Regency Skope E110 Le manuel du propriétaire

919-922 (April 2019)

Instructions for Use, Installation & Servicing

For use in US and CA.

Consignes d’installation et d’utilisation

À utiliser aux É-U et au CA.

IMPORTANT

THE HEATER OUTLET GRILLE BECOMES VERY HOT

WHILE IN OPERATION.

DO NOT COVER THE OUTLET GRILLE OR ANY PART OF

THE APPLIANCE.

For use with 120V 60Hz electricity supply only.

Please read these instructions carefully before installation.

Failure to follow them could result in serious injury.

SAVE THESE INSTRUCTIONS: Leave this manual with the appliance,

they will be needed when maintenance or servicing is required.

THIS APPLIANCE MUST BE GROUNDED

IMPORTANT

LA GRILLE D'ÉVACUATION DU SYSTÈME DE CHAUFFAGE

DEVIENT TRÈS CHAUDE LORS DU FONCTIONNEMENT.

NE PAS COUVRIR LA GRILLE D'ÉVACUATION NI TOUTE

AUTRE PARTIE DE L'APPAREIL.

Pour utilisation uniquement avec une alimentation électrique de 120V,

60Hz.

Veuillez lire ces instructions avec attention avant de procéder à

l’installation.

Ne pas les suivre pourrait entraîner des blessures graves.

CONSERVEZ CES INSTRUCTIONS: Laissez ce manuel avec l'appareil, ils

seront nécessaires lorsque l'entretien ou l'entretien est nécessaire.

CET APPAREIL DOIT ÊTRE RELIÉ À LA TERRE

Skope Multi -Sided Electric LED Fireplace

Cheminée à LED murale multifaces Skope

Model/ modèle:

E110

2

User Instructions...................................................3

1. Important Information & Health and Safety........................3

2. Operating Instructions........................................................4

3. Maintenance.......................................................................9

Installation Instructions........................................11

Technical Specifications.........................................................11

Appliance Dimensions............................................................11

Installation..............................................................12

1. General...............................................................................12

2. Fitting the Appliance...........................................................12

3. Wiring Kits...........................................................................13

4. Mounting Bracket................................................................15

5. Custom Built Installation.....................................................15

6. Corner Installation (if applicable)........................................20

7. Removing the Exterior Glass..............................................24

8. Fuel Effect............................................................................24

9. Completion of Assembly......................................................26

Servicing.................................................................27

1. Fault Finding........................................................................27

2. Servicing Requirements......................................................27

3. Removing the Exterior Glass..............................................27

4. Removing the LED Light Bar..............................................28

5. Removing the Fuel Bed.......................................................29

6. Replacing the Fuel Bed Effects Spindle.............................29

7. Replacing the Fuel Bed LED Boards..................................30

8. Replacing the Interior Glass................................................30

9. Replacing the Effects Screen..............................................31

10. Replacing the Flame Effects Spindle................................32

11. Replacing the Flame Effects LED Board..........................32

12. Replacing the Fuel Bed Motor..........................................33

13. Replacing the Flame Effects Motor..................................33

14. Replacing the Power Unit.................................................34

15. Replacing the Heater Assembly.......................................34

16. Pairing the Remote Control to the Appliance...................35

17. Resetting the Remote Control..........................................35

Wiring Diagram......................................................36

Packing Checklist.................................................37

Spare Parts List.....................................................38

Contents

Covering the following models:

Recycle in accordance with Code of

Federal Regulations (CFR), Title 40, Part

273. This device is classied as electrical

and electronic equipment

As such, it must not be disposed of with

household waste.

At the end of its useful life please take

this product to an appropriate recycling

center or collection point. You can nd

your nearest recycling drop off point

by contacting your locality’s waste

management ofce.

Safety Alert Key:

WARNING! Indicates a hazardous situation

which, if not avoided could result in death or

serious injury.

CAUTION! Indicates a hazardous situation which,

if not avoided, could result in minor or moderate

injury.

ENGLISH

Warranty

This product carries a 1 year warranty.

Please note that all warranties are effective from the date of

purchase.

Full terms and conditions are detailed in the Warranty Statement

on the Regency website www.regency-fire.com. In the event

of any conflict of information the wording on the website shall

prevail.

Important Note: Should any problems be experienced with your

product, claims must first be submitted to the Dealer where

the appliance was purchased from who will offer immediate

assistance or contact Regency on your behalf.

210-195 Skope E110 Multi Sided Electric Fireplace (43"/1100 mm)

Important : The hand-held transmitter is configured in the factory

with a unique signal code. The hand-held transmitter is ready for

use once the 2 AA batteries are installed.

If the handset loses it signal or needs to be replaced, see section

17 in the servicing section for details.

3

1. IMPORTANT

INFORMATION AND HEALTH

AND SAFETY

WARNING: Improper installation, adjustment,

alteration, service or maintenance can cause

injury or property damage. Refer to this

manual. For assistance or additional

information, consult a qualified installer.

When using electrical appliances, basic precautions should

always be followed to reduce the risk of fire, electric shock,

and injury to persons, including the following:

1.1 Read all instructions before using this appliance.

1.2 Use this appliance only as described in this

manual. Any other use not recommended by the

manufacturer may cause fire, electric shock, or

injury to persons.

1.3 DO NOT use outdoors.

1.4 NEVER use this appliance in bathrooms, laundry

rooms, or any other location where the appliance

could fall into a bathtub or pool, become damp, or

come in contact with water.

1.5 For residential use only. NOT for commercial use!

Any commercial or public use of this appliance voids

all warranties, and could cause injury.

1.6 This product is not intended to be a primary heat

source. It is for supplemental heat only.

1.7 Do not locate the appliance immediately below a fixed

receptacle outlet.

Electrical Supply Circuit Requirements

Plan the location of the appliance so that it will have

adequate electric power. A 15 AMP, 60Hz circuit is

required for 120V installation. Additional appliances

on the same circuit as this appliance may exceed the

current rating of that circuit. A dedicated circuit is not

required, but is preferred to prevent circuit breaker trips

or fuse failure.

1.8 This appliance must be grounded.

1.9 DO NOT operate any appliance with a damaged cord

or plug or after the appliance malfunctions, has

been dropped or damaged in any manner. Discard

appliance, or return to authorized service facility for

examination and/or repair.

1.10 This appliance is hot when in use. To avoid burns,

DO NOT let bare skin touch hot surfaces. Keep

combustible materials, such as furniture, pillows,

bedding, papers, clothes, and curtains at least 3 feet

(0.9m) from the front of the appliance.

1.11 Extreme caution is necessary when any appliance is

used by or near children or invalids and whenever

the appliance is left operating and unattended.

User Instructions

1.12 DO NOT insert or allow foreign objects to enter any

ventilation or exhaust opening, as this may cause

electric shock or fire, or damage the appliance.

1.13 To prevent a possible fire, DO NOT block air intakes

or exhaust in any manner. Doing so could cause a

fire. DO NOT use on soft surfaces, like a bed, where

openings may become blocked.

1.14 As the appliance has hot and arcing or sparking

parts inside, DO NOT use it in areas where gasoline,

paint, or flammable liquids are used or stored.

1.15 AVOID FIRE! Regularly inspect all air vents to make

sure they are free from dust, lint, or other blockage.

Unplug the unit and clean with a vacuum ONLY. DO

NOT rinse or get wet.

1.16 DO NOT USE this appliance with any solid state

speed control devices.

1.17 Risk of electric shock! DO NOT OPEN! No user-

serviceable parts inside!

1.18 NEVER modify this appliance. Doing so could result

in personal injury or property damage. Modification of

this fireplace completely voids all warranties.

1.19 NEVER leave this appliance unattended. To

disconnect appliance, ALWAYS turn controls to

“OFF” then remove plug from outlet or turn off circuit

when not in use.

1.20 ALWAYS turn this appliance off before unplugging it

from the outlet.

1.21 To prevent a possible fire, do not burn wood or other

materials in this appliance.

1.22 ALWAYS disconnect this unit from the power supply

before performing any assembly or cleaning, or before

relocating the electric fireplace.

1.23 Always use properly grounded, fused and polarized

outlets.

1.24 Always use ground fault protection where required

by electrical code.

1.25 Avoid use of another extension cord (besides the

one supplied with this appliance) because an extension

cord may overheat and cause a fire. If you have to

use an extension cord, the cord should be N.14 AWG

minimum size and rated to not less than 1875watts.

1.26 NEVER plug this appliance into an outlet that is old,

cracked, or has any loose wires or connections.

Plugging this appliance into a faulty outlet could result

in electric arcing within the outlet that could cause the

outlet to overheat or catch fire.

ENGLISH

4

This device complies with Industry Canada licence-

exempt RSS standard(s). Operation is subject to the

following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

Under Industry Canada regulations, this radio transmitter

may only operate using an antenna of a type and maximum

(or lesser) gain approved for the transmitter by Industry

Canada. To reduce potential radio interference to other users,

the antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (e.i.r.p.) is not more

than that necessary for successful communication.

This appliance has been approved to the following

standards:

· ICES-003:Issue 6 - Information Technology Equipment

(Including Digital Apparatus) -- Limits and Methods of

Measurement

· ANSI C63.4:2014 - American National Standard for

Methods of Measurement of Radio-Noise Emissions

from Low-Voltage Electrical and Electronic Equipment

in the Range of 9 kHz to 40 GHz

· ANSI C63.10:2013 - American National Standard of

Procedures for Compliance Testing of Unlicensed

Wireless Devices

· 47 CFR Part 15, Subpart B - Radio Frequency

Devices

· 47 CFR Part 15, Subpart C 15.231 - Radio Frequency

Devices

· C22.2 No 46-13 - Electric Air Heaters

· UL 2021 (4th Edition) - Fixed and Location-Dedicated

Electric Room Heaters

· FCC Rules 15C - Federal Communication Commission

· RSP-100 - Labelling Requirements for IC

· RSS-102 Issue 5 (March 2015) - Radio Frequency

(RF) Exposure Compliance of Radiocommunication

Apparatus

· RSS-210 Issue 9 (November 2017) - Licence-Exempt

Radio Apparatus: Category I Equipment

· RSS-Gen Clause 4.6.1 - General Requirements for

Compliance of Radio Apparatus

1.27 DO NOT run power cord under carpeting. DO NOT

cover power cord with throw rugs, runners, or similar

coverings. DO NOT route power cord under furniture

or appliances. Arrange power cord away from traffic

area, and where it will not be tripped over.

1.28 ALWAYS check your appliance cord and plug

connections with each use!

A. MAKE SURE the plug fits tight in the outlet! Faulty

wall outlet connections or loose plugs can cause the

outlet to overheat.

B. Appliances draw more current than small

appliances. Overheating may occur even if it has not

occurred with the use of other appliances.

C. During use check frequently to see if the plug

outlet is HOT! If the outlet or faceplate is HOT,

discontinue use immediately and have a qualified

electrician inspect and/or replace the faulty outlets.

1.29 SAVE THESE

INSTRUCTIONS.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference,

and

(2) This device must accept any interference received,

including interference that may cause undesired

operation.

Note: This product has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This product generates, uses, and

can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this product does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and

receiver.

—Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV

technician for help.

Please take attention that changes or modification not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This equipment should be installed and operated with a

minimum distance 8" (203 mm) between the radiator and your

body

User Instructions

ENGLISH

5

2. OPERATING

INSTRUCTIONS

WARNING! Do not operate the appliance if it is

damaged or has malfunctioned. If you suspect

the appliance is damaged or has

malfunctioned call a qualified service

technician to inspect the appliance, and

replace any part of the electrical system if

necessary, before reuse.

Do not disconnect the power at the main supply

while the appliance is running. Use the functions on

the remote to turn the fire off and ensure the on/off

switch has been moved to the off position before

disconnecting.

GENERAL

2.1 The appliance can be operated by the remote control

handset or the manual controls which are on the right

hand side of the viewing window.

NOTE: To use both remote and manual

functions the manual on/off switch must be in

‘ON’ position. In order to prevent the product

becoming too hot, there is a 10s delay when

turning on the heater and a 10s delay when

turning off the heater fan.

The manual button controls basic functions, not

a full range of controls. Use the remote hand set

to carry out all functions.

PREPARATION BEFORE USE

Batteries:

2.2 Ensure that the handset batteries are new and inserted

correctly.

2.3 Dispose of old batteries at an appropriate recycling

facility.

LOCATION OF POWER SWITCH

2.4 The main power switch is located on the control panel

located on the right-hand side of the viewing window,

see Section 2a.

2.5 Switch ON (—) before operating either the remote or

manual controls.

2.6 A long beep is heard to indicate the fire is ready for

use.

2a. Manual Control Panel

2a.1 The manual controls on appliance are located at the

upper right of appliance.

1

Front View

Side

Top

2a.2 Turning on the appliance with the main power switch

on ‘—‘ position. A long beep will be heard.

2a.3 Press “LIGHTS ON/OFF” to turn on or turn off both the

flame and fuel bed at the same time.

2a.4 There are 3 flame color options:

Press “FLAME” button to select the color of flame or

return to the OFF position.

2a.5 There are 14 fuel bed color options:

Press “FUEL BED” button to select the color of fuel

bed or return to the OFF position.

Main Power

(On/Off) Switch

Fuel bed

setting button

Flame setting

button

All Lights

On/ Off button

Reset Button for

Remote Control

Heater Running

Indicators

2

LAYOUT MAY VARY

Note: The appliance will lose the memory for the

light functions when the switch is set to the Off

Position or the remote runs out of power.

Heater Running Indicators (see Diagram 1)

2a.6 When the fan heater is used in conjunction with the

flame or fuel bed effects the heater running indicators

will light up for 10 seconds.

The LEDs will illuminate for 10 seconds if the flame or

fuel bed effect is On.

If the fan heater is used independently, the heater

running indicators will stay on.

User Instructions

ENGLISH

6

Reset Button for Remote Control

2a.7 If the handset loses signal or needs to be replaced

then, see Section 17 in Servicing Section for

details.

2b. Remote Controls

The remote control should be left on a flat surface

in the room where the appliance is installed and

away from any direct flow of hot air.

Timer in

Normal Mode

Flame

Power

Heating/ Advance

Mode

Temperature Sensor

Convection

Display

Fuel Bed

3

Heating

Period

Battery

Power

Actual Room

Temperature

Timer Mode

Advance

Temperature

Setting

Time and

Day

4

Comfort

Setting

Signal Code

2b.1 The remote control works by radio signal.

The handheld transmitter is configured in the factory

with a unique signal code.

IMPORTANT: If the handset loses signal or needs

to be replaced, see Section 17 in Servicing Section

for details.

Turn on/off

2b.2 Press button to turn on the flame effect.

2b.3 Press button to turn off all the functions under the

normal heating control mode including flame effect and

fan heater.

2b.4 Press button to turn off the flame effect under

daily and week timer heating mode.

Week Days/ Time/ Comfort Temperature and change

between Celsius/Fahrenheit

On activation it is recommended that the clock is reset

to the correct time to ensure accuracy of the appliance

operation.

2b.5 Hold the button for 3 seconds to enter the setting

screen.

2b.6 Press the ‘’ or ‘’ button to choose setting to

change.

The selected character will be highlighted, see Diagram

5.

5

2b.7 Press the ‘+’ or ‘-’ button to adjust the number.

Time: 24-hour system.

Select Comfort temperature from 15-25℃/ 59-77℉.

Celsius/Fahrenheit : ℃/℉.

2b.8 Press the button for 3 seconds or wait 10 seconds

to save and exit the week, time and heating temperature

setting.

Daily Timer Heating

2b.9 The following heating periods have been preset, these

can be altered if desired:

06:00 until 08:00

17:00 until 22:00

2b.10 Press until shows at the upper right corner of

the screen to enter the daily timer heating mode.

6

User Instructions

ENGLISH

7

User Instructions

2b.11 Hold the button for 6 seconds to enter the daily

heating setting.

A maximum of 3 timed heating periods can be set per

day.

2b.12 Press ‘’ or ‘’ to choose hour or minute.

2b.13 Press ‘+’ or ‘-’ to set the number.

The minute increment / decrement by 15min per press.

7

2b.14 Hold the button for 3 seconds or wait for 10

seconds to save and exit the heating time period

setting.

2b.15 Check the timer setting. Press to check the daily

timer mode.

2b.16 If the heating needs to be turned off, it will be

necessary to go back to the Normal Control Mode to it

turn off.

When in Daily Timer Mode switching the appliance

off with the remote will stop the light output. The

heat output will continue according to the timer

settings.

Adjusting the Set Temperature

2b.17 Press the ‘+’ or ‘-’ button to increase or decrease the

temperature on the basis of COMF temperature.

COMF means the actual temperature is the same as

setting.

ECO means the actual temperature is 2℃/4℉ lower

than the setting temperature.

ECO- means 4℃/7℉ lower, COMF+ means 2℃/4℉

higher.

COMF++ means 4℃/7℉ higher.

Adaptive start control

According to room temperature and set-pointed

temperature, the heater will automatically determine

the appropriate time to heat to ensure that it will reach

the set-pointed temperature in the set time (up to 45

minutes prior to the set time).

Flame Color Adjustment

2b.18 Press button to enter the flame adjustment

screen.

There are 3 flame color options, indicated by the

number shown in Diagram 7.

There are 6 levels of brightness, including off. This is

indicated by the bar, with the blank bar indicating off,

see Diagram 8.

8

Brightness

Level

Color

Option

2b.19 Press the ‘’ or ‘’ button to cycle through the flame

color options.

2b.20 Press the ‘+’ button to increase the flame brightness.

Press the ‘-’ button to decrease the flame brightness

until off.

Fuel Bed Color Adjustment

2b.21 Press to enter the fuel bed light adjustment

screen.

There are 14 fuel bed color options, indicated by the

number shown in Diagram 8.

There are 6 levels of brightness, including off. This is

indicated by the bar, with the blank bar indicating off,

see Diagram 9.

9

Brightness

Level

Color

Option

2b.22 Press the ‘’ or ‘’ button to cycle through the fuel

bed color options.

2b.23 Press the ‘+’ button to increase the fuel bed brightness.

Press the ‘-’ button to decrease the fuel bed brightness

until off.

ENGLISH

8

User Instructions

Normal Control Mode

2b.24 Normal Control Mode is the default setting.

Alternatively press button until the logo is

shown at the upper right corner of the screen, see

Diagram 10.

10

2b.25 Press the ‘+’ or ‘-’ button to adjust the setting

temperature from 17℃ to 25℃/ 59℉ to 77℉.

2b.26 Press button to turn the heat on/off, ON

or OFF will show at the lower right corner of the

screen, see Diagram 11.

11

Note: It is normal for the fan heater to stop running for

periods of time. This happens if the room temperature

is higher than the temperature set on the control.

The heater indicator will be turned off after 10s if the

flame is switched ON. The heater indicator will stay ON

if only the heating function is used.

When in Normal Control Mode switching the

appliance off with the remote will stop both the

light and heat output.

Count Down Timer

This setting is only in normal heating control mode. It

allows the appliance to be returned to Standby after a

set period of time. The heater must be switched on to

use this function.

2b.27 Press to cycle through the setting from Off and 0.5

hours to 9 hours. Timer logo and remaining time will

show on the screen.

The heater of appliance can be automatically run by

using daily timer and weekly timer on the remote.

Battery

The battery power level is indicated at the top right of

the remote control screen, see Diagram 4.

Battery Full No action required

Battery Half Power Ensure new batteries are available.

Battery Empty Replace batteries immediately

Battery replacement is recommended after 1 year. The

Remote requires two 1.5V alkaline AAA batteries.

Changing the batteries will not affect the Timer

Mode settings, however, the clock may need

adjusting.

Week Timer Heating

2b.28 The following heating periods have been preset, these

can be altered if desired:

From Monday to Friday

06:00 until 08:30

17:00 until 22:00

From Saturday to Sunday

06:30 until 09:30

11:00 until 13:00

17:00 until 22:00

2b.29 Press until shows at the upper right corner of

the screen to enter the week heating mode.

12

2b.30 Hold the button for 6 seconds to enter the week

timer heating mode setting.

2b.31 Press ‘’ or ‘’ to move the cursor (a flashing

underline).

2b.32 Press the button in the corresponding week

position to select (the character is highlighted) or

cancel (the character is displayed normally) the current

setting, the same time period can be selected together.

13

ENGLISH

9

2b.33 Press the ‘’ button to move the cursor to the time

period setting area.

2b.34 Press ‘’ or ‘’ button to choose hour or minute.

2b.35 Press ‘+’ or ‘-’ to set the number.

A maximum of 3 timed heating periods can be set per

day.

Minute increment / decrement by 15min per press.

2b.36 Press to set the heating time for the selected day

and return to the week line.

2b.37 Hold the button for 3 seconds or wait for 10

seconds to save and exit the heating time period

setting.

2b.38 Press ‘’ or ‘’ to check the timer setting for the

week timer heating mode.

2b.39 If the heating needs to be turned off, it will be

necessary to go back to the Normal Control Mode to it

turn off.

When in Weekly Timer Mode switching the

appliance off with the remote will stop the light

output. The heat output will continue according to

the timer settings.

Adjusting the Set Temperature

2b.40 Press the ‘+’ or ‘-’ button to increase or decrease the

temperature on the basis of COMF temperature.

COMF means the actual temperature is the same as

setting.

ECO means the actual temperature is 2℃/ 4℉ lower

than the setting temperature.

ECO- means 4℃/ 7℉ lower.

COMF+ means 2℃/ 4℉ higher.

COMF++ means 4℃/ 7℉ higher.

Adaptive start control

According to room temperature and set-pointed

temperature, the heater will automatically determine

the appropriate time to heat to ensure that it will reach

the set-pointed temperature in the set time (up to 45

minutes prior to the set time).

User Instructions

Advance mode

2b.41 The heating state can be advanced to the next period

is under both the daily and week timer heating mode.

14

If the heater is on in the current period, pressing the

button will turn the heater off.

If the heater is off in the current period, pressing the

button will turn the heater on.

Whether the actual heating will be on/off also depends

on the room temperature and setting temperature.

2b.42 Press to enter the Advance mode under the

daily and week timer heating mode, will show at

the upper right corner of the screen.

2b.43 Press again or timer period ends will exit the

Advance mode.

Window open detecting

2b.44 When the transmitter detects a rapid drop in room

temperature, it will be judged as an open window: the

warning icon will be displayed and the heating will be

turned off automatically.

15

2b.45 After indoor temperature rise or manual intervention

(by operating remote control), it will return to normal

working state.

ENGLISH

10

3. MAINTENANCE

3.1 ALWAYS UNPLUG FROM MAIN SUPPLY

BEFORE CLEANING OR UNDERTAKING ANY

MAINTENANCE.

GENERAL CLEANING

3.2 Only clean the outer casing when it is cold. Do not use

abrasive cleaners.

CLEANING GLASS

3.3 Wipe the glass viewing panel with a damp cloth and

buff with a lint free duster.

Caution: Do not use abrasive cleaners on the

glass panel. Do not spray liquids directly onto any

surface of the unit.

CLEANING THE FUEL EFFECT

To access the fuel effect it will be necessary to remove

the glass viewing panel.

3.4 Ensure the appliance is unplugged.

3.5 There is a clamp at the top of each corner of the glass

viewing panel that secure the glass in place,

see Diagram 15.

15

3.6 Supporting the glass, loosen and remove the 2 clamps.

These can be unscrewed using just finger tips.

3.7 Carefully tip the glass forward and lift out of the lower

tray to remove from the appliance, see Diagram 16.

16

User Instructions

ENGLISH

The fuel effect can now be accessed.

3.8 Remove and wash the fuel effect to remove any dust

particles. Alternatively clean with a lint free duster.

Ensure that the effect is dry before replacing.

Replace the fuel effect see Installation Instructions

Section 5 for layout.

3.9 Replace the glass following the instructions in reverse

order.

When replacing the clamps ensure that the tabs on

the clamps locate in the slots on the appliance, see

Diagram 17.

17

CLEANING AIR INLETS

3.10 Ensure the appliance is unplugged.

3.11 Clean the air inlet and outlet grilles regularly with a soft

cloth or the nozzle of a vacuum cleaner.

Air Outlets

18

Air

Inlets

Air

Inlets

Front View

Top

Side Side

Dust build-up can inhibit efficient performance of

the fan and lead to the safety cut-out operating.

3.12 Keep the area around the appliance clean and free of

fluff, dust or pet hair.

3.13 In particular, build-up of dust etc. can occur around the

heater area. Take particular care to keep this area free

from such particles on a regular basis to prevent build-

up.

BATTERY REPLACEMENT

3.14 When the remote battery is low it must be changed

immediately. Install correct replacement and dispose

of the old battery carefully at an appropriate recycling

facility.

11

Installation Instructions

A 120V 12.5A 60Hz supply is required

Rated power consumption:

Skope E110: 1500 Watts

THIS APPLIANCE MUST BE GROUNDED

IMPORTANT: This appliance must be on its own

dedicated circuit with a minimum 15 amp electrical

supply.

FAILURE TO DO SO WILL INVALIDATE YOUR

WARRANTY.

These instructions cover the following models:

Model

A B C D E F

mm in mm in mm in mm in mm in mm in

Skope E110 1154

45

7

/

16"

1110

43

11

/

16"

1100

43

5

/

16"

1116

43

15

/

16"

352

13

7

/

8"

569

22

3

/

8"

Model

G H I J K

mm in mm in mm in mm in mm in

Skope E110 80

3

1

/

8"

135

5

/

16"

220

8

11

/

16"

238

9

3

/

8"

276

10

7

/

8"

TECHNICAL SPECIFICATION

A 3 prong plug with 72" power lead and a separate

hard wiring kit are supplied.

2 x Remote control handset battery (AAA)

Note: The hard wiring from the appliance to the breaker must

be supplied by a qualified electrician. This is not supplied

with the appliance

For Packing Checklist, see Page 28.

Control System Technical Data

Main Control Board Remote Receiver Board Remote Control

Hardware RC01-041A01 V2 RF290B V1.2 RF290A-TX V1.3

Software RC01-041A01 V2 - RF290C V06.0.HEX

Frequency - - ASK/OOK 433.92MHz

Maximum Transmit Power - - 10mW

B

C

H

I

J

K

G

D

A

E

56

F

120V connection

Front

View

Front

Rear

Front

Rear

210-195 Skope E110 Multi Sided Electric Fireplace (43"/1100 mm)

ENGLISH

12

Installation Instructions

1. GENERAL

1.1 TOOLS REQUIRED

A Screw Driver and Drill will be needed.

1.2 UNPACKING THE FIREPLACE

WARNING! DO NOT use this appliance if any part

has been exposed to water.

Immediately call a qualified service technician to

inspect and to replace any part of the electrical system

if necessary.

1.3 Open the packaging carefully and remove the

polystyrene.

Remove and discard the plastic bag.

Keep plastic wrapping away from children.

Be responsible when handling the packing materials.

1.4 Check all parts and accessories are removed before

disposing of any packaging.

If necessary keep the original packaging for future

transport and/or storage.

2. FITTING THE APPLIANCE

ENSURE THAT THE MAIN SUPPLY IS ISOLATED.

2.1 Locating the Skope

Your new Skope may be installed virtually anywhere in

your home. However, when choosing a location ensure

that the general instructions are followed.

2.2 For best results, install out of direct sunlight.

2.3 Make sure there are no pipes or cables behind the

area to be drilled or cut.

2.4 Before installation ensure that the wall is suitably

constructed to support the weight of the appliance.

When the appliance is installed into a decorative

enclosure, it will be necessary to provide

ventilation to the upper section of the appliance

outer casing with a free area of no less than

8.13sq.in (52.5cm

2

). This should be positioned in

the underside of the top section to either or both

sides of the glass.

2.5 The appliance should ideally be located close to a

suitable main receptacle to enable connection. An

extension could be run from an existing receptacle

outlet but this must be carried out by a suitably

qualified electrician.

The electrical receptacle must be easily accessible to

allow disconnection when the appliance is installed.

ENGLISH

2.6 If access to the underside of the appliance will be

limited after installation is complete, ensure the plug

connection on the underside of the appliance has been

considered.

This appliance must be fixed to the wall using

the wall mounting bracket provided, see Section

4 for details.

Note: If installing the appliance into a custom

built corner installation the side brackets will

need to be replaced with the 2 brackets supplied,

see Section 6.

2.7 Electrical Supply Circuit Requirements

Plan the location of the appliance so that it will have

adequate electric power. A 15 AMP, 60Hz circuit is

required for 120V installation. Additional appliances

on the same circuit as this appliance may exceed the

current rating of that circuit. A dedicated circuit is not

required, but is preferred to prevent circuit breaker trips

or fuse failure

2.8 If the power cord is damaged, it must be repaired

by the manufacturer, its authorised service centre or

professional person.

2.9 The product is a zero clearance design.

2.10 Ensure that curtains and furniture are not positioned

close to the chosen position, as this would create a

potential fire hazard or block the heater outlet ducts.

WARNING! KEEP ALL COMBUSTIBLE MATERIALS

AT LEAST 3' (0.9M) FROM THE FRONT OF THE

ELECTRIC FIREPLACE.

Optional Extras

2.11 This appliance can be installed with an optional

decorative trim to finish the installation, see Diagram 1.

For details please contact your Regency retailer.

See installation of this decorative trim in section 5.14

(Center trim and or 6.12 (corner trim)

Product Code Description

910-146 Skope E110 Centre Metal Trim

910-124 Skope E110 Left Hand Corner Metal Trim

910-135 Skope E110 Right Hand Corner Metal Trim

1

Top View

Front

Side

13

3. WIRING KITS

This appliance has already been pre-wired to accept

a 3 prong plug. It also has the option of being hard

wired to the main supply depending on the desired

installation.

Important : When using a 3 prong plug ensure that

wherever this is located that it is accessible. This

cannot be enclosed as there must be access to the

receptacle and 3 prong plug.

This appliance must be connected and grounded in

accordance with local codes, if hard wired. In the absence

of local codes, the use the current CSA C22.1 CANADIAN

ELECTRICAL CODE in Canada or the current ANSI/NFPA 70

NATIONAL ELECTRICAL CODE in the United States.

Hard Wiring

3.1 Remove the 2 screws securing the wiring plate on the

bottom right hand side of the appliance, see Diagram

2.

2

Underside of Appliance

3.2 The wiring kit is attached to the power unit inside the

appliance, see Diagram 3.

3

3.3 Feed the hard wire cable through the large hole in the

plate and hold in place with the grommet.

ENGLISH

Installation Instructions

3.4 Insert a screwdriver into the holes on the top of the

wiring block to open the connectors for Live, Earth and

Neutral.

4

Red

Yellow

Green

Blue

Black

White

3.5 Insert the correct wires into the wiring block.

3.6 Replace the wiring plate, rotating the orientation so the

large hole is covered by the metalwork of the casing

and secure with the screws, see Diagram 5.

5

3.7 The other end of the power cable can now be hard

wired into the main.

NOTE: Isolate the power supply when completing

the installation. The breaker should also be marked

to indicate electric fireplace for ease of serving this

appliance

14

4. MOUNTING BRACKET

The wall mounting bracket will need to be separated

from the appliance.

4.1 Lay the appliance face down on a soft flat surface to

avoid damage.

4.2 Unscrew the mounting bracket from the upper left and

right sides of the appliance, see Diagram 12.

Retain the screws as they will be required during

installation.

6

4.3 Make sure there are no pipes or cables behind the

area to be drilled.

4.4 Decide on the desired height from the floor level to the

bottom of the heater unit.

4.5 The bottom of the wall bracket measures from the

bottom of the appliance, see Diagram 13.

7

A

Appliance A

E110 485mm 19

1

/

8"

Rear View

Side

Top

4.6 To prepare the installation measure the distance from

floor level and using a level draw a line (A dimension)

higher than the intended position of the bottom of the

appliance.

4.7 Position the wall mounting bracket so that the bottom

edge is level with the line drawn on the wall.

4.8 Mark the position of the fixing holes on the wall, see

Diagram 14.

8

4.9 Secure the mounting bracket to a solid wall using the

screws provided. Ensure that the folds on the bracket

are projecting up. If this is going to be installed into

drywall, use the drywall anchors provided.

4.10 Attach the bracket to the wall using the screws

provided ensuring the folds are projecting up, see

Diagram 15.

9

4.11 Lift the appliance onto the bracket.

Ensure the folds locate into the slots on the back of the

appliance, see Diagram 16.

10

4.12 Secure with 2 screws at either side of the bracket, see

Diagram 17.

Note: if a corner application you will only have access

to the open side to secure screw.

11

Installation Instructions

ENGLISH

15

Installation Instructions

4.13 Fasten the two lower fixing bracket to the 2 fixing

points on the underside of the appliance and secure to

the wall using anchors (if required), see Diagrams 18 &

19.

12

Underside of Appliance

13

Underside of Appliance

5. CUSTOM INSTALLATION

The Skope has been designed so that it can be fitted onto a

masonry wall or into a custom built studwork enclosure.

The appliance should ideally be fitted into/onto an internal flat

wall which has already been constructed from either wood

studs and drywall or block/brick. Please ensure that suitable

anchors are used when securing to any hollow or purpose

built cavity.

Note: If installing the appliance into a custom

built corner installation the side brackets will

need to be replaced with the 3 Corner Side Glass

Retainer brackets supplied, see Section 5 for

fitting details.

This appliance is designed so combustible or non-

combustible building materials may be used to finish up to

the appliance casing.

The product is a zero clearance design.

Ensure that the stud or any materials used to seal the cavity

(if required) do not obstruct the air vents on the top and sides

of the appliance.

DO NOT PACK THE VOID AROUND OR ABOVE THE

APPLIANCE WITH INSULATION MATERIALS SUCH AS

MINERAL WOOL.

NOTE: REMOVING THE SIDE GLASS PANELS WILL

NOT BE POSSIBLE FOLLOWING THIS INSTALLATION

METHOD.

This product can be installed in the following configurations:

Non Recessed - the appliance is attached to a wall and

studwork enclosures are built top and bottom and also

anchored to the wall.

This can be finished with 3 sides of glass Left, Right and

Front visible or as a corner installation with Front and Left or

Right glass panel visible depending on location.

Semi Recessed - the appliance can be built into a false

chimney breast in order to hide the depth of the Black Glass

Area leaving only the clear viewing area of the glass visible.

This can be finished with 3 sides of glass Left, right and Front

visible or as a corner installation with front and left or right

glass panel visible depending on location.

3 Sided Installation

- non recessed

Note: All finished facing material should butt up cleanly

to the flanges around the firebox opening.

Rough edges will be visible from the front

view. To maintain a clean finished edge - it is

recommended to install the combustible facing

material with the finished edge against the

fireplace. Alternatively use trim or metal corner

bead to cover cut edges of the facing material. 

51 Position the mounting bracket in the desired location

and fit the appliance.

Upper Enclosure

5.2 The upper enclosure can either create a floating shelf

effect or a false chimney breast housing, see Diagram

14.

14

Floating

shelf

style

Min 6

7

/

8

in

(175mm)

False

Chimney

Breast

Front View

ENGLISH

16

Installation Instructions

Ventilation to the upper section enclosure with a

free area of no less than 8.13sq.in/ 52.5cm

2

must

be provided.

Vent(s) should be positioned on the underside

of the top section of the enclosure close to the

glass side(s). This can be positioned to one side

of the appliance as a large singular vent or two

smaller ones on either side this will determine the

size and shape of the enclosure, see Diagram 15.

15

Min

3

1

/

8

in

(80mm)

Min

6

9

/

16

in

(40mm)

Single Sided Vent Configuration (Left or Right)

Min

2

1

/

8

in

60mm

Min

2

1

/

8

in

60mm

Two Sided Vent Configuration

Front View

Large

Single

Vent

Small Vents

5.3 Build the framework for the upper enclosure to the

desired size, see Diagram 16.

Note: The following dimensions shown are only

minimums. The top enclosure can be increased in

overall size in depth,height and width using a wide

variety of materials

16

48

11

/

16

in 1236 mm

Minimum

6

7

/

8

in

175 mm

Minimum

11

5

/

8

in 296 mm

Minimum

5.4 Finish the bottom of the studwork with suitable

boarding cut to fit around the viewing area, see

Diagram 17.

17

43

15

/

16

in (1116mm)

11

5

/

8

in

(296mm)

Minimum*

10

3

/

8

in

(263mm)

48

11

/

16

in (1236mm) Minimum*

Vent Cutout -

see table

W*

D*

Side

Front

Side

NOTE: A cutout needs to be made to

accommodate the heater vent in the top fascia of

the appliance, see Diagram 18 and table.

18

Heater Vent cutout -

position varies for each

appliance

Vent Cutout Dimensions

Width (W*) Depth (D*)

360mm 14

3

/

4"

25mm 1

"

5.5 Attach the enclosure to the wall ensuring that

there are sufficient anchor points and the wall is

constructed from a suitable load bearing material

that can support the weight of the chosen material

and size, see Diagram 19.

19

5.6 Finish the remaining studwork with drywall and vents.

ENGLISH

17

Lower Enclosure

5.7 The lower enclosure can either create a floating shelf

effect or a false chimney breast housing, see Diagram

20.

20

Floating

shelf

style

Min

3

15

/

16

in

100mm

deep

False

Chimney

Breast

Min

1

9

/

16

in

(40mm)

Min

1

9

/

16

in

(40mm)

Floor Level

Front View

NOTE: When designing the lower enclosure it

may be aesthetically best to match or exceed the

dimensions of the upper enclosure.

5.8 Build the framework for the lower enclosure to the

desired size, see Diagram 21.

Note: The following dimensions shown are only

minimums. The bottom enclosure can be increased

in overall size in depth,height and width using a

wide variety of materials

21

48

11

/

16

in 1236 mm

Minimum

11

5

/

8

in

296 mm

Minimum

3

15

/

16

in

100 mm

Minimum

Installation Instructions

5.9 Finish the top with suitable board material cut to fit

around the viewing area, see Diagram 22.

22

43

15

/

16

in (1116mm)

11

5

/

8

in

(296mm)

Minimum*

8

3

/

4

in

(222mm)

48

11

/

16

in (1236mm) Minimum*

Side

Front

Side

5.10 Ensure provision is made for the power cable and

lower fixing brackets when constructing the lower

enclosure.

5.11 The lower enclosure can locate over or under the lower

flange on the product, see Diagram 23.

Locate under the flange if fitting the optional decorative

trims.

NOTE: If fitting over the flange the material for

this piece must be a maximum thickness of

5

/

8

in

(16mm).

Thicker material will prevent the removal of the

front glass for cleaning and servicing.

23

5.12 Attach the enclosure to the wall ensuring that

there are sufficient anchor points and the wall is

constructed from a suitable load bearing material

that can support the weight of the chosen material

and size.

5.13 Finish the remaining studwork with drywall.

ENGLISH

18

5.14 Place the optional decorative trim on top of the

studwork enclosure and butt up to the edge of the

glass.

24

Optional

Decorative Trim

Side Infills

5.15 Following creation of the top and bottom enclosures

the dark areas of the side panels will still be visible,

see Diagram 25.

25

Side View

Installation Instructions

5.16 Once the top and bottom installation has been finished,

infills can be added to cover the dark areas of the side

panels if desired, see Diagram 26.

Note: The height of the infills will be the distance

between the Upper and Lower flanges minus the

thickness of the non-combustible board used to create

the base enclosure top.

26

A*

B*

C: Customer

preference

Infill Dimensions

Model Height (A*) Depth (B*)

Skope E110 13

7

/

8

in (352mm) - minus

board thickness

80mm 3

1

/

8

in

Front View

Side View

ENGLISH

19

Installation Instructions

3 Sided Installation

- Semi recessed

Note: All finished facing material should butt up cleanly

to the flanges around the firebox opening. Rough

edges will be visible from the front view. To maintain

a clean finished edge - it is recommended to install

the combustible facing material with the finished edge

against the fireplace. Alternatively use trim or metal

corner bead to cover cut edges of the facing material.

5.17 The appliance has black areas on the side panels, see

Diagram 33.

27

Side View

5.18 It is possible to install into a semi recessed chimney

breast to hide these areas, see Diagram 28.

28

5.19 To do this construct a studwork wall to the desired

specification which allows the mounting bracket to be

recessed, see Diagram 29 and table.

29

Mounting Bracket

* See table

for depth

Recess Depth

Model Depth

Skope E110 80mm 3

1

/

8

in

5.20 Fit the appliance on the mounting bracket, see Diagram

30.

30

5.21 Ensure provision is made for the power cable when

finishing the studwork - it will be necessary to

access the plug for servicing.

5.22 Finish off the installation with suitable boarding, see

Diagram 31.

31

Top and Bottom enclosures can now be built following

the same method as a non recessed installation but

reduce the depth by the depth of the built in recess.

ENGLISH

20

6. CORNER INSTALLATION

(IF APPLICABLE)

If access to the underside of the appliance will be

limited after installation is complete, ensure the plug

connection has been considered.

Note: If installing the appliance into a custom

built corner installation the side brackets will

need to be replaced with the 3 Corner Side Glass

Retainer brackets supplied.

If the appliance is to be installed in a right hand

corner, the right hand brackets will need to be

replaced. If left hand, replace the left hand

brackets.

32

Brackets included:

1 x Top right bracket

1 x Top left bracket

1 x Bottom bracket

The remaining left or right top bracket may be recycled

as it will not be required

To change the brackets:

6.1 Support the bracket and remove the 3 screws,

see Diagram 33.

33

Installation Instructions

6.2 Remove the 2 screws securing the lower bracket, see

Diagram 34.

34

6.3 Fit the bottom Corner Side Glass Retainer bracket

ensuring both screws are replaced, see Diagram 35.

35

6.4 Fit the top Corner Side Glass Retainer bracket,

ensuring all 3 screws are replaced, see Diagram 36.

36

6.5 Install the appliance using the desired method and

nish.

This appliance is designed so combustible or

non-combustible building materials may be used to

finish up to the appliance casing.

The product is a zero clearance design.

Ensure that the stud or any materials used to seal the

cavity (if required) do not obstruct the air vents on the

top and sides of the appliance.

ENGLISH

La page charge ...

Regency Skope E110 Le manuel du propriétaire

Ce manuel convient également à

Regency Skope E110 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents