Modern Forms FH-W1811 Aviator Flush Mode d'emploi

Aviator Flush

Installation Instructions

works with the

Google Assistant

FH-W1811

Aviator Flush Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FH-W1811Aviator Flush Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FH-W1811

Aviator Flush Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FH-W1811 Aviator Flush Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FH-W1811

Aviator Flush Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

PRUHHɝFLHQWWKDQ$&IDQV

:L)LDQG%OXHWRRWKHQDEOHG

IRUȵH[LEOHFRQWURO

%OXHWRRWK:DOO&RQWURO

'LPVOLJKWWR_212))

IDQVSHHGV_6ROGVHSDUDWHO\

F-WCBT-WT :KLWH

%OXHWRRWK5HPRWH&RQWURO

'LPVOLJKWWR_212))

IDQVSHHGV

F-RCBT-WT :KLWH

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FH-W1811 Aviator Flush Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Installing the Mounting Bracket 10

3. Attaching the Fan Blades 12

4. Attaching Decorative Lower Cap 12

5. Hanging the Fan 12

6. Making the Electrical Connections 14

7. Finishing the Installation 16

8. Installing the Wall Control 18

9. Installing the LED Luminaire Module (Optional) 20

10. Controlling the Fan 22

11. Reset 24

12. Breeze Mode 24

13. Application 24

14. Accessories 26

15. Troubleshooting 27-30

FH-W1811

Aviator Flush Instructions8

Package Contents

7. Control Receiver

w/Hardware

F-R3-1811-054

8. Remote Control w/Wire Nuts

F-RCBT-WT

Hardware Bag

RPL-AVIATORFH-PARTS

1. Blade Set of 3

RPL-F1811-54-BD-**

2. Blade Collector Ring

3. Mounting Bracket

RPL-F1811-HANGER-**

4. Hanger Gasket

5. Motor Assembly

6. Bottom Cap

RPL-F1811-54-CA-**

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

** denotes ﬁnish code of fan *** denotes blade sweep of fan

• Part A

• Part B

• Part C

• Part D

• Part E

• Part F

Hardware Bag

RPL-AVIATORFH-PARTS

#10 x 38mm Pan Head Phillip Screws (2)

#10x76mm Pan Head Phillip Wood Screws (1)

3/16 * 3/8 Flat Head Phillips Screw (5)

3/16”( 5.2x8.4x1.0mm) Spring Washer (1)

6.5x19x2mm Flat Washer (1)

3/16” Star Washer (2)

4*9 Flat Head Customed Philips Screw (10)

1/4”x16mm Phil/Slotted Pan Head Screw (7)

5 x 14 x 1mm Flat Washer (2)

B: Blade

C: Attach The Blade Collector Ring

To Blade

E: Wire Nuts

D: Safety Cable

F: Attach Housing to Mounting Bracket

(Found with the receiver)

Note: Some bags may contain extra parts for your convenience.

FH-W1811 Aviator Flush Instructions 9

1

8

4

5

2

6

7

3

IMPORTANT: Please make note

of the MAC ID on the

receiver and keep it in a

safe place.

MAC ID

Hanging Weight: OEV

F: Attach Housing to Mounting Bracket

FH-W1811

Aviator Flush Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure. Use Part A if

needed.

Figures 1-1B are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

1. Disconnect power to the fan location at the breaker. A licensed

electrician must install the fan.

2. Pass the 120-volt supply wires through the center hole in the

ceiling mounting bracket as shown (Fig. 2). Secure the hanger

plate and hanger gasket to the ceiling outlet box with the screws

and washers that come included with your outlet box. (Fig. 2).

REMEMBER to turn oﬀ power at the breaker.

Follow the steps below to hang your fan properly:

2. Installing the Mounting Bracket

FH-W1811 Aviator Flush Instructions 11

1

1A

1B

2

1

2

3

1. Support Brace

2. Outlet Box

3. Joist

FH-W1811

Aviator Flush Instructions12

1. Pass supply wires through mounting plate.

2. Lift motor assemby and hang it on the hook on the

mounting plate using one of the screw holes (Fig.5).

3. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided (Fig. 5).

