HOTPOINT/ARISTON TCF 87B 6HY/N (EU) Mode d'emploi

Contents

TUMBLE DRYER

TCF 87B

Instruction booklet

GB

English, 1

E

Español, 52

P

Português, 69

D

Deutsch, 35

GB

1

! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and

should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the

dryer so that the new owner may be informed about warnings and suggestions on how the appliance works.

! Read these instructions carefully; the following pages contain important information on installation and suggestions

on how the appliance works.

This symbol reminds you to read this booklet.

F

Français, 18

Important information, 2-3

Product data, 3

Installation, 4

Where to put your dryer

Ventilation

Water drain

Electrical connection

Before you start using your dryer

Dryer description, 5

The features

Control panel

The Display, 6

Start and programmes, 7-11

Choosing a programme

Programmes and Tables

The controls

Laundry, 12-13

Sorting your laundry

Wash care labels

Special clothing items

Drying times

Warnings and Suggestions, 14

General safety

Saving energy and respecting the environment

Maintenance and Care, 15

Switching off the electricity

Cleaning the filter after each cycle

Check the drum after each cycle

Empty the water container after each cycle

Cleaning the condenser unit

Cleaning the dryer

Troubleshooting, 16

Service, 17

Disposal

Important Information

2

GB

! You MUST clean the fluff filter after EVERY drying

cycle.

Fluff Filter...

! Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine.

- It will take longer to dry and as a result will use more electricity during drying.

! You MUST empty the water container after EVERY

drying cycle.

Water Container...

Priming the Water Collection System

When your dryer is new, the water container will not collect water until the system is primed... this will take 1 or 2 drying

cycles. Once primed it will collect water during every drying cycle.

STEP 1.

Open the door of your

dryer.

STEP 2.

Remove the filter.

STEP 3.

Open the filter and clean

any fluff deposits from

the filter mesh.

STEP 4.

Refit the filter - NEVER

run the dryer without the

filter in position.

For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below:

STEP 1.

Pull the water container

towards you and remove

it fully from the dryer.

STEP 2.

Remove either the small or

large cap and empty the

water from the container.

STEP 3.

Refit the water container,

ensuring that it is pushed

fully back into position.

! The ‘Empty Water’

icon reminds you to

empty the water

container at the start and

end of each programme.

! Failure to empty the water container will result in:

- The machine will stop heating (so the load may still be wet at the end of the drying cycle).

- When the water container is full, the ‘Empty Water’ icon will be on, the display will show ‘H20’ and the ‘water

container full’ icon will flash.

GB

3

Important Information

Condenser Unit...

! You MUST clean the fluff from the condenser EVERY

month.

! Failure to clean the condenser could cause premature

failure of your dryer.

●

Check that:

- The positioning arrows are pointing upwards.

- The 3 clips are re-secured back into their ‘lock’ position.

STEP 3.

Flush the condenser, from

the rear with water, to

remove any fluff deposits.

STEP 4.

Refit the condenser unit

- ensure that the unit is

pushed in fully, all 3 clips

are re-secured and the

positiong arrows on the

front of the condenser are

pointing upwards.

Rotate 3 clips

STEP 1.

Open the condenser cover

- hold the handle and

pull towards you.

STEP 2.

Remove the condenser by

rotating the 3 clips then

pulling the condenser

towards you.

(There may be some water

in the tubes, this is normal).

Product Data... (EU Regulation 392/2012)

Rated capacity of Cotton laundry for the standard programme at full load 8 kg Energy efficiency class B

The weighted Annual Energy Consumption (AE

c

) 559.8 kWh

Consumption per year, based on 160 drying cycles of the standard cotton programme at full and partial load, and the

consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used.

This household tumble dryer is an Automatic Condenser Dryer

Energy consumption : full load E

dry

4.70 kWh, partial load E

dry1/2

2.59 kWh

Power consumption : off-mode (P

o

) 0.14 W, left-on mode (P

l

) 2.77 W

Duration of the ‘left-on mode’ for power management systems 30 minutes

The ‘standard cotton programme’ suitable for drying normal wet cotton laundry that is the most efficient programme in

terms of energy consumption for cotton used at full and partial load is Cottons - Cupboard Dry.

Programme time (minutes) : weighted (T

t

) full & partial load 95, full load (T

dry

) 127, partial load (T

dry1/2

) 71

Condensation efficiency class B

Average condensation efficiency (%) : full load (C

dry

) 84, partial load (C

dry1/2

) 78, weighted (C

t

) full & partial load 81

Airborne acoustical noise emissions 69 dB(A) re 1 pW

This data is also available on the website

http://www.hotpoint.eu/hotpoint/

4

GB

Installation

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects

on or above the machine and

a 15mm space between the

sides and lateral furnishings

or walls.

This is to ensure proper air circulation.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. If the dryer is stacked onto or

installed next to a washing machine it can share the same

drain. The height of the drain must be less than 3' (1m)

from the bottom of the dryer.

Remove hose from position shown

(see diagram).

Fit a suitable length of hose to the

new location shown (see diagram).

! Make sure that the hose is not squashed or kinked when

the dryer is in its final location.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the

socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see Service).

New or longer power cords are supplied at an extra

charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a

qualified electrician.

Minimum gap 10mm

Minimum gaps

15mm

Remove hose from

here...

...fit new hose here.

GB

5

Dryer Description

Control panel

PROGRAMME

knob

Display Unit &

Selection Buttons

START/PAUSE

Button & Light

CHILD LOCK

Button & Light

HEAT LEVEL

Button & Lights

ON/OFF

Button

Indicator

The ON/OFF button : If the dryer is running and this

button is pressed and held for more that 3 seconds the dryer

is turned off, it counts down 3, 2, 1, Off and the programme

is then cancelled.

Press and hold for more than 3 seconds and the dryer

reactivates.

The PROGRAMMES knob sets the programme: rotate it until

the indicator is pointing to the programme you want to select

(see Start and Programmes).

The OPTION buttons select available options for your

selected programme. The lights indicate that the option has

been selected (see Start and Programmes).

The START/PAUSE button/light starts a selected

programme. When you press this button there will be one

beep and the progress lights will flash to confirm the action.

When a programme is running, holding this button in pauses

the programme and stops the dryer.

The light is green when programme is running, flashing amber

if the programme has been paused or flashing green if on

standby waiting to start a programme (see Start and

Programmes).

The Display Unit gives an indication of the drying or delay

time together with icons that light to give warning information

and show the status of your programmes progress.

The three buttons below the display select ‘Automatic’ or

‘Timed Dry’ and if required a delayed start (see Start and

Programmes or The Display).

The CHILD LOCK button/light : Press and hold this

button after selecting your programme and any options, the

light turns on. This prevents the programme settings from

being changed. When the light is lit, the other buttons are

disabled. Hold the button to cancel and the light will go out.

The Empty Water icon : signals that the water container

should be emptied. The display will take a few seconds to

update after replacing the empty water container, the dryer

must be running for this to happen (see The Controls).

Note: If the water container fills the ‘water container full ‘icon

flashes, the display shows , the heat is turned off and

your clothes will not dry.

The Clean Filter icon : gives a reminder before every

programme, that it is essential to clean the filter every time

the dryer is used (see Maintenance and Care).

The Clean Condenser icon : gives a reminder that it is

essential to clean the condenser at regular intervals (see

Maintenance and Care).

The features

Water container

Filter

Condenser cover

Rating plate

Model & Serial numbers

Condenser cover handle

(Pull to open)

Air intake grille

OPTION

Buttons & Lights

6

GB

The Display

The Display has three main functions, each with its corresponding button.

After selecting a programme that has a Sensor Dry option, press and release the button until the required

dryness sensing level is displayed. If the sensing option is not available with your selected programme, the

display will flash and the buzzer will beep three times.

! Some sensing programmes do not have all seven dryness level options available.

Dryness levels:

Damp Dry: Dries your items ready to be ironed using a machine or rotary ironer.

Iron Dry: Dries your items ready to be ironed with a hand iron.

Hanger Dry Plus: Dries your delicate items ready to be hanged for final drying.

Hanger Dry: Dries your items ready to be hanged for final drying.

Light Dry: Dries your delicate items ready to be put away.

Cupboard Dry: Dries your items ready to be put away.

Extra Dry: Dries your items ready to be worn.

Timed Dry

Dryness Sensing Levels

Delay Timer

24h

OFF

9.59

After selecting a programme that has a Delay Timer option, a delay start time can be selected.

Each press of the Delay Timer button advances the delay setting in 30 minutes increments from

to and then increments from to then and then after five seconds cancels the

delay.

For delays of 10 hours or more the display counts down the time in hours until 10 hours, then the

display shows and then continues to count down in minutes.

For delays 9 hours or less the display shows hours and minutes and then counts down in minutes for

all of the delay.

After the START/PAUSE button is pressed the delay time can be changed or cancelled.

When the delay period finishes the delay icon is off and the Time to End is displayed.

Note: During this period the clothes will tumble occasionally to prevent creases developing.

0:30

9:30

Time to End

If the delay icon is off the time displayed is the Time to End for the programme running.

When timed programmes are selected the time displayed throughout the cycle is the actual time remaining.

When Automatic programmes are selected the time displayed is an estimate of the time remaining: When the

programme is selected the display shows the time required to dry a full load. The time remaining is constantly

monitored during the drying cycle and is updated to show the best forecast.

The Time to End is displayed in hours and minutes and counts down each minute.

The colons between the hours and minutes in the display flash to show the time is counting down.

The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault

code number, the three option lights and the START/PAUSE light will also flash amber (see Troubleshooting).

After selecting a programme that has a Timed Dry option, press the button and the Timed Dry icon will

light, the display will reduce the selected time each time you press and release this button (see Start and

Programmes). Each programme that has a timed option has different times available and the selection of

up to 11 drying times will also depend on the heat setting that your have selected.

Each press of the button decreases the drying time.

If you change your mind, press the Sensor Dry button and the sensing level options are available.

If the Timed Dry option is not available the display will flash and the buzzer will beep three times.

The selected time remains displayed after the programme starts and can be changed during the

programme if you wish.

10h

GB

7

Start and Programmes

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place and the water container is empty and

in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If none of the lights are on: Press the ON/OFF

button .

6. Choose a programme by checking the Programmes

Guide (see Programmes) as well as the indications

for each type of fabric (see Laundry).

- Select a programme by rotating the

PROGRAMMES knob.

7. Choose Timed Drying or Dryness Levels option:

- If Timed Dry press and release the Timed

button until the required time is displayed.

or - To change from default dryness setting, press

and release the Sensor Dry button until the

required level is indicated (see The Display).

! For full details of selections available for each

programme see the Programme Tables.

Cottons

●

This is a programme for cotton items.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

Note: This tumble dryer, in compliance with new energy saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no activity is detected.. Press and hold the ON/OFF button until

the dryer reactivates.

8. Set a delay time and other options if necessary.

9. The START/PAUSE light is flashing green:

- press the START/PAUSE button to begin.

The green light stops flashing.

During the drying programme, you can check on

your laundry and take out items that are dry

while others continue drying. When you close

the door again, press the START/PAUSE button in

order to resume drying.

