ReVent RVS130 Guide d'installation

Installation Guide

Read and Save These Instructions

Watch the installation video at:

reventfans.com

Questions? Call

1-877-543-8698 (English) or

1-800-615-5439 (French)

models

RVS130, RVS150

Need Help?

English

1

Table of Contents

Please Read and Save

These Instructions

page 1

page 1-2

page 3

page 4

page 5

page 6

page 7

page 8-13

page 13-18

page 18

page 19

page 20

Table of Contents

Specifications

What’s Inside The Box

Safety Information

Planning Your Installation

Connecting The Duct

Removing Your Old Fan

SheetLock® Easy Roomside Installation

Installation For New Construction Framing

Care And Cleaning

Frequently Asked Questions

3-Year Limited Warranty

...............

...........

...............

..........

........

.............

2

RVS150

Voltage

Frequency

Fan Weight

Shield Size

Housing Length*

Housing Width*

Housing Depth*

120 V

60 Hz

8.6 Lbs ( 3.9 Kg )

13 3/8 x 13 3/8 in ( 34 x 34 cm )

10 1/2 in ( 26.7 cm )

6 3/4 in ( 17.1 cm )

*This may require modification of your current opening. Some hand

tools required. Power tools may also be necessary.

RVS130

Voltage

Frequency

Fan Weight

Shield Size

Housing Length*

Housing Width*

Housing Depth*

120 V

60 Hz

8.6 Lbs ( 3.9 Kg )

13 3/8 x 13 3/8 in ( 34 x 34 cm )

10 1/2 in ( 26.7 cm )

6 3/4 in ( 17.1 cm )

*This may require modification of your current opening. Some hand

tools required. Power tools may also be necessary.

Specifications

performance at 6" ducting

Duct

Size

6 in

Energy

(watts)

32.2

30.8

Static Pressure

(in wg)

0.1

0.25

Airow

(cfm)

130

91

Sound

(sones)

0.9

performance at 6" ducting

Duct

Size

6 in

Energy

(watts)

37.5

36.7

Static Pressure

(in wg)

0.1

0.25

Airow

(cfm)

150

116

Sound

(sones)

1.3

3

What’s Inside The Box

MANUAL

Qty:1

TEMPLATE

Qty:1

TRIM RING

Qty:1

FAN

Qty:1

6” DAMPER

Qty:1

SHIELD

Qty:1

Installation Guide

Read and Save These Instructions

Watch the installation video at:

reventfans.com

Questions? Call

1-877-543-8698 (English) or

1-800-615-5439 (French)

models

RVS130, RVS150

Need Help?

English

SHORT BRACKET

Qty:2

LONG BRACKET

Qty:1

ROUNDHEAD

WOOD SCREW

Qty:6

#8 x 3/8" BRACKET

SECURING SCREW

Qty:3

WIRE NUT

Qty:3

USED FOR NEW CONSTRUCTION ONLY

4

Safety Information

1.) WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards, including fire-rated

construction.

b) Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer's guideline and safety standards,

such as those published by the National Fire Protection Association (NFPA), the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked as

appropriate for the application and be connected to a GFCI (Ground Fault Circuit

Interrupter) - protected branch circuit.

2.) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

3.) Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

4.) This ventilation fan is approved for use over a bathtub or shower when installed

in a GFCI protected circuit. Do not use unapproved fans over a bathtub or shower

that are not approved for that application.

5.) Install ductwork in a straight line with minimal bends.

6.) Use 120 V, 60 Hz for the electrical supply and properly ground the unit. Follow

all local safety and electrical codes.

7.) Do not use this fan with any solid-state control device; such as a dimmer switch.

Solid-state controls may cause harmonic distortion, which can cause a motor

humming noise, as well as increase risk of fire or electric shock.

8.) To reduce the risk of fire or electric shock, do not block air entry shield.

9.) Mount with the lowest moving parts at least 8.2 ft (2.5 m) above floor or grade

level.

10.) Never place a switch where it can be reached from a tub or shower.

11.) Type IC for use in direct contact with thermal insulation not to exceed R-50.

12.) Not for use in cooking areas. (See PAGE 5 for details)

13.) This product must properly connect to the grounding conductor of the supply

circuit.

Follow the heating equipment manufacturer’s guideline and safety standards, such

as those published by the National Fire Protection Association (NFPA), the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

WARNING: Not suitable for use as a range hood.

CAUTION: For General Ventilating Use Only - Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors.

CAUTION: Do not install in locations where the temperature will exceed

104°F (40°C).

IMPORTANT: Exercise care to not damage existing wiring when cutting or

drilling into walls or ceilings.

NOTE: Make sure duct work size is a minimum of the discharge. Do not

reduce. Reducing the duct size can increase fan noise.

IMPORTANT: You may want to consult with a qualified licensed electrician

regarding the wiring of your ventilation fan.

WARNING: To reduce the risk of electric shock, please disconnect the

electrical supply circuit before servicing.

CAUTION: This product must be properly grounded.

Go to reventfans.com to obtain a copy of this manual.

5

NOTE: If installing in existing construction, you may need to have access to

space above and below the installation location.

Cooking Area

do not install above or

inside this area

Cooking

Equipment Floor

Turning angle too sharp

Too many elbows

Avoid duct shrink

Elbow near the body

Fan

Body

Minimum 18 in ( 45.72 cm )

Planning Your Installation

When installing the ventilation fan in a new construction site, install the main body

of the FAN and duct work during the rough-in construction of the building. The

SHIELD should be installed after the finished ceiling is in place.

When installing in existing construction, use the provided cutout TEMPLATE for the

ceiling. SHIELD edge should overlap finished ceiling.

Not for use in cooking area - see diagram below.

Do not install ventilation fan in areas where the duct work will require configuration

as shown.

There are multiple installation configurations possible for this ventilation fan. Not all

configurations are shown. If your installation requires a variation other than those

shown, consult with a licensed contractor to determine the best installation for your

project. If you are replacing an existing fan, ensure that the new FAN will

adequately cover the existing opening.

Connecting the Duct

● Install a circular duct to outlet and secure it with duct tape or clamps.

● Install the duct to the outlet with a gradient 1°~2° to the outside as shown.

● The ducting from this FAN to the outside of the building has a strong effect on

● the air flow, noise and energy use of the fan. Use the shortest, straightest duct

● routing possible for best performance, and avoid installing the FAN with smaller

● ducts than recommended. Insulation around the ducts can reduce energy loss

● and inhibit mold growth. Fans installed with existing ducts may not achieve their

● rated airflow.

● 6 in (15.24 cm) round is recommended for best performance.

● Ensure duct joints and exterior penetrations are sealed with caulk or other

● similar material to create an air-tight path, to minimize building heat loss and

● gain, and to reduce the potential for condensation.

● Place/wrap insulation around duct and/or FAN in order to minimize possible

● condensation buildup within the duct, building heat loss and gain.

6

INSULATION*

(Place around and

over Fan Housing.)

Seal gaps

around

housing.

ROUND

DUCT*

POWER

CABLE*

Seal duct

joints with

tape.

FAN

HOUSING

ROUND

ELBOWS*

ROOF CAP*

(with built-in

damper)

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

*Purchase

separately.

OR

7

Removing Your Old Fan

1.) Disconnect the electrical power supply and lock out the service

panel for the existing fan.

2.) Remove the grille from the existing fan. Pull the grille down to expose it’s two

springs. Squeeze each spring together and pull down again to release the springs

from the motor plate slots.

3.) Your existing fan may be attached in several ways. Look for attachment screws

in the ceiling and remove. Your fan may also be attached on the attic side, which

will require you to access it from the attic. Locate attic attachment screws and

remove. Fan removal can be the most difficult step, please watch this video:

reventfans.com/how-to-remove-an-old-bath-fan

4.) Remove the old fan. This may require cutting and pulling. Wear gloves and

eye protection.

8

1.) Place the provided sheetrock cutout TEMPLATE on ceiling where you wish the

FAN to be (DAMPER and electrical positions shown on TEMPLATE). We suggest

using painter’s masking tape to hold the template in place while cutting. If there is a

pre-existing fan opening, use aligning windows to find it’s edges. Either cut through

the provided guide slots in the TEMPLATE, or mark your cut lines with a pencil and

remove the TEMPLATE. Use a sheetrock jab saw to cut your fan opening in the

ceiling.

SheetLock® Easy Roomside

Installation

Watch the video: reventfans.com

WARNING: Disconnect all AC Power Breakers or Fuses before attempting

to cut into your ceiling.

2.) Use a flathead screwdriver to raise the DAMPER away from the notch in the

FAN body, then slide the DAMPER up half way until the notch in the side of the

DAMPER aligns with the upper set of guides. Remove the DAMPER from the FAN.

Remove

DAMPER

from FAN

at notch

flathead

screwdriver

FAN

DAMPER

notch

guide

TEMPLATE

sheetrock jab saw

guide

9

4.) Attach conduit with wiring to FAN.

conduit

FAN

6.) Select a set of holding tabs, depending on the thickness of your sheetrock.

5/8 in (1.6 cm)

holding tab

1/2 in (1.3 cm)

holding tab

final securing tab 5/8 in (1.6 cm)

holding tab

1/2 in (1.3 cm)

holding tab

5.) Reattach DAMPER to FAN inside the ceiling, damper should click into place

securely.

ducting

conduit

DAMPER

FAN

3.) Attach DAMPER to ducting. Tape DAMPER to ducting with duct tape. Set the

connected DAMPER and ducting in the ceiling opening, then set the FAN in the

ceiling opening as well.

ceiling

ducting

Connect DAMPER and

ducting with duct tape

Place FAN and DAMPER

inside CEILING opening

ceiling

FAN

DAMPER

10

7.) Bend the holding tabs you selected outward.

9.) Disconnect FAN motor from electrical enclosure. Remove the electrical cover

set screw and slide open the electrical enclosure.

remove set

screw

unplug fan

connector

slide

WARNING: Disconnect the AC power before any work is done to any part of

the circuit ReVent® is connected to. If you do not understand this warning,

seek the services of a qualified licensed electrician.

WARNING: Copper to copper only. Do not use aluminum wire.

WARNING: Follow all local electrical and safety codes, and NEC (National

Electrical Codes).

CAUTION: If your house wires do not match these colors, determine what

each house wire represents before connecting. You may need to consult a

qualified licensed electrician to determine this safely.

8.) Set FAN into place in the opening using holding tabs, now the tabs hold the fan

in position in the ceiling opening.

holding tab

11

10.) Connect wiring using the provided WIRE NUTS. Match wire colors as shown:

line

ground

FAN

ground

housing

ground

line in

neutral

line in

FAN

fan switch

(purchased separately)

SWITCH NOT INCLUDED, MUST BE PURCHASED SEPARATELY

Always follow all safety instructions included with the switch you purchase. Do not

exceed maximum electrical ratings.

ReVent® fan

120V line AC

white

ground

fan

black

The FAN wires

cannot be

connected to a

dimmer switch

WIRE NUT

Qty:3

12

12.) Press and bend the final securing tabs flat against ceiling to lock the FAN in

place.

final securing tabs

13.) Align TRIM RING notch to vent (DAMPER) position. Attach TRIM RING to

FAN. TRIM RING attaches to FAN body and clicks into place when secure.

sheetrock

(ceiling)

apply even

pressure to

each side of

securing tab

11.) Once connected, reattach the electrical enclosure.

reattach set

screw

plug in fan

connector

slide

ceiling

TRIM RING

FAN

final securing tabs

notch

13

ceiling

mounting springs

FAN

TRIM RING

spring guide

SHIELD

14.) Attach the SHIELD by squeezing the mounting springs together and inserting

the springs into the spring guides in the FAN.

Installation For New

Construction Framing

WARNING: Disconnect all AC Power Breakers or Fuses before attempting

to cut into your ceiling.

1.) Select a set of holding tabs, depending on the thickness of your sheetrock.

2.) Bend the holding tabs you selected outward.

5/8 in (1.6 cm)

holding tab

1/2 in (1.3 cm)

holding tab

final securing tab 5/8 in (1.6 cm)

holding tab

1/2 in (1.3 cm)

holding tab

NOTE: Even with new construction, you can use the SheetLock® installation

method; however, ReVent® can still be installed using a method home

builders would be more familiar with, as outlined in this section.

14

4.) Attach conduit with wiring to FAN.

conduit

DAMPERFAN

5.) Attach DAMPER to ducting.

Attach DAMPER to

ducting with duct tape

framing joist

FAN

SHORT

BRACKET

(can be

cut down)

framing joist

SHORT

BRACKET LONG

BRACKET

conduit

3.) Attach FAN to ceiling joists with BRACKETS using ROUNDHEAD WOOD

SCREWS, then install the sheetrock for your ceiling.

ducting

#8 x 3/8"

BRACKET

SECURING

SCREW

Qty:3

conduit

ROUNDHEAD

WOOD SCREW

Qty:6

(use 2 per

bracket)

15

6.) Disconnect FAN motor from electrical enclosure. Remove the electrical cover

set screw and slide open the electrical enclosure.

remove set

screw

unplug fan

connector

slide

WARNING: Disconnect the AC power before any work is done to any part of

the circuit ReVent® is connected to. If you do not understand this warning,

seek the services of a qualified licensed electrician.

WARNING: Copper to copper only. Do not use aluminum wire.

WARNING: Follow all local electrical and safety codes, and NEC (National

Electrical Codes).

CAUTION: If your house wires do not match these colors, determine what

each house wire represents before connecting. You may need to consult a

qualified licensed electrician to determine this safely.

7.) Connect wiring using the provided WIRE NUTS. Match wire colors as shown:

line

ground

FAN

ground

housing

ground

line in

neutral

line in

FAN

FAN WIRE NUT

Qty:3

16

8.) Once connected, reattach the electrical enclosure.

SWITCH NOT INCLUDED, MUST BE PURCHASED SEPARATELY

Always follow all safety instructions included with the switch you purchase. Do not

exceed maximum electrical ratings.

reattach set

screw

plug in fan

connector

slide

fan switch

(purchased separately)

ReVent® fan

120V line AC

white

ground

fan

black

The FAN wires

cannot be

connected to a

dimmer switch

17

9.) When sheetrock is in place, press and bend the final securing tabs flat against

ceiling to lock the FAN in place.

final securing tabs

sheetrock

(ceiling)

apply even

pressure to

each side of

securing tab

10.) Align TRIM RING notch to vent (DAMPER) position. Attach TRIM RING to

FAN. TRIM RING attaches to FAN body and clicks into place when secure.

ceiling

TRIM RING

FAN

final securing tabs

notch

18

Care and Cleaning

ceiling

mounting springs

FAN

TRIM RING

spring guide

SHIELD

11.) Attach the SHIELD by squeezing the mounting springs together and inserting

the springs into the spring guides in the FAN.

WARNING: To reduce the risk of electric shock, fire, or injury to persons,

disconnect or turn off the breaker and lock the power supply at the panel to

prevent the power from being turned on before servicing or cleaning the unit.

1.) Remove the SHIELD by squeezing the springs and pulling down.

2.) Remove dust and dirt from the FAN with a vacuum cleaner.

3.) Dampen cloth with dish detergent. Wipe the FAN and dry with a cloth.

4.) Replace the SHIELD.

19

Frequently Asked Questions

Q: How do I clean my FAN?

A: It’s important to clean the SHIELD cover from time to time. Dust particles can

build up on the SHIELD. See PAGE 18 for care and cleaning instructions.

Q: What is CFM?

A: CFM is a measurement of air movement (cubic feet per minute). The higher the

CFM, the more air movement.

Q: What is a sone?

A: Sone is the rating used to describe the sound level. The lower the sone the

quieter the fan. A sone is not a decibel. Fans around 1 sone or less are considered

quiet while fans around 2 sones or more are considered loud.

Q: Can I install my bathroom ventilation FAN directly over a bathtub or shower?

A: Yes, but your FAN must be rated for over a shower/bath installation (all ReVent

models are) and must be on a GFCI protected circuit. Consult a qualified licensed

electrician about ground fault protected safety circuits.

Q: Do I have to vent my FAN to the outside?

A: Yes. All spot ventilation fans must be vented to the outside. Follow your local

code and consult it for advice. See PAGE 6 for national venting installation

suggestions and guidelines.

Q: Why do the windows and mirrors fog even when the FAN is running?

A: If windows and mirrors are very cold, condensation can still form on those

surfaces. If the bathroom is sealed tightly, replacement air may not be entering the

room fast enough to displace moist air. You need a gap under the bathroom

entrance door to allow air to enter the bathroom. If your home uses 3 inch diameter

ducting, upgrading the duct pipe to 4 inch diameter can greatly increase the airflow.

The vent pipe length should be 10 feet or less with minimal bends (See PAGE 6).

Ensure that the vent pipe is not blocked.

Q: My FAN is operating, but the air is moving slower than normal.

A: Check for obstructions in the ductwork. A common problem is debris blocking the

roof cap or outside wall vent. Older homes may have 3 inch diameter ducting and

changing the duct pipe to 4 inch diameter can greatly increase airflow.

Q: Why is there water dripping from my FAN?

A: Dripping water is typically condensation from a cold vent pipe. Insulating the

ductwork and FAN housing can help solve condensation problems. Running the

FAN longer will ensure moisture is completely removed from the duct. Another

possibility is rain entering the vent pipe through the roof vent opening.

Q: I have installed my FAN and it is not working, what do I do?

A: Make sure the black and white plug-in connector on the FAN is clicked into

place. Check all electrical connections like wire nuts and quick connects. Make

sure the circuit breaker is turned ON after completing all the electrical work. If you

have any concerns consult a licensed electrician.

Q: I still have additional questions.

A: Contact us at [email protected] or call our service department at

(877) 543-8698. We are happy to assist you with any additional questions.

La page est en cours de chargement...

ReVent RVS130 Guide d'installation

Ce manuel convient également à

ReVent RVS130 Guide d'installation

dans d''autres langues