NOTE: A Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over

35 lbs. in both flush and downrod models in the United States.

5. Hanging the Fan

3. Attaching the Fan Blades

4. Attaching Decorative Lower Cap

1. Place blade on motor as shown (Fig. 3) and secure with the

blade attachment screws. Use Part B.

2. Repeat this procedure with the remaining blades (Fig. 3).

3. Secure the bottom of the blades together using the provided

blade collector ring and hardware (Fig. 3A). Use Part C.

1. Tightly twist the decorative lower cap onto the

motor assembly (Fig. 4).

(Skip this step if you purchased the optional luminaire)

FH-W1811 Aviator Flush Instructions 13

3

4

3A

5

FH-W1811

Aviator Flush Instructions14

6. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the motor assembly with the flat side of the

receiver facing the ceiling (Fig. 6).

Motor to Receiver & Receiver to house supply wires (Fig. 6A).

1. Connect the motor assembly ground wire, mounting bracket

ground wire and receiver ground wire to the ground wire in

outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

Failure to make proper color-coded connections may reslult in

damage to your receiver.Connect the red wire from the fan to the red

wire marked

“TO MOTOR” from the receiver.

2. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

3. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

4. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

5. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

6. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

7. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

NOTE: If you are not installing the optional luminaire module - cap oﬀ

white wires marked “FOR LIGHT” and blue wires marked “FOR LIGHT”

from receiver and corresponding wires from fan with wire nuts and

electrical tape.

FH-W1811 Aviator Flush Instructions 15

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

1. Motor Assembly

2. Receiver

6

6A

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver Hanger

Bracket

1

2

FH-W1811

Aviator Flush Instructions16

7. Finishing the Installation

1. Secure all wire connections with supplied wire ties to assist in

fan installation.

2. Tuck connections neatly into ceiling outlet box.

3. Remove the motor assembly from the hook on the mounting

bracket. Position the motor up to the mounting bracket and attach

using four screws in the top of the motor housing and attach

the housing to with the four set screws as shown. (Fig. 7).

Use Part F.

NOTE: Make sure the receiver sits flat and does not

interfere with the hook.

FH-W1811 Aviator Flush Instructions 17

7

FH-W1811

Aviator Flush Instructions18

8. Installing the Optional Wall Control

NOTE: Wall Control is not included. An additional bluetooth wall

controls accessory can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 8).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 8).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 8).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 8).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 8A) .

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 8A).

7. Fasten the wall plate to the wall mounting plate (Fig. 8A).

8

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)

Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

to Fan

From Breaker

* Home Wiring may vary

FH-W1811 Aviator Flush Instructions 19

8A

Multi-location wiring

1 2 3

54

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wallplate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 22.

Line/Hot

Red

Green (Green or Bare)

Wallcontroller 1 Wallcontroller 2 Wallcontroller 3

If Applicable

FAN

Neutral/White

Wall Control 1 Wall Control 2 Wall Control 3

FH-W1811

Aviator Flush Instructions20

9. Installing the LED Luminaire Module (Optional)

WARNING: Before starting installation, disconnect the power

by turning oﬀ the circuit breaker or removing the fuse at fuse box.

1. Unthread and remove the decorative lower cap from the

motor assembly.

2. Remove the 3 screws from the wire housing lower cover and

keep them for use with the light kit adapter plate. Remove the

wire housing lower cover.

3. Install the light kit adapter plate to the mounting ring using the

3 screws previously removed.

4. Raise and hold the LED luminaire module close to the adapter plate

and proceed to secure the wire connections. Connect the white wire

connector from the LED luminaire module to the white wire of the fan.

Follow the same procedure with the black wire connectors.

5. Tuck connections neatly into adapter plate. Using the 3 screws

provided, install the LED luminaire module to the adapter plate.

(Fig. 9B).

6. Raise glass shade up against the luminaire module, and

secure it to fan by turning glass shade clockwise until snug.

Do not overtighten (Fig. 9C)

LED Luminaire Installation

(F-1811-LED) Sold separately

La page charge ...

Modern Forms FH-W1811 Aviator Flush Mode d'emploi

Modern Forms FH-W1811 Aviator Flush Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents