Samsung NK36K7000WG Manuel utilisateur

Jet Bot

User manual

VR30T85**** Series

• For full manual, Scan QR code or access online at https://www.samsung.com

• Before operating this unit, please read the instructions carefully.

• For indoor use only.

2

03

02

01

06

08

05

09

04

07

04

01

07

02

06

09

05

03

04

08

10

04

05

07

08

06

02

04

03

01

• If you want to purchase an additional Dust Bag, check the model name (VCA-RDB95) and

Samsung logo ( ) first, then contact your nearest Samsung Electronics retailer or

Samsung service center.

Spin Brush: 2units

(Inside the product:

1unit, Spare: 1unit)

Dust Bag: 2units

(Inside the product:

1unit, Spare: 1unit)

Pre-motor Filter:

2units

(Inside the product:

1unit, Spare: 1unit)

Clean Station Power cord Boundary Markers User Manual

Top

01

Obstacle Sensor

02

Power switch

03

LiDAR Sensor

04

Dustbin

05

Start/stop button

06

Docking (Recharging)

button

07

Status Indicator

08

Docking sensor window

09

Upper Cover

Bottom

01

Charging Pin

02

Brush

03

Brush Cover

04

Cliff Sensor

05

Roller

06

Battery Cover

07

Driving Wheel

08

Spin Brush

09

Empty Dust Outlet

10

Brush Cover Lock

Clean Station

01

Dust Suction Port

02

Charging Terminal

03

Status Indicator

04

Cover

05

Fine dust Filter Cover

06

Fine dust Filter

07

Power cord groove

08

Charging Signal

Transmitter

Accessories may differ depending on the models.

• For the normal use of the Jet Bot’s functions,

the SmartThings connection is required.

3

1 2

0.5 m

(1.6 ft)

0.5 m

(1.6 ft)

1 m

(3.3 ft)

3

A

4

B-1

12

B-2

1 2

3

1

4

B

OFF ON

5

1 2

3 4

5 6

7 8

1

C-1

24H

C

6

C-2

1 2

3 4

C-3

C

7

C-5

C-4

2

1

C

8

12

34

12

34

D-1

D-2

D

English

English 9

Operation and maintenance

A. Installation

NOTE

• Install the Clean Station in a place where the

floor and wall are level.

• If the power cord is too long for the

installation environment, coil the power

cord around the cable management post,

then put it in the fixing groove at the rear

of the Clean Station.

• If you reinstall the Clean Station to a new

position of 45 degrees or 1m (3.3ft) or

more from the previous installed place,

recreate the map using the SmartThings

App. (If you use the existing map, some

places may not be cleaned.)

B. Using the Jet Bot

B-1 Charging the Jet Bot

Charging

• Open the upper cover of the Jet Bot and

remove the white gasket.

• Remove the yellow gasket attached to the

power switch at the side of the Jet Bot and

press the power switch to turn the Jet Bot

on.

• Place the Jet Bot on the Clean Station

manually to start charging.

- When the Jet Bot starts charging, the

Status Indicator of the Clean Station turns

white and after 1 minute, the Status

Indicator turns off automatically. (Charging

continues though the Status Indicator has

turned off.)

• Check the charging status.

- When charging starts, the Status Indicator

of the Jet Bot turns on (red, orange, or

yellow depending on charging progress),

it rises gradually, and changes to green

when the charging is complete.

Docking (Recharging)

• You can return the Jet Bot to the Clean

Station while cleaning to recharge.

- Press the [ ] on the Jet Bot or use the

SmartThings App to select the recharging

function.

B-2 Starting cleaning

• Press the [ ] on the Jet Bot to start

cleaning in Auto Clean.

• Press the [ ] on the Jet Bot to stop

operation while cleaning.

- When pressing the [ ], the Jet Bot

returns to the Clean Station and starts

charging.

C. Cleaning the Jet Bot

Before maintenance work, you should turn off

the power switch at the side of the Jet Bot.

C-1 Emptying and cleaning the Dustbin

• Remove the dust on the filter and the

Dustbin, clean them with water, and dry

completely in the shade.

C-2 Cleaning the brush

C-3 Cleaning the Sensor Window

• Wipe the Sensor Window with a soft cloth.

C-4 Cleaning the Driving Wheel

C-5 Cleaning the Spin Brush

• If curl or deformation occurs, Cover the

Spin Brush with a hot steamed cloth for

10seconds, then wipe the Spin Brush.

D. Cleaning the Clean Station

Before cleaning the Clean Station, unplug the

power cord from the electrical outlet.

D-1 Replacing the Dust Bag

D-2 Cleaning the Fine dust Filter

• Do not clean the Fine dust Filter with water.

NOTE

For detailed methods of use and

cleaning, refer to the QR code.

English

English10

Safety information

• Before operating the appliance, please read

this manual thoroughly and retain it for

your reference.

• Because the following operating instructions

cover various models, the characteristics

of your vacuum cleaner may differ slightly

from those described in this manual.

Caution/Warning symbols used

WARNING

Indicates that a danger of death or serious

injury exists.

CAUTION

Indicates that a risk of personal injury or

material damage exists.

Other symbols used

NOTE

Indicates that the following text contains

additional important information.

State of California Proposition 65 Warning

WARNING

Cancer and Reproductive Harm

- www.P65Warnings.ca.gov.

L i - i o n

For battery recycling go to

call2recycle.org

or call 1-800-822-8837

Failure to meet these requirements could

cause damage to the internal parts of the

vacuum and void your warranty.

General

• Do not allow to be used as a toy. Close

attention is necessary when used by or near

children.

• Use only as described in this manual.

• Do not operate the Jet Bot or the Clean

Station if it has been damaged in any way.

• If the vacuum cleaner is not working as it

should, has been dropped, damaged, left

outdoors, or dropped in water, return it to a

customer care center.

• Do not handle the Clean Station or the Jet

Bot if your hands are wet.

• Use only on dry, indoor surfaces.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or

instruction concerning use of the appliance

by a person responsible for their safety.

Children should not clean or perform

maintenance on the vacuum without adult

supervision.

• Move the cords of other appliances so they

are not in the area that is to be cleaned.

• Do not operate the vacuum in a room where

an infant or child is sleeping.

• Do not operate the vacuum in an area

where there are lit candles or fragile objects

on the floor.

• Do not operate the vacuum in a room that

has lit candles on furniture that the vacuum

may accidentally hit or bump into.

• Do not allow children to sit on the vacuum.

• Do not use the vacuum on a wet surface.

• If the supply cord is damaged, it must be

replaced by the manufacturer or its service

agent or a similarly qualified person in

order to avoid a hazard.

Clean Station

• Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

• Do not use outdoors or on wet surfaces.

• Unplug the Clean Station from the outlet

when not in use and before servicing.

• Use only the Clean Station supplied by the

manufacturer to recharge.

• Do not use with a damaged cord or a plug

or a loose power outlet.

English

English 11

• Do not pull or carry by the cord, use the

cord as a handle, close the door on the

cord, or pull the cord around sharp edges

or corners. Keep the cord away from heated

surfaces.

• Do not use extension cords or outlets with

inadequate current carrying capacity.

• Do not unplug by pulling on the cord. To

unplug, grasp the plug, not the cord.

• Do not mutilate or incinerate batteries as

they will explode at high temperatures.

• Do not attempt to open the Clean Station.

Repairs should only be carried out by a

qualified customer care center.

• Do not expose the Clean Station to high

temperatures or allow moisture or humidity

of any kind to come into contact with the

Clean Station.

• Do not charge the non-rechargeable

batteries with the Clean Station.

Jet Bot

• Do not pick up hard or sharp objects such

as glass, nails, screws, coins, and etc.

• Do not use without a filter in place. When

servicing the unit, never put fingers or

other objects into the fan chamber in case

the unit accidentally turns on.

• Do not put any objects into openings.

Do not use with any openings blocked;

keep openings free of dust, lint, hair, and

anything that may reduce air flow.

• Do not pick up toxic materials (chlorine

bleach, ammonia, drain cleaner, etc.).

• Do not pick up anything that is burning or

smoking, such as cigarettes, matches, or hot

ashes.

• Do not use to pick up flammable or

combustible liquids such as gasoline or use

in areas where they may be present.

• Also do not use in:

- Locations with candles or desk lamps on

the floor.

- Locations with unattended fires (fire or

embers).

- Locations with distilled alcohol, thinner,

ashtrays with burning cigarettes, etc.

• Do not use the Jet Bot in an enclosed

space filled with vapors given off by oil

based paint, paint thinner, moth proofing

substances, flammable dust, or other

explosive or toxic vapors.

• Leaks from battery cells can occur under

extreme usage or temperature conditions.

If the liquid gets on the skin, wash quickly

with water. If the liquid gets into the eyes,

flush them immediately with clean water

for a minimum of 10 minutes. Seek medical

attention.

Power related

WARNING

• Please prevent any risk of electric shock or

fire.

- Do not damage the power cord.

- Do not pull the power cord too hard or

touch the power plug with wet hands.

- Do not use a power source other than

100-240 V~ and also do not use a multi-

outlet to supply power to a number of

devices at the same time. (Do not leave

the cord carelessly on the floor.)

- Do not use a damaged power plug, a

power cord or a loose power outlet.

• Clean dust or any foreign matter on the pin

and the contact part of the power plug.

- There is a risk of electric shock or

malfunction.

Safety information

English

English12

Before use

WARNING

• Do not use the Jet Bot near a heater or

combustible materials.

- Do not use the Jet Bot near fire or flame

such as a movable heater, a candlelight,

a desk lamp, a fireplace, etc. or in a place

where combustible materials such as

gasoline, alcohol, thinner, etc. exist.

• Make sure there are no dangerous objects

around the Jet Bot’s cleaning area to

prevent collision and unplug any electric

heaters or fans.

- The Jet Bot can be damaged or

malfunction.

• The Jet Bot is intended for household use

therefore do not use it in an attic, basement,

storage, an industrial building, out of indoor

space, places with moisture (such as a

bathroom, a laundry room), on the table or

shelves.

- The Jet Bot can be damaged or

malfunction.

• Attach the Boundary Markers to a place

where the Jet Bot may fall such as a stair or

a banister to prevent product damage and

injury.

- Please keep the Cliff Sensor clean all the

time for safety.

• Be sure the Jet Bot does not suck in or

touch any kind of liquids (water, beverage,

filth, etc.).

- The Jet Bot can be severely damaged

and it may contaminate other areas if the

wheels pass through liquid.

• Do not spill any liquids on the Clean Station.

- There is a risk of fire or electric shock.

• Do not use the Clean Station for anything

other than its intended purposes.

- There is a risk of fire or severe damage to

the Clean Station.

• Always keep the Cliff Sensor clean for your

safety.

• As this wireless installation may cause radio

interference, it cannot provide a service

related with human safety.

CAUTION

• Insert the Dustbin before using the Jet Bot.

• When installing the Clean Station, do not

leave the cord carelessly on the floor since

the Jet Bot may get tangled by it.

• To clean all areas of your house, open all

rooms and set the No-go Zones with the

SmartThings App or attach the Boundary

Markers to the places where the Jet Bot

may get damaged such as a front door, a

veranda, a bathroom, and stairs for safety.

• Follow these recommendations for proper

automatic recharging.

- Always turn on the power of the Clean

Station.

- Install the Clean Station where the Jet Bot

can easily find.

- Do not leave any objects in front of the

Clean Station.

• Do not use the Jet Bot on black colored

floors.

- The Jet Bot may not be able to operate

normally.

• Do not place any objects within 0.5m

(1.6ft) of either side of the Clean Station or

within 1m (3.3ft) of the front of the Clean

Station.

• Make sure the Clean Station’s charging

contact is not damaged or have any foreign

matter on it.

• For the very low areas where the Jet Bot

may get stuck, set the No-go Zones with the

SmartThings App or attach the Boundary

Markers to prevent the Jet Bot from getting

in.

• Do not install the Clean Station in an area

with a dark floor.

- If the floor around the Clean Station is

dark, recharging is hindered.

• Move any obstacles that may disturb the

Jet Bot’s movement (such as children’s

indoor swing or slides) before cleaning.

Safety information

English

English 13

• Do not use the Jet Bot in a place which

is narrower than its turning radius 0.5m

(1.6ft) or less.

• Before operating the Jet Bot, remove the

objects which could break such as glass, a

frame, a mirror, and porcelain items so that

the Jet Bot works without interruption.

• If a brush or a brush cover is not assembled

correctly, scratches may occur on the floor,

or product malfunction may occur.

• Use both hands to carry the product.

• Do not place the Clean Station in a place

where people pass by frequently, in

entrance way or narrow passage.

- People may trip over it and be injured, or

product damage may occur.

• Do not push the Clean Station.

In use

WARNING

• If any abnormal sounds, smells or smoke

come from the Jet Bot, immediately shut off

the power switch of the Jet Bot and contact

a service center.

CAUTION

• Using the Jet Bot on a thick carpet may

damage both the Jet Bot and the carpet.

- The Jet Bot cannot pass over a carpet with

fiber longer than 2 cm.

• Do not use the Jet Bot on tables or other

high surfaces.

- There is a risk of damage if it falls.

• The Jet Bot may bump into chairs or desk

legs, therefore move them away for faster

and efficient cleaning.

• When the Jet Bot is operating, do not lift it

up or carry it to another area.

• Do not hold by Driving Wheels of the Jet

Bot when carrying it to another area.

• Do not put any objects on top of the Jet Bot

since it may cause malfunction of the LiDAR

sensor or the Jet Bot.

• Remove any large papers or plastic bags

immediately when using the Jet Bot since

they may block the intake.

• Do not lie down around the Jet Bot that is

running.

- Your hair may be caught in the brush,

resulting in physical injury.

• Do not allow children to play with the Jet

Bot.

• Make sure hair, fingers, clothes do not get

caught in a spin brush or Driving Wheels.

• Do not allow children to sit on the Jet Bot

and do not place an object on the Jet Bot.

• Leave over 3 cm space from the inner

doorstep placed in the entrance. Otherwise,

the robot vacuum can ride on it and go

outside.

Cleaning and maintenance

WARNING

• When the power cord is damaged, contact

a service center to get it replaced by a

certified repairman.

- There is a risk of fire or electric shock.

• Please check with a SAMSUNG Electronics

service center when replacing batteries.

- Using batteries from other products can

cause malfunction.

• Be careful not to put your finger into the

revolving LiDAR sensor. Otherwise, your

finger may get injured.

CAUTION

• Prevent any damage to the Jet Bot by

complying with the following.

- Do not clean the Jet Bot by spraying

water directly onto it or use a volatile

substance such as benzene, thinner, or

alcohol to clean it.

• Do not disassemble or repair the Jet Bot.

This should only be done by a certified

repairman.

Safety information

English

English14

Safety information

• Always keep the Obstacle Sensor Window

and the Cliff Sensor Window clear.

- If foreign matter accumulates, sensors

may malfunction.

• Do not store the Jet Bot in a car.

• Be careful that the LiDAR sensor is not

exposed to a direct light such as sun light,

infrared light, etc.

- The direct light can affect the performance

of the LiDAR sensor.

• When carrying the Jet Bot, be careful not to

let it drop.

- The impact from the drop can affect the

operation or performance of the LiDAR

sensor.

• Do not look at the transmitting part (a laser)

of the revolving LiDAR sensor horizontally.

• Be careful not to insert a tool such as a

chopstick into the revolving LiDAR sensor.

Otherwise, the LiDAR sensor may work

abnormally or malfunction.

• Before cleaning, remove objects which are

less than 9 cm height and are lightly on the

floor as the Jet Bot can push along them,

or the objects can be caught in the Jet

Bot’s Spin Brush or Driving Wheels. (Fixed

objects can be detected by the Jet Bot when

its bumper is pressed and will avoid them.)

• If oil such as cooking oil is on the floor, the

Jet Bot may become stationary because the

floor is slippery. Remove the oil first before

cleaning with the Jet Bot.

REGULATORY NOTICE

1. FCC Notice

WARNING

• Any changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s authority

to operate the equipment.

• This device complies with Part 15 of FCC

Rules. Operation is Subject to following two

conditions:

1

This device may not cause harmful

interference, and

2 This device must accept any interference

received including interference that cause

undesired operation.

• For product available in the USA/Canada

market, only channel 1~11 can be operated.

Selection of other channels is not possible.

FCC STATEMENT:

• This equipment has been tested and found

to comply within the limits for a Class B

digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation.

• This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there

is no guarantee that interference will not

occur in a particular installation. If this

equipment does cause harmful interference

to radio or television reception, which can

be determined by turning the equipment

off and on, the user is encouraged to try to

correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna

- Increase the separation between the

equipment and receiver

English

English 15

Safety information

- Connect the equipment into an outlet on

a different circuit from that to which the

receiver is connected

- Consult the dealer or an experienced

radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

• This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled

environment. This equipment should be

installed and operated with a minimum

distance of 20cm between the radiator and

your body. This device and its antenna(s)

must not be co-located or operation in

conjunction with any other antenna or

transmitter.

2. IC Notice

• The term “IC” before the radio certification

number only signifies that Industry Canada

technical specifications were met. Operation

is subject to the following two conditions: (1)

this device may not cause interference, and

(2) this device must accept any interference,

including interference that may cause

undesired operation of the device.

• This Class B digital apparatus complies with

Canadian ICES-003.

• Cet appareil numérique de la classe B est

conforme á la norme NMB-003 du Canada.

• For product available in the USA/Canada

market, only channel 1~11 can be operated.

Selection of other channels is not possible.

IC RADIATION EXPOSURE STATEMENT:

• This equipment complies with IC RSS-102

radiation exposure limits set forth for an

uncontrolled environment. This equipment

should be installed and operated with

minimum distance 20cm between the

radiator & your body. This device and

its antenna(s) must not be co-located or

operation in conjunction with any other

antenna or transmitter.

Open Source License Notice

• This device uses open source software.

Open Source Licenses are available on the

product menu.

• Tap “Settings > Network > Software Update

> Legal Information” on the device for more

details.

English

English16

Installation

NOTE

• If the cleaning area is wooden floors, it is

best to install the Clean Station along the

grain of wooden floors.

• If the power switch is off, the Jet Bot will

not charge even if it is docked on the Clean

Station.

• Always keep the Clean Station on.

- If power is not supplied to the Clean

Station, the Jet Bot cannot find it and

cannot automatically recharge.

- If the Jet Bot is left detached from the

Clean Station, the battery will drain

naturally.

• Do not attach the Boundary Markers as

(-----) shape.

- The Jet Bot may not detect it and cross

the boundary.

Charging

NOTE

• If the battery overheats during charging, it

may take longer to charge.

• When auto charging is not working, do the

following:

- Turn the power switch (at the side the Jet

Bot) off and on again.

- Unplug the Clean Station’s power plug and

then plug it back on.

- Unplug the Clean Station, and then check

whether there is any foreign matter on

the charging pins and clean charging pins

of the Jet Bot and the Clean Station with a

dry cloth or rag.

- Check for any obstacles such as reflective

objects, chairs, etc. near the Clean Station.

• If the Jet Bot is left detached from the Clean

Station, the battery will drain naturally.

- Try to keep the Jet Bot being charged on

the Clean Station. (However, turn off the

power switch and leave the Clean Station

unplugged when planning to leave the

house for long periods of time by going

on a business trip or vacation, etc.)

Using

NOTE

• The Jet Bot may get caught on thresholds

of entrance door or veranda, etc. during

cleaning.

- To restart operation, shut off the power

switch, move the Jet Bot to an area where

it can move easily, and then turn on the

power again.

• In a dark area, the Jet Bot may not

recognize an object.

- Before cleaning, remove obstacles on the

floor.

• The Jet Bot cannot completely clean areas

which it cannot enter, such as small space

between the corner, between the sofas or

walls, etc.

- Please use another cleaning tool to clean

them regularly.

• The Jet Bot cannot vacuum clumps of dirt,

so some may remain on the floor after

cleaning.

- Please use another cleaning tool to clean

them regularly.

• After turning the Jet Bot off, wait for a

while and then turn it on for a normal

rebooting.

• When the Clean Station smells, replace a

Dust Bag or clean filters.

• If there is a larva in the suctioned dust,

it can multiply in the Dust Bag. Clean the

Clean Station with a wet tissue and replace

the Dust Bag.

Notes and cautions

English

English 17

Cleaning and maintenance

NOTE

• If you washed the Dustbin and filter with

water

- Dustbin: Completely wipe out the water.

- Filter: Completely dry it in the shade

before use.

• Do not use water to clean the Fine dust

Filter, just shake it to clean.

• If suction power decreases continuously, or

the Jet Bot overheats, clean the Fine dust

Filter.

CAUTION

• Watch your fingers when attaching or

detaching the filter, since they may get

stuck in the Dustbin’s intake.

• To avoid blockages by foreign matter, do

not let the Jet Bot vacuum up toothpicks,

cotton swabs, etc.

• If it is difficult to remove foreign matter

from the brush, contact an authorized

SAMSUNG service center.

• Since the brush sweeps dirt up from the

floor during cleaning, foreign matter such

as a thin and long thread, long hair, etc.

may get caught in it. For the best cleaning

results, check and clean it regularly.

• Turn off the Jet Bot before cleaning or

maintenance work.

• If a brush or a brush cover is not assembled

correctly after the maintenance work,

scratches may occur on the floor, or product

malfunction may occur. Therefore, assemble

them correctly by checking the maintenance

method.

Battery usage

NOTE

• When you purchase a battery, check the

SAMSUNG logo ( ) attached on the

battery and the model name, then contact a

service center.

• This battery is exclusively for the SAMSUNG

Electronics Jet Bot. Do not use it for any

other products or purposes.

• Do not disassemble or modify the battery.

• Do not throw the battery out in fire or heat

it.

• Do not connect any metallic object to the

charging contacts (+,-).

• Store the battery indoors (at 0°C~40°C).

• If the battery malfunctions, do not

disassemble it yourself. Contact your

nearest SAMSUNG service center.

• As the battery is used over a length of time,

the battery charging time and usage time

decreases. In this case, contact a service

center and replace it with a new battery.

• Do not disassemble the battery yourself

and make sure short circuit of +, - poles

does not occur.

• When battery leak occurs, make sure it does

not touch your skin or eyes.

Notes and cautions

English

English18

The SmartThings App is only compatible with

models that have a Wi-Fi function.

If you do not have a Wi-Fi router, you cannot

use the SmartThings App.

Downloading the SmartThings App

• Download and install the SmartThings App

from the markets (Google Play Store, Apple

App Store, or SAMSUNG Galaxy Store). To

find the app, use the keyword “SmartThings”.

NOTE

• SmartThings is incompatible with some

tablets and some mobile devices.

• Some iPads and some mobile devices may

not be supported.

• Visit Play Store or App Store to see if

your mobile device is compatible with

SmartThings.

• The supporting software version of the

SmartThings app is subject to change

according to the OS supporting policy the

manufacturer provides. In addition, as

for the SmartThings app or the functions

that the app supports, the new application

update policy on the existing OS version

can be suspended due to usability or

security reasons.

• The SmartThings app is subject to change

without notice to improve usability

or performance. As the mobile phone

OS version is updated every year, the

SmartThings is also updated continually

according to the latest OS.

• If you have enquiries regarding the items

mentioned above, please contact us on

[email protected].

Setting up a SAMSUNG account

• You must sign in to a SAMSUNG account

before using the SmartThings App.

• To set up a SAMSUNG account, you can

follow the directions provided by the

SmartThings App.

• Or, if you have a SAMSUNG smartphone,

you can add your SAMSUNG account in the

setting app of your smartphone. Then, it

will automatically sign in to your SAMSUNG

account and you can use the SmartThings

App.

Registering a device to the SmartThings App

1 Connect your smartphone to your wireless

router.

- If the smartphone is not connected, turn

on the Wi-Fi in the Settings App and

select a wireless router you want to

connect to.

- Set your smartphone to use Wi-Fi only

and connect a device.

2 Launch the SmartThings App on your

smartphone.

3 If a pop-up saying that a new device has

been found appears, tap ADD NOW.

- If the pop-up does not appear, add a

device by selecting the ‘Home appliances’

category ‘Robot cleaner’ and the Jet

Bot to connect.

- If you scan the SmartThings QR code

attached on the Jet Bot, you can connect

to the Jet Bot more easily.

4 [Android] The connection to your device

will be progressed automatically.

- [iOS] Open the setting app, and select

[vacuum]_E30AJT** in the Wi-Fi list.

5 Provide the authentication when you are

directed to do so.

6 [Android] The connection to your wireless

router will be progressed automatically.

