Epson BrightLink 450Wi Guide d'installation

Catégorie
Projecteurs de données
Taper
Guide d'installation
Installation Guide
Guide d’installation
2
Safety Instructions
For your safety, read all the instructions in this guide before using the setting plate. Incorrect handling that
ignores instructions in this guide could damage the setting plate or could result in personal injury or property
damage. Keep this installation guide at hand for future reference.
Read the safety instructions in the User's Guide for your projector and follow the instructions in this
document.
Explanation of Symbols
The warning marks shown below are used throughout this installation guide to prevent personal injury or
property damage. Make sure you understand these warnings when reading this installation guide.
Safety Precautions for Installation
This symbol indicates information that, if ignored, could possibly result in personal injury or even death
due to incorrect handling.
This symbol indicates information that, if ignored, could possibly result in personal injury or physical
damage due to incorrect handling.
Symbol indicating an action that must not be done
Symbol indicating an action that should be done
The setting plate is designed specifically for mounting a projector to a wall. If anything other than a
projector is mounted, the weight may result in damage.
If the setting plate falls, it could cause personal injury or property damage.
The installation work (wall mounting) should be performed by specialists who have technical knowledge
and ability. Incomplete or incorrect installation could cause the setting plate to fall and cause personal
injury or property damage. Contact the customer support office listed in “Where to Get Help” in the User's
Guide for your projector when installing the setting plate.
Follow the instructions in this guide when installing the setting plate.
If the instructions are not followed, the setting plate may fall, resulting in personal injury or property damage.
Handle the power cable carefully.
Incorrect handling may cause fire or electric shock. Observe the following precautions when handling:
• Do not handle the power plug with wet hands.
• Do not use a power cable that is damaged or modified.
• Do not pull the power cable with too much force when routing the cable through the setting plate.
When you mount the projector on the wall with the setting plate, the wall requires enough strength to hold
the projector and the setting plate. Confirm the weight of the projector and the setting plate before
installation, and maintain the strength of the wall. If the wall is not strong enough, reinforce the wall
before installation.
Do not install the setting plate in a place where it might be subjected to vibration or shock.
Vibration or shock could cause damage to the projector or mounting surface. It could also cause the setting plate or
projector to fall and cause personal injury or property damage.
Install the setting plate so that it can sufficiently support the weight of the projector and setting plate, and
resist any horizontal vibration. Use M8 nuts and bolts.
Nuts and bolts smaller than M8 could cause the setting plate to fall. Epson takes no responsibility for any damage or
injury caused by incorrect installation.
Warning
Caution
Warning
3
English
Location
Before installing the projector, verify the power supply wiring for the installation location.
Install the projector away from other electric devices such as fluorescent lights or air conditioners. Some
kinds of fluorescent lights could interfere with the remote control of the projector.
It is recommended to keep connection cable length less than 65 ft (20 meters) to reduce external noise.
Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical
components from becoming dirty.
About This Installation Guide
This guide describes how to mount the BrightLink™ 450 Wi, PowerLite® 460, and PowerLite 450W projectors to
a wall using the exclusive setting plate.
The installation work should be performed by at least two qualified service personnel. If you need to
loosen any screws during installation, be careful not to drop the setting plate.
If the setting plate or projector falls, it could cause personal injury or property damage.
Inspect the setting plate on a regular basis to ensure there are no broken parts or loose screws.
If there are any broken parts, stop using the setting plate immediately. If the setting plate or projector falls, it could cause
personal injury or property damage.
Never modify the setting plate.
Do not hang on the setting plate or hang a heavy object on the setting plate.
If the projector or setting plate falls, it could cause personal injury or property damage.
If you use adhesives to prevent the screws from loosening or things such as lubricants or oils on the slide
plate fixing part of the projector, the case may crack and cause the projector to fall, resulting in personal
injury or property damage. Do not use adhesives, lubricants, or oils to install or adjust the setting plate.
Tighten all screws firmly after adjustment.
If the screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property
damage.
Never loosen the bolts and nuts after installation.
Confirm that the screws have not become loose on a regular basis. If you find any loose screws, tighten them firmly. If the
screws are not tightened firmly, the projector or setting plate may fall and cause personal injury or property damage.
Do not install the setting plate in a location where the operating temperature for your projector model
may be exceeded.
