WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
1
WARNING
IMPORTANT: NEVER attempt to do any work without shutting o the electricity.
1. Read all instructions before installing.
2. System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
3. Place the wall switch in the “OFF” position.
4. Go to the main fuse box, or circuit breaker. Unscrew the fuse(s) or switch “OFF” the circuit breaker switch(es) that control the power to the
space that you are working on.
5. Risk of electric shock. Install all luminaires 10 feet (3.05m) or more from a pool, spa or fountain.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or
broken. Failure to follow this instruction may invalidate the UL listing of this xture.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements locaux.
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
- Toujours mettre le fusible ou le disjoncteur en position arrêt dans la pièce ou des travaux électriques sont prévus
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et ne les
utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation UL du luminaire.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal en la
posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni utilice
piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación UL esta lámpara.
INSTALLATION INSTRUCTIONS
Hornet Accent
5611
5611
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
2
STEP 1: DETERMINING THE LOCATION
1. Make sure your main power is o.
2. At the point of installation, mount the stake by placing a piece
of wood on the stake and hammering the wood. Hammer
till the bottom of the ring is ush with the ground. Mounting
StakeFixture WireWire SlotLight Fixture.
3. In the case of hard soil, dig a hole and place the stake in so that
the bottom of the ring is ush with the ground. Fill the rest of the
hole with the removed soil and pack it tight to secure the stake.
4. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
STEP 2: WIRING THE FIXTURE
*Note: Transformer is required to power the xture. (Sold Separately)
5. Cut the power supply wire from the transformer at the location of
the xture.
6. Separate the power supply wire into two individual wires by
lightly pulling on each side so that a couple inches are separated.
7. Strip o ½ inch of the insulating material from each wire and
connect one to each of the wires from the xture using the
outdoor rated direct burial wire nuts provided.
Wire Nut
Qty: 2 pcs
7EAC112201P3
Mounting Stake
Qty: 1 pcs
9000-ST9-BZ
Note:
To install multiple xtures, also connect the power supply wire of each
additional xture to the connection described in 7 of the previous
xture.
INSTALLATION INSTRUCTIONS
Hornet Accent
5611
Fixture
Mounting Stake
Wire Slot
Fixture Wire
TRANSFORMER
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
3
STEP 3: INSTALLING THE FIXTURE
8. Screw the xture onto the stake provided, leading the wire from
the xture through the wire slot in the stake.
9. If desired, bury your wire by digging a small trench. Close the
trench by applying an inward force to both sides of the trench.
10. Repeat steps for other xtures in the same electrical circuit.
11. Turn the main power supply back on and make sure the xtures
light up.
STEP 4: AIMING THE FIXTURE
1. Tilting: Loosen the joint screw and adjust the head of the xture
to the desired direction before retightening the screw.
2. Loosen the mounting knob and rotate the xture
3. to the desired position before retightening the knob.
STEP 5: BEAM ANGLE ADJUSTMENT:
1. Note the five pre-determined beam angles on the fixture
body: 20°, 35°, 45°, 60°, 70°
2. Slightly loosen the thumb screw. Do not remove the thumb
screw from the fixture.
3. Hold the fixture body and move fixture shroud in and out for
beam angle adjustment.
4. Tighten the thumb screw for fixed beam angle.
Note: To install multiple xtures, follow the diagram above.
INSTALLATION INSTRUCTIONS
Hornet Accent
5611
Transformer
Runs to
the next
fixture
Joint Screw
Locking Nut
Rotating
Tilting
Thumb Screw
Fixture Shroud
Beam Angle
Markings
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91761
4
1)Surface Mount Accessory:
The surface mount accessory is used to mount the xture to
a hard surface like wood or cement or as alternative to the
mounting stake.
Installation: Mount the accessory to a hard surface using No. 10
Philips head screws that are at least half an inch long. If mounting
on concrete or something similar, rst use a plastic anchor sized
for No. 10 screws. If mounting on a soft surface rst attach the
included spikes.
Create a route underneath the accessory for your wire to travel
through. Lead your wire through the created route and screw
your xture onto the surface mount accessory.
INSTALLATION INSTRUCTIONS
Hornet Accent
5611
2)Tree Mount Accessory:
The tree mount accessory is a way for xtures to be mounted on
the trunk or a branch of a tree while minimizing damage to the
tree.
Installation: Mark the screw hole locations at the point of
installation. Screw the provided screw bolts into the tree until
the unthreaded portion of the bolt meets the surface of the
tree. Screw a hexnut onto bolt until it hits the unthreaded area.
Place the tree mount bracket onto the bolts and secure using
additional hex nuts. Attach light xture and lead wire through the
bracket.
3)Extension Accessory:
Using extension rods and rod joiners, xtures can be mounted
away from a surface in any desired direction. Rods come in 5 sizes:
4 inches, 8 inches, 12 inches, 18 inches, and 24 inches. These rods
can be connected via either straight or 90-degree rod joiners.
Installation: Screw in a rod joiner into your mounting accessory.
Screw an extension rod to the other side of the rod joiner.
Continue to use rod joiners and extension rods until the xture is
in the desired position.
No. 10 Tapping Screws
Surface Mount Canopy
Removable Spikes
Fixture
Wood Screw Bolts
Hex Nuts
Tree Mount Junction Box
Hex Nuts
Fixture
Mounting Accessories
Rod Joiner
Extension Rod
90° Rod Joiner
Fixture
-
1
-
2
-
3
-
4
dans d''autres langues
Documents connexes
-
WAC Lighting 5821 Mode d'emploi
-
-
-
-
-
-
-
-
-