Fisher & Paykel HC36DTXB2 Guide d'installation

INSTALLATION GUIDE/USER GUIDE

GUIDE D’INSTALLATION/GUIDE D’UTILISATION

US CA

CHIMNEY BOX

VENTILATION HOOD

HC24DTXB2, HC30DTXB2 & HC36DTXB2 models

HOTTE DE VENTILATION

MURALE DÉCORATIVE

Modèles HC24DTXB2, HC30DTXB2 & HC36DTXB2

English Page 1 – 22

Français

Page 25 – 46

1

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this user guide

may not be available in all markets

and are subject to change at any time.

For current details about model and

specification availability in your country,

go to our website fisherpaykel.com or

contact your local Fisher & Paykel dealer.

Registration

Register your product with us so we can

provide you with the best service possible.

To register your product visit our website:

fisherpaykel.com

EN

Introduction 3

Safety and warnings 4

Installation instructions 6

Operating instructions 18

Cleaning and maintenance 19

Parts and accessories 21

Service and Warranty 22

CONTENTS

3

INTRODUCTION

Thank you for purchasing a Fisher & Paykel product.

Thousands of hours go into the design, engineering, testing and perfecting of each

Fisher & Paykel appliance. The care and attention given to creating these beautiful

products doesn’t stop once it has found its home with you.

This use and care manual will answer most of your questions about the set-up, use

and on-going maintenance of your Fisher & Paykel product; however if you require

further information about your product and its use please consult our website for

solutions and further contact information to discuss with a service representative.

To ensure you receive all relevant product updates and the best service possible,

registeryour Fisher & Paykel products through our website.

EN

5

SAFETY AND WARNINGS

– When cutting or drilling into wall or ceiling, do not damage electrical wiring

andother hidden utilities.

– Ducted fans must always be vented to the outdoors.

– This unit must be grounded.

●CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct air

outside—Do not vent exhaust air into spaces within walls or ceilings or into attics,

crawl spaces, or garages.

●WARNING: To reduce the risk of fire, use only metal ductwork.

●WARNING: To reduce the risk of fire or electric shock, do not use this fan with

any solid-state speed control device.

●WARNING: To reduce the risk of a range top grease fire:

– Never leave surface units unattended at high settings. Boilovers cause

smoking and greasy spillovers that may ignite. Heat oils slowly on low or

medium settings.

– Always turn hood ON when cooking at high heat or when flambéing food

(ieCrepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé)

– Clean ventilating fans frequently. Grease should not be allowed to

accumulate on fan or filter.

– Use proper pan size. Always use cookware appropriate for the size of

the surface element.

●WARNING: To reduce the risk of injury to persons in the event of a range top

grease fire, observe the following*:

– SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then

turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not

go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

– NEVER PICK UP A FLAMING PAN—You may be burned.

– DO NOT USE WATER, including wet dishcloths or towels—a violent steam

explosion will result.

– Use an extinguisher ONLY if:

– You know you have a Class ABC extinguisher, and you already know

how to operate it.

– The fire is small and contained in the area where it started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

●WARNING: Unplug or disconnect the appliance from the power supply before

servicing or cleaning.

●CAUTION: To reduce the risk of fire and electric shock when product is used in

recirculation mode, use only conversion kit model 792580 Recirculation Diverter

and791772Recirculation Carbon Filter x2.

READ AND SAVE THESE INSTRUCTIONS

* Based on “Kitchen Firesafety Tips” published by NFPA.

EN

6

INSTALLATION INSTRUCTIONS

Contents of packaging

Upper chimney bracket

(1)

Installation instructions

User guide manual

(1)

Chimney

(1)

6” (152mm) diameter

Ducting adapter with

back draft damper

(1)

1⁄” (30mm)

Expansion plug

(10)

Upper chimney

(1)

Ventilation hood

(1)

Power connection box

(1)

Chimney bracket

(1)

US CA

CH MNEY BOX

VENTILAT ON HOOD

HOTTE DE VENTILATION

MURALE DÉCORAT VE

7

INSTALLATION INSTRUCTIONS

1⁄” (30mm)

Self tapping screw

(10)

⅜” (10mm)

Self tapping screw

(4)

1¾” (44mm)

Drywall expansion plug

(8)

⅜” (10mm)

Screw

(2)

EN

8

INSTALLATION INSTRUCTIONS

Please read the entire instructions before installing the ventilation hood.

Product dimensions

h

i

C

j

g f

A

B

D

E

Ø

l

k

UL power

connection box

min

max

9

INSTALLATION INSTRUCTIONS

HC24DTXB2 HC30DTXB2 HC36DTXB2

PRODUCT DIMENSIONS inches (mm) inches (mm) inches (mm)

AMin overall height of product 23¾” (603) 23¾” (603) 23¾” (603)

AMax overall height of product 41⁄” (1043) 41⁄” (1043) 41⁄” (1043)

BOverall width of product 23⁄” (598) 29¾” (755) 35⅜” (898)

COverall depth of product 19⁄” (500) 19⁄” (500) 19⁄” (500)

DHeight of product 2⁄” (65) 2⁄” (65) 2⁄” (65)

EHeight of stainless steel face panel 1⁄” (36) 1⁄” (36) 1⁄” (36)

FWidth of chimney 12⅝” (320) 12⅝” (320) 12⅝” (320)

GDepth of chimney 11⁄” (290) 11⁄” (290) 11⁄” (290)

HDistance from center of ducting

outlet to back of product 3⅜” (85) 3⅜” (85) 3⅜” (85)

IDistance from center of ducting

outlet to side of chimney 6⁄” (160) 6⁄” (160) 6⁄” (160)

JDiameter of ducting outlet 6” (152) 6” (152) 6” (152)

KDistance between center of lights 9⅝” (244) 9⅝” (244) 9⅝” (244)

LDistance between center of lights

and back of product 1⅜” (35) 1⅜” (35) 1⅜” (35)

IMPORTANT!