Such an environment may damage the projector.
Install the setting plate in a place free from excessive dust and humidity to prevent the lens or optical
components from becoming dirty.
Do not use excessive force when adjusting the setting plate.
The setting plate may break, resulting in personal injury.
Warning
Caution
4
1Package Contents sPage 5
2Specifications sPage 7
3Connecting Devices sPage 8
4Positioning the Projector sPage 9
(1) Installation worksheet for projecting on a pre-installed wall-
mounted board
(2) Installation worksheet for projecting on a plain wall
(3) Installation measurements in inches
(4) Installation measurements in millimeters
5Installing the Projector sPage 18
(1) Install the wall plate on the wall
(2) Determine the projection distance and pull out the slider
(3) Attach the setting plate to the wall plate
(4) Secure the projector to the setting plate
(5) Connect the power cable and other cables to the projector
6Adjusting the Image sPage 22
(1) Turn on the projector
(2) Display the test pattern
(3) Change the aspect ratio if necessary
(4) Adjust the focus
(5) Use the top adjustment dial to adjust the vertical tilt
(6) Use the right adjustment dial to adjust the horizontal rotation
(7) Use the left adjustment dial to adjust the horizontal roll
(8) Adjust the vertical position
(9) Adjust the forward/backward slide
(10) Turn off the display of the test pattern or computer image
7Attaching the Covers sPage 27
(1) Attach the wall plate cover and end cap
(2) Attach the cable cover to the projector
5
English
1. Package Contents
Mounting hardware
Use the bolts supplied with the setting plate to install it, as directed in this guide. Do not substitute these
bolts with any other types.
Use commercially available M8 x 50 mm anchors (at least 3) or 8 x 80 mm lag bolts (at least 3) to attach the
wall plate to the wall.
Gather the tools and parts you need before you begin installation.
Shape Name Quantity Application
M8 x 15 mm hexagon socket head cap bolt with
washer
2 For installing setting plate
M5 x 12 mm hexagon socket head cap bolt with
washer
2 For securing projector
M4 x 12 mm hexagon socket head cap bolt without
washer
2 For installing wall plate cover
Hexagon wrenches (for M4, M5, and M8)
Wall plate cover
Setting plate (wall mount)
Template sheet
(for installing the wall plate)
End cap
Wall plate
6
Projector box
Interactive pens and
AAA batteries*
Power cord
Projector
Epson Projector
S
oftware for Easy
Interactive Function CD*
VGA computer cable
Remote control
and AA batteries
USB cable*
Epson Projector
Software for Meeting
and Monitoring CD
Security sticker
Projector CD
*Items included for the BrightLink 450Wi only. Extra pen and battery set are included in the U.S. and Canada only.
7
English
2. Specifications
Wall plate
Setting plate adjustment range
Item Specification Remark Reference Page
Setting plate weight Approx. 13.89 lb
(6.3 kg)
Wall plate 4.85 lb (2.2 kg)
Covers and cap 1.04 lb (0.47 kg)
Forward/backward slide
adjustment range
0 to 11.81 in.
(300 mm)
Refer to the figure
below
Vertical slide adjustment range ± 4 ° Minimum: 1.10 in. (28 mm)
Maximum: 1.67 in. (42.5 mm)
s25
Vertical tilt adjustment range ± 5 ° Fine adjustments possible with adjustment dial s24
Horizontal rotation adjustment
range
± 5 ° Fine adjustments possible with adjustment dial s24
Horizontal roll adjustment range ± 3 ° Fine adjustments possible with adjustment dial s25
Horizontal slide adjustment range ± 1.77 in.
(45 mm)
Refer to the figure
below
[Unit: in. (mm)]
9.76 (248)
17.99 (457)
9.05 (230)
8.74 (222)
6.3 (160)
9.72 (247)
0.59 (15)
4.4 (112)
8 (203.2)
3.0
(76)
1.8 (46)
4.75
(121)
1.81 (46)
Forward/backward slide adjustment range:
0 to 11.81 in. (300 mm)
Horizontal slide adjustment range:
± 1.77 in. (45 mm)
8
3. Connecting Devices
Make sure you have the power cable, computer cable, USB cable, and other parts at the location where the
setting plate is to be installed.
Make sure you have all necessary cables for any devices, such as a document camera or microphone, that you
will connect to the projector.
