Modern Forms WS-96318 Ezra Mode d'emploi

Taper
Mode d'emploi
1
INSTALLATION INSTRUCTIONS

WS-96318


Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760

To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
Read all instructions before installing.
System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
Lisez toutes les instructions avant l’installation.
Le système doit être installé par un électricien licensié conformément au code national de lélectricité (NEC), et également aux
règlements locaux.
Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire connector
Qty: 3PCS+1Extra
Mounting screw
Qty: 1Extra
ABB
2
INSTALLATION INSTRUCTIONS

WS-96318


Black or
Smooth

White or
Ribbed

Bare wire
(Ground)

Black
(Hot)

White
(Neutral)

Green or Bare Copper
(Ground)



Phone (800) 526.2588
Fax (800) 526.2585

44 Harbor Park Drive
Port Washington, NY 11050

1600 Distribution Ct
Lithia Springs, GA 30122

1750 Archibald Avenue
Ontario, CA 91760

1. Shut off the power at the circuit breaker and
remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.

Secure the mounting plate to the junction box using standard junction box screws
that comes with the junction box.
Note: (i) Using any other non-original-manufacturer provided junction box screw
may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.

4. Connect the driver’s input wires to junction box wires as shown in
Fig. 2, making sure that all wire connectors (A) are secured. If your outlet
box has a green or bare copper ground wire, connect the xtures
ground wire to it. Otherwise, connect the xtures ground wire directly
to the back plate using the GND screw provided. After wires are connected,
tuck them carefully inside the junction box.
5. Secure the xture to the mounting plate using the mounting screw (B) .
1 1/2"
1 3/4"
Ø4 3/4"

Junction box
Junction box screw
Mounting plate
Mounting screw
Fixture
Wire connector
A
B
Driver
  • Page 1 1
  • Page 2 2

Modern Forms WS-96318 Ezra Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues