WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73142
HARDWARE
CAUTION:
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or acces-
sories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in
personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or
missing.
MAINTENANCE NOTE:
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
Wire Connector
Qty: 4pcs
Mounting Screw
Qty: 1 Extra
A
B
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73142
PREPARATION
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the mounting back plate.
4. Secure the mounting back plate to the junction box using standard junction box screw that provided with the junction box.
Note: (i)Using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii)The side of the mounting plate marked “GND” must face out.
Note: retracting or extending excessive cable length through the cable gripper is not recommended.
b. Warning:
6. Please follow these recommendations if shortening the wire. Note or take a picture of how the wires are being connected and lable each
wire clearly. Using the Fig.3 and Fig 4 as given below as reference.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your
wire directly to the back plate using the “GND” screw provided. After wires are connected, tuck them carefully inside the junction box.
Fig. 1
Mounting Back plateFig. 2
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Junction Box Screw
Push up
Mounting Screw
B
Wire Connector
A
Junction Box
Ground Wire
9"
4 1/8”
1 3/4”
1 3/8”
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73142
COMPLETING THE INSTALLATION
Fig. 3
White - Neutral
Black - Hot
Red +
Black -
Center +
Bare -
Driver
Input
Output
Black - Hot
White - Neutral
Black -
Red +
Output
Input
Bare -
Center +
Center - To Driver+(Red)
Bare - To Driver-(Black)
30
8
Black -
+
Red
+
Red
Black -
White
- Neutral
White
- Neutral Black
- Hot
Black
- Hot
White
- Neutral
Black
- Hot
Input
Driver
Output
Input
Driver
Output
Fig. 4 PD-73142
Center - To Driver+(Red)
Bare - To Driver-(Black)
Center - To Driver+(Red)
Bare - To Driver-(Black)
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct.2021
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73155
HARDWARE
CAUTION: To prevent electrical shock, ensure electricity has been turned o at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or acces-
sories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could result in
personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or
missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un
chion humide.
Wire Connector
Qty: 4pcs
Mounting Screw
Qty: 1 Extra
A
B
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2021
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73155
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the mounting back plate.
4. Secure the mounting back plate to the junction box using standard junction box screw that provided with the junction box.
Note: (i)Using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii)The side of the mounting plate marked “GND” must face out.
5. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
a. Retract the wires close to a desireable length and tuck within the canopy before securing the xture in place.
Note: retracting or extending excessive cable length through the cable gripper is not recommended.
b. Warning: Shortening these cables without professional helps or electronic background is not advisable. Any modications
to the xture may result in voiding the warranty of the product.
6. Please follow these recommendations if shortening the wire. Note or take a picture of how the wires are being connected and lable each
wire clearly. Using the Fig.3 and Fig 4 as given below as reference.
CONNECTING THE WIRES (Fig. 2)
7. Connect the driver’s input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A) are secured. If your
outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the back plate using the “GND” screw provided. After wires are connected, tuck them carefully inside the junction box.
Fig. 1
Mounting Back plateFig. 2
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
13”
13/4”
13/8”
4 1/4”
Push up
Ground Wire
Junction Box
Wire Connector
Junction Box Screw
Mounting Screw
B
A
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2021
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION
731-LED Pendant
PD-73155
COMPLETING THE INSTALLATION
8. Secure the xture by mounting the canopy to the mounting back plate.Slide the canopy in the direction of the notch until
it latches in place. Secure the xture to the mounting back plate using the mounting screw (B).
Fig. 3
Center - To Driver+(Red)
Bare - To Driver-(Black)
White - Neutral
Black - Hot
Red +
Black -
Center +
Bare -
Driver
Input
Output
Black - Hot
White - Neutral
Black -
Red +
Output
Input
Bare -
Center +
Center - To Driver+(Red)
Bare - To Driver-(Black)
Center - To Driver+(Red)
Bare - To Driver-(Black)
30
8
Black -
+
Red
+
Red
Black -
White
- Neutral
White
- Neutral Black
- Hot
Black
- Hot
White
- Neutral
Black
- Hot
Input
Driver
Output
Input
Driver
Output
Fig. 4 PD-73155
-
1
-
2
-
3
-
4
-
5
-
6
WAC Lighting PD-73155 Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
WAC Lighting FM-37416 Mode d'emploi
-
-
-
-
-
-
-
-
-