External speakers LAN device
Microphone
USB cable
(for Easy Interactive Function)
Document camera
Computer
Computer cable
(for computer video output)
Connection Example
Dedicated USB cable
(supplied with document camera)
Audio cable
(commercially available product)
LAN cable
Power cord
9
English
4. Positioning the Projector
The BrightLink 450Wi and PowerLite 450W can project up to 96 inches diagonally for a WXGA image or 85
inches diagonally for an XGA image. The PowerLite 460 can project up to 102 inches diagonally for an XGA
image. You can project onto a pre-installed whiteboard or directly onto a plain wall. The height of the included
wall mount determines the maximum image size and how high the image appears on the wall or whiteboard.
The distance of the projector from the wall (once it is mounted on the adjustable arm of the setting plate) also
affects image size and position.
Use the following worksheets to determine the proper location of the wall plate on the wall. If you are
projecting onto a pre-installed whiteboard, use the worksheet below. If you are projecting on a plain wall, use
the worksheet on page 10.
Installation worksheet for projecting on a pre-installed wall-mounted
board
(1) Measure the ceiling height (distance from the floor to the ceiling).
(2) Measure the height of the board’s image area (h).
(3) Measure the width of the board’s image area (w).
(4) Measure the distance from the floor to the bottom of the board’s
image area (f).
(5) Measure the distance from the ceiling to the top of the board’s image area (c).
(6) Measure the thickness of the board (x).
_____
_____ (h)
_____ (w)
_____ (f)
_____ (c)
_____ (x)
10 in. (254 mm)—height of
wall plate plus cover
Required distance from top
of image area to wall plate (b)
Diagonal size of
image area (S)
Height of
image area (h)
Distance from ceiling to
top of image area (c)
Width of image area (w)
Distance from floor to
bottom of image area (f)
10
(7) Determine the aspect ratio of the board or of the images that will be
projected. For new computers or laptops, this will most likely be WXGA
(16:10). For older equipment, this will most likely be XGA (4:3). You may need
to consult your IT director for this information.
4:3 XGA 16:10 WXGA 16:9 Widescreen
(8) Using the tables on pages 12 to 16 for your aspect ratio and desired image
height (h), find the required distance between the top of the image area and
the wall plate (b).
(9) Determine the position for your projector installation by adding the values for
(f), (h), and (b), plus an additional 10 inches for the height of the wall plate
plus the cover.
If the ceiling height of your room (as noted in step 1) does not meet the
minimum ceiling height required for your board, you may need to select a
smaller image size or move the board to a lower position on the wall.
(10)After confirming your image size, use tape or a pencil to mark the distance (b)
from the top of the image area on the board to the bottom of the wall plate.
(11)Align the line (horizontal) on the template sheet with the (b) mark, then
align the center line on the template sheet with the center of the image area.
Follow the instructions on page 18 to install the projector.
Installation worksheet for projecting on a plain wall
(1) Measure the ceiling height (distance from the floor to the ceiling).
(2) Determine the desired aspect ratio of the image. For new computers or
laptops, this will most likely be WXGA (16:10). For older equipment, this will
most likely be XGA (4:3). You may need to consult your IT director for this
information.
4:3 XGA 16:10 WXGA 16:9 Widescreen
(3) Using the tables on pages 12 to 16 for your aspect ratio, select the largest
image size available for your ceiling height.
Image height (h)
Image width (w)
(4) Determine the desired distance from the floor to the bottom of the image
area (f).
The recommended minimum distance is 30 inches. Images appearing less
than 28 inches from the floor may be obstructed for some viewers.
(5) Find the top of the projected image area by adding distances (f) and (h).
(6) Use the tables on pages 12 to 16 to determine the required distance from the
top of the image area to the bottom of the wall plate (b).
(7) Add:
Required distance from top of image area to wall plate (b)
Height of image area (h)
Distance from floor to bottom of image area (f)
Height of wall plate plus cover
If the total exceeds the ceiling height, you will need to reduce the image size
or reduce the distance from the floor to the bottom of the image area.
_____ (b)
_____ (f)
_____ (h)
_____ (b)
+10 inches
_____ total
_____
_____ (h)
_____ (w)
_____ (f)
_____
_____ (b)
_____ (b)
_____ (h)
_____ (f)
+10 inches
_____ total
11
English
(8) After confirming your image size, use tape or a pencil to mark the distance (b) from the top of
the image area on the board to the bottom of the wall plate.