(When the door is opened the START/PAUSE light

will flash Amber, after the door is closed and the

START/PAUSE button pressed, the START/PAUSE

light will stop flashing and show green.)

10. To let you know that your programme is complete

the buzzer will beep 3 times.

Open the door, take the laundry out, clean the filter

and replace it. Empty the water container and

replace it (see Maintenance).

11. Unplug the dryer.

Programme Options available

1 Cottons

4 Anti Allergy

6 Quick Dry

5 Synthetics

3 Bed & Bath

ESSENTIAL PROGRAMMES - Programmes Table

2

Shirts

✗

✓

✗

✗ ✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

Dryness Levels available

(default highlighted )

Delay Timer

Ready to Iron

Less tangled

Heat Level

Timed Dry

Sensor Dry

●

An Automatic programme

●

An Automatic programme

- Medium

- Low

- High

- Medium

- Low

- High

- Medium

- High

- Medium

- High

Damp Dry

Iron Dry

Hanger Dry Plus

Hanger Dry

Light Dry

Cupboard Dry

Extra Dry

✗

✓

✗

✓

8

GB

Start and Programmes

Bed & Bath

●

This is a programme for cotton towels and sheets.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

●

Loads dried using the Extra Dry setting are usually ready to use, the edges or seams may be slightly damp

especially on large items. If this is the case, try opening them out and running the programme again for a short

period.

Programme Options available

7 Jeans

10 Baby cycle

12 Duvet

11 Delicates

9 Silk

EXCLUSIVE PROGRAMMES - Programmes Table

8

Wool

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

✗

✓

Dryness Levels available

(default highlighted )

Delay Timer

Ready to Iron

Less tangled

Heat Level

Timed Dry

Sensor Dry

●

An Automatic programme

●

An Automatic programme

Damp Dry

Iron Dry

Hanger Dry Plus

Hanger Dry

Light Dry

Cupboard Dry

Extra Dry

Shirts

High heat option

●

This is a programme for shirts made from cotton.

●

It can be used for load sizes up to 3kg (approximately 10 shirts).

Medium heat option

●

This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such

as polyester and cotton.

●

It can be used for load sizes up to 3kg (approximately 14 shirts).

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer.

Loads dried using the Cupboard Dry setting are usually ready to wear, the edges or seams may be slightly damp. If

this is the case, try turning the shirts inside out and running the programme again for a short period.

Synthetics

●

This is a programme for items of Synthetic or Synthetic/Cotton mixtures.

●

The duration of this programme will depend on the size of the load, the dryness setting selected and the spin

speed used in your washer (see Laundry).

Anti Allergy Programme

This programme has the ‘Seal of Approval’ endorsement from Allergy UK, which reflects the effective reduction and

elimination of allergens from the clothes with the special Anti Allergy cycle. With this programme, thanks to the

achievement of constant temperature for an extended period of time, the effects of the most common allergens

(including House Mites and Pollen) are neutralised.

Can be used on a full size wet load to dry and treat, or on a 4kg dry load just to treat your laundry.

Quick Dry

This programme is for small loads maximum 1kg. Note: can only be used with the Cupboard Dry setting.

Your drying time is very much reduced with a huge time saving up to 53% on cottons (with High Heat option) and

50% on synthetics (with Medium Heat option).

- High

- Medium

GB

9

Start and Programmes

Wool Programme

●

This is a programme for tumble dryer safe garments marked with the symbol .

●

It can be used for load sizes up to 1kg (approximately 3 sweaters).

●

We recommend that garments are turned inside out before drying.

●

The duration of this programme will depend on the size and density of the load and the spin speed used in your

washer.

●

Loads dried using this programme are usually ready to wear, but on some heavier garments the edges may be

slightly damp. Allow these to dry naturally as over-drying could damage garments.

! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to original size and

shape.

! This programme is not suitable for Acrylic garments.

Baby cycle

●

This is a programme for drying your baby’s small delicate items of clothing and bedding (Cotton and Chenille)

and for drying your delicate clothes.

●

DO NOT dry items such as bibs and nappy pants with plastic coverings.

●

It can be used for load sizes up to 2kg.

●

The duration of this programme will depend on the size and density of the load and the spin speed used in your

washer.

●

Loads dried using this programme are usually ready to use, but on some garments the edges may be slightly

damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short

period.

Duvet

! Take care with this programme DO NOT dry any items that are damaged which could result in the filling blocking

the filter and air vent resulting in a fire hazard.

●

Must only be used on single size duvets: NOT suitable for double or king size items.

●

Loads dried using this programme are usually ready to use, but may be slightly damp in places. If this is the case,

try opening them out and shaking them and running the programme again for a short period.

●

Also suitable for down filled jackets.

●

Select high heat for Cotton Duvets and medium heat for Synthetic duvets

●

The duration of this programme will depend on the size and density of the load and the spin speed used in your

washer.

Delicates

●

This is a programme for drying your delicate clothes ie. Acrylics.

●

It can be used for load sizes up to 2kg.

●

The duration of this programme will depend on the size and density of the load and the spin speed used in your

washer.

●

Loads dried using this programme are usually ready to use, but on some garments the edges may be slightly

damp. If this is the case, try opening them out or turn items inside out and running the programme again for a short

period.

Silk

●

This is a programme for drying your delicate silk.

●

It can be used for load sizes up to 0.5kg.

●

The duration of this programme will depend on the size and density of the load and the spin speed used in your

washer.

●

Loads dried using this programme are usually ready to use, but on some heavier garments the edges may be

slightly damp. If this is the case, remove the load and open them out and then run the programme again for a short

period.

Jeans

●

This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out.

●

It can be used for load sizes up to 3kg (approximately 4 pairs).

●

Do not mix dark and light coloured items.

●

It can also be used on other garments made from the same material, such as jackets.

