Lumination Elementaire Series HTEK-TEK Guide d'installation

Marque: Lumination

Modèle: Elementaire Series HTEK-TEK

Taper: Guide d'installation

LED.com

speciﬁcations subject to change without notice. All values are design or typical values

when measured under laboratory conditions.

Page 1 of 3

(Rev 4/19/23)

IND314-Lumination-LEL-Series-HTEK-TEK-Mounting-Installation-Guide_R01

Installation Guide

IND314

Lumination® LED Luminaire

HTEK/TEK Mounting

(LEL Series)

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Wear work gloves to prevent dirt and oil from being transferred to the luminaire.

WARNING / AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC or IEC local codes.

RISK OF INJURY

• Luminaire may fall down if not locked into mounting

track properly.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation

électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC ou IEC ainsi que les et codes locaux

applicables.

RISK OF INJURY

• Le luminaire pourrait tomber s’il n’est pas verrouiillé en place

correctement aux rails de montage.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

LED.com

speciﬁcations subject to change without notice. All values are design or typical values

when measured under laboratory conditions.

Page 2 of 3

(Rev 4/19/23)

IND314-Lumination-LEL-Series-HTEK-TEK-Mounting-Installation-Guide_R01

Lumination® (LEL - Series) Installation Guide

Installation

Unpack unit from packaging. Properly inspect for defects

before installing.

RISK OF DAMAGE: Make sure the luminaire is only

carried out by holding two ends of gear box. Do

not touch the light guide when removing the xture

from the packaging or during the installation.

Track

Gearbox

Light guide

Dummy

adapter

Adapter with

metal pin

CAUTION / ATTENTION

RISK OF DAMAGE

• Remove protective lm on Light Guide after installation.

• Do not touch Light Guide to avoid dirt, oil and ngerprints.

RISQUE DE DOMMAGES

• Retirez le lm protecteur du luminaire après son installation.

• Ne touchez pas la surface émittrice du luminiaire pour éviter

les saletés, graisses ou empreintes digitales.

Ensure alignment lines on luminaire and adaptors are parallel

and insert xture vertically into track.

Track

Gearbox

Light guide

Dummy

adapter

Adapter with

metal pin

(A) On both adapters, rotate mechanical xing knob clockwise to ON position to lock xture to track.

(B) On adapter with metal pin on top, select the desired circuit with the circuit selector knob.

(C) For the dummy adapter without the metal pin, need to turn mechanical xing knob clockwise to the cavity stopper as shown above.

CAUTION: Must turn mechanical xing knobs to the right position to prevent the luminaire from falling off without locking.

Track

Lock Lock

OFF

1 2

Mechanical Circuit

selector knob

Cavity stopper

Dummy adapter

LED.com

speciﬁcations subject to change without notice. All values are design or typical values

when measured under laboratory conditions.

Page 3 of 3

(Rev 4/19/23)

IND314-Lumination-LEL-Series-HTEK-TEK-Mounting-Installation-Guide_R01

Lumination® (LEL - Series) Installation Guide

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A)

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Luminaire Removal

To remove xture put Circuit Selector to 0 and Mechanical Knob to off. Then, while tilting xture, remove luminaire marked side rst. Carefully check

the clips are still in the right positions after removing the protective lm. If the clips fall down, need push them back to the right positions.

Clips

Put the inter-connector on the top of two luminaires, and

make sure that the slot of the inter-connector crosses the two

end caps.

Inter-connector

Light Guide Clip

Push the inter-connector into the luminaires.

Remove the protective lm, and insert the Light