(9) Align the line (horizontal) on the template sheet with the (b) mark, then align the center
line on the template sheet with the center of the image area. Follow the instructions on page
18 to install the projector.
The tables on the following pages provide installation information for all supported image sizes. The
minimum ceiling height is based on an image 30 inches from the floor; if the image is lower, the minimum
ceiling height is reduced by the corresponding measurement.
Use the worksheets, the illustration below, and the information in the tables on the following pages to
determine the projection distance and placement of the wall plate. The recommended range for projection
distance (a) is 2.76 to 14.57 inches (7 to 37 cm).
10 in. (254 mm) —height
of wall plate plus cover
Required distance from top
of image area to wall plate (b)
Diagonal image
size (S)
Ceiling
height
Distance from ceiling to
top of image area (c)
Width of image area (w)
Distance from floor to
bottom of image area (f)
Height of
image area (h)
Wall plate
Projection surface
Offset value for the position of
the center of the screen and the
center of the wall plate
Distance from wall of projection
surface or whiteboard
2.55 in. (65 mm)
10 in. (254 mm)
12
Installation measurements in inches
Diagonal
image
size
(S)
16:10 WXGA
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
4:3 XGA
for BrightLink 450Wi and
PowerLite 450W
16:9 Widescreen
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
Projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
55” 83.4 44.0 33.0 3.7 10.4
56” 84.2 44.8 33.6 4.1 10.6
57” 85.0 45.6 34.2 4.4 10.7
58” 85.7 46.4 34.8 4.8 10.9
59” 81.2 50.0 31.3 2.7 10.0 86.5 47.2 35.4 5.2 11.1
60” 81.9 50.9 31.8 3.0 10.1 87.3 48.0 36.0 5.5 11.3 81.4 52.3 29.4 3.5 12.0
61” 82.6 51.7 32.3 3.3 10.3 88.0 48.8 36.6 5.9 11.5 82.1 53.2 29.9 3.9 12.2
62” 83.3 52.6 32.9 3.6 10.4 88.8 49.6 37.2 6.2 11.6 82.7 54.0 30.4 4.2 12.4
63” 83.9 53.4 33.4 4.0 10.6 89.6 50.4 37.8 6.6 11.8 83.4 54.9 30.9 4.5 12.5
64” 84.6 54.3 33.9 4.4 10.7 90.4 51.2 38.4 7.0 12.0 84.1 55.8 31.4 4.8 12.7
65” 85.3 55.1 34.4 4.6 10.9 91.1 52.0 39.0 7.3 12.1 84.8 56.7 31.9 5.2 12.9
66” 86.0 56.0 35.0 4.9 11.0 91.9 52.8 39.6 7.7 12.3 85.4 57.5 32.4 5.5 13.1
67” 86.7 56.8 35.5 5.2 11.1 92.7 53.6 40.2 8.0 12.5 86.1 58.4 32.8 5.8 13.2
68” 87.3 57.7 36.0 5.5 11.3 93.4 54.4 40.8 8.4 12.6 86.8 59.3 33.3 6.2 13.4
69” 88.0 58.5 36.6 5.9 11.4 94.2 55.2 41.4 8.8 12.8 87.4 60.1 33.8 6.5 13.6
70” 88.7 59.4 37.1 6.2 11.6 95.0 56.0 42.0 9.1 13.0 88.1 61.0 34.3 6.8 13.8
71” 89.4 60.2 37.6 6.5 11.7 95.7 56.8 42.6 9.5 13.1 88.8 61.9 34.8 7.2 14.0
72” 90.0 61.1 38.2 6.8 11.9 96.5 57.6 43.2 9.8 13.3 89.4 62.8 35.3 7.5 14.1
73” 90.7 61.9 38.7 7.1 12.0 97.3 58.4 43.8 10.2 13.5 90.1 63.6 35.8 7.8 14.3
74” 91.4 62.8 39.2 7.5 12.2 98.0 59.2 44.4 10.6 13.6 90.8 64.5 36.3 8.1 14.5
75” 92.1 63.6 39.7 7.8 12.3 98.8 60.0 45.0 10.9 13.8 91.5 65.4 36.8 8.4 14.7
13
English
* Based on an image 30 inches from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
76” 92.8 64.4 40.3 8.1 12.5 99.6 60.8 45.6 11.3 14.0 92.1 66.2 37.3 8.8 14.9
77” 93.4 65.3 40.8 8.4 12.6 100.3 61.6 46.2 11.7 14.1 92.8 67.1 37.8 9.1 15.0
78” 94.1 66.1 41.3 8.7 12.8 101.1 62.4 46.8 12.0 14.3 93.5 68.0 38.2 9.4 15.2
79” 94.8 67.0 41.9 9.0 12.9 101.9 63.2 47.4 12.4 14.5 94.1 68.9 38.7 9.7 15.4
80” 95.5 67.8 42.4 9.4 13.1 102.6 64.0 48.0 12.7 14.6 94.8 69.7 39.2 10.1 15.6
81” 96.2 68.7 42.9 9.7 13.2 103.4 64.8 48.6 13.1 14.8 95.5 70.6 39.7 10.4 15.8
82” 96.8 69.5 43.5 10.0 13.4 104.2 65.6 49.2 13.5 15.0 96.1 71.5 40.2 10.7 15.9
83” 97.5 70.4 44.0 10.3 13.5 104.9 66.4 49.8 13.8 15.2 96.8 72.3 40.7 11.1 16.1
84” 98.2 71.2 44.5 10.6 13.7 105.7 67.2 50.4 14.2 15.3 97.5 73.2 41.2 11.4 16.3
85” 98.9 72.1 45.0 11.0 13.8 106.5 68.0 51.0 14.5 15.5 98.2 74.1 41.7 11.7 16.5
86” 99.5 72.9 45.6 11.3 14.0 98.8 75.0 42.2 12.0 16.7
87” 100.2 73.8 46.1 11.6 14.1 99.5 75.8 42.7 12.4 16.8
88” 100.9 74.6 46.6 11.9 14.3 100.2 76.7 43.1 12.7 17.0
89” 101.6 75.5 47.2 12.2 14.4 100.8 77.6 43.6 13.0 17.2
90” 102.3 76.3 47.7 12.6 14.6 101.5 78.4 44.1 13.3 17.4
91” 102.9 77.2 48.2 12.9 14.7 102.2 79.3 44.6 13.7 17.6
92” 103.6 78.0 48.8 13.2 14.8 102.8 80.2 45.1 14.0 17.7
93” 104.3 78.9 49.3 13.5 15.0 103.5 81.1 45.6 14.3 17.9
94” 105.0 79.7 49.8 13.8 15.2
95” 105.6 80.6 50.3 14.2 15.3
96” 106.3 81.4 50.9 14.5 15.5
Diagonal
image
size
(S)
16:10 WXGA
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
4:3 XGA
for BrightLink 450Wi and
PowerLite 450W
16:9 Widescreen
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
Projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
14
Installation measurements in millimeters
Diagonal
image
size
(S)
16:10 WXGA
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
4:3 XGA
for BrightLink 450Wi and
PowerLite 450W
16:9 Widescreen
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
Projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
55” 2119 1118 838 94 265
56” 2139 1138 853 104 269
57” 2158 1158 869 113 274
58” 2178 1179 884 122 278
59” 2063 1271 794 68 253 2197 1199 899 131 282
60” 2080 1292 808 76 257 2217 1219 914 140 287 2068 1328 747 90 304
61” 2098 1314 821 84 260 2236 1240 930 149 291 2085 1350 760 98 309
62” 2115 1335 835 92 264 2256 1260 945 158 295 2102 1373 772 106 314
63” 2132 1357 848 100 268 2275 1280 960 168 299 2119 1395 785 114 318
64” 2149 1379 862 108 272 2295 1300 975 177 304 2136 1417 797 123 323
65” 2167 1400 875 117 276 2314 1321 991 186 308 2153 1439 809 131 327
66” 2184 1422 888 125 279 2334 1341 1006 195 312 2170 1461 822 139 332
67” 2201 1443 902 133 283 2353 1361 1021 204 316 2187 1483 834 148 336
68” 2218 1465 915 141 287 2373 1382 1036 213 321 2204 1505 847 156 341
69” 2235 1486 929 149 291 2393 1402 1052 223 325 2221 1528 859 164 346
70” 2253 1508 942 157 294 2412 1422 1067 232 329 2238 1550 872 173 350
71” 2270 1529 956 165 298 2432 1443 1082 241 333 2255 1572 884 181 355
72” 2287 1551 969 173 302 2451 1463 1097 250 338 2272 1594 897 189 359
73” 2304 1572 983 181 306 2471 1483 1113 259 342 2289 1616 909 198 364
74” 2322 1594 996 189 309 2490 1504 1128 268 346 2306 1638 921 206 368
75” 2339 1615 1010 197 313 2510 1524 1143 277 351 2323 1660 934 214 373
15
English
* Based on an image 762 mm from the floor; if the image is lower, the minimum ceiling height is reduced by the corresponding measurement.
76” 2356 1637 1023 205 317 2529 1544 1158 287 355 2340 1682 946 223 378
77” 2373 1659 1037 214 321 2549 1565 1173 296 359 2357 1705 959 231 382
78” 2391 1680 1050 222 325 2568 1585 1189 305 363 2374 1727 971 239 387
79” 2408 1702 1063 230 328 2588 1605 1204 314 368 2391 1749 984 247 391
80” 2425 1723 1077 238 332 2607 1626 1219 323 372 2408 1771 996 256 396
81” 2442 1745 1090 246 336 2627 1646 1234 332 376 2425 1793 1009 264 400
82” 2459 1766 1104 254 340 2646 1666 1250 342 380 2442 1815 1021 272 405
83” 2477 1788 1117 262 343 2666 1687 1265 351 385 2459 1837 1034 281 409
84” 2494 1809 1131 270 347 2685 1707 1280 360 389 2476 1860 1046 289 414
85” 2511 1831 1144 278 351 2705 1727 1295 369 393 2493 1882 1058 297 419
86” 2528 1852 1158 286 355 2510 1904 1071 306 423
87” 2546 1874 1171 294 358 2527 1926 1083 314 428
88” 2563 1895 1185 303 362 2544 1948 1096 322 432
89” 2580 1917 1198 311 366 2561 1970 1108 331 437
90” 2597 1939 1212 319 370 2578 1992 1121 339 441
91” 2615 1960 1225 327 374 2595 2015 1133 347 446
92” 2632 1982 1239 335 377 2612 2037 1146 356 451
93” 2649 2003 1252 343 381 2629 2059 1158 364 455
94” 2666 2025 1265 351 385
95” 2683 2046 1279 359 389
96” 2701 2068 1292 367 392
Diagonal
image
size
(S)
16:10 WXGA
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
4:3 XGA
for BrightLink 450Wi and
PowerLite 450W
16:9 Widescreen
for BrightLink 450Wi,
PowerLite 450W, and PowerLite 460
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
Min.
ceiling
height*
Image
width
(w)
Image
height
(h)
Min.
Projection
distance
(a)
Distance
from top
of image
to wall
plate (b)
16
*Based on an image 30 inches (762 mm) from the floor; if the image is lower, the minimum ceiling height is
reduced by the corresponding measurement.
4:3 XGA for PowerLite 460 in inches (and millimeters)
S w h a b
Diagonal
image size
Minimum
Ceiling Height*
Image width Image height Minimum Projection
Distance (Wide)
Distance from top of
image to wall plate
63" 84.7 (2121) 50.4 (1280) 37.8 (960) 2.8 (71) 6.9 (175)
64" 85.4 (2139) 51.2 (1300) 38.4 (975) 3.1 (79) 7.0 (177)
65" 86.1 (2156) 52.0 (1321) 39.0 (991) 3.4 (87) 7.1 (179)
66" 86.7 (2174) 52.8 (1341) 39.6 (1006) 3.7 (94) 7.1 (181)
67" 87.4 (2191) 53.6 (1361) 40.2 (1021) 4.0 (102) 7.2 (184)
68" 88.1 (2209) 54.4 (1382) 40.8 (1036) 4.3 (110) 7.3 (186)
69" 88.8 (2226) 55.2 (1402) 41.4 (1052) 4.6 (117) 7.4 (188)
70" 89.5 (2273) 56.0 (1422) 42.0 (1067) 4.9 (125) 7.5 (191)
71" 90.2 (2291) 56.8 (1443) 42.6 (1082) 5.2 (133) 7.6 (193)
72" 90.9 (2308) 57.6 (1463) 43.2 (1097) 5.5 (140) 7.7 (195)
73" 91.6 (2326) 58.4 (1483) 43.8 (1113) 5.8 (148) 7.8 (197)
74" 92.3 (2343) 59.2 (1504) 44.4 (1128) 6.1 (155) 7.9 (200)
75" 93.0 (2361) 60.0 (1524) 45.0 (1143) 6.4 (163) 8.0 (202)
76" 93.6 (2378) 60.8 (1544) 45.6 (1158) 6.7 (171) 8.0 (204)
77" 94.3 (2396) 61.6 (1565) 46.2 (1173) 7.0 (178) 8.1 (207)
78" 95.0 (2414) 62.4 (1585) 46.8 (1189) 7.3 (186) 8.2 (209)
79" 95.7 (2431) 63.2 (1605) 47.4 (1204) 7.6 (194) 8.3 (211)
80" 96.4 (2449) 64.0 (1626) 48.0 (1219) 7.9 (201) 8.4 (213)
81" 97.1 (2466) 64.8 (1646) 48.6 (1234) 8.2 (209) 8.5 (216)
82" 97.8 (2484) 65.6 (1666) 49.2 (1250) 8.5 (216) 8.6 (218)
83" 98.5 (2501) 66.4 (1687) 49.8 (1265) 8.8 (224) 8.7 (220)
84" 99.2 (2519) 67.2 (1707) 50.4 (1280) 9.1 (232) 8.8 (223)
85" 99.9 (2536) 68.0 (1727) 51.0 (1295) 9.4 (239) 8.9 (225)
86" 100.5 (2554) 68.8 (1748) 51.6 (1311) 9.7 (247) 8.9 (227)
87" 101.2 (2571) 69.6 (1768) 52.2 (1326) 10.0 (255) 9.0 (229)
88" 101.9 (2589) 70.4 (1788) 52.8 (1341) 10.3 (262) 9.1 (232)
89" 102.6 (2606) 71.2 (1808) 53.4 (1356) 10.6 (270) 9.2 (234)
90" 103.3 (2624) 72.0 (1829) 54.0 (1372) 10.9 (277) 9.3 (236)
91" 104.0 (2641) 72.8 (1849) 54.6 (1387) 11.2 (285) 9.4 (239)
92" 104.7 (2659) 73.6 (1869) 55.2 (1402) 11.5 (293) 9.5 (241)
93" 105.4 (2676) 74.4 (1890) 55.8 (1417) 11.8 (300) 9.6 (243)
94" 106.1 (2694) 75.2 (1910) 56.4 (1433) 12.1 (308) 9.7 (245)
95" 106.8 (2711) 76.0 (1930) 57.0 (1448) 12.4 (316) 9.8 (248)
96" 107.4 (2729) 76.8 (1951) 57.6 (1463) 12.7 (323) 9.8 (250)
97" 108.1 (2747) 77.6 (1971) 58.2 (1478) 13.0 (331) 9.9 (252)
98" 108.8 (2764) 78.4 (1991) 58.8 (1494) 13.3 (339) 10.0 (255)
99" 109.5 (2782) 79.2 (2012) 59.4 (1509) 13.6 (346) 10.1 (257)
100" 110.2 (2799) 80.0 (2032) 60.0 (1524) 13.9 (354) 10.2 (259)
101" 110.9 (2817) 80.8 (2052) 60.6 (1539) 14.2 (361) 10.3 (261)
102" 111.6 (2834) 81.6 (2073) 61.2 (1554) 14.5 (369) 10.4 (264)
17
English
If you have a pre-existing whiteboard, refer to the table below to identify common models and sizes. If your
board is listed here, use the dimensions to reference the installation requirements found on pages 12 to 16.
Interactive whiteboard sizes
Diagonal size 16:10 WXGA 4:3 XGA 16:9 Widescreen
60 inches RM ClassBoard2 60
63 inches Hitachi® StarBoard FX-63
64 inches SMART Board 660
Promethean ActivBoard 164
71 inches INTERWRITE BOARD 1071
77 inches Hitachi Cambridge Board 77
Hitachi StarBoard FX-77
SMART Board 680
77.5 inches RM ClassBoard2 77.5
INTERWRITE® BOARD 1077
78 inches PolyVision® TS 600/ TS610 /
TSL610/ENO 2610
PolyVision TS610
Promethean ActivBoard 178 / 378
82 inches Hitachi StarBoard FX-82W
85 inches INTERWRITE BOARD 1085
87 inches SMART Board 685
Promethean ActivBoard 387
——
93 inches PolyVision ENO 2810
94 inches SMART Board 690
96 inches Epson BrightLink 450Wi
18
5. Installing the Projector
Make sure to follow the steps below to install the setting plate. If you ignore these steps, the setting plate
could fall and cause personal injury or property damage.
AInstall the wall plate on the wall
(1) Determine the template sheet position.
From the tables on pages 12 to 16, confirm the screen size (S) and the distance between the
projection surface and wall plate (b).
Align the CTR line (vertical) of the template sheet with the center line (vertical) of the projection
surface.
Confirm where the beams or studs are within the wall, and shift the position left or right as necessary.
The position can be shifted horizontally left or right from the center line of the projection surface by
up to 1.77 in. (45 mm).
Align the line (horizontal) of the template with the height of (b).
(2) Attach the template sheet to the wall.
If you need to install a junction box, you can use the cutout areas in the wall plate for the box.
The junction box needs to be recessed into the wall if you want to use the wall plate cover.
The maximum combined weight of the setting plate and the projector is approximately 33.5 lb
(15.2 kg). When you install the setting plate, calculate the permissible weight, carefully check
the construction, material, and strength of the wall, and perform the installation properly using
the most appropriate method.
Center line of projection surface
CTR line of template sheet
line of template sheet
65 mm (2.55 in.)
19
English
(3) Make mounting holes in the wall in the required locations.
The wall plate needs to be secured by commercially available anchors or lag bolts in the
following places. It is recommended that the wall plate be secured in at least three places.
If securing the wall plate in four places, make the holes indicated by A or B in the figure.
If securing the wall plate in three places, make the holes indicated by C in the figure.
(4) Remove the template sheet.
(5) Mount the wall plate on the wall.
BDetermine the projection distance and pull out the slider
(1) Using the tables on pages 12 to 16, calculate the distance (a) from the projection surface to
the front of the projector.
(2) Loosen the four screws and pull out the slider on the setting plate.
Align the slider with the mark on the slider measure that is a distance (a+x) equivalent to the
distance (a) plus the thickness of the board (x). See the tables on pages 12 to 16. The
recommended range for projection distance (a) is 2.76 to 14.57 in. (7 to 37 cm).
Four mounting holes Three mounting holes
When you mount the projector on the wall with the setting plate, the wall needs to be
strong enough to hold the projector and the setting plate. Confirm the weight of the
projector and the setting plate before installation, and maintain the strength of the wall. If
the wall is not strong enough, reinforce the wall before installation.
Install the setting plate so that it can sufficiently support the weight of the projector and
setting plate, and resist any horizontal vibration. Use M8 nuts and bolts. Nuts and bolts
smaller than M8 could cause the setting plate to fall.
Epson takes no responsibility for any damage or injury caused by incorrect installation.
Warning
Screws (4 )
Slider measure
20
CAttach the setting plate to the wall plate
(1) Hang the setting plate hook onto the wall plate bar (A).
(2) Lift up the setting plate and pass the cables through it (B).
(3) Tighten the two M8 x 15 mm hexagon socket head cap bolts and two M8 x 35 mm hexagon
socket head cap bolts supplied with the setting plate so that the setting plate becomes
vertical against the wall (C).
Use the two M8 x 35 mm hexagon socket head cap bolts to adjust the vertical position.
s25
DSecure the projector to the setting plate
(1) Loosen the two screws and remove the cable cover from the projector.
Take care not to trap the cables between the setting plate and wall plate.
Caution
Setting plate
Cables
Wall plate
M8 x 15 mm hexagon socket
head cap bolts (one on left
and one on right)
Wall plate bar
M8 x 35 mm hexagon
socket head cap bolts (2)
Setting plate hook
Cable cover
Screws (2)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Epson BrightLink 450Wi Guide d'installation

Catégorie
Projecteurs de données
Taper
Guide d'installation

dans d''autres langues