Axis Fixed Dome Network Camera AXIS P3301-V Manuel utilisateur

ENGLISH DEUTSCH ITALIANO ESPAÑOL

INSTALLATION GUIDE

FRAN

Ç

AIS

AXIS P3301 Fixed Dome Network Camera

AXIS P3301-V Fixed Dome Network Camera

About this Document

This document includes instructions for installing the

AXIS P3301/-V on your network. Previous experience of

networking will be beneficial when installing the

product.

Legal Considerations

Video and audio surveillance can be prohibited by laws

that vary from country to country. Check the laws in

your local region before using this product for

surveillance purposes.

This product includes one (1) H.264 decoder license. To

purchase further licenses, contact your reseller.

Electromagnetic Compatibility (EMC)

This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a

particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures: Re-orient or relocate

the receiving antenna. Increase the separation between

the equipment and receiver. Connect the equipment to

an outlet on a different circuit to the receiver. Consult

your dealer or an experienced radio/TV technician for

help. Shielded (STP) network cables must be used with

this unit to ensure compliance with EMC standards.

USA - This equipment has been tested and found to

comply with the limits for a Class B computing device

pursuant to Subpart B of Part 15 of FCC rules, which are

designed to provide reasonable protection against such

interference when operated in a commercial

environment. Operation of this equipment in a

residential area is likely to cause interference, in which

case the user at his/her own expense will be required to

take whatever measures may be required to correct the

interference.

Canada - This Class B digital apparatus complies with

Canadian ICES-003.

Europe - This digital equipment fulfills the

requirements for radiated emission according to limit B

of EN55022, and the requirements for immunity

according to EN55024 residential and commercial

industry.

Japan - This is a class B product based on the standard

of the Voluntary Control Council for Interference from

Information Technology Equipment (VCCI). If this is used

near a radio or television receiver in a domestic

environment, it may cause radio interference. Install and

use the equipment according to the instruction manual.

Australia - This electronic device meets the

requirements of the Radio communications

(Electromagnetic Compatibility) Standard AS/NZS

CISPR22.

Equipment Modifications

This equipment must be installed and used in strict

accordance with the instructions given in the user

documentation. This equipment contains no

user-serviceable components. Unauthorized equipment

changes or modifications will invalidate all applicable

regulatory certifications and approvals.

Liability

Every care has been taken in the preparation of this

document. Please inform your local Axis office of any

inaccuracies or omissions. Axis Communications AB

cannot be held responsible for any technical or

typographical errors and reserves the right to make

changes to the product and documentation without

prior notice. Axis Communications AB makes no

warranty of any kind with regard to the material

contained within this document, including, but not

limited to, the implied warranties of merchantability

and fitness for a particular purpose. Axis

Communications AB shall not be liable nor responsible

for incidental or consequential damages in connection

with the furnishing, performance or use of this material.

RoHS

This product complies with both the European

RoHS directive, 2002/95/EC, and the Chinese

RoHS regulations, ACPEIP.

WEEE Directive

The European Union has enacted a Directive

2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE Directive). This directive is

applicable in the European Union member

states.

The WEEE marking on this product (see right) or its

documentation indicates that the product must not be

disposed of together with household waste. To prevent

possible harm to human health and/or the environment,

the product must be disposed of in an approved and

environmentally safe recycling process. For further

information on how to dispose of this product correctly,

contact the product supplier, or the local authority

responsible for waste disposal in your area.

Business users should contact the product supplier for

information on how to dispose of this product correctly.

This product should not be mixed with other commercial

waste. For more information, visit

www.axis.com/techsup/commercial waste.

Support

Should you require any technical assistance, please

contact your Axis reseller. If your questions cannot be

answered immediately, your reseller will forward your

queries through the appropriate channels to ensure a

rapid response. If you are connected to the Internet, you

can:

• download user documentation and firmware updates

• find answers to resolved problems in the FAQ database.

Search by product, category, or phrases

• report problems to Axis support by logging in to your

private support area.

The AXIS P3301/-V uses a 3.0V CR2032 Lithium

battery, for more information please see page 73.

AXIS P3301/-V Installation Guide Page 3

ENGLISH

AXIS P3301/-V Installation Guide

This installation guide provides instructions for installing the AXIS P3301 / AXIS P3301-V Fixed

Dome Network Camera on your network. For all other aspects of using the product, please see the

User’s Manual, available on the CD included in this package, or from www.axis.com/techsup

Installation steps

1. Check the package contents against the list below.

2. Hardware overview. See page 4.

3. Install the hardware. See page 5.

4. Assign an IP address. See page 6.

5. Set the password. See page 9.

6. Adjust the focus. See page 11.

7. Complete the installation. See page 11.

Package contents

Item Models/variants/notes

Fixed Dome Network camera AXIS P3301 - Tamper-resistant casing

AXIS P3301-V - Vandal-resistant casing

PS-H indoor power supply

(country specific)

Europe

UK

Australia

USA/Japan

Argentina

Korea

Terminal block connector 4-pin connector block for connecting external devices to the I/O terminal

connector

Mounting kit Screwdriver for tamper-proof screws

Tamper-proof screws

Drill template

CD AXIS Network Video Product CD, including product documentation,

installation tools and other software

Printed Materials AXIS P3301/-V Installation Guide (this document)

Axis Warranty Document

Important!

This product must be used in

compliance with local laws and

regulations.

Page 4 AXIS P3301/-V Installation Guide

Hardware overview

Product ID & Serial number (S/N).

The serial number may be

required during the installation.

Dimensions

HxWxD = 94 x 144 x 132mm (3.7" x 5.7" x 5.2")

Weight AXIS P3301 = 425g (0.94 lb) power supply excl.

Weight AXIS P3301-V = 580g (1.28 lb) power supply excl.

Cover plates

Network

indicator LED

Status

indicator

LED

Control button

Power connector

see page 13

Network connector

see page 13

Power

indicator LED Audio out Audio in

Microphone

16mm cable conduit

(not supplied) fitted

to AXIS P3301-V

I/O terminal

connector

see page 13

AXIS P3301/-V Installation Guide Page 5

ENGLISH

Install the hardware

Mount the camera

The AXIS P3301/-V can be mounted with the cables routed through the wall/ceiling, or from above

or below. There are cover plates for the openings on both sides of the dome cover.

The AXIS P3301/-V can also be fitted with a metal conduit for protecting the cabling when

connected via the side openings. See the illustrations on page 4.

1. Using the drill template, drill two holes in the ceiling/wall. Ensure the camera is positioned so

that the tamper-proof screws can be tightened using the supplied screwdriver.

2. Route the required cables. See Connect the cables, on page 6 for details.

3. Fasten the camera unit to a ceiling or wall, using screws and plugs appropriate for the ceiling/

wall material.

4. Proceed to Connect the cables, on page 6.

Mounting on a hard ceiling

To mount the AXIS P3301/-V on a hard ceiling, check that the ceiling material is sturdy enough to

hold the weight of the camera.

The camera can also be secured using a plate or board that better carries the weight of the camera,

and which is more suitable for securing the screws.

The AXIS P3301/-V can also be mounted using the AXIS P3301/-V Drop Ceiling Mount, which allows

the camera to be mounted more discreetly. Please see www.axis.com for all available mounting

accessories.

!IMPORTANT! - The casing of the AXIS P3301-V is not approved for outdoor use - the

product may only be installed in indoor environments.

Plate or

Ceiling

AXIS P3301/-V

Screws

board

Page 6 AXIS P3301/-V Installation Guide

Connect the cables

1. Optionally connect external input/output devices, e.g. alarm devices. See page 13 for informa-

tion on the terminal connector pins.

2. Optionally connect an active speaker and/or external microphone.

3. Connect the camera to the network using a shielded network cable.

4. Connect power, using one of the methods listed below:

• PoE (Power over Ethernet, Class 2). If available, this is automatically detected when the

network cable is connected.

• Connect the supplied indoor power supply to the power connector on the camera.

5. Check that the indicator LEDs indicate the correct conditions. See the table on page 14 for

further details. Note that some LEDs can be disabled and may be unlit.

Assign an IP address

Most networks today have a DHCP server that automatically assigns IP addresses to connected

devices. If your network does not have a DHCP server the AXIS P3301/-V will use 192.168.0.90 as

the default IP address.

If you would like to assign a static IP address, the recommended method in Windows is either AXIS

IP Utility or AXIS Camera Management. Depending on the number of cameras you wish to install,

use the method that best suits your purpose.

Both of these free applications are available on the Axis Network Video Product CD supplied with

this product, or they can be downloaded from www.axis.com/techsup

Notes:

• If assigning the IP address fails, check that there is no firewall blocking the operation.

• For other methods of assigning or discovering the IP address of the AXIS P3301/-V, e.g. in other

operating systems, see page 12.

Method Recommended for Operating system

AXIS IP Utility

See page 7

Single camera

Small installations

Windows

AXIS Camera Management

See page 8

Multiple cameras

Large installations

Installation on a different subnet

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

AXIS P3301/-V Installation Guide Page 7

ENGLISH

AXIS IP Utility - single camera/small installation

AXIS IP Utility automatically discovers and displays Axis devices on your network. The application

can also be used to manually assign a static IP address

.

Note that the computer running AXIS IP Utility must be on the same network segment (physical

subnet) as the AXIS P3301/-V.

Automatic discovery

1. Check that the AXIS P3301/-V is connected to the network and that power has been applied.

2. Start AXIS IP Utility.

3. When the camera appears in the window, double-click it to open its home page.

4. See page 9 for instructions on how to assign the password.

Assign the IP address manually (optional)

1. Acquire an unused IP address on the same network segment as your computer.

2. Select the AXIS P3301 in the list.

3. Click the button Assign new IP address to the selected device and enter the IP address.

4. Click the Assign button and follow the on-screen instructions. Note that the camera must be

restarted within 2 minutes for the new IP address to be set.

5. Click the Home Page button to access the camera’s web pages.

6. See page 9 for instructions on how to set the password.

Note:

AXIS P3301-V will display in AXIS IP Utility as AXIS P3301.

Page 8 AXIS P3301/-V Installation Guide

AXIS Camera Management - multiple cameras/large installations

AXIS Camera Management can automatically discover multiple Axis devices, show connection

status, manage firmware upgrades and set IP addresses.

Automatic discovery

1. Check that the camera is connected to the network and that power has been applied.

2. Start AXIS Camera Management. When the AXIS P3301/-V appears in the window, double-click

it to open the camera’s home page.

3. See page 9 for instructions on how to set the password.

Assign an IP address in a single device

1. Select AXIS P3301 in AXIS Camera Management and click the

Assign IP button.

2. Select Assign the following IP address and enter the IP

address, subnet mask and default router the device will use.

3. Click the OK button.

Assign IP addresses in multiple devices

AXIS Camera Management speeds up the process of assigning IP

addresses to multiple devices, by suggesting IP addresses from a

specified range.

1. Select the devices you wish to configure (different models can

be selected) and click the Assign IP button.

2. Select Assign the following IP address range and enter the

range of IP addresses, the subnet mask and default router the

devices will use.

3. Click the OK button.

Note:

AXIS P3301-V will display in AXIS Camera Management as AXIS P3301.

AXIS P3301/-V Installation Guide Page 9

ENGLISH

Set the password

To gain access to the product, the password for the default administrator user root must be set. This

is done in the ‘Configure Root Password’ dialog, which is displayed when the AXIS P3301/-V is

accessed for the first time.

To prevent network eavesdropping when setting the root password, this can be done via an

encrypted HTTPS connection, which requires an HTTPS certificate (see note below).

