Maytag Commercial MLE20PDCYW Guide d'installation

INSTALLATION

INSTRUCTIONS

CommerCial StaCked WaSher/dryer

GaS or eleCtriC

www.maytagcommerciallaundry.com

W10045641B

INSTRUCTIONS

D’INSTALLATION

laveuSe/SéCheuSe SuperpoSéeS

à uSaGe CommerCial

à Gaz ou éleCtrique

INSTRUCCIONES

DE INSTALACIÓN

lavadora/SeCadora ComerCialeS

apiladaS a GaS o eléCtriCaS

TABLE OF CONTENTS

Page

Stacked Washer/Dryer Safety ............. 2

Tools & Parts ........................................ 5

Alternate Parts and Accessories ........ 6

Dimensions/Clearances ...................... 7

Stacked Washer/Gas Dryer

Installation Requirements ................... 8

Stacked Washer/Electric Dryer

Installation Requirements ................. 11

Dryer Venting Requirements ............ 15

Dryer Gas Supply Requirements ...... 18

Installing Stacked Washer/Dryer ...... 19

Washer Drain System ........................ 22

Electric Dryer Electrical

Connections ....................................... 23

Leveling ............................................... 27

Reversing Dryer Door Swing ............. 29

Stacked Washer/Dryer

Maintenance Instructions .................. 31

If You Need Assistance ...................... 32

Electronic Control Setup

Instructions ........................................ 33

Warranty ............................................. 39

TABLE DES MATIÈRES

Page

Sécurité de la laveuse/sécheuse

superposées ....................................... 40

Outils et pièces .................................. 43

Pièces supplémentaires

et accessoires .................................... 44

Dimensions/Distances

de dégagement .................................. 45

Exigences d’installation pour

la laveuse/sécheuse à gaz

superposées ....................................... 46

Exigences d’installation pour la

laveuse/sécheuse électriques

superposées ..................................... 49

Exigences concernant

l’évacuation de la sécheuse ............. 54

Spécications de l’alimentation

en gaz de la sécheuse ....................... 57

Installation de la laveuse/sécheuse

superposées ...................................... 58

Système d’évacuation

de la laveuse ....................................... 61

Raccordements de la sécheuse

électrique ........................................... 62

Nivellement ......................................... 66

Inversion du sens d’ouverture

de la porte de la sécheuse ................. 68

Instructions d’entretien de la

laveuse/sécheuse superposées ....... 70

Si vous avez besoin d’assistance ..... 71

Instructions de réglage du tableau

de commande électronique .............. 72

Garantie .............................................. 79

ÍNDICE

Página

Seguridad de la lavadora/

secadora apiladas .............................. 80

Herramientas y piezas ....................... 83

Piezas y accesorios adicionales ...... 84

Dimensiones y espacios libres ......... 85

Requisitos de instalación de la

lavadora/secadora a gas apiladas ... 86

Requisitos de instalación de la

lavadora/secadora eléctricas

apiladas .............................................. 89

Requisitos de ventilación

de la secadora ................................... 94

Requisitos del suministro

de gas de la secadora ....................... 97

Instalación de la lavadora/

secadora apiladas .............................. 98

Sistema de desagüe

de la lavadora ................................... 101

Conexiones eléctricas

de la secadora eléctrica ................. 102

Nivelación .......................................... 106

Cómo invertir el cierre

de la puerta de la secadora ............. 108

Instrucciones de mantenimiento

de la lavadora/secadora apiladas ... 110

Si necesita ayuda ............................. 111

Instrucciones de programación

del control electrónico .................... 112

Garantía ............................................ 120

2

STACKED WASHER/DRYER SAFETY

n It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer

smells gas. This information should be obtained from your gas supplier.

n Post the following warning in a prominent location.