●

The duration of this programme will depend on the size of the load and the spin speed used in your washer.

●

Loads dried using this programme are usually ready to wear, the edges or seams may be slightly damp. If this is

the case, try turning the jeans inside out and running the programme again for a short period.

! We do not recommend that you use this programme if your jeans have elastic waist bands, studs or embroidery.

10

GB

Start and Programmes

Cuddly Toy Programme

With this programme you can remove dust easier and wash the cuddly toys more often because the drying time is

very much reduced compared to drying in the open air. It is a delicate drying cycle that dries at low temperature

and with soft mechanical action to maintain at best the original look and shine of the fur.

Note: For allergy protection, just freeze cuddly toys for 24 hours then wash and dry them. Repeat every 6 weeks.

Before drying remove accessories such as clothes, collars or sound boxes and protect plastic eyes with masking

tape after drying them with a cloth.

The programme time will vary dependant on the exact make up of the load.

The maximum load should not exceed 2.5kg and no individual item should be greater than 600g.

Refresh

! ‘Refresh’ is not a drying programme and should not be used for wet articles of clothing.

●

It can be used on any load size but is more effective on smaller loads.

●

Do not overload your dryer (see Laundry).

●

This is a 20 minute programme that airs your clothes with cool air. Also use to cool warm clothes.

16 Refresh

15 Pre Iron

Programme Options available

EXTRA PROGRAMMES - Programmes Table

✗

✓

Dryness Levels available

(default highlighted )

Delay Timer

Ready to Iron

Less Tangled

Heat Level

Timed Dry

Sensor Dry

●

An Automatic programme

●

An Automatic programme

●

An Automatic programme

●

An Automatic programme

14 Heat & Enjoy

Damp Dry

Iron Dry

Hanger Dry Plus

Hanger Dry

Light Dry

Cupboard Dry

Extra Dry

13 Cuddly Toys

Heat & Enjoy

This programme helps to heat towels & bathrobes for a warm sensation after a bath or shower. It is also useful for

warming clothes before dressing during winter. The cycle heats clothes to 37°C (Body Temperature) and runs at this

temperature for a maximum of 4 hours or until you stop the cycle by opening the door.

Maximum load 3kg.

Note: During this programme a icon rotates in the display until the target temperature is reached, at which point

the icon flashes.

Pre Iron Programme

‘Pre Iron’ is a treatment cycle for use with dry clothes and reduces creases in order to facilitate ironing and folding,

it has a maximum duration of 15 minutes.

! ‘Pre Iron’ is not a drying programme and should not be used for wet articles of clothing.

For best results: 1. Do not load more than the maximum capacity.

These numbers refer to the dry weight:

Fabric Maximum load

Cotton and Cotton mixtures 2.5kg

Denim 2kg

2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles

and put them away in the closet. Should this not be possible repeat the programme.

GB

11

Start and Programmes

●

Programmes knob

! Warning, if after pressing the START/PAUSE button

the programme knob position has changed, the new

position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button , the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will then

flash green. Press the START/PAUSE button again

and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. A programme must

have been selected on the programme knob before an

option can be selected. Not all options are available for all

programmes (see Start and Programmes). If an option is

not available and you press the button, the buzzer will

beep three times. If the option is available the option light

in the button lights to confirm the selection.

Progress ( Drying, Cool Tumble) icons

These are part of the Display, they indicate the progress

of the dryer. Each icon comes on as the corresponding

phase starts.

Time Delay (Delay Timer)

The start of some programmes (see Start and

Programmes) can be delayed for up to 24 hours. Ensure

the water container is emptied before setting a delayed

start. During this period the clothes are occasionally

tumbled to help prevent creases developing.

Ready to Iron

This option allows you to dry loads where only some

of the items need ironing and you do not wish to fully

dry those items.

When Iron Dry level is reached, a buzzer sounds to let

you know that the items that need ironing can be

removed. The dryer then stops and the Start/Pause

light flashes orange. Remove the items you wish to

iron, close the door and press the Start/Pause button,

the dryer continues until the remaining items reach the

selected dryness level.

It can be used on load sizes up to 3kg.

Note: This option is not available with the ‘Iron Dry’ and

‘Damp Dry’ dryness levels.

Less Tangled

This option has the drum movement modified to give a

tumbling action that reduces tangling and knotting of your

clothes.

The Less Tangled option gives best results when used

with smaller loads.

Heat Level buttons and lights

Not all programmes allow you to change the heat level

and some programmes allow all three heat level options:

Low, Medium and High.

When the heat level options are available pressing this

button changes the heat level and the light corresponding

to the selection is lit.

The Controls

8:88

●

DISPLAY

The display shows either the amount of time delay

remaining or an indication of the amount of time left for a

drying programme (see The Display).

The colons between the hours and minutes in the display

flash to show that the time is counting down.

When the programme finishes its cool tumble phase the

display will show ‘End’.

●

Empty Water Icon / Container

(If you have plumbed your dryer to a drain this icon can

be ignored, as there is no need to empty the water

container).

When this icon is on ( ) it reminds you to empty the

water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the buzzer sounds, the ‘water container

full’ icon flashes, the display shows and the

‘empty water’ icon is on.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer the display will take a few seconds to refresh.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door (or pressing the Start/Pause button)

during a programme will stop the dryer and have the

following effects:

●

The START/PAUSE light flashes Amber.

●

During a delay phase the delay will continue to

count down. The START/PAUSE button must be

pressed to resume the delay programme.

●

The START/PAUSE button must be pressed to

resume programme. The progress lights will change

to show the current status and the Start/Pause light

will stop flashing and turn green.

●

Changing the programmes knob will select a new

programme and the START/PAUSE light will flash

green. You can use this to select the Refresh

programme to cool the clothes, if you find them

dry enough. Press the START/PAUSE button to

begin a new programme.

●

Note

If you have a power cut, switch off the power or remove

the plug. When power is restored, press and hold the

ON/OFF button until the dryer reactivates, then press the

Start/Pause button.

12

GB

Laundry

Sorting your laundry

●

Check symbols on clothing labels to make sure

that the articles can be tumble dried.

●

Sort laundry by fabric type.

●

Empty pockets and check buttons.

●

Close zippers and hooks and tie loose belts and

strings.

●

Wring out each item in order to eliminate as much

excess water as possible.

! Do not load dripping wet clothes into the dryer.

Maximum load size

Do not load more than maximum capacity.

These numbers refer to dry weight:

Natural fibres: 8kg max (18lb)

Synthetic fibres: 3kg max (6.6lb)

! DO NOT overload the dryer as this could result in

reduced drying performance.

Typical weights

Note: 1kg = 1000g (1lb = 16oz)

Clothes

Blouse Cotton 150g (5oz)

Other 100g (3oz)

Dress Cotton 500g (1lb 2oz)

Other 350g (12oz)

Jeans 700g (1lb 6oz)

10 nappies 1000g (2lb 3oz)

Shirt Cotton 300g (10oz)

Other 200g (7oz)

T-Shirt 125g (4oz)

Household Items

Duvet cover Cotton 1500g (3lb 5oz)

(Double) Other 1000g (2lb 3oz)

Large Tablecloth 700g (1lb 6oz)

Small Tablecloth 250g (9oz)

Tea Towel 100g (3oz)

Bath Towel 700g (1lb 6oz)

Hand Towel 350g (12oz)

Double Sheet 500g (1lb 2oz)

Single Sheet 350g (12oz)

At the end of a drying cycle, cottons could still be

damp if you grouped cottons and synthetics together.

If this happens simply give them an additional short

period of drying.

Wash Care Labels

Look at the labels on your garments, especially when

tumble drying for the first time. The following symbols

are the most common:

May be tumble dried

Do not tumble dry

Tumble dry at high heat setting

Tumble dry at low heat setting

Items not suitable for tumble drying

●

Articles that containing rubber or rubber-like

materials or plastic film (pillows, cushions, or PVC

rainwear), any other flammable articles or objects

that contain flammable substances (towels soiled

with hair spray).

●

Glass fibres (certain types of draperies)

●

Items which have been dry cleaned

●

Items with the ITCL Code (see Special

clothing items). These can be cleaned with special

at-home dry cleaning products. Follow instructions

carefully.

●

Large bulky items (quilts, sleeping bags, pillows,

cushions, large bedspreads etc). These expand

when drying and would prevent airflow through

the dryer.

GB

13

Laundry

Special clothing items

Blankets and Bedspreads: acrylic items (Acilan,

Courtelle, Orion, Dralon) must be dried with special

care on LOW heat setting. Avoid drying for a long

period of time.

Pleated or creased garments: read the manufacturer’s

drying instructions on the garment.

Starched articles: do not dry these with non-starched

items. Make sure that as much of the starch solution is

removed from the load as possible before placing it in

the dryer. Do not over-dry: the starch will become

powdery and leave your clothing limp, which defeats

the purpose of starch.

Drying times

The table (see below) presents APPROXIMATE drying

times in Minutes. Weights refer to dry garments.

Times are approximate and can vary depending

upon:

●

Amount of water retained in clothes after spin

cycle: towels and delicates retain a lot of water.

●

Fabrics: items that are the same type of fabric but

different textures and thicknesses may not have

the same drying time.

●

Quantity of laundry: single items or small loads

may take longer to dry.

●

Dryness: If you are going to iron some of your

clothes, they can be taken out while still a bit

damp. Others can be left longer if you need them

to be completely dry.

●

Heat setting.

●

Room temperature: if the room where the dryer is

located is cold, it will take longer for the dryer to

dry your clothes.

●

Bulk: some bulky items can be tumble dried with

care. We suggest that you remove these items

several times, shake them out, and return them to

the dryer until finished.

! Do not over-dry your clothes.

All fabrics contain a little natural moisture, which

keeps them soft and fluffy.

Cottons

High/Full

Heat

Synthetics

Gentle/Low

Heat

Acrylics

Gentle/Low

Heat

Drying times 800-1000 rpm in washing machine.

Drying times on reduced spin in washing machine.

1 kg

2 kg

4 kg

3 kg

1 kg

2 kg

1 kg

2 kg

3 kg

5 kg

6 kg

7 kg

30 - 40

40 - 55

70 - 80

55 - 70

80 - 90

95 - 120

120 - 140

40 - 50

40 - 60 55 - 75

50 - 70

70 - 90

8 kg

130 - 150

14

GB

Warnings and Suggestions

! The appliance has been designed and built according

to international safety standards.

These warnings are given for safety reasons and must

be followed carefully.

General safety

●

This tumble dryer is not intended for use by

persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

●

This tumble dryer has been designed for home,

and not professional use.

●

Do not touch the appliance while barefoot or with

wet hands or feet.

●

Unplug the machine by pulling on the plug, not

the cord.

●

Children must not be in proximity of the dryer

when in use. After using the dryer, turn it off and

unplug it. Keep the door closed to make sure that

children do not use it as a toy.

●

Children should be supervised to ensure that they

do not play with the dryer.

●

The appliance must be installed correctly and

have proper ventilation. The air intake at the front

of the dryer should never be obstructed (see

Installation).

●

Never use the dryer on carpeting where the pile

height would prevent air from entering the dryer

from the base.

●

Check to see if the dryer is empty before loading it.

●

The back of the dryer could become very

hot. Never touch it while in use.

●

Do not use the dryer unless the filter, water

container and condenser are securely in place

(see Maintenance).

●

Do not overload the dryer (see Laundry for

maximum loads).

●

Do not load items that are dripping wet.

●

Carefully check all instructions on clothing labels

(see Laundry).

●

Do not tumble dry large, very bulky items.

●

Do not tumble dry acrylic fibres at high temperatures.

●

Complete each programme with its Cool Tumble Phase.

●

Do not turn off the dryer when there are still warm

items inside.

●

Clean the filter after each use (see Maintenance).

●

Empty the water container after each use (see

Maintenance).

●

Clean the condenser unit at regular intervals

(see Maintenance).

●

Do not allow lint to collect around the dryer.

●

Never climb on top of the dryer. It could result in damage.

●

Always follow electrical standards and requirements

(see Installation).

●

Always buy original spare parts and accessories

(see Service).

To minimise the risk of fire in your tumble dryer, the

following should be observed:

●

Tumble dry items only if they have been washed with

detergent and water, rinsed and been through the spin

cycle. It is a fire hazard to dry items that HAVE NOT

been washed with water.

●

Do not dry garments that have been treated with

chemical products.

●

Do not tumble dry items that have been spotted or

soaked with vegetable or cooking oils, this constitutes a

fire hazard. Oil-affected items can ignite spontaneously,

especially when exposed to heat sources such as a tumble

dryer. The items become warm, causing an oxidisation

reaction with the oil, Oxidisation creates heat. If the heat

cannot escape, items can become hot enough to catch

fire. Piling, stacking or storing oil-effected items can prevent

heat from escaping and so create a fire hazard.

If it is unavoidable that fabrics containing vegetable or

cooking oil or those that have been contaminated with

hair care products be placed in a tumble dryer they should

first be washed with extra detergent - this will reduce, but

not eliminate the hazard. The cool tumble phase should

be used to reduce the temperature of the items. They

should not be removed from the dryer and piled or

stacked while hot.

●

Do not tumble dry items that have previously been

cleaned in or washed in, soaked in or soiled with

petrol/gasoline, dry cleaning solvents or other flammable

or explosive substances. Highly flammable substances

commonly used in domestic environments including

cooking oil, acetone, denatured alcohol, kerosene, spot

removers, turpentine, waxes and wax removers. Ensure

these items have been washed in hot water with an extra

amount of detergent before being dried in the tumble dryer.

●

Do not tumble dry items containing foam rubber (also

known as latex foam), or similarly textured rubber like

materials. Foam rubber materials can, when heated,

produce fire by spontaneous combustion.

●

Fabric softener or similar products should not be used in

a tumble dryer to eliminate the effects of static electricity

unless the practice is specifically recommended by the

manufacturer of the fabric softener product.

●

Do not tumble dry undergarments that contain metal

reinforcements eg. bras with metal reinforcing wires.

Damage to the tumble dryer can result if the metal

reinforcements come loose during drying.

●

Do not tumble dry rubber, plastic articles such as shower

caps or babies waterproof covers, polythene or paper.

●

Do not tumble dry rubber backed articles, clothes fitted

with foam rubber pads, pillows, galoshes and rubber

coated tennis shoes.

●

Remove all objects from pockets, especially lighters

(risk of explosion).

! WARNING: Never stop the dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

Saving energy and respecting the environment

●

Wring out items to eliminate excess water before

tumble drying (if you use a washing machine first,

select a high spin cycle). Doing this will save time

and energy during drying.

●

Always dry full loads - you save energy: single

items or small loads take longer to dry.

●

Clean the filter after each use to contain energy

consumption costs (see Maintenance).

GB

15

Maintenance and Care

Cleaning the drum

! Do not use abrasives, steel wool or stainless steel

cleaning agents to clean the drum.

A coloured film may start to appear on the stainless

steel drum, this may be caused by a combination of

water and, or cleaning agents such as fabric conditioner

from the wash. This coloured film will not affect the

dryer performance.

Cleaning the condenser unit

Periodically (every month) remove the condenser unit

and clean any build up of fluff from between the plates

by rinsing it under the tap with cold water.

This should be done with cold water from the rear of

the condenser.

Removing the condenser:

1. Unplug the dryer and open the door.

2. Pull open the condenser cover (see diagram).

Release the three catches by turning 90˚ counter-

clockwise then pull on the grip and remove from

the dryer.

3. Clean the surface of the seals and replace, making

sure that the catches have been secured.

Cleaning the dryer

●

External parts in metal or plastic and rubber parts

can be cleaned with a damp cloth.

●

Periodically (every 6 months) vacuum the front air

intake grille, to remove any build up of fluff, lint or

dust. Also to remove accumulation of fluff from the

front of the condenser and filter areas, clean

occasionally with a vacuum cleaner.

! Do not use solvents or abrasives.

! Your dryer uses special bearing components which

do not need lubrication.

! Have your dryer checked regularly by authorised

technicians to ensure electrical and mechanical safety

(see Service).

Switching off the electricity

! Unplug your dryer when not using it, when cleaning

it and during all maintenance operations.

Clean the filter after each cycle

The filter is an important part of your dryer:

it accumulates lint and fluff that is formed while drying.

When finished drying, clean the filter by rinsing it

under running water or with your vacuum cleaner.

Should the filter become clogged up, the airflow inside

the dryer will be seriously compromised: drying times

lengthen and you will consume more energy. It may

also damage your dryer.

The filter is found in front of the dryer trim (see diagram).

Removing the filter:

1. Pull the plastic grip of the filter upwards (see diagram).

2. Open the filter and clean the lint from

the inside.

3. Replace it correctly. Ensure the filter

is fully located flush into the tumble

dryer trim.

4. Remove any lint that has built up on the inside of the

door and around the door seal.

! Do not use the dryer without replacing the filter.

Check the drum after each cycle

Turn the drum manually in order to remove small items

(handkerchiefs) that could have been left behind.

Empty the water container after each

cycle

Pull the container out of the dryer and remove either

the small or large cap and empty it into a sink or other

suitable drain. Refit the cap and replace the container

securely.

! Always check and empty the container before you

start a new drying programme.

Water container

Condenser cover

Catches

Air intake

Filter

Tap

Rear

Front

Condenser unit

16

GB

Troubleshooting

Problem:

The tumble dryer won’t start.

Drying cycle will not begin.

Its taking a long time to dry.

The ‘water container full’ icon

is flashing and displayed

but the dryer has only been

running for a short period.

Empty water icon is on and

the water container is not full.

Programme finishes and

clothes are damper than

expected.

The display shows a fault

code F followed by one or two

numbers

Possible causes / Solution:

●

The plug is not plugged into the socket, or not making contact.

●

There has been a power failure.

●

The fuse has blown. Try to plug another appliance into the socket.

●

You are using an extension cord? Try to plug the dryer’s power cord

directly into the socket.

●

The door is not closed securely?

●

The PROGRAMMES knob has not been set properly (see Start and

Programmes).

●

The START/PAUSE button has not been pressed (see Start and Programmes).

●

You have set a delayed time (see Start and Programmes).

●

The filter has not been cleaned (see Maintenance).

●

The water container needs emptying... The ‘water container full’ icon

is flashing, the display shows and the ‘empty water’ icon is on

(see Maintenance).

●

The condenser needs cleaning? (see Maintenance).

●

The temperature setting is not ideal for the type of fabric you are drying

(see Start and Programmes, and see Laundry).

●

The correct drying time has not been selected for the load (see Laundry).

●

The air intake grille is obstructed (see Installation, and see

Maintenance).

●

The items were too wet (see Laundry).

●

The dryer was overloaded (see Laundry).

●

The water container was probably not emptied at the start of the

programme. Do not wait for the empty water signal, always check and

empty the container before starting a new drying programme (see

Maintenance).

●

This is normal. If the icon is on it is just a reminder to empty the container

(see Start and Programmes).

! For safety the dryer has a maximum programme time of 5 hours. If an

automatic programme has not sensed the required final moisture in this time

the dryer will complete the programme and stop. Check the above points

and run the programme again, if the results are still damp, contact the

Service Centre (see Service).

●

If the display shows a fault:

- Turn off and remove the plug. Clean the filter and the condenser

unit (see Maintenance). Then replace the plug, turn on and start

another programme. If a fault is then displayed: Note down the

code and contact the Service Centre (see Service).

One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the

following troubleshooting suggestions:

Service

GB

17

Spare Parts

This dryer is a complex machine. Repairing it yourself

or having a non-authorised person try to repair it could

cause harm to one or more persons, could damage

the machine and could invalidate the spare parts

warranty.

Call an authorised technician if you experience problems

while using the machine.

Before calling the Service Centre:

●

Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

●

If not, turn off the dryer and call the Service Centre

closest to you.

What to tell the Service Centre:

●

name, address and post code.

●

telephone number.

●

the type of problem.

●

the date of purchase.

●

the appliance model (Mod.).

●

the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Disposal of old electrical appliances

The European Directive 2012/19/EC on Waste Electrical

and Electronic Equipment (WEEE), requires that old

household electrical appliances must not be disposed

of in the normal unsorted municipal waste stream. Old

appliances must be collected separately in order to

optimise the recovery and recycling of the materials

they contain and reduce the impact on human health

and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct disposal

of their old appliance.

As part of our continued commitment to helping

the environment, we reserve the right to use

quality recycled components to keep down customer

costs and minimise material wastage.

●

Disposing of the packaging material: follow local

regulations, so the packaging can be recycled.

●

To minimise risk of injury to children, remove the

door and plug - then cut off mains cable, flush

with the appliance. Dispose of these parts separately

to ensure that the appliance can no longer be

plugged into a mains socket.

Recycling and Disposal Information

This appliance conforms to the following EC Directives:

- 2006/95/EC (Low Voltage Equipment)

- 2004/108/EC (Electromagnetic Compatibility)

TCF 87B

F

Français, 18

F

SÈCHE-LINGE

Notice d’utilisation et installation

Table des Matières

Informations Importantes, 19-20

Données relatives au produit, 20

Installation, 21

Où installer votre sèche-linge

Ventilation

Vidange de l’eau

Connexions électriques

Avant de commencer à utiliser votre sèche-linge

Description du sèche-linge, 22

Caractéristiques

Panneau de commandes

L’affichage, 23

Démarrage et programmes, 24-28

Choisir un programme

Programmes et tableaux

Les commandes

Linge, 29-30

Trier votre linge

Étiquettes d’entretien

Vêtements spéciaux

Temps de séchage

Avertissements et Suggestions, 31

Sécurité générale

Économiser de l’énergie et respecter l’environnement

Entretien et Nettoyage, 32

Éteindre l’électricité

Nettoyer le filtre après chaque cycle

Videz le réservoir d’eau après chaque cycle

Vérifier le tambour après chaque cycle

Nettoyage du tambour

Nettoyage du groupe condenseur

Nettoyer le sèche-linge

Que faire en cas de panne, 33

Service Après-vente, 34

Mise au rebut

! Conservez cette notice d’utilisation et d’installation à portée de main de manière à pouvoir vous y référer si

nécessaire. Emmenez-la avec vous si vous déménagez, et, si vous vendez cet appareil ou que vous le donniez à un tiers,

faites en sorte que cette notice accompagne le sèche-linge de manière à ce que le nouveau propriétaire soit informé

des avertissements et suggestions concernant le fonctionnement de ce sèche-linge.

! Lisez attentivement ce mode d’emploi; les pages suivantes contiennent des informations importantes concernant

l’installation et des suggestions relatives au fonctionnement de cet appareil.

Ce symbole vous rappele de lire le livret d’instructions.

18

GB

English, 1

E

Español, 52

P

Português, 69

D

Deutsch, 35

F

19

Informations Importantes

! Vous devez IMPERATIVEMENT nettoyer le filtre à

peluches A CHAQUE cycle de séchage.

Filtre...

! Négliger de nettoyer le filtre après CHAQUE cycle de séchage nuira aux performances de séchage de votre

machine.

- Le temps de séchage sera plus long et la consommation électrique sera en conséquence plus importante.

! Vous devez IMPERATIVEMENT vider le réservoir

d’eau après CHAQUE cycle de séchage.

Réservoir d’eau...

Amorçage du système de récupération d’eau

Sur un sèche-linge neuf, le réservoir d’eau ne récupérera pas l’eau tant que le système n’aura pas été amorcé...

ceci nécessitera 1 ou 2 cycles de séchage. Une fois amorcé, il récupérera l’eau à chaque cycle de séchage.

ETAPE 1.

Ouvrez la porte du

sèche-linge.

ETAPE 2.

Sortez le filtre.

Pour que votre sèche-linge à condenseur fonctionne efficacement, vous devez suivre le programme d’entretien

courant décrit ci-dessous:

ETAPE 1.

Tirez le réservoir d’eau

vers vous et retirez-le

complètement du sèche-

linge.

ETAPE 2.

Retirez le petit capot ou

le grand capot et videz

l'eau du réservoir.

ETAPE 3.

Ouvrez le filtre et

débarrassez-le des

peluches qui se seraient

déposées dans le maillage.

ETAPE 4.

Réinstallez le filtre - NE

faites JAMAIS fonctionner

le sèche-linge sans avoir

remis en place le filtre.

ETAPE 3.

Remettez en place le

réservoir d’eau, en

veillant à le renfoncer

correctement.

! L'icône "Vider

l'eau" vous rappelle de

vider le réservoir d’eau

au début et à la fin de

chaque programme.

! Si vous négligez de vider le réservoir d’eau :

- la machine ne chauffe plus (la charge est alors encore humide à la fin du cycle).

- Lorsque le réservoir d'eau est plein, l'icône "Vider l'eau" s'allume. L'Affichage indique ‘H20’ et l'icône

"Réservoir d'eau plein" clignote.

F

20

Informations Importantes

Groupe condenseur...

! Vous devez IMPERATIVEMENT enlever les peluches

du condenseur TOUS LES MOIS.

! Négliger de nettoyer le condenseur pourrait entraîner

une défaillance prématurée de votre sèche-linge.

●

Vérifiez:

- que les flèches de positionnement sont orientées vers le haut.

- que les 3 agrafes sont refermées dans leur position de « verrouillage ».

ETAPE 3.

Rincez le condenseur

par l’arrière avec de

l’eau pour enlever les

dépôts de peluches.

ETAPE 4.

Remontez le condenseur

- veillez à enfoncer le bloc

à fond, à rattacher

solidement les 3 agrafes

et à orienter les flèches

de positionnement à

l’avant du condenseur

vers le haut.

ETAPE 1.

Ouvrez le couvercle du

condenseur

- tenez la poignée et tirez

vers vous.

ETAPE 2.

Retirez le condenseur en

tournant les 3 agrafes et

en le tirant vers vous.

(Les tubes peuvent

contenir un peu d’eau ;

ceci est normal).

Tournez les 3 agrafes

Données relatives au produit... (règlement UE n°392/2012)

Capacité nominale pour le programme standard coton à pleine charge 8 kg Classe d'efficacité énergétique B

Consommation d'énergie annuelle pondérée (AE

c

) 559.8 kWh

Consommation annuelle sur la base de 160 cycles de séchage pour le programme coton standard à pleine et à demi-charge,

et de la consommation des modes à faible puissance. La consommation réelle d'énergie par cycle dépend des conditions

d'utilisation de l'appareil.

Ce sèche-linge domestique à tambour est un Sèche-linge automatique à condensation

Consommation d'énergie : pleine charge E

dry

4.70 kWh, demi-charge E

dry1/2

2.59 kWh

Consommation d'électricité : mode arrêt (P

o

) 0.14 W, mode laissé sur marche (P

l

) 2.77 W

Durée du mode laissé sur marche pour le système de gestion de la consommation d'électricité 30 minutes

Programme coton standard convenant au séchage des articles en coton normalement humides offrant le meilleur rendement

en termes de consommation électrique pour les articles en coton à pleine et à demi-charge Coton - Sec pour placard.

Durée du programme (minutes) : pondérée (T

t

) à pleine et demi-charge 95, à pleine charge (T

d

ry

) 127, à demi-charge (T

dry1/2

) 71

Classe de rendement de condensation B

Rendement moyen de condensation (%) : à pleine charge (C

dry

) 84, à demi-charge (C

dry1/2

) 78, pondérée (C

t

) à pleine et demi-charge 81

Niveau de puissance acoustique 69 dB(A) re 1 pW

Retrouvez ces données sur le site Internet : http://www

.hotpoint-ariston.com/ha/

La page charge ...

HOTPOINT/ARISTON TCF 87B 6HY/N (EU) Mode d'emploi

Ce manuel convient également à

HOTPOINT/ARISTON TCF 87B 6HY/N (EU) Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents