INSTALLATION INSTRUCTIONS
COLORSCAPING HARDSCAPE LIGHT
7872/7822
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING.
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the national electrical code (nec)
and local regulations.
- When handling the xture, do not apply pressure to the leds. Hold the xture by the base only.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts
and/or accessories designated for use by WAC Lighting. Substitution of parts or accessories not designated for use with this
product by WAC Lighting could result in personal injury or property damage and will void the warranty. Failure to follow this
instruction may invalidate the UL/cUL listing of this fixture. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation UL/cUL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule
base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calificación
UL/cUL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
*Note: WAC Smart Transformer is required to power the fixture. (sold separately)
These instructions apply to the model(s) below:
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
Installation Accessories
INSTALLATION INSTRUCTIONS
COLORSCAPING HARDSCAPE LIGHT
7872/7822
7872
7822
Rotating Clip and Bracket
Qty: 1pcs
No. 4 Mounting Screw
Qty: 2pcs
Outdoor Rated Wire Nut
Qty: 2pcs
SLAB MOUNTING
1. Make sure the main power supply is turned off.
2. Use a masonry hammer and chisel to remove the coping stone above
the point of application (Fig.3).
3. Place the fixture in the desired position and mark where the wire will
be leading on the stone below. In addition, mark the location of the two
screw holes onto the stone below. Temporarily remove the fixture
(Fig.4).
4. Use an angle grinder with a diamond-tipped blade to cut a groove
along the wire marking. Make sure the groove is deep enough for the
wire to rest flush with the stone the slab is on (Fig.5).
Fig. 3
Fig. 4 Fig. 5
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
3
INSTALLATION INSTRUCTIONS
COLORSCAPING HARDSCAPE LIGHT
7872/7822
Wire Marking
Screw Hole Markings
DIRECT MOUNTING
I: Mount Horizontally
1. Remove the pre-installed slab mount bracket (Fig. 8).
a. Unscrew the bracket screws and pull out the light engine
from the slab mount bracket.
b. Push the lead wire out of the slab mount bracket.
c. Re-insert the lead wire back into the light engine.
2. Checking the required drill size for your flush mount plastic anchors
for No. 4 screws, use a hammer drill with a masonry bit to drill out two
holes at the screw locations.
NOTE: The depth of the hole should be slightly longer than the length of
the plastic anchor.
3. Place the flush mount plastic anchor in the hole, using the back of a
screwdriver to gently hammer it in (Fig. 9).
4. Replace the fixture and screw the No. 4 screw into the plastic anchor,
securing the fixture.
5. Lead the fixture wires downward and connect them to the landscape
wires connected to your transformer using the provided outdoor rated
wire nuts.
Fig. 8
Fig. 9
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
4
5. Checking the required drill size for your flush mount plastic anchors
for No. 4 screws, use a hammer drill with a masonry bit to drill out two
holes at the screw locations.
NOTE: The depth of the hole should be slightly longer than the length of
the plastic anchor.
6. Place the flush mount plastic anchor in the hole, using the back of a
screwdriver to gently hammer it in.
7. Replace the fixture and screw the No. 4 screw into the plastic anchor,
securing the fixture.
8. Connect the fixture wires to landscape wires connected to your
transformer using the provided outdoor rated wire nuts (Fig.6).
9. Replace the coping stone on top of the fixture, using block adhesive to
secure it in place (Fig.7).
Fig. 7
Fig. 6
INSTALLATION INSTRUCTIONS
COLORSCAPING HARDSCAPE LIGHT
7872/7822
CLIP MOUNTING (Rotation)
1. Remove the pre-installed slab mount bracket (Fig.10).
a. Unscrew the bracket screws and pull out the light engine from
the slab mount bracket.
b. Push the lead wire out of the slab mount bracket.
c. Insert the lead wire into the rotating clip & bracket
d. Re-insert the lead wire assembly back into the light engine.
2. Using the same screws, attach one rotating clip on each end of the
fixture (Fig.10).
3. Place fixture in the desired position and mark the location of the two
screw holes.
4. Checking the required drill size for your flush mount plastic anchors for
No. 4 screws, use a hammer drill with a masonry bit to drill out two holes at
the screw locations.
NOTE: The depth of the hole should be slightly longer than the length of
the plastic anchor (Fig. 11).
5. Place the flush mount plastic anchor in the hole, using the back of a
screwdriver to gently hammer it in.
6. Replace the fixture and screw the No. 4 screw into the plastic anchor,
securing the fixture.
7. Lead the fixture wires downward and connect them to the landscape
wires connected to your transformer using the provided outdoor rated
wire nuts.
8. In order to aim the fixture, loosen both screws on the clips, rotate and
aim the fixture around its axis that is shown in the diagram (Fig. 11). Fix
the location by tightening the screws on both ends.
Fig. 10
Fig. 11
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEP 2022
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
5
INSTALLATION INSTRUCTIONS
COLORSCAPING HARDSCAPE LIGHT
7872/7822
Light Engine Replacement: (Fig. 12)
1. Unscrew two bracket screws and keep them for later Installation.
2. Grab both ends of the light engine at the end slots with both hands
and pull the light engine out from wall.
3. Align the new light engine with the lead wire connector. Push the
light engine in firmly and lock it with the two bracket screws from step 1.
4. Turn on the light.
Fig. 12
No. 4
Screw
Plastic Anchor
(Supplied By
Others)
Bracket
Screw
Lead
Wire
-
1
-
2
-
3
-
4
-
5
WAC Lighting 7872 Mode d'emploi
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
WAC Lighting 5831 Mode d'emploi
-
-
WAC Lighting 1061-27SS Mode d'emploi
-
-
-
-
-
-
-