3

STACKED WASHER/DRYER SAFETY

4

STACKED WASHER/DRYER SAFETY

5

Parts Supplied:

water inlet hoses (2) inlet hose washers (4) U-shaped hose form transit bolt hole plug (4)

beaded tie strap

drain hose/clamp

Tools Needed:

8" (203 mm) 8" (203 mm) or 10" (254 mm) at-blade screwdriver phillips screwdriver

or 10" (254 mm) adjustable wrench

pipe wrench that opens to 1" (25 mm)

Torx

®†

T-20 security 1" (25 mm) hex-head 5⁄16" socket wrench pliers

screwdriver or bit socket wrench (that open to 1

9

/

16

" [39 mm])

level utility knife 1/4" (6 mm) nut driver locking pliers

caulk gun and caulk vent clamps pipe-joint compound 27" (686 mm) wood block

(for installing new exhaust vent) suitable for gas type

ashlight (optional) 1/2" (13 mm) and 9/16" ruler or measuring tape

(14 mm) open-end wrenches

TOOLS & PARTS

†® TORX is a registered trademark of Saturn Fasteners, Inc.

6

ALTERNATE PARTS AND ACCESSORIES

Alternate Parts

Your installation may require additional parts. If you are

interested in purchasing one of the items listed here, call

the toll-free number in the “If You Need Assistance” section.

If You Have You Will Need to Buy

Overhead sewer Standard 20 gal. (76 L) 39"

(990 mm) tall drain tub or utility

sink, sump pump and connectors

(available from local plumbing

suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm)

diameter Standpipe Adapter

Part Number 3363920

Connector Kit Part Number 285835

Drain hose too Extension Drain Hose Part

short Number 285863

Connector Kit Part Number 285835

Lint clogged drain Drain Protector Part Number 367031

Connector Kit Part Number 285835

Floor drain system Siphon break, Part Number 285834

Connector Kit (x2) Part Number

285835

Extension Drain Hose Part

Number 285863

Water faucets 2 longer water ll hoses:

beyond reach 6 ft. (1.8 m) 90° bend hose

of ll hoses Part Number 76314

10 ft. (3.0 m) Part Number 350008

Accessories

Enhance your washer/dryer with these premium accessories.

For more high-quality items or to order,

call 1-800-901-2042, or visit us at

www.maytag.com/accessories.

In Canada call: 1-800-807-6777 or visit us at

www.whirlpoolparts.ca.

Part Number Accessory

8212526 Washer drip tray, ts under all

31682 All-purpose appliance cleaner

1903WH Laundry supply storage cart

279818 3-way dryer venting kit

285834 Siphon break kit

7

DIMENSIONS/CLEARANCES

Front View Side View Back View

1"

(25 mm)

74"

(1880 mm)

51"

(1295 mm)

29 "

(751 mm)

1

/2

27"

(686 mm)

1"

(25 mm)

74"

(1880 mm)

Dimensions

Clearances

Side Clearances Back/Top Clearances

0"

(0 mm)

0"

(0 mm)

8

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room,

or recessed area. See “Drain System.”

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the washer/dryer where

it will be exposed to the weather. Do not store or operate the

washer/dryer in temperatures at or below 32°F (0°C). Some

water can remain in the washer and can cause damage in low

temperatures. Proper installation is your responsibility.

You will need:

n A water heater set to deliver 120°F (49°C) water to the

washer.

n

A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

n

Hot and cold water faucets located within 4 ft. (1.2 m) of the

hot and cold water ll valves, and water pressure of 20–100

psi (137.9–689.6 kPa).

n

A level oor with a maximum slope of 1" (25 mm) under

entire washer/dryer. Installing the washer/dryer on soft oor

surfaces, such as carpets or surfaces with foam backing,

is not recommended.

n

A sturdy and solid oor to support the washer/dryer with

a total weight (water and load) of 450 lbs (204 kg).

n

A oor drain under the bulkhead. Prefabricated bulkheads

with electrical outlets, water inlet lines, and drain facilities

should be used only where local codes permit.

Stacked Washer/Gas Dryer Location

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

Stacked washer/gas dryer installation clearances

n The location must be large enough to allow the washer

and dryer doors to be fully opened.

n

Additional spacing should be considered for ease of

installation and servicing. The doors open more than 180°.

The washer door is not revers ble.

n

Additional clearances might be required for wall, door, and

oor moldings.

n

Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

n

Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

n

Make sure that lower edges of the cabinet, plus the back and

bottom sides of the washer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

“Recessed Area Installation Instructions” below for minimum

spacing requirements.

Recessed Area Installation Instructions

This washer/dryer may be installed in a recessed area. For

recessed area installations, minimum clearances can be found

on the warning label on the rear of the dryer or in “Dimensions/

Clearances.”

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes and

ordinances.

The dryer must be exhausted outdoors.

9

Stacked Washer/Gas Dryer Grounding

IMPORTANT: The washer/dryer must be electrically grounded

in accordance with local codes and ordinances or, in the

absence of local codes, with the National Electrical Code,

ANSI/NFPA 70, latest edition, or Canadian Electrical Code, CSA

C22.1. If codes permit and a separate ground wire is used, it is

recommended that a qualied electrical installer determine

that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

n Do not ground to a gas pipe.

n Do not have a fuse in the neutral or ground circuit.

n A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this washer/dryer be provided.

n This washer/dryer is equipped with a power supply cord

having a 3-prong grounding plug.

n To minimize the possibility of shock, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualied electrician.

n If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

n Check with a qualied electrician if you are not sure the

washer/dryer is properly grounded.

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

Stacked Washer/Gas Dryer Electrical Requirements

10

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and

ordinances. In the absence of local codes, installation must

conform with American National Standard, National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this washer/dryer has been certied by CSA

International for use at altitudes up to 10,000 feet (3048 m)

above sea level at the B.T.U. rating indicated on the model/

serial plate. Burner input adjustments are not required when

the washer/dryer is operated up to this elevation.

When installed above 10,000 feet (3048 m), a four percent

(4%) reduction of the burner B.T.U. rating shown on the model/

serial plate is required for each 1,000 foot (305 m) increase in

elevation. For assistance when converting to other gas types

and/or installing above 10,000 feet (3048 m) elevation, contact

your local service company.

Stacked Washer/Gas Dryer Gas Supply

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

11

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room,

or recessed area. See “Drain System.”

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the washer/dryer where

it will be exposed to the weather. Do not store or operate the

washer/dryer in temperatures at or below 32°F (0°C). Some

water can remain in the washer and can cause damage in low

temperatures. Proper installation is your responsibility.

You will need:

n A water heater set to deliver 120°F (49°C) water to the

washer.

n A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

n Hot and cold water faucets located within 4 ft. (1.2 m)

of the hot and cold water ll valves, and water pressure

of 20–100 psi (137.9–689.6 kPa).

n A level oor with a maximum slope of 1" (25 mm) under

entire washer/dryer. Installing the washer/dryer on soft oor

surfaces, such as carpets or surfaces with foam backing,

is not recommended.

n A sturdy and solid oor to support the washer/dryer with

a total weight (water and load) of 450 lbs (204 kg).

n A oor drain under the bulkhead. Prefabricated bulkheads

with electrical outlets, water inlet lines, and drain facilities

should be used only where local codes permit.

Stacked Washer/Electric Dryer Location

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

Stacked washer/electric dryer installation clearances

n The location must be large enough to allow the washer and

dryer doors to be fully opened.

n Additional spacing should be considered for ease of

installation and servicing. The doors open more than 180°.

The washer door is not reversible.

n Additional clearances might be required for wall, door, and

oor moldings.

n Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

Recessed Area Installation Instructions

This washer/dryer may be installed in a recessed area. For

recessed area installations, minimum clearances can be found

on the warning label on the rear of the dryer.

The installation spacing is in inches and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes and

ordinances.

The dryer must be exhausted outdoors.

12

n Do not have a fuse in the neutral or ground circuit.

n This washer/dryer is equipped with a power supply cord

having a 3 prong grounding plug.

n To minimize the possibility of shock, the cord must be

plugged into a mating, 3 prong, grounding-type outlet,

grounded in accordance with local codes and ordinances.

If a mating outlet is not available, it is the personal

responsibility and obligation of the customer to have the

properly grounded outlet installed by a qualied electrician.

n If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

n Check with a qualied electrician if you are not sure the

washer is properly grounded.

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

Stacked Washer/Electric Dryer Electrical

Requirements

Stacked Washer/Electric Dryer Grounding

Washer Electrical Requirements

13

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

Dryer Electrical Requirements

It is your responsibility:

n To contact a qualied electrical installer.

n To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996 and dryer circuits

involved in remodeling after 1996.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269.

n To supply the required 3 or 4 wire, single phase, 240 volt, 60

Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specied on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

n Do not use an extension cord.

n If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type

of electrical connection you will be using and follow the

instructions provided for it here.

n This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor

is permanently connected to the neutral conductor (white

wire) within the dryer. If the dryer is installed with a 4-wire

electrical supply connection, the neutral ground conductor

must be removed from the external ground connector (green

screw), and secured under the neutral terminal (center or

white wire) of the terminal block. When the neutral ground

conductor is secured under the neutral terminal (center

or white wire) of the terminal block, the dryer cabinet is

isolated from the neutral conductor.

n If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire

connection” section.

n A 4-wire power supply connection must be

used when the appliance is installed in a location where

grounding through the neutral conductor is prohibited.

Grounding through the neutral is prohibited for (1) new

branch-circuit installations, (2) recreational vehicles, and

(3) areas where local codes prohibit grounding through the

neutral conductor.

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

n A UL listed 30-amp power supply cord, rated 240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U” shaped spade terminals

with upturned ends.

n A UL listed strain relief.

If your outlet looks like this:

4-wire

receptacle

(14-30R)

3-wire

receptacle

(10-30R)

Then choose a 4-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

4-wire power supply cord, at least 4 ft. (1.22 m)

long, must have four 10-gauge copper wires and

match a 4-wire receptacle of NEMA Type 14-30R.

The ground wire (ground conductor) may be either

green or bare. The neutral conductor must be

identied by a white cover.

Then choose a 3-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m)

long, must have three 10-gauge copper wires and

match a 3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

14

Dryer Direct Wire

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

n Flexible armored cable or nonmetallic sheathed copper

cable (with ground wire), covered with exible metallic

conduit. All current-carrying wires must be insulated.

n 10-gauge solid copper wire (do not use aluminum).

n At least 5 ft. (1.52 m) long.

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

15

DRYER VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or exible metal vent shall be used for

exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to

clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may

result in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 7

3

⁄

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not

plugged with lint. Replace plastic or metal foil vents with rigid

metal or exible metal vents. Review “Vent System Chart” and

if necessary, modify existing vent system to achieve best drying

performance.

4"

(102 mm)

4" (102 mm) heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with

screws or other fastening devices that extend into interior

of duct and catch lint. Do not use duct tape.

Better

Good

16

4" (102 mm) Diameter Exhaust Hoods

box hood louvered hood angled hood

Vent Hoods

DRYER VENTING REQUIREMENTS

Exhaust hood must be at least 12" (305 mm) from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of Box and Angled

90˚ Turns Louvered Hood Hood

0 135 ft. (41.2 m) 129 ft. (39.3 m)

1 125 ft. (38.1 m) 119 ft. (36.3 m)

2 115 ft. (35.1 m) 109 ft. (33.2 m)

3 106 ft. (32.3 m) 100 ft. (30.5 m)

4 98 ft. (29.9 m) 92 ft. (28.0 m)

For vent systems not covered by the vent specication chart,

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

“Recessed Area Installation Instructions” in the “Stacked

Washer/Gas Dryer Location” and “Stacked Washer/Electric

Dryer Location” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄

2

"

(64 mm) outlet exhaust hood may be used. A 2

1

⁄

2

" (64 mm)

outlet creates greater back pressure than other hood types.

For permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 mm) clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

12" min.

(305 mm)

Vent collar

17

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

2 ft. (610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1⁄2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

12" min.

(305 mm)*

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 200 CFM of air per dryer.

Large-capacity lint screens of proper design may be used in

main vent if checked and cleaned frequently. The room where

the dryers are located should have make-up air equal to or

greater than CFM of all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from

your distributor and should be installed in the vent of each

dryer to keep exhausted air from returning into dryers and to

keep exhaust in balance within main vent. Unobstructed return

air openings are required.

If an Exhaust Hood Cannot be Used

Multiple Dryer Venting

DRYER VENTING REQUIREMENTS

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

24" min.

(610 mm)

30˚ max.

air ow

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

18

This dryer is equipped for use with natural gas. It is design-

certied by CSA International for LP (propane and butane)

gases with appropriate conversion. No attempt shall be made

to convert dryer from gas specied on serial/rating plate for use

with a different gas without consulting the serving gas supplier.

Conversion must be done by a qualied service technician.

Gas conversion kit part numbers are listed on gas valve burner

base.

Type of Gas

DRYER GAS SUPPLY REQUIREMENTS

Recommended Method

Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to

dryer location. Pipe joint compounds that resist action of LP

gas must be used. Do not use TEFLON

®†

tape. With LP gas,

piping or tubing size can be 1⁄2" (13 mm) minimum. Usually, LP

gas suppliers determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of

the installed shut-off valve to the dryer (as shown above). The

dryer must be disconnected from the gas supply piping system

during any pressure testing of the system at test pressures in

excess of 1/2" psig (352 kg/m

2

).

Alternate Method

The gas supply may also be connected using 3⁄8" (10 mm)

approved copper or aluminum tubing. If the total length of

the supply line is more than 20 ft. (6.1 m), larger tubing will

be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off

valve installed within 6 ft. (1.8 m) of dryer in accordance

with National Fuel Gas Code, ANSI Z223.1. This valve should

be located in same room as dryer. It should be in a location

that allows ease of opening and closing. Do not block access

to shut-off valve. In Canada, an individual manual shut-off

valve must be installed in accordance with the B149 installation

codes CAN/CGA B149.1 and CAN/CGA B149.2.

Gas Supply Line

Flexible Metal Appliance Connector

It is recommended that a new exible stainless steel gas line,

design-certied by CSA International, be used for connecting

the dryer to the gas supply line. (The gas pipe which extends

through the lower rear of the dryer is provided with 3⁄8"

(10 mm) male pipe thread.)

NOTE: Do not kink or damage the exible stainless steel gas

line when moving the door.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe ttings

to obtain an in-line connection to dryer.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

19

4. Models with separate washer power cords: Push the power

cord plug into the opening on the right side of the rear panel

and pull the power cord through the opening on the left side

of the rear panel and close holes with the attached cap. Do

not pull plug end of power cord through the right side hole.

NOTE: To avoid damage to internal washer parts or the

power cord, if the cord does not pull out of the washer rear

panel easily, do not force it. Remove the washer rear panel

and guide the power cord around the obstruction and out

the hole on the left side of the rear panel.

5. Close the bolt holes with the 4 transport bolt hole plugs.

IMPORTANT: If the washer/dryer is to be transported, call

your product distributor or installer. To avoid suspension and

structural damage, your washer/dryer must be properly set up

for relocation by a trained professional.

INSTALLING STACKED WASHER/DRYER

Remove Transport System

NOTE: Slide washer/dryer onto cardboard or hardboard before

moving to avoid damaging oor covering.

IMPORTANT: Position the washer/dryer so that the rear of

the washer is within approximately 3 ft. (900 mm) of its nal

location.

There are 4 shipping bolts in the rear panel of the washer that

support the suspension system during transportation. These

bolts also retain the power cord inside the washer until the

bolts are removed.

1. Keep the washer/dryer in the upright position while removing

the shipping bolts.

2. Using a 1/2" (13 mm) wrench, loosen each of the bolts.

3. Once the bolt is loose, move it to the center of the hole

and completely pull out the bolt, including the plastic spacer

covering the bolt. Once all 4 bolts are removed, discard the

bolts and spacers.

20

INSTALLING STACKED WASHER/DRYER

Connect Inlet Hoses

Insert new hose washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

Connect Inlet Hoses to Water Faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

2. Attach a hose to the cold water faucet. Screw on coupling

by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

Clear Water Lines

n Run water through both faucets and inlet hoses, into a

laundry tub, drainpipe, or bucket, to get rid of particles

in the water lines that might clog the inlet valve screens.

n Check the temperature of the water to make sure that the

hot water hose is connected to the hot water faucet and that

the cold water hose is connected to the cold water faucet.

coupling

washer

Connect Inlet Hoses to Washer

1. Attach the cold water hose to the washer’s cold water inlet

valve. Screw on coupling by hand until it is seated on the

washer.

2. Attach the hot water hose to the washer’s hot water inlet

valve. Screw on coupling by hand until it is seated on the

washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the valve can result.

4. Turn on the water faucets completely and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

La page charge ...

Maytag Commercial MLE20PDCYW Guide d'installation

Maytag Commercial MLE20PDCYW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents