Modern Forms FH-W1811 Aviator Flush Mode d'emploi

Catégorie
Ventilateurs ménagers
Taper
Mode d'emploi
Aviator Flush
Installation Instructions
works with the
Google Assistant
FH-W1811
Aviator Flush Instructions2
Please read and
save these instructions
before installation
DO NOT RETURN TO STORE
FH-W1811Aviator Flush Instructions 3
For all questions about your ceiling fan please read all included
instructions, installation procedures, troubleshooting guidelines
and warranty information before starting installation.
For missing parts or general inquiries call our trained technical staff at:
1-866-810-6615 option 1
MON-FRI 8AM-8PM EST
Email: customerservice@modernforms.com
Or live chat at modernforms.com
For fast service have the following information below when you call:
1. Model Name and Number
2. Part Number and Part Description
3. Date Of Purchase and Purchase Location
1-866-810-6615 option 2
MON-FRI 8AM-8PM EST
Email: fansupport@modernforms.com
General Inquiries
Fan Support
FH-W1811
Aviator Flush Instructions4
For operation, maintenance, and troubleshooting information,
visit http://modernforms.com/fan-support/
To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker
before beginning. All wiring must be in accordance with the National Electrical Code ANSI/NFPA
70” and local electrical codes. Electrical installation should be performed by a licensed electrician.
The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of
the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the
surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or
damage to the fan and other items, please be cautious when working around or cleaning the fan.
To avoid electrical shock or damage to the motor or finish, do not use water or chemicals
when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable
for most cleaning.
After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into the outlet box. The wires should be spread apart with the grounded conductor and
the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor
on the other side of the outlet box.
All set screws must be checked and re-tightened
where necessary before installation.
Safety Rules
FH-W1811 Aviator Flush Instructions 5
WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product
is designed for use only with the supplied parts and/or accessories designated for use with this
product by Modern Forms. Substitution of parts or accessories not designated for use with this
product by Modern Forms could result in personal injury or property damage and will void the
warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
WARNING: To reduce the risk of electric shock, this fan must
be installed and operated with the supplied wall control, or controlled from the Modern Forms app
or Wi-Fi Touch Panel Wall Control (not included).
WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in
improper assembly which can lead to noise or fan damage,personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the
brackets, balancing the blades or cleaning the fan.
WARNING: Do not insert foreign objects between rotating fan blades.
WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur
WARNING: This appliance is not intended for use by young children without supervision.
WARNING: To reduce the risk of fire, electric shock, personal injury or damage to the fan or other
items, the outlet box and support structure must be securely mounted and capable of reliably
supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN
SUPPORT. Use only the screws and washers provided with the outlet box.
CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“
section. If you feel you do not have enough wiring knowledge or experience, have your fan
installed by a licensed electrician.
NOTE: Before servicing or cleaning the fan, switch power off at the circuit breaker.
FH-W1811
Aviator Flush Instructions6
Get Smart...
Integrates
seamlessly with:
devices you already own
works with the
Google Assistant
Premium smart
features:
Accessories:
DC
MOTOR
complement high quality materials
personalize your experience
Quiet, reliable, and up to 70%
PRUHHɝFLHQWWKDQ$&IDQV
:L)LDQG%OXHWRRWKHQDEOHG
IRUȵH[LEOHFRQWURO
%OXHWRRWK:DOO&RQWURO
'LPVOLJKWWR_212))
IDQVSHHGV_6ROGVHSDUDWHO\
F-WCBT-WT :KLWH
%OXHWRRWK5HPRWH&RQWURO
'LPVOLJKWWR_212))
IDQVSHHGV
F-RCBT-WT :KLWH
Wet Location-listed to the strictest
UL/cUL safety regulations. Finished
and rated for interior and exterior use
FH-W1811 Aviator Flush Instructions 7
Contents
Tools Required
1. Mounting Options 10
2. Installing the Mounting Bracket 10
3. Attaching the Fan Blades 12
4. Attaching Decorative Lower Cap 12
5. Hanging the Fan 12
6. Making the Electrical Connections 14
7. Finishing the Installation 16
8. Installing the Wall Control 18
9. Installing the LED Luminaire Module (Optional) 20
10. Controlling the Fan 22
11. Reset 24
12. Breeze Mode 24
13. Application 24
14. Accessories 26
15. Troubleshooting 27-30
FH-W1811
Aviator Flush Instructions8
Package Contents
7. Control Receiver
w/Hardware
F-R3-1811-054
8. Remote Control w/Wire Nuts
F-RCBT-WT
Hardware Bag
RPL-AVIATORFH-PARTS
1. Blade Set of 3
RPL-F1811-54-BD-**
2. Blade Collector Ring
3. Mounting Bracket
RPL-F1811-HANGER-**
4. Hanger Gasket
5. Motor Assembly
6. Bottom Cap
RPL-F1811-54-CA-**
Before discarding packaging materials be certain all parts have been removed.
Place the parts from the hardware bag into a small container to keep them from being lost.
** denotes finish code of fan *** denotes blade sweep of fan
Part A
Part B
Part C
Part D
Part E
Part F
Hardware Bag
RPL-AVIATORFH-PARTS
#10 x 38mm Pan Head Phillip Screws (2)
#10x76mm Pan Head Phillip Wood Screws (1)
3/16 * 3/8 Flat Head Phillips Screw (5)
3/16”( 5.2x8.4x1.0mm) Spring Washer (1)
6.5x19x2mm Flat Washer (1)
3/16” Star Washer (2)
4*9 Flat Head Customed Philips Screw (10)
1/4”x16mm Phil/Slotted Pan Head Screw (7)
5 x 14 x 1mm Flat Washer (2)
B: Blade
C: Attach The Blade Collector Ring
To Blade
E: Wire Nuts
D: Safety Cable
F: Attach Housing to Mounting Bracket
(Found with the receiver)
Note: Some bags may contain extra parts for your convenience.
FH-W1811 Aviator Flush Instructions 9
1
8
4
5
2
6
7
3
IMPORTANT: Please make note
of the MAC ID on the
receiver and keep it in a
safe place.
MAC ID
Hanging Weight: OEV
F: Attach Housing to Mounting Bracket
FH-W1811
Aviator Flush Instructions10
1. Mounting Options
CAUTION: To prevent electrical shock, ensure electricity has been
turned off at the circuit breaker before beginning.
If there isn’t an existing UL/cUL listed outlet box, please refer to the
following instructions. Secure the outlet box directly to the building
structure. Use appropriate fasteners and building materials. The
outlet box and support structure must be able to fully support the
moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic
outlet boxes. Use only UL/cUL listed outlet boxes marked
“FOR FAN SUPPORT.
Secure the outlet box directly to the building structure. Use Part A if
needed.
Figures 1-1B are examples of different ways to mount the
outlet box.
NOTE: To hang your fan where there is an existing fixture but no
ceiling joist, you may need an installation hanger bar.
1. Disconnect power to the fan location at the breaker. A licensed
electrician must install the fan.
2. Pass the 120-volt supply wires through the center hole in the
ceiling mounting bracket as shown (Fig. 2). Secure the hanger
plate and hanger gasket to the ceiling outlet box with the screws
and washers that come included with your outlet box. (Fig. 2).
REMEMBER to turn off power at the breaker.
Follow the steps below to hang your fan properly:
2. Installing the Mounting Bracket
FH-W1811 Aviator Flush Instructions 11
1
1A
1B
2
2
1
2
2
3
1. Support Brace
2. Outlet Box
3. Joist
FH-W1811
Aviator Flush Instructions12
1. Pass supply wires through mounting plate.
2. Lift motor assemby and hang it on the hook on the
mounting plate using one of the screw holes (Fig.5).
3. Secure the safety cable into the structure beams using the wood
screw, washers, and spring washers provided (Fig. 5).
NOTE: A Safety cable is required for all installations in Canada. Safety
cable is required for ceiling fan and light combinations over
35 lbs. in both flush and downrod models in the United States.
5. Hanging the Fan
3. Attaching the Fan Blades
4. Attaching Decorative Lower Cap
1. Place blade on motor as shown (Fig. 3) and secure with the
blade attachment screws. Use Part B.
2. Repeat this procedure with the remaining blades (Fig. 3).
3. Secure the bottom of the blades together using the provided
blade collector ring and hardware (Fig. 3A). Use Part C.
1. Tightly twist the decorative lower cap onto the
motor assembly (Fig. 4).
(Skip this step if you purchased the optional luminaire)
FH-W1811 Aviator Flush Instructions 13
3
4
3A
5
FH-W1811
Aviator Flush Instructions14
6. Making the Electrical Connections
WARNING: Installation of this fan requires that a three-conductor
cable (including ground wire) which should run between ceiling and
wall outlet box.
WARNING: Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire nuts,
except for the ground wire.
Insert the receiver into the motor assembly with the flat side of the
receiver facing the ceiling (Fig. 6).
Motor to Receiver & Receiver to house supply wires (Fig. 6A).
1. Connect the motor assembly ground wire, mounting bracket
ground wire and receiver ground wire to the ground wire in
outlet box.
WARNING: Failure to connect ground wires could result in
poor fan control functionality.
Failure to make proper color-coded connections may reslult in
damage to your receiver.Connect the red wire from the fan to the red
wire marked
TO MOTOR from the receiver.
2. Connect the grey wire from the fan to the grey wire marked
TO MOTOR from the receiver.
3. Connect the yellow wire from the fan to the yellow wire marked
TO MOTOR from the receiver.
4. Connect the white wire from the fan to the white wire marked
FOR LIGHT from the receiver.
5. Connect the blue wire from the fan to the blue wire marked
FOR LIGHT from the receiver.
6. Connect the black (hot) wire from the ceiling to the black wire
marked AC in L from the receiver.
7. Connect the white (neutral) wire from the ceiling to the white
wire marked AC in N from the receiver.
NOTE: If you are not installing the optional luminaire module - cap off
white wires marked “FOR LIGHT” and blue wires marked “FOR LIGHT”
from receiver and corresponding wires from fan with wire nuts and
electrical tape.
FH-W1811 Aviator Flush Instructions 15
Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.
Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.
1. Motor Assembly
2. Receiver
6
6A
Black(Hot)
can be RED from Switch leg
Black(Line in H)
RED(to Motor)
GREEN(Ground)
BLUE (to Light)
BLUE (for Light)
GREEN(GND Must Use)
GREEN(Hanger Bracket Ground)
GREEN(Hanger Bracket Ground)
RED(to Motor)
GREY(to Motor)
WHITE(Neutral)
WHITE(to Light)
WHITE(Neutral)
GREY(to Motor)
YELLOW(to Motor)
WHITE(Line in N)
YELLOW(to Motor)
Outlet
Box
Receiver Hanger
Bracket
1
2
FH-W1811
Aviator Flush Instructions16
7. Finishing the Installation
1. Secure all wire connections with supplied wire ties to assist in
fan installation.
2. Tuck connections neatly into ceiling outlet box.
3. Remove the motor assembly from the hook on the mounting
bracket. Position the motor up to the mounting bracket and attach
using four screws in the top of the motor housing and attach
the housing to with the four set screws as shown. (Fig. 7).
Use Part F.
NOTE: Make sure the receiver sits flat and does not
interfere with the hook.
FH-W1811 Aviator Flush Instructions 17
7
FH-W1811
Aviator Flush Instructions18
8. Installing the Optional Wall Control
NOTE: Wall Control is not included. An additional bluetooth wall
controls accessory can be purchased separately.
1. Connect the green wire marked “GROUND from the wall
control to the copper wire from the wall outlet box that
feeds back to the circuit breaker – important for proper
fan function (Fig. 8).
2. Connect the black wire marked “LINE IN” from the wall control to
the black LINE VOLTAGE wire from the wall outlet box that feeds
back to the circuit breaker (Fig. 8).
3. Connect the red wire from the wall control to the black wire from
the wall outlet box that feeds up to the fan (Fig. 8).
4. Connect the white wire from the wall control to the white
(neutral) wire from the wall outlet box (Fig. 8).
5. Carefully tuck the wire connections inside the outlet box.
Secure the wall control with the two (2) wall control screws
provided (Fig. 8A) .
6. Attach the wall mounting plate over the wall switch and secure
with the two (2) wall mounting plate screws provided (Fig. 8A).
7. Fasten the wall plate to the wall mounting plate (Fig. 8A).
8
Wall Switch WiresHouse Wires
(Hot In)
(Neutral)
(Ground)
(Hot out to Fan)
Fan Switch leg
(Copper/Ground)
(Neutral)
(Hot)
to Fan
From Breaker
* Home Wiring may vary
FH-W1811 Aviator Flush Instructions 19
8A
Multi-location wiring
1 2 3
54
1. Wall Outlet
2. Wall Control
3. Wall Mounting Plate
4. Mounting Plate Screws
5. Wallplate
Individually pair each of the wall controls with the fan
receiver using the pairing instruction. See page 22.
Line/Hot
Red
Green (Green or Bare)
Wallcontroller 1 Wallcontroller 2 Wallcontroller 3
If Applicable
FAN
Neutral/White
Wall Control 1 Wall Control 2 Wall Control 3
FH-W1811
Aviator Flush Instructions20
9. Installing the LED Luminaire Module (Optional)
WARNING: Before starting installation, disconnect the power
by turning off the circuit breaker or removing the fuse at fuse box.
1. Unthread and remove the decorative lower cap from the
motor assembly.
2. Remove the 3 screws from the wire housing lower cover and
keep them for use with the light kit adapter plate. Remove the
wire housing lower cover.
3. Install the light kit adapter plate to the mounting ring using the
3 screws previously removed.
4. Raise and hold the LED luminaire module close to the adapter plate
and proceed to secure the wire connections. Connect the white wire
connector from the LED luminaire module to the white wire of the fan.
Follow the same procedure with the black wire connectors.
5. Tuck connections neatly into adapter plate. Using the 3 screws
provided, install the LED luminaire module to the adapter plate.
(Fig. 9B).
6. Raise glass shade up against the luminaire module, and
secure it to fan by turning glass shade clockwise until snug.
Do not overtighten (Fig. 9C)
LED Luminaire Installation
(F-1811-LED) Sold separately
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Modern Forms FH-W1811 Aviator Flush Mode d'emploi

Catégorie
Ventilateurs ménagers
Taper
Mode d'emploi