Actual product dimensions may vary by ± ⁄”(2 mm).

EN

10

INSTALLATION INSTRUCTIONS

Height of ventilation hood

INSTALLATION DIMENSIONS inches (mm)

MInstallation height

Ducted

Recirculation

min. 24⁄” (627)–max. 43⁄” (1034)

min. 26⅞” (682)–max. 43⁄” (1034)

NHeight top of cooking surface

to base of product

min. 26” (660)–max. recommended 36” (915)

This ventilation hood must be installed no lower than the minimum height

indicated in the table above. Minimum installation height may be greater if required

by the cooktop manufacturer or safety and warning section of this user guide.

Installation at the minimum height will improve the efficiency of capturing

cooking odors, grease and smoke. Installation at the maximum height improves

user ergonomics by offering increased head room.

M

N

11

INSTALLATION INSTRUCTIONS

WARNING!

To reduce the risk of fire, use only metal ductwork. Do not use flexible plastic ducting

CAUTION!

To reduce risk of fire and to properly exhaust air, be sure to duct air outside—

do not vent exhaust air into spaces within walls or ceilings or into attics,

crawl spaces, or garages.

Venting options

Attention should be given to ensure that any applicable regulations concerning the

discharge of exhaust air are fulfilled.

The ventilation hood can be installed to operate with the exhaust air ducted

externally from the kitchen, or installed to operate with the exhaust air recirculating

within the kitchen.

Ducted

For ducted installation it is recommended that 6” (152 mm) diameter, rigid or semi-rigid

ducting is used. This will require a 6⁄” (160 mm) (min) round hole in the ceiling or wall.

Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use

rigid or semi-rigid ducting for reduced noise and increased airflow. Flexible metal

ducting should only be used as a last resort (ie in difficult installations) and if used

ensure that it is straight and smooth and extended as much as possible.

Recirculating

To enable the product to operate with the air recirculating, purchase a recirculation

diverter and carbon filters or recirculation kit (refer to the ‘Parts and accessories’

section). This recirculation diverter is required to channel the air out the side vents

at the top of the chimney and the carbon filters are required to remove odors.

Note: a ducting hole is not required in the wall or ceiling if the ventilation hood is

installed to operate with exhaust air recirculating.

EN

13

INSTALLATION INSTRUCTIONS

PRODUCT DIMENSIONS inches (mm)

oLower ventilation hood attachment point width 20” (508)

PLower ventilation hood attachment point height 1⁄” (43)

qUpper ventilation hood attachment point width 9⅞” (250)

rUpper ventilation hood attachment point height 11⁄” (288)

sChimney bracket attachment point width 9¼” (235)

tChimney bracket attachment point height 22¼” (566)

uUpper chimney bracket attachment point width 9⅞” (250)

vUpper chimney bracket attachment point height 1” (25)

Fig.2

Upper chimney bracket

attachment points

Chimney bracket

attachment points

Upper ventilation

hood attachment point

Lower ventilation

hood attachment point

u

o

v

t

r

p

q

s

EN

15

INSTALLATION INSTRUCTIONS

4 Wall mounting

●Remove the filters—pull the relative catch and tilt the

filter downwards until it disengages from the supports.

●Hang the ventilation hood off the upper ventilation

hood mounting screws with ⁄” (2 mm) gap.

Hang off the keyhole attachment points on the back

of the ventilation hood then tighten the screws.

●Attach the lower ventilation hood mounting screws

to fix the ventilation hood to the wall.

●Refit the filters.

EN

16

INSTALLATION INSTRUCTIONS

WARNING!

Electrical wiring must be done by qualified person(s) in accordance with

all applicable codes and standards and the unit must be grounded.

5 Electrical connection

●Run three wires, two for the power supply and one for the ground wire, from the

power connection box on the ventilation hood to a power connection point near

the installation.

●Open the power connection box on the ventilation hood and secure the power

conductor with a cULus listed strain relief (not included).

●Connect the power conductors to the conductors for the ventilation hood,

black to black and white to white.

●Connect the grounding wire (green or bare) to the ground conductor (green)

of the ventilation hood power connection box.

●Secure all the connections with cULus listed wire nuts.

●Replace the power connection box cover.

M

Switch

Interrupteur

Brown/Marron

Gray/Gris

Black/Noir

Red/Rouge

Blue/Bleu

Purple/Violet

White/Blanc

Yellow/Green

Jaune/Vert

White/Blanc

Yellow/Green Jaune/VertGround

Brown/Marron Motor

Gray/Gris

Black/Noir

Red/Rouge

Blue/Bleu

Black/Noir

White/Blanc

Black/Noir (L)

White/Blanc (N)

Green/Vert (E)

Black/Noir

White/Blanc Motor

Orange/Orange Motor

Capacitor

Bornier

Junction

Box

Green/Vert

120V~60Hz

Gray 4 speed

Black 3 speed

Red 2 speed

Blue 1 speed

Brown (neutral)

Lamp/Lampes

La page charge ...

Fisher & Paykel HC36DTXB2 Guide d'installation

Ce manuel convient également à

Fisher & Paykel HC36DTXB2 Guide d'installation

dans d''autres langues

Documents connexes