- [iOS] Open the setting app, and select the

wireless router in the Wi-Fi list.

7 When the product registration is complete,

the Jet Bot device card is added.

NOTE

• Setting Wi-Fi On/Off: Hold the [ ] button

down for 7 seconds to switch the Wi-Fi off

or on to use again while the vacuum cleaner

is on standby or charging.

SmartThings App

English

English 19

SmartThings App

Functions of the SmartThings App

Classification

Functions Explanation

Monitoring Cleaning Report • You can check the result of the last cleaning.

• You can check the histories of last 50 cleanings.

Control

Dock • You can stop cleaning and have the Jet Bot return to the

Clean Station.

Pause • You can stop cleaning or restart cleaning.

Cleaning Mode • You can set the cleaning mode you want.

Cleaning Functions

• You can set various cleaning functions.

- For some functions, you need to create a map first.

- For Room Clean and Spot Clean, you can choose only

one of them, and the default setting is ‘All’ (All Rooms).

When the Jet Bot is in the Room Clean or the Spot

Clean, it may pass an unselected area to go to the

cleaning place or to recharge.

Schedule • You can start designated cleaning at the scheduled time.

Setting

Sound Mode • You can set the voice guide to [Voice], [Sound Effect], or

[Mute].

Language • The Jet Bot supports 14 languages.

Volume • You can control the volume of the voice guide.

Downtime

• At the designated time, the Jet Bot stops cleaning and

returns to the Clean Station.

- You may start cleaning during Downtime.

Find Robot Vacuum • The Jet Bot makes a sound so that a user can find it.

Child Lock

• The Jet Bot locks its buttons so that they do not function.

To unlock the buttons, turn the Jet Bot off and then on

again.

Empty Dust

• You can select when to empty the dustbin of the Jet Bot.

Notice Cleaning completed • When cleaning is complete, you can receive cleaning

completion notice.

Check Notice

• If the Jet Bot needs to be checked, you can receive a notice.

Manage

maps

No-go Zones

• You can set a zone where you do not want the Jet Bot to

clean.

- You can create maximum 15 zones.

Edit Map • You can divide or combine rooms on the created map.

• You can change the name of a room.

Reset Map • Reset the saved map.

English

English20

Troubleshooting

Symptom Checklist

The Jet Bot is not

working at all.

• Check if the power switch is on.

• Check if the Status Indicator is on.

• Check if the Jet Bot’s battery is depleted.

- When the Jet Bot’s Status Indicator turns red and stays red, place

the Jet Bot manually on the Clean Station to charge it.

• When you manually charge the Jet Bot due to complete discharge of

its battery, the buttons on the Jet Bot do not work. When charging is

partially complete (about 10-20 minutes later), the Status Indicator is

on and the buttons work again.

The Jet Bot has

stopped during

cleaning.

• When the Jet Bot’s Status Indicator turns red and stays red, place the

Jet Bot manually on the Clean Station to charge it.

• When the Jet Bot is immobilized by an obstacle such as a cord,

obstacles, threshold, a raised spot, etc., pick it up and move it away

from the obstacle.

- If any fabric or string is caught in a Driving Wheel, turn off the

power switch and remove the fabric or string before using it again.

• Check whether the No-go Zones are set.

Suction power is

weak.

• When there’s too much dust in the Dustbin, suction power may get

weakened. Turn off the power switch and empty the Dustbin.

• If the brush at the bottom of the Jet Bot is blocked by foreign matter,

turn off the power switch and remove foreign matter from the brush.

• When noise suddenly increases, turn off the power switch and empty

the Dustbin.

The Jet Bot cannot

find the Clean Station.

• Check if there’s a power failure or whether the power plug is

unplugged.

• Remove any obstacles around the Clean Station that may prevent the

Jet Bot from returning to the Clean Station.

• When there’s foreign matter on the charging terminals, charging can

be affected. Clean the foreign matter off the terminals.

The Jet Bot does not

detect the Boundary

Marker and crosses

the boundary.

• Make sure the Boundary Markers are attached as ( ) shape at 15

cm before the locations where the Jet Bot should not cross.

La page charge ...

Samsung NK36K7000WG Manuel utilisateur

Ce manuel convient également à

Samsung NK36K7000WG Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents