GE current LRXB Series Guide d'installation

Marque: GE current

Modèle: LRXB Series

Taper: Guide d'installation

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 1 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Installation Guide

IND668

Lumination® LED Luminaire

Installation Guide for Direct-Mount / Retrot / Frame-Kit

(LRXB Series)

BEFORE YOU BEGIN / AVANT DE COMMENCER

Read these instructions and IOTA ILB-CP instruction manual completely and carefully.

Wear work gloves to prevent dirt and oil from being transferred to the luminaire.

WARNING / AVERTISSEMENT

RISK OF FIRE OR ELECTRIC SHOCK

• Turn power o before inspection, installation or removal.

• Install this kit only in the lumiaires that has the construction

features and dimensions shown in the photographs

and/or drawings.

• Installation of this product requires a person familiar with the

construction and operation of the luminaire’s electrical system

and the hazard involved. If not qualied, do not attempt

installation. Contact a qualied electrician.

• To prevent wiring damage or abrasion, do not expose wiring

to edges of sheet metal or other sharp objects.

• Do not make or alter any open holes in an enclosure of

wiring or electrical components during kit installation.

• Installation requires input rating of the retrot kit to not

exceed the input rating of the luminaire.

RISQUES D’INCENDIE OU DE DÉCHARGES ÉLECTRIQUES

• Couper l’alimentation avant l’inspection, l’installation ou d’eectuer

de la maintenance

• N’ installer cette trousse que sur des luminaires qui ont les

caractéristiques de construction et les dimensions telles que montrées

sure les photographies et dessins présentés.

• Risque d’incendie ou d’électrocution. L’installation du product nécessite

la connaissance de la construction et le fonctionement de l’installation

électrique du luminaire. Contactez un(e) électricien(ne) qualié(e).

• Pour prévenir les dommages ou l’abrasion de ls électriques, ne pas

exposer les ls aux arêtes de pièce de tôlerie ou n’importe quels autres

objets tranchant.

• Ne pas percer ou altérer les trous d’un boitier contenant l ou composant

électrique durant l’installation.

• L’installation nécessite que la valeur nominale d’entrée du kit ne dépasse

pas la valeur nominale d’entrée du luminaire originale.

CAUTION / ATTENTION

• Fixture suitable for wet locations, covered ceiling

mount only.

• Fixture may fall down if not installed properly,

follow installation instructions.

• Wear appropriate Personal Protective Equipment (PPE)

during installation and maintenance.

• Use only UL certied wires, wire connectors,

minimum 18AWG, minimum rated 90°C.

• Les luminaires sont adaptés aux endroits humides et ne s’appliquent

qu’aux plafonds couverts.

• Le luminaire peut tomber s’il nest pas installé correctement, suivre les

instructions d’installation.

• Porter les Équipement de Protection Individuelle (EPI) adaptés lors de

l’installation et de l’entretien.

• N’utilisez que des ls et connecteurs approuvés par UL. Calibre minimum

18AWG (0.75mm2) et température minimale de 90°C.

Prepare Electrical Wiring FCC STATEMENT

Electrical Requirements

• The LED luminaire must be connected to

the mains supply according to its ratings

on the product label.

• Class 1 wiring should be in accordance

with NEC.

Grounding Instructions

• The grounding and bonding of the overall

system shall be done in accordance to

local electric code of the country where the

luminire is installed.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2)This device must

accept any interference received, including interference that may cause undesired operation.

CAN ICES-005(A)/ NMB-005(A)

Note: This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at their own expense.

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 2 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

Contents

1. Direct-Mount installation..............................................................................................................................................................................................2

2. Retrot Installation ..........................................................................................................................................................................................................5

3. Frame-kit/pan installation ............................................................................................................................................................................................6

1. Direct-Mount Installation

Luminaire Installation

Before installation, check the xture size and the diameter of ceiling

opening according to below Tab1.

Provided Components

The components have been properly packed to avoid damage

during transit. Inspect the components to conrm there is no

physical damage. Do not install damaged components.

Components List

• LRXB Fixture Kit

• Installation Instructions

Tab 1

Fixture

Size

Fixture

Type

Opening Size

in Ceiling (inch)

Fixture

weight (kg)

Suitable Ceiling

Max Thickness

4 Round 4.5~5.0 0.475 5/8″

6 Round 6.0~6.7 0.525 3/4″

8Round 7.8~8.8 0.615 1″

10 Round 10.2~11.2 1.260 1″

12 Round 12.2~13.2 1.410 1″

4 Square 4.5~5.0 0.600 5/8″

6 Square 6.0~6.8 0.700 3/4″

8 Square 8.0~9.0 0.870 1″

Round Square

NOTE: For 10’’ and 12’’ xtures, a suitable UL Listed frame-kit is

recommended to be used with the xture for installation safety.

Cut an access opening in the ceiling with the diameter listed in Tab 1,

and install the xture to the ceiling per the codes. Make sure the

ceiling can withstand the weight of the xture and the thickness of

ceiling be less than the list in Tab1.

Ensure the center of existing J-Box cover is visible through the access

opening, and the connections to the branch circuit supply are visible

through the access opening.

Ensure that the power to the unit is turned o. Use proper lockout/

tagout procedures. See g A.

Fig A

Fig B

J-Box cover

(not provided)

Access opening

cut by customer

Fixture

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 3 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

Connect the black, white, yellow/green leads from the conduit to the power-supply with UL listed wire

connectors according to the wiring diagram C2. Be sure all connection are made inside the existing J-Box.

Optional Dimmer: When connecting a dimming Controller, connect the violet (dimming+) and pink (dimming-)

wires to the violet and pink wires of the xture.

Note: Cap all unused dimming leads with wire nuts.

Note: Phase cut dimmers must be wired to the power feed “hot” line (L). For 0-10V and phase cut dimming

compatibility, please visit: www.gecurrent.com/dimming

Select Lumen (8” luminaires with 3000lm are not

lumen selectable):

Fig D1 Fig D2

Fig D2

WIRING DIAGRAM C2

0–10 VOLT DIMMING

LRX

Fixture

To 0–10V

Dimmer

LED

Driver

Ground

Black

Pink

Violet

White

0–10V−

0–10V+

Green / Yellow

1000/650lm luminaires 1800/1000/650lm luminaires

Lumen Switch Lumen Switch

NOTE: For 1800/1000/650lm luminaires, the default

lumen is 1000lm. Push the switch up to activate 650lm.

Push the switch down to activate 1800lm. See g D2.

Fig C1

Conduit from

xture

Power Supply (not provided)

UL listed connectors

(not provided)

J-Box

(not provided)

Ceiling opening

NOTE: For 1000/650lm luminaires, the default

lumen is 1000lm. Push the switch down to activate

650lm. See g D1.

NOTE: For 4000/5000/6000lm luminaires, the default

lumen is 6000lm. Push the switch left to activate

4000lm and 5000lm respectively.

See g D3.

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 4 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

Select CCT

Fig E1

Fig E3 Fig E4

Fig E5

Fig F

Fig E2

2700K/3500K/3000K luminaires 3500K/4000K/5000k luminaires

CCT Switch

Switch Cover

CCT Switch plug

CCT Switch

Lumen Switch

CCT Switch

NOTE: For 3500K/4000K/5000K luminaires, the

default CCT is 4000K. Push the switch up to activate

3500K, push the switch down to activate 5000K.

See g E2 or E4.

NOTE: For 10in and 12in xtures, the CCT switch is

located on the housing sealed by a plug, and the

cover of the lumen switch can be used as a tool to

select lumen and CCT. See g E4.

NOTE: The cover of the lumen/CCT switches can

be used as a tool to select lumen and CCT.

See g E3.Place the switch cover back after lumen

and CCT setting.

Load springs into upright position by twisting the

springs upward and carefully insert the xture into

ceiling opening. The springs will rotate back into

position and hold the xture tight to the ceiling.

ONLY FOR 10IN AND 12IN FIXTURES: The CCT

switch plug must be placed back after CCT selection to

avoid light leakage and dust/bug ingress. See g E5.

ATTACH THE SAFETY TETHER TO THE

RECOMMENDED FRAME-KIT FOR REDUNDANT

INSTALLATION SAFETY.

NOTE: For 2700K/3000K/3500K luminaires, the de-

fault CCT is 3500K. Push the switch up to activate

2700K, push the switch down to activate 3000K.

See g E1 or E4.

CAUTION/ATTENTION

RISK OF PERSONAL INJURY - Operators shall ensure no

appendages are in the path of the torsion springs as they

are a pinch hazard when released. The springs will release

when the arm is exed downward. Be cautious that no body

part is in the path of the spring when released.

RISQUE DE BLESSURE CORPORELLE - Les techniciens

veilleront à ce qu’aucun appendice ne se trouve sur le

chemin des ressorts de torsion, car ils présentent un rique

de pincement lorsqu’ils sont libérés. Les ressorts seront

libérés au moment de échir le bras vers le bas. Faites attention

à ce qu’aucune partie du corps ne se trouve sur le chemin du

ressort à sa libération.

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 5 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

2. Retrot Installation

Luminaire Installation

Before installation, verify that the existing junction box

and frame-kit are metal construction, designed similarly

to g 2.

Note: Installers should examine all parts that are not

intended to be replaced by the retrot kit for damage

and replace any damaged parts prior to installation of

the retrot kit.

Fixture

Size

Fixture

Type

Existing Bracket

Hole Size (inch)

4 Round 4.5~5.0

6 Round 6.0~6.7

8Round 7.8~8.8

10 Round 10.2~11.2

12 Round 12.2~13.2

4 Square 4.5~5.0

6 Square 6.0~6.8

8 Square 8.0~9.0

Fig 2

Fig 2A

Fig 2B

Fig 2C

Ensure that the power to the unit be turned o.

Use proper lockout/tagout procedures.

Remove existing lamps, xture and ballast.

Leave wiring in junction box. Verify that the

AC supply line is provided with a ground

wire connected to the luminaire. See g 2B.

Connect conduit end with input leads to existing

J-Box and make the proper connections according

to diagram C1/C2.

Make all electrical connections sing UL Listed

wire connectors.

Securely close J-Box after wiring. See g 2C.

gecurrent.com/lumination

change without notice. All values are design or typical values when measured under laboratory conditions.

Page 6 of 7

Rev. September 9, 2022

IND668-Lumination-LRXB_Series-LED_Luminaire-Retroﬁt_

and_New_Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

About selecting CCT or lumen level, refer to

step D and E on page 3 and 4.

Load springs into upright position by twisting the

springs upward and carefully insert the xture to

ceiling opening.

The springs will rotate back into position and hold

the xture tight to the ceiling .

Only for 10 in and 12 in:

ATTACH THE SAFETY TETHER TO THE FRAME KIT

FOR REDUNDANT INSTALLATION SAFETY.

See g 2E.

WIRING DIAGRAM C1

0–10 VOLT DIMMING

LRX

Fixture

To 0–10V

Dimmer

LED

Driver

Ground

Black

Pink

Violet

White

0–10V−

0–10V+

Green / Yellow

Optional Dimmer: Optional Dimmer: When con-

necting a dimming controller, low-voltage dimming

wires must route through a separate knockout.

Connect the violet (dimming+) and pink (dimming-)

wires to the violet and pink wires of the xture.

Note: Cap all unused dimming leads with wire nuts

Note: Phase cut dimmers must be wired to the

power feed “hot” line (L). For 0-10V and phase cut

dimming compatibility, please visit:

www.gecurrent.com/dimming

CAUTION/ATTENTION

RISK OF PERSONAL INJURY - Operators shall ensure no

appendages are in the path of the torsion springs as they

are a pinch hazard when released. The springs will release

when the arm is exed downward. Be cautious that no body

part is in the path of the spring when released.

RISQUE DE BLESSURE CORPORELLE - Les techniciens

veilleront à ce qu’aucun appendice ne se trouve sur le

chemin des ressorts de torsion, car ils présentent un rique

de pincement lorsqu’ils sont libérés. Les ressorts seront

libérés au moment de échir le bras vers le bas. Faites attention

à ce qu’aucune partie du corps ne se trouve sur le chemin du

ressort à sa libération.

Fig 2E

Fig 2F

3. New Construction Installation

Provided Components

The components have been properly packed to avoid damage during transit. Inspect the components to conrm

there is no physical damage. Do not install damaged components. See Fig 3A and Tab 3.

gecurrent.com/lumination

reserved. GE and the GE monogram are trademarks

of the General Electric Company and are used

under license. Information and speciﬁcations

subject to change without notice. All values are

design or typical values when measured under

laboratory conditions.

droits réservés. GE et le monogramme GE sont des

marques déposées de General Electric Company et

sont utilisés sous licence. Les informations fournies

sont sujetes à modiﬁcations sans préavis. Toutes

les valeurs données sont théoriques ou typiques

lorsque mesurées sous conditions de laboratoire.

GE son marcas registradas de la General Electric

Company y se utilizan bajo licencia. La información

proporcionada está sujeta a cambios sin previo aviso.

Todos los valores son de diseño o valores típicos

cuando se miden en condiciones de laboratorio.

Page 7 of 7

Rev. September 9, 2022

IND668-Lumination-

LRXB_Series-LED_Luminaire-

Retroﬁt_and_New_

Construction-Install-Guide

Lumination® (LRXB - Series) Installation Guide

2 3 4 5

Tab 3

Provided Item Qty.

1Frame (4-inch, 6-inch, 8-inch, 10-inch or 12-inch) 1

2 Mounting Brackets 2

3 L-Bracket 2

5Wing Nut 3

Fixture

Diameter

Hole

Diameter

RX6 5.9–6.5 in.

RX8 7.6–8.2 in.

L-brackets

Mounting brackets

Place side L-brackets on existing

frame screws and tighten with

screwdriver on both sides of the

frame. Then attach mounting

brackets to both L-brackets with

wing nuts (provided).

Cut an appropriate hole on the

ceiling tile according to Tab 4.

Ensure the ceiling hole diameter

match the frame opening diameter.

Fixture

Diameter

Hole

Diameter

RX6 5.9–6.5 in.

RX8 7.6–8.2 in.

L-brackets

Mounting brackets

Slide hanger bars

(order separately)

through adjustable

mounting brackets.

Mounting brackets could also be

xed on the short side of frame.

Bars Conduit

A B

Adjust height and

tighten wing nut

Option A: Mount xture by attaching

hanger bars to T-Grid ceiling

(BH3 SKU 94890).

Option B: Mount xture with ½” EMT

conduit. (Not Supplied)

Bars Conduit

A B

Adjust height and

tighten wing nut

Adjust xture height to be ush with

ceiling and tighten both mounting

bracket wing nuts.

Refer to steps C-F of the retrot installation above to nish the installation.

A B C

D E F

Frame Installation

Tab 4

Fixture

Size

Fixture

Type

Suitable

Frame

Suitable Ceiling

Max Thickness

4 Round FRAME4R 5.0~5.5

6 Round FRAME6R 6.6~7.1

8Round FRAM8R 8.2~8.7

10 Round FRAME10R 10.6~11.2

12 Round FRAME12R 12.5~13.3

4 Square FRAME4S 5.1~5.6

6 Square FRAM6S 6.9~7.4

8 Square FRAME8S 8.5~9.4

Fig 3A

Access Opening

J-Box Cover

Saw

GE current LRXB Series Guide d'installation

Marque: GE current

Modèle: LRXB Series

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE current LRXB Series Installation guide

GE current LRXB Series Guide d'installation

GE current LRXB Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents