drained into an approved

container. See Figure 4-6. Run engine until it

stops from lack of fuel. Use of fuel stabilizer in

fuel storage container is recommended to

keep fuel fresh.

Figure 4-6. Carburetor Drain Valve

1. Change engine oil.

2. Remove spark plug.

3. Pour tablespoon (5-10cc) of clean engine

oil or spray a suitable fogging agent into

cylinder.

4. Pull starter recoil several times to distrib-

ute oil in cylinder.

5. Install spark plug.

6. Pull recoil slowly until resistance is felt.

This will close valves so moisture cannot

enter engine cylinder. Gently release

recoil.

Change Oil

Change engine oil before storage. See

Change Engine Oil.

000734

(000181)

WARNING

Vision Loss. Eye protection is required to avoid

spray from spark plug hole when cranking engine.

Failure to do so could result in vision loss.

Owner’s Manual for Portable Generator 15

Troubleshooting

PROBLEM CAUSE CORRECTION

Engine won't start. 1. No fuel in tank.

2. Fuel valve turned off.

3. Defective spark plug.

4. Plugged fuel filter.

5. Defective or stuck engine stop

switch.

1. Add fuel to tank.

2. Turn fuel valve on.

3. Replace spark plug.

4. Replace fuel filter.

5. Replace engine start switch.

Engine starts, then shuts

down.

1. Low fuel level.

2. Fuel tank vent closed.

3. Incorrect engine oil level.

4. Contaminated fuel.

5. Defective low oil level switch.

6. Defective ignition coil.

1. Add fuel to tank.

2. Open fuel tank vent.

3. Check engine oil level. Add or

drain as needed.

4. Replace fuel filter.

5. Replace low oil level switch.

6. Replace ignition coil.

Engine starts, then runs

rough.*

1. Choke is stuck or left on.

2. Dirty or clogged air filter.

3. Defective or dirty spark plug.

4. Dirty fuel filter.

5. Defective EcoMode switch.

1. Turn choke off.

2. Clean or replace the air filter

element.

3. Replace spark plug.

4. Replace fuel and fuel filter.

5. Replace EcoMode switch.

No AC output. 1. Generator overloaded (Over-

load LED is on and Ready

LED is flashing. See

Figure 2-

2).

2. AC voltage is low (Overload

LED is on and Ready LED is

flashing. See

Figure 2-2).

3. Inverter module overheated

(Overload LED is on and

Ready LED is flashing. See

Figure 2-2).

4. Short circuit in electrical

device (Overload LED is on

and Ready LED is flashing.

See

Figure 2-2).

5. Defective inverter assembly.

1. Shut down generator to reset

module. Reduce loads and

restart generator.

2. Verify the choke is OFF.

3. Verify service door is ON. Let

cool for 15 minutes and start

generator.

4. Check condition of extension

cords and items being pow-

ered.

5. Replace inverter assembly.

No DC output. ** 1. DC circuit breaker is open.

2. Defective DC circuit breaker.

3. Defective rectifier.

1. Reset DC circuit breaker.

2. Replace DC circuit breaker.

3. Replace rectifier.

Fuel leaks from drain

hoses.

1. Fuel system over primed

(flooded).

2. Carburetor drain in bowl is not

closed.

1. Let generator sit 15 minutes

before starting.

2. Turn valve clockwise to close.

* Engine speed increases and decreases — This is normal as the generator starts up and as loads

vary.

** Verify EcoMode Switch is OFF.

16 Owner’s Manual for Portable Generator

Notes

Owner’s Manual for Portable Generator 17

Part No. 0J9694 Rev. G 08/20/15

Printed in USA

reserved

Specifications are subject to change without notice.

No reproduction allowed in any form without prior

written consent from Generac Power Systems, Inc.

Generac Power Systems, Inc.

S45 W29290 Hwy. 59

Waukesha, WI 53189

1-888-GENERAC (1-888-436-3722)

generac.com

La page charge ...

Generac iX2000 0057933 Manuel utilisateur

Marque: Generac

Modèle: iX2000 0057933

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac iX2000 0057933 User manual
español: Generac iX2000 0057933 Manual de usuario

Autres documents

Honeywell 800 Watt Manuel utilisateur