To set the password via a standard HTTP connection, enter it directly in the first dialog shown

below.

To set the password via an encrypted HTTPS connection, follow these steps:

1. Click the Create self-signed certificate button.

2. Provide the requested information and click OK. The certificate is created and the password can

now be set securely. All traffic to and from the AXIS P3301/-V is encrypted from this point on.

3. Enter a password and then re-enter it to confirm the spelling. Click OK. The password has now

been configured.

4. To log in, enter the user name “root” in the dialog as requested

Note: The default administrator user name root cannot be deleted.

5. Enter the password as set above, and click OK.

To configure the password directly

via an unencrypted connection, enter

the password here.

To create an HTTPS connection,

start by clicking this button.

Page 10 AXIS P3301/-V Installation Guide

Access the video stream

The Live View page of the AXIS P3301/-V is displayed, with links to the Setup tools, which allow you

to customize the camera.

If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream

in Internet Explorer. You will need administrator rights on the computer to do this.

Notes:

• HTTPS (Hypertext Transfer Protocol over Secure Socket Layer) is a protocol used to encrypt the traffic

between web browsers and servers. The HTTPS certificate controls the encrypted exchange of

information.

• The default administrator user root cannot be deleted.

• If the password for root is lost or forgotten, the AXIS P3301/-V must be reset to the factory default

settings. See Resetting to the Factory Default Settings, on page 15.

Setup - Provides all the tools for configuring

the camera to requirements.

Help - Displays

online help on all

aspects of using

the camera.

AXIS P3301/-V Installation Guide Page 11

ENGLISH

Adjust the image and focus

Open the Live View page in the web interface and make the following adjustments to the camera:

1. Loosen the locking screw and tilt adjust-

ment screws.

2. Turn the lens to the desired position.

3. Once satisfied, gently tighten the locking

screw and tilt adjustment screws to secure

the camera’s position.

4. Turn the image balance ring to set the

horizontal position.

5. Open the Focus Adjustment page in the

Web interface under Basic Configuration

> Focus and follow the on-screen

instructions. Use the image window to

adjust the focus and zoom.

6. To set the focus and zoom, loosen the

zoom and focus pullers anti-clockwise and

rotate the rings.

7. Lock the focus and zoom pullers in position

by rotating the screws clockwise.

Note:

Due to the dome’s refraction, the image may appear slightly out of focus once the dome

has been placed. Focus on an object slightly closer than the intended area to compensate

for this.

The image can also be fine-tuned for low light conditions.

Go to Setup > Video & Audio > Camera Settings in the camera’s web interface and see the online

help for more information.

Complete the installation

1. Rotate the black protective shield inside the dome casing to match the camera’s position.

2. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower to

remove dust from the lens.

3. Mount the dome casing using the supplied tamper-proof screws and screw driver.

4. Now that the dome is in place, double-check that the camera is properly focused.

5. The installation is now complete.

Image

Focus puller

Zoom puller

balance

ring

Locking screw

screw

Tilt adjustment

(on each side)

Page 12 AXIS P3301/-V Installation Guide

Other methods of setting the IP address

The table below shows the other methods available for setting or discovering the IP address. All

methods are enabled by default, and all can be disabled.

Set the IP address with ARP/Ping

1. Acquire an IP address on the same network segment your computer is connected to.

2. Locate the serial number (S/N) on the AXIS P3301/-V label.

3. Open a command prompt on your computer and enter the following commands:

4. Check that the network cable is connected to the camera and then start/restart the camera, by

disconnecting and reconnecting power.

5. Close the command prompt when you see ‘Reply from 192.168.0.125: ...’ or similar.

6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on

your keyboard.

Notes:

• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.

• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.

Use in operating

system

Notes

UPnP™ Windows

(ME or XP)

When enabled on your computer, the camera is automatically

detected and added to “My Network Places.”

Bonjour MAC OSX

(10.4 or later)

Applicable to browsers with support for Bonjour. Navigate to the

Bonjour bookmark in your browser (e.g. Safari) and click on the

link to access the camera’s web pages.

AXIS Dynamic DNS

Service

All A free service from Axis that allows you to quickly and simply

install your camera. Requires an Internet connection with no

HTTP proxy. See www.axiscam.net for more information.

ARP/Ping All See below. The command must be issued within 2 minutes of

connecting power to the camera.

View DHCP server

admin pages

All To view the admin pages for the network DHCP server, see the

server’s own documentation.

Windows syntax: Windows example:

arp -s <IP Address> <Serial Number>

ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00

ping -l 408 -t 192.168.0.125

UNIX/Linux/Mac syntax: UNIX/Linux/Mac example:

arp -s <IP Address> <Serial Number> temp

ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00 temp

ping -s 408 192.168.0.125

AXIS P3301/-V Installation Guide Page 13

ENGLISH

Unit connectors

Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using shielded

cables is recommended.

Power connector - Mini DC connector. 5.1V DC, max 4.0W. See product label for ± connection.

Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from

a stereo signal).

Audio out - Audio output (line level) that can be connected to a public address (PA) system or an

active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo

connector must be used for the audio out.

I/O terminal connector - Used in applications for e.g. motion detection,

event triggering, time lapse recording and alarm notifications. It provides the

interface to:

• 1 transistor output - For connecting external devices such as relays and LEDs. Connected

devices can be activated by the VAPIX Application Programming Interface (API), by the out-

put buttons on the Live View page or by an Event Type. The output will show as active

(shown under Event Configuration > Port Status) if the alarm device is activated.

• 1 digital input - An alarm input for connecting devices that can toggle between an open

and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc.

When a signal is received the state changes and the input becomes active (shown under

Event Configuration > Port Status).

• Auxiliary power and GND

Function Pin Notes Specifications

GND 1 Ground

3.3V DC

Power

2 Can be used to power auxiliary equipment.

Note: This pin can only be used as power out.

Max. load = 50mA

Digital

Input

3 Connect to GND to activate, or leave floating

(or unconnected) to deactivate.

Min. input= - 40V DC

Max. input= + 40V DC

Digital

Output

4 Uses an open-drain NFET transistor with the

source connected to GND. If used with an

external relay, a diode must be connected in

parallel with the load, for protection against

voltage transients.

Max. load = 100mA

Max voltage = + 40V DC

Page 14 AXIS P3301/-V Installation Guide

Connection diagram

LED indicators

LED Color Indication

Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.

Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.

Unlit No network connection.

Status Green Steady green for normal operation.

Note: The Status LED can be configured to be unlit during normal operation, or to

flash only when the camera is accessed. To configure, go to Setup > System

Options > LED. See the online help files for more information.

Amber Steady during startup, during reset to factory default or when restoring settings.

Red Slow flash for failed upgrade.

Power Green Normal operation.

Amber Flashes green/amber during firmware upgrade.

o

z

AXIS P3301/-V

3.3V

max. 50mA

e.g. pushbutton

4

o

3

o

2

1

D

S

G

AXIS P3301/-V Installation Guide Page 15

ENGLISH

Resetting to the Factory Default Settings

This will reset all parameters, including the IP address, to the Factory Default settings:

1. Disconnect power from the camera.

2. Press and hold the Control button and reconnect power.

3. Keep the Control button pressed until the Power indicator flashes amber (this may take up to

15 seconds).

4. Release the Control button. When the Power indicator displays green (which can take up to 1

minute) the process is complete and the camera has been reset.

5. Re-assign the IP address, using one of the methods described in this document.

It is also possible to reset parameters to the original factory default settings via the web interface.

For more information, please see the online help or the user’s manual.

Accessing the camera from the Internet

Once installed, your AXIS P3301/-V is accessible on your local network (LAN). To access the camera

from the Internet, network routers must be configured to allow incoming traffic, which is usually

done on a specific port

• HTTP port (default port 80) for viewing and configuration

• RTSP port (default port 554) for viewing H.264 video streams

Please refer to the documentation for your router for further instructions. For more information on

this and other topics, visit the Axis Support Web at www.axis.com/techsup

Further information

The user’s manual is available from the Axis Web site at www.axis.com or from the Axis Network

Video Product CD supplied with this product.

Tip!

Visit www.axis.com/techsup to check if there is updated firmware available for your AXIS

P3301/-V. To see the currently installed firmware version, see Setup > About.

AXIS P3301/-V Guide d'installation Page 17

FRAN

Ç

AIS

AXIS P3301/-V Guide d'installation

Ce guide d'installation vous explique comment installer la AXIS P3301 / AXIS P3301-V Caméra

réseau à dôme fixe sur votre réseau. Pour d'autres informations sur l'utilisation de ce produit,

consultez le manuel de l'utilisateur, disponible sur le CD fourni, ou visitez le site www.axis.com/

techsup.

Étapes de l'installation

1. Vérifiez le contenu de la livraison à l'aide de la liste ci-dessous.

2. Présentation du matériel. Reportez-vous à la page 18.

3. Installez le matériel. Reportez-vous à la page 19.

4. Paramétrez une adresse IP. Reportez-vous à la page 20.

5. Définissez le mot de passe. Reportez-vous à la page 23.

6. Réglez la mise au point. Reportez-vous à la page 25.

7. Terminez l'installation. Reportez-vous à la page 25.

Contenu de l'emballage

Article Modèles/variantes/remarques

Caméra réseau à dôme fixe AXIS P3301 - Boîtier inviolable

AXIS P3301-V - Boîtier anti-effraction

Alimentation intérieure PS-H

(dépend du pays)

Europe

Royaume-Uni

Australie

États-Unis/Japon

Argentine

Corée

Connecteur pour terminaux Connecteur 4 broches pour la connexion d'équipements externes au

connecteur

E/S

Kit de montage Tournevis pour vis inviolables

Vis inviolables

Gabarit de perçage

CD CD de la caméra vidéo réseau Axis comprenant la documentation,

les outils d'installation et les autres logiciels

Documentation Guide d'installation de la caméra AXIS P3301/-V (le présent document)

Document de garantie d'Axis

Important !

Ce produit doit être utilisé

conformément aux lois et

dispositions locales en vigueur.

Page 18 AXIS P3301/-V Guide d'installation

Présentation du matériel

ID du produit et numéro de série (S/N).

Le numéro de série peut

être demandé pendant l'installation.

Dimensions

H x L x P = 94 x 144 x 132mm

Poids de la caméra AXIS P3301= 425g (alimentation exclue)

Poids de la caméra AXIS P3301-V= 580g (alimentation exclue)

Plaques

d'obturation

Témoin DEL réseau

Témoin

DEL

d'état

Bouton de

commande

Connecteur

d’alimentation

Reportez-vous à

la page 28

Connecteur

deréseau

Reportez-vous

à la page 28

Témoin DEL

d’alimentation

Sortie

audio Entrée

audio

Microphone

conduit de câbles 16 mm

(non fourni) installé

AXIS P3301-V

Connecteur pour

terminaux E/S

Reportez-vous à

la page 28

AXIS P3301/-V Guide d'installation Page 19

FRAN

Ç

AIS

Installation du matériel

Montage de la caméra

La caméra AXIS P3301/-V peut être montée avec les câbles d'alimentation et réseau acheminés

dans le mur/plafond, ou depuis le haut ou le bas. Vous disposez de plaques d'obturation pour les

ouvertures des deux côtés du capot du dôme.

La caméra AXIS P3301/-V peut être également dotée d'un conduit métallique pour protéger les

câbles lors d'une connexion par les ouvertures latérales. Consultez les figures de la page 18.

1. Avec le gabarit de perçage, percez deux trous dans le plafond/mur. Veillez à ce que la caméra

soit positionnée de telle manière que les vis inviolables puissent être serrées à l'aide du

tournevis fourni.

2. Orientez les câbles nécessaires. Pour plus d'informations, consultez la section Branchement des

câbles, page 20.

3. Fixez la caméra au plafond ou au mur à l'aide des vis et des chevilles appropriées.

4. Passez à la section Branchement des câbles, page 20.

Montage sur plafond dur

Pour monter la caméra AXIS P3301/-V sur un plafond dur, vérifiez que le matériau du plafond est

assez solide pour supporter le poids de la caméra.

La caméral peut être également fixée à l'aide d'une plaque ou d'une planche qui supporte mieux le

poids de la caméra et qui peut être plus adaptée pour la fixation des vis.

La caméra AXIS P3301/-V peut être également montée à l'aide du AXIS P3301/-V kit de montage

pour faux-plafond, qui permet un montage plus discret. Voir www.axis.com pour les accessoires de

montage disponibles.

!IMPORTANT ! - Le boitier de l'AXIS P3301-V n'est pas approuvé pour une utilisation

extérieure - Le produit doit être uniquement installé en intérieur.

Plaque ou

Plafond

AXIS P3301/-V

Vis

planche

Page 20 AXIS P3301/-V Guide d'installation

Branchement des câbles

1. Si vous le souhaitez, connectez des dispositifs externes, par exemple des dispositifs d'alarme.

Reportez-vous à la page 28 pour plus d'informations sur les broches du connecteur pour

terminaux.

2. Si vous le souhaitez, connectez un haut-parleur actif et/ou un micro externe.

3. Connectez la caméra à votre réseau à l'aide d'un câble de réseau blindé.

4. Branchez l'alimentation à l'aide de l'une des méthodes reprises ci-dessous.

• PoE (Alimentation éléctrique par câble Ethernet, classe 2). Si disponible, ceci est

automatiquement détecté quand le câble résau est connecté.

• Branchez l'alimentation intérieure fournie au connecteur d'alimentation de la caméra.

5. Vérifiez que les témoins DEL indiquent les conditions correctes. Pour plus d'informations,

consultez le tableau à la page 29. Notez que certains témoins DEL peuvent être désactivés et

éteints.

Paramétrage d'une adresse IP

Aujourd'hui, la plupart des réseaux comportent un serveur DHCP qui paramètre automatiquement

des adresses IP aux dispositifs connectés. Si ce n'est pas le cas de votre réseau, la caméra AXIS

P3301/-V utilisera l'adresse IP par défaut 192.168.0.90.

Si vous souhaitez paramétrer une adresse IP statique, sous Windows nous recommandons

l'utilisation de l'application AXIS IP Utility ou de l'application AXIS Camera Management. Selon le

nombre de caméras à installer, utilisez la méthode qui vous convient le mieux.

Ces deux applications gratuites sont disponibles sur le CD de la caméra vidéo réseau Axis fourni

avec ce produit. Vous pouvez également les télécharger à partir du site www.axis.com/techsup.

Remarques :

• En cas d'échec de l'attribution de l'adresse IP, vérifiez qu'aucun pare-feu ne bloque l'opération.

• Pour connaître les autres méthodes d'affectation ou de repérage de l'adresse IP de la caméra AXIS

P3301/-V, par exemple sur d'autres systèmes d'exploitation, reportez-vous à la page 26.

Méthode Recommandée pour Système

d'exploitation

AXIS IP Utility

Voir page 21

Une seule caméra

Les petites installations

Windows

AXIS Camera Management

Voir page 22

Plusieurs caméras

Les grandes installations

Installation sur un autre sous-

réseau

Windows 2000

Windows XP Pro

Windows 2003 Server

Windows Vista

La page charge ...

Axis Fixed Dome Network Camera AXIS P3301-V Manuel utilisateur

Ce manuel convient également à

Axis Fixed Dome Network Camera AXIS P3301-V Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents