Makita UR014G Manuel utilisateur

UR014G

EN Cordless Grass Trimmer INSTRUCTION MANUAL 8

FR Coupe Herbe Sans Fil MANUEL D’INSTRUCTIONS 19

DE Akku-Rasentrimmer BETRIEBSANLEITUNG 32

IT Tagliabordi a batteria ISTRUZIONI PER L’USO 45

NL Accugrastrimmer GEBRUIKSAANWIJZING 58

ES Cortador Inalámbrico de

Pasto

MANUAL DE

INSTRUCCIONES 71

PT TESOURA PARA GRAMA A

BATERIA MANUAL DE INSTRUÇÕES 84

DA Akku græstrimmer BRUGSANVISNING 97

EL   109

TR  KULLANMA KILAVUZU 122

2

Fig.1

12

43

5

6

14

13

12

7

8

9

10

11

Fig.2

3

1 1

2

3

Fig.3

1

2

Fig.4

2

1

Fig.5

2

1

Fig.6

1

Fig.7

2

1

Fig.8

4

2

1

Fig.9

1

2

3

45

Fig.10

1

Fig.11

1

2

Fig.12

1

2

Fig.13

1

2

3

Fig.14

5

1

2

3

Fig.15

1

2

3

4

Fig.16

1

2

3

Fig.17

1

2

3

Fig.18

Fig.19

1

Fig.20

Fig.21

6

1

Fig.22

7

1

2

4

3

5

6

3 m (9 ft)

100 mm

(3-15/16″)

Fig.23

8ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: UR014G

Handle type Loop handle

No load speed 0 - 5,000 min-1

Overall length

(without cutting tool and battery)

1,857 mm

Nylon cord diameter 2.7 mm

Applicable cutting tool and

cutting diameter

Nylon cutting head

(P/N 1911Y3-7)

450 mm

Rated voltage D.C. 36 V - 40 V max

Net weight 5.5 - 6.7 kg

Protection degree IPX4

•



 

 -

est combinations, according to EPTA-Procedure 01/2014, are shown in the table.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040 / BL4050F* / BL4080F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

•

Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges



Recommended cord connected power source

Portable power pack PDC01 / PDC1200

• The cord connected power source(s) listed above may not be available depending on your region of residence.

• Before using the cord connected power source, read instruction and cautionary markings on them.

Noise

Applicable standard : ISO22868(ISO11806-1)/EN50636-2-91

Cutting tool

Sound pressure level (LpA) dB(A)

Sound power level (LWA) dB(A)

LpA dB(A)

Uncertainty (K)

dB(A)

LWA dB(A)

Uncertainty (K)

dB(A)

Nylon cutting head 77.9 2.9 91.3 1.9

• Even if the sound pressure level listed above is 80 dB (A) or less, the level under working may exceed 80 dB

(A). Wear ear protection.

NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING: -

ue(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the



9ENGLISH

Vibration

Applicable standard : ISO22867(ISO11806-1)

Cutting tool Left hand Right hand

ah,W (m/s2)Uncertainty K

(m/s2)

ah,W (m/s2)Uncertainty K

(m/s2)

Nylon cutting head 2.5 1.5 2.5 1.5

NOTE: The declared vibration total value(s) has been measured in accordance with a standard test method and

may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also be used in a preliminary assessment of exposure.

WARNING: 

value(s) depending on the ways in which the tool is used especially what kind of workpiece is processed.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation

of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the



Symbols

The followings show the symbols which may be used

for the equipment. Be sure that you understand their

meaning before use.

Take particular care and attention.

Read instruction manual.

Wear eye and ear protection.

15m(50FT)Keep distance at least 15 m.



Warning; Disconnect battery before

maintenance.

Never use metal and plastic blade.

Ni-MH

Li-ion

Only for EU countries

Due to the presence of hazardous com-

ponents in the equipment, waste electrical

and electronic equipment, accumulators

and batteries may have a negative impact

on the environment and human health.

Do not dispose of electrical and electronic

appliances or batteries with household

waste!

In accordance with the European Directive

on waste electrical and electronic equip-

ment and on accumulators and batteries

and waste accumulators and batteries,

as well as their adaptation to national law,

waste electrical equipment, batteries and

accumulators should be stored separately

and delivered to a separate collection point

for municipal waste, operating in accor-

dance with the regulations on environmen-

tal protection.

This is indicated by the symbol of the

crossed-out wheeled bin placed on the

equipment.

Guaranteed sound power level according

to EU Outdoor Noise Directive.

Sound power level according to Australia

NSW Noise Control Regulation.

Declarations of Conformity

For European countries only

The Declarations of conformity are included in Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING Read all safety warnings, instruc-



this power tool. Failure to follow all instructions listed





Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Important safety instructions for the

tool

WARNING: Read all safety warnings and

all instructions. Failure to follow the warnings and





10 ENGLISH

Save all warnings and instruc-

tions for future reference.

Intended use

1. This tool is only intended for cutting grass,

weeds, bushes and undergrowth. It should not

be used for any other purpose such as edging

or hedge cutting as this may cause injury.

General instructions

1. Never allow people unfamiliar with these

instructions, people (including children) with

reduced physical, sensory or mental capabil-

ities, or lack of experience and knowledge to

use the tool. Children should be supervised to

ensure that they do not play with the tool.

2.

Before starting the tool, read this instruction man-

ual to become familiar with the handling of the tool.

3. -

cient experience or knowledge regarding han-

dling of brushcutters and string trimmers.

4. When lending the tool, always attach this

instruction manual.

5.

Handle the tool with the utmost care and attention.

6. Never use the tool after consuming alcohol or

drugs, or if feeling tired or ill.

7. Never attempt to modify the tool.

8.

Follow the regulations about handling of brush-

cutters and string trimmers in your country.

Personal protective equipment

Fig.1

1. Wear safety helmet, protective goggles and

protective gloves to protect yourself from



2. -

vent hearing loss.

3. Wear proper clothing and shoes for safe

operation, such as a work overall and sturdy,

non-slip shoes. Do not wear loose clothing or

jewelry.

caught in moving parts.

4. When touching the cutting tool, wear protec-

tive gloves.

Work area safety

1. Operate the tool under good visibility and day-

light conditions only. Do not operate the tool in

darkness or fog.

2. Do not operate the tool in explosive atmo-



liquids, gases or dust. The tool creates sparks

which may ignite the dust or fumes.

3. During operation, never stand on an unstable

or slippery surface or a steep slope. During

the cold season, beware of ice and snow and

always ensure secure footing.

4. During operation, keep bystanders or animals

at least 15 m away from the tool. Stop the tool

as soon as someone approaches.

5. Never operate the tool while people, especially

children, or pets are nearby.

6.

Before operation, examine the work area for

stones or other solid objects. They can be thrown



7. WARNING: Use of this product can create

dust containing chemicals which may cause

respiratory or other illnesses. Some examples

of these chemicals are compounds found in

pesticides, insecticides, fertilizers and herbi-

cides. Your risk from these exposures varies,

depending on how often you do this type

of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed



Electrical and battery safety

1. Do not expose the tool to rain or wet condi-

tions. Water entering the tool will increase the risk

of electric shock.

2. Do not use the tool if the switch does not

 Any tool that cannot be con-

trolled with the switch is dangerous and must be

repaired.

3. Prevent unintentional starting. Ensure the



battery pack, picking up or carrying the tool.



energising the tool that have the switch on invites

accidents.

4. 

The cell may explode. Check with local codes for

possible special disposal instructions.

5. Do not open or mutilate the battery(ies).

Released electrolyte is corrosive and may cause

damage to the eyes or skin. It may be toxic if

swallowed.

6.

Do not charge battery in rain, or in wet locations.

7. Avoid dangerous environment. Don't use the

tool in dump or wet locations or expose it to

rain. Water entering the tool will increase the risk

of electric shock.

8. Do not charge the battery outdoors.

9. Do not handle charger, including charger plug,

and charger terminals with wet hands.

10. Do not replace the battery with wet hands.

11. Do not replace the battery in the rain.

12. Do not wet the terminal of battery with liquid

such as water, or submerge the battery. Do not

leave the battery in the rain, nor charge, use,

or store the battery in a damp or wet place. If

the terminal gets wet or liquid enters inside of bat-

tery, the battery may be short circuited and there is



13. After removing the battery from the tool or

charger, be sure to attach the battery cover to

the battery and store it in a dry place.

14. If the battery cartridge gets wet, drain the

water inside and then wipe it with a dry cloth.

Dry the battery cartridge completely in a dry

place before use.

15. When you use the tool on muddy ground, wet

slope, or slippery place, pay attention to your

footing.

11 ENGLISH

Putting into operation

1. Before assembling or adjusting the tool,

remove the battery cartridge.

2. Before handling the cutting tool, wear protec-

tive gloves.

3. Before installing the battery cartridge, inspect

the tool for damages, loose screws/nuts or

improper assembly. If the cutting tool is bent

or damaged, replace it. Check all control levers

and switches for easy action. Clean and dry

the handles.

4. Never attempt to switch on the tool if it is dam-

aged or not fully assembled. Otherwise serious



5. Adjust the shoulder harness Adjust the

hand grip to suit the operator's body size if

adjustable.

6. When inserting a battery cartridge, keep the

cutting attachment clear of your body and

other object, including the ground. It may rotate



the tool and/or property.

7. Remove any adjusting key, wrench before

turning the tool on. An accessory left attached

to a rotating part of the tool may result in personal



8. The cutting tool has to be equipped with the

guard. Never run the tool with damaged guards

or without guards in place!

9. Make sure there are no electrical cables, water

pipes, gas pipes etc. that could cause a hazard

if damaged by use of the tool.

Operation

1. 

tool immediately.

2. If you feel any unusual condition (e.g. noise,



tool and remove the battery cartridge. Do not

use the tool until the cause is recognized and

solved.

3. The cutting attachment continues to rotate for



rush to contact the cutting attachment.

4. During operation, use the shoulder harness if

supplied with the tool. Keep the tool on your



5. Do not overreach. Keep proper footing and

balance at all times. Watch for hidden obsta-

cles such as tree stumps, roots and ditches to

avoid stumbling.

6. Always be sure of your footing on slopes.

7. Walk, never run.

8. Never work on a ladder or tree to avoid loss of

control.

9. If the tool gets heavy impact or fall, check the

condition before continuing work. Check the

controls and safety devices for malfunction. If

there is any damage or doubt, ask our autho-

rized service center for the inspection and

repair.

10. Do not touch the gear case during and imme-

diately after the operation. The gear case

becomes hot during operation and can cause burn



11. Take a rest to prevent loss of control caused

by fatigue. We recommend taking a 10 to 20-min-

ute rest every hour.

12. When you leave the tool, even if it is a short

time, always remove the battery cartridge. The

unattended tool with the battery cartridge installed

may be used by unauthorized person and cause

serious accident.

13. If grass or branches get caught between the

cutting attachment and guard, always turn



before cleaning. Otherwise the cutting attach-

ment may rotate unintentionally and cause serious



14. Never touch moving hazardous parts before

the moving hazardous parts have come to

a complete stop and the battery cartridge is

removed.

15. If the cutting attachment hits stones or other



Then remove the battery cartridge and inspect

the cutting attachment.

16. Check the cutting attachment frequently

during operation for cracks or damages.

Before the inspection, remove the battery

cartridge and wait until the cutting attachment

stops completely. Replace damaged cutting

attachment immediately, even if it has only



17. Never cut above waist height.

18. Before starting the cutting operation, wait until

the cutting attachment reaches a constant

speed after turning the tool on.

19. When using a cutting tool, swing the tool

evenly in half-circle from right to left, like

using a scythe.

20. Hold the tool by insulated gripping surfaces

only, because the cutting tool may contact

hidden wiring. Cutting tool contacting a "live" wire

may make exposed metal parts of the tool "live"

and could give the operator an electric shock.

21. Do not start the tool when the cutting tool is

tangled with cut grass.

22. Before starting the tool, be sure that the cut-

ting tool is not touching the ground and other

obstacles such as a tree.

23. During operation always hold the tool with

both hands. Never hold the tool with one hand

during use.

24. Do not operate the tool in bad weather or if

there is a risk of lightning.

25. When you use the tool on muddy ground, wet

slope, or slippery place, pay attention to your

footing.

26. Avoid working in poor environment where

increased user fatigue is expected.

27. Do not use the tool in bad weather where visi-

bility is limited. Failure to do so may cause fall or

incorrect operation due to low visibility.

28. Do not submerge the tool into a puddle.

12 ENGLISH

29. Do not leave the tool unattended outdoors in

the rain.

30. When wet leaves or dirt adhere to the suc-

tion mouth (ventilation window) due to rain,

remove them.

31. Do not use the tool in the snow.

Cutting tools

1. Do not use a cutting tool which is not recom-

mended by us.

2. Use an applicable cutting attachment for the

job in hand.

— Nylon cutting heads (string trimmer heads)

are suitable for trimming lawn grass.

— Never use other blades including metal





3. Only use the cutting tool that are marked with

a speed equal or higher than the speed marked

on the tool.

4. Always keep your hands, face, and clothes

away from the cutting tool when it is rotating.



5. Always use the cutting attachment guard prop-

erly suited for the cutting attachment used.

Vibration

1. People with poor circulation who are exposed

to excessive vibration may experience injury

to blood vessels or the nervous system.

Vibration may cause the following symptoms



asleep" (numbness), tingling, pain, stabbing sen-

sation, alteration of skin color or of the skin. If any

of these symptoms occur, see a physician!

2. 

keep your hands warm during operation and

well maintain the tool and accessories.

Transport

1. 

remove the battery cartridge.

2. When transporting the tool, carry it in a hori-

zontal position by holding the shaft.

3. When transporting the tool in a vehicle, prop-

erly secure it to avoid turnover. Otherwise

damage to the tool and other baggage may result.

Maintenance

1. Have your tool serviced by our authorized

service center, always using only genuine

replacement parts. Incorrect repair and poor

maintenance can shorten the life of the tool and

increase the risk of accidents.

2. Before doing any maintenance or repair work



remove the battery cartridge.

3. Always wear protective gloves when handling

the cutting tool.

4. 

use gasoline, benzine, thinner, alcohol or the

like for the purpose. Discoloration, deformation

or cracks of the plastic components may result.

5. After each use, tighten all screws and nuts.

6. Do not attempt any maintenance or repair not

described in the instruction manual. Ask our

authorized service center for such work.

7. Always use our genuine spare parts and

accessories only. Using parts or accessories

supplied by a third party may result in the tool

breakdown, property damage and/or serious



8. Request our authorized service center to

inspect and maintain the tool at regular

interval.

9. Always keep the tool in good working condi-

tion. Poor maintenance can result in inferior per-

formance and shorten the life of the tool.

10. Keep handles dry, clean and free from oil and

grease. Keep all cooling air inlets clear of

debris.

11. Do not wash the tool with high pressure water.

12. When washing the tool, do not let water enter

the electrical mechanism such as battery,

motor, and terminals.

13. When storing the tool, avoid direct sunlight

and rain, and store it in a place where it does

not get hot or humid.

14. Perform inspection or maintenance in a place

where rain can be avoided.

15. After using the tool, remove the adhered dirt

and dry the tool completely before storing.

Depending on the season or the area, there is a

risk of malfunction due to freezing.

Storage

1. Before storing the tool, perform full clean-

ing and maintenance. Remove the battery

cartridge.

2. Store the tool in a dry and high or locked loca-

tion out of reach of children.

3. Do not prop the tool against something, such

as a wall. Otherwise it may fall suddenly and



First aid

1. 

Immediately replace any item taken from the



2. When asking for help, give the following

information:

— Place of the accident

— What happened

 

 

— Your name

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

13 ENGLISH

Important safety instructions for

battery cartridge

1.

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

2. Do not disassemble or tamper with the battery

cartridge.

or explosion.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current



breakdown.

6. Do not store and use the tool and battery car-

tridge in locations where the temperature may

reach or exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn



8. Do not nail, cut, crush, throw, drop the battery

cartridge, or hit against a hard object to the

battery cartridge. Such conduct may result in a



9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.



battery in such a manner that it cannot move

around in the packaging.

11. When disposing the battery cartridge, remove

it from the tool and dispose of it in a safe

place. Follow your local regulations relating to

disposal of battery.

12. Use the batteries only with the products

 Installing the batteries to

-

sive heat, explosion, or leak of electrolyte.

13. If the tool is not used for a long period of time,

the battery must be removed from the tool.

14. During and after use, the battery cartridge may

take on heat which can cause burns or low

temperature burns. Pay attention to the han-

dling of hot battery cartridges.

15. Do not touch the terminal of the tool imme-

diately after use as it may get hot enough to

cause burns.

16. Do not allow chips, dust, or soil stuck into the

terminals, holes, and grooves of the battery

cartridge.

burst and malfunction of the tool or battery car-



17. Unless the tool supports the use near

high-voltage electrical power lines, do not use

the battery cartridge near high-voltage electri-

cal power lines. It may result in a malfunction or

breakdown of the tool or battery cartridge.

18. Keep the battery away from children.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting



also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1.

Charge the battery cartridge before completely dis-

charged. Always stop tool operation and charge the

battery cartridge when you notice less tool power.

2.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3.

Charge the battery cartridge with room tempera-

ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot

battery cartridge cool down before charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

PARTS DESCRIPTION

Fig.2

1High-torque lamp 2Reverse lamp 3Caution lamp 4Main power lamp

5

Reverse / high-torque button

6Main power button 7Battery cartridge 8Switch trigger

9Hanger 10 Handle 11 Protector 12 

13  14 Shoulder harness ----

14 ENGLISH

FUNCTIONAL

DESCRIPTION

WARNING: Always be sure that the tool is



before adjusting or checking function on the tool.





start-up.

Installing or removing battery

cartridge

CAUTION: 

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-



cartridge. Failure to hold the tool and the battery



and result in damage to the tool and battery cartridge



Fig.3: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator as



CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,



you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection



the motor to extend tool and battery life. The tool will

automatically stop during operation if the tool is placed

under one of the following conditions:

Caution lamp Status

Color On Blinking

Green Overload

Red (tool) / (battery) Overheat

Red Over

discharge

Overload protection

If the tool gets into one of the following situation, the

tool automatically stops and the caution lamp starts

blinking in green:

— The tool is overloaded by entangled weeds or

other debris.

— The cutting tool is locked.

— The main power button is turned on while the

switch trigger is being pulled.

In this situation, release the switch trigger and remove

entangled weeds or debris if necessary. After that, pull

the switch trigger again to resume.

CAUTION: If you need to remove the entan-

gled weeds on the tool or release the locked



start.

Overheat protection for tool or

battery

If the tool or battery cartridge is overheated, the tool

stops automatically. When the tool is overheated, the

caution lamp lights up in red. When the battery cartridge

is overheated, the caution lamp blinks in red. Let the

tool and/or battery cool down before turning the tool on

again.

Overdischarge protection

When the battery capacity becomes low, the tool stops

automatically and the caution lamp starts blinking in red.

If the tool does not operate even when the switches are

operated, remove the battery cartridge from the tool and

charge it.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Fig.4: 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted  Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

15 ENGLISH

NOTE: Depending on the conditions of use and the



from the actual capacity.

NOTE:

the battery protection system works.

Main power switch

To turn on the tool, press the main power button. To turn





Fig.5: 1. Main power lamp 2. Main power button

NOTE:

without any operations for a certain period of time.

Switch action

WARNING: For your safety, this tool is



tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger



tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-



CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released. Operating a tool

with a switch that does not actuate properly can lead



CAUTION: 

power button and switch trigger when carrying

the tool. The tool may start unintentionally and cause



NOTICE: Do not pull the switch trigger hard with-



switch breakage.

To prevent the switch trigger from being accidentally





Release the switch trigger to stop.

Fig.6: 1.2. Switch trigger

Speed adjusting



-



increase the speed, move the lever toward you. To

decrease the speed, move the lever forward. When the



stops.

Fig.7: 1.

Reverse button

WARNING: 

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation

function can not remove.

remove the battery cartridge may result in serious



This tool has the reverse button to change the direction

of rotation. By changing the direction of rotation, you



The reverse button is also used for removing weeds

and debris entangled in the tool.

To reverse the rotation, press the reverse / high-torque

button when the cutting tool is stopped. The reverse

lamp lights up. The cutting tool rotates in reverse direc-

tion when you pull the switch trigger while depressing



To return to regular rotation, press the reverse / high-

torque button when the cutting tool is stopped.

Fig.8: 1. Reverse lamp 2. Reverse / high-torque

button

NOTE: If you press the reverse / high-torque button

while the cutting tool is still rotating, the tool comes to

stop and to be ready for reverse rotation.

High-torque button

You can use the tool in the high-torque mode. In the

high-torque mode, the tool speed is less likely to

decrease than in the normal mode when the load of the

tool is large.

To use the tool in the high-torque mode, press and hold

the reverse / high-torque button. The high-torque lamp

lights up. To return to the normal mode, press and hold

the reverse / high-torque button again.

Fig.9: 1. High-torque lamp 2. Reverse / high-torque

button

Electric brake

This tool is equipped with an electric brake. If the tool

consistently fails to quickly stop after the switch trigger

is released, have the tool serviced at our service center.

CAUTION: This brake system is not a substi-

tute for the protector. Never use the tool without

the protector. An unguarded cutting tool may result



Electronic function

Constant speed control

The speed control function provides the constant rota-

tion speed regardless of load conditions.

Soft start feature

Soft start because of suppressed starting shock.

16 ENGLISH

ASSEMBLY

WARNING: Always be sure that the tool is



before carrying out any work on the tool. Failure to





WARNING: Never start the tool unless it is

completely assembled. Operation of the tool in a

partially assembled state may result in serious per-



Installing the handle

1. Attach the upper and lower clamps on the damper.

2. 

hex socket head bolts as illustrated.

Fig.10: 1. Hex socket head bolt 2. Handle 3. Upper

clamp 4. Damper 5. Lower clamp

Hex wrench storage

CAUTION: Be careful not to leave the hex

wrench inserted in the tool head. It may cause



When not in use, store the hex wrench as illustrated to

keep it from being lost.

Fig.11: 1. Hex wrench

Installing the cutting tool

CAUTION: Always use the supplied wrenches

to remove or to install the cutting tool.

CAUTION: Be sure to remove the hex wrench

inserted into the tool head after installing the

cutting tool.

NOTE: The type of the cutting tool(s) supplied as

the standard accessory varies depending on the

countries. The cutting tool is not included in some

countries.

NOTE: Turn the tool upside down so that you can

replace the cutting tool easily.

Nylon cutting head

NOTICE: Be sure to use genuine Makita nylon

cutting head.

1. Insert the hex wrench through the hole in the gear

case to lock the spindle. Rotate the spindle until the hex

wrench is fully inserted. Remove the nut by turning it

clockwise with the box wrench.

Fig.12: 1. Nut 2. Hex wrench

2. Remove the spool holder by pressing the claws.

Fig.13: 1. Spool holder 2. Claw

3.

Remove the spool from the spool holder by holding



both sides of the nylon cord to the notches of the spool.

Fig.14: 1. Spool 2. Spool holder 3. Notch

4. Insert the hex wrench through the hole in the gear

case to lock the spindle. Attach the spool holder to the

spindle, and then tighten the nut by turning it counter-

clockwise with the box wrench.

Fig.15: 1. Nut 2. Spool holder 3. Hex wrench

NOTE: The recommended tightening torque is 20 to

30 N•m.

5. Attach the spool to the spool holder, and then set

both sides of the nylon cord to the eyelets of the spool

holder. Attach the spool cover to the spool holder.

Fig.16: 1. Spool 2. Spool holder 3. Eyelet 4. Spool

cover

6. Remove the hex wrench from the gear case.

Correct combination of the cutting

tool and the protector

CAUTION: Always use the correct combi-

nation of cutting tool and the protector. A wrong

combination may not protect you from the cutting tool,

-



Cutting tool Protector

Nylon cutting head

Installing the protector

WARNING: Never use the tool without the

guard illustrated in place. Failure to do so can



CAUTION: Take care not to injure yourself on

the cutter for cutting the nylon cord.

Attach the protector to the clamp using bolts.

Fig.17: 1. Clamp 2. Protector 3. Cutter

OPERATION

Attaching the shoulder harness

WARNING: Be extremely careful to maintain

control of the tool at all times. Do not allow the



work vicinity. Failure to keep control of the tool



operator.

17 ENGLISH

CAUTION: Always use the shoulder harness

attached to the tool. Before operation, adjust the

shoulder harness according to the user size to

prevent fatigue.

CAUTION: Before operation, make sure that

the shoulder harness is properly attached to the

hanger on the tool.

CAUTION: When you use the tool in combi-

nation of the backpack-type power supply such

as portable power pack, do not use the shoulder

harness included in the tool package, but use the

hanging band recommended by Makita.

If you put on the shoulder harness included in the

tool package and the shoulder harness of the back-

pack-type power supply at the same time, removing



case of an emergency, and it may cause an accident



Makita Authorized Service Centers.

1. Clasp the hook on the shoulder harness to tool's

ring and hanger.

Fig.18: 1. Ring 2. Hook 3. Hanger

2. Put on the shoulder harness on your left shoulder.



position.

Fig.19

The shoulder harness features a means of quick

release. Simply squeeze the sides of the buckle while

holding the tool to release the tool from the shoulder

harness.

Fig.20: 1. Buckle

Correct handling of the tool

WARNING: Always position the tool on your

right-hand side. Correct positioning of the tool allows

for maximum control and will reduce the risk of seri-



WARNING: Be extremely careful to maintain

control of the tool at all times. Do not allow the



work vicinity. Failure to keep control of the tool



operator.

WARNING: To avoid accident, leave more

than 15m (50 ft) distance between operators when

two or more operators work in one area. Also,

arrange a person to observe the distance between

operators. If someone or an animal enters the

working area, immediately stop the operation.

CAUTION: If the cutting tool accidentally

impacts a rock or hard object during operation,

stop the tool and inspect for any damage. If the

cutting tool is damaged, replace it immediately.

Use of a damaged cutting tool may result in serious



Correct positioning and handling allow optimum control



Fig.21

When using a nylon cutting head (bump & feed

type)

The nylon cutting head is a dual string trimmer head

provided with a bump & feed mechanism.

To feed out the nylon cord, tap the cutting head against

the ground while rotating.

Fig.22: 1.

NOTICE: The bump feed will not operate prop-

erly if the nylon cutting head is not rotating.

NOTE: If the nylon cord does not feed out while

tapping the head, rewind/replace the nylon cord

by following the procedures in the section for the

maintenance.

MAINTENANCE

WARNING: Always be sure that the tool is



before attempting to perform inspection or main-

tenance on the tool.

the battery cartridge may result in serious personal



NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,



be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Cleaning the tool



with a dry cloth or one dipped in soapy water and wrung

out. To avoid overheating of the tool, be sure to remove



tool.

Replacing the nylon cord

WARNING: Use only the nylon cord with



Never use heavier line, metal wire, rope or the

like. Failure to do so may cause damage to the tool



WARNING: Always remove the nylon cutting

head from the tool when replacing the nylon cord.

WARNING: Make sure that the cover of the

nylon cutting head is secured to the housing

properly as described below. Failure to properly

secure the cover may cause the nylon cutting head to



Replace the nylon cord if it is not fed any more. The

method of replacing the nylon cord varies depending on

the type of the nylon cutting head.

121-SP

Fig.23

18 ENGLISH

TROUBLESHOOTING



do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace-

ment parts for repairs.

State of abnormality Probable cause (malfunction) Remedy

Motor does not run. Battery cartridge is not installed. Install the battery cartridge.

Battery problem (under voltage) Recharge the battery cartridge. If recharging is not



The drive system does not work

correctly.

Ask your local authorized service center for repair.

Motor stops running after a little use. Battery's charge level is low. Recharge the battery cartridge. If recharging is not



Overheating. Stop using of tool to allow it to cool down.

The tool does not reach maximum

RPM.

Battery cartridge is installed improperly. Install the battery cartridge as described in this

manual.

Battery power is dropping. Recharge the battery cartridge. If recharging is not



The drive system does not work

correctly.

Ask your local authorized service center for repair.

Cutting tool does not rotate:

stop the machine immediately!





cutting tool.



Cutting tool is loosely attached. Tighten the cutting tool securely.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Abnormal vibration:

stop the machine immediately!

Broken, bent or worn cutting tool Replace the cutting tool.

Cutting tool is loosely attached. Tighten the cutting tool securely.

The drive system does not work

correctly.

Ask your local authorized service center for repair.

Cutting tool and motor cannot stop:

Remove the battery immediately!

Electric or electronic malfunction. Remove the battery cartridge and ask your local

authorized service center for repair.

OPTIONAL ACCESSORIES

WARNING: Only use the recommended

accessories or attachments indicated in this man-

ual. The use of any other accessory or attachment



CAUTION: These accessories or attachments

are recommended for use with your Makita tool

 The use of any other

accessories or attachments might present a risk of



for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Nylon cutting head

• Nylon cord (cutting line)

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may



19 FRANÇAIS

FRANÇAIS (Instructions originales)

SPÉCIFICATIONS

Modèle : UR014G

Type de poignée Poignée arceau

Vitesse à vide 0 - 5 000 min-1

Longueur totale

(sans outil de coupe et batterie)

1 857 mm

Diamètre du cordon en nylon 2,7 mm

Outil de coupe applicable et

diamètre de coupe



(P/N 1911Y3-7)

450 mm

Tension nominale 36 V - 40 V c.c. max.

Poids net 5,5 - 6,7 kg

Degré de protection IPX4

 



 

 

plus lourde, conformément à la procédure EPTA 01/2014, sont indiquées dans le tableau.

Batterie et chargeur applicables

Batterie BL4020 / BL4025 / BL4040 / BL4050F* / BL4080F*

* : Batterie recommandée

Chargeur DC40RA / DC40RB / DC40RC

• Certains chargeurs et batteries répertoriés ci-dessus peuvent ne pas être disponibles selon la région où vous

résidez.

AVERTISSEMENT : N’utilisez que les batteries et les chargeurs répertoriés ci-dessus. L’utilisation

d’autres batteries et chargeurs peut provoquer des blessures et/ou un incendie.

Source d’alimentation connectée par cordon recommandée

Support d’alimentation portable PDC01 / PDC1200

• La ou les sources d’alimentation connectées par cordon répertoriées ci-dessus peuvent ne pas être dispo-

nibles selon la région où vous résidez.

• Avant d’utiliser la source d’alimentation connectée par cordon, lisez les instructions et les avertissements

inscrits dessus.

Bruit

Norme applicable : ISO22868(ISO11806-1)/EN50636-2-91

Outil de coupe Niveau de pression sonore

(LpA) dB(A)

Niveau de puissance sonore

(LWA) dB(A)

(LpA) dB(A) Incertitude (K)

dB(A)

(LWA) dB(A) Incertitude (K)

dB(A)

 77,9 2,9 91,3 1,9

• Même si le niveau de pression sonore indiqué ci-dessus est inférieur ou égal à 80 dB (A), le niveau en fonction-

nement peut dépasser 80 dB (A). Portez un serre-tête antibruit.

NOTE : La ou les valeurs d’émission de bruit déclarées ont été mesurées conformément à la méthode de test

standard et peuvent être utilisées pour comparer les outils entre eux.

NOTE : La ou les valeurs d’émission de bruit déclarées peuvent aussi être utilisées pour l’évaluation préliminaire

de l’exposition.

20 FRANÇAIS

AVERTISSEMENT : Portez un serre-tête antibruit.

AVERTISSEMENT : 

la ou des valeurs déclarées, suivant la façon dont l’outil est utilisé, particulièrement selon le type de pièce

usinée.

AVERTISSEMENT : Les mesures de sécurité à prendre pour protéger l’utilisateur doivent être basées

sur une estimation de l’exposition dans des conditions réelles d’utilisation (en tenant compte de toutes

les composantes du cycle d’utilisation, comme par exemple le moment de sa mise hors tension, lorsqu’il

tourne à vide et le moment de son déclenchement).

Vibration

Norme applicable : ISO22867(ISO11806-1)

Outil de coupe Main gauche Main droite

ah,W (m/s2)Incertitude K

(m/s2)

ah,W (m/s2)Incertitude K

(m/s2)

 2,5 1,5 2,5 1,5

NOTE : La ou les valeurs de vibration totales déclarées ont été mesurées conformément à la méthode de test

standard et peuvent être utilisées pour comparer les outils entre eux.

NOTE : La ou les valeurs de vibration totales déclarées peuvent aussi être utilisées pour l’évaluation préliminaire

de l’exposition.

AVERTISSEMENT : -

rente de la ou des valeurs déclarées, suivant la façon dont l’outil est utilisé, particulièrement selon le type

de pièce usinée.

AVERTISSEMENT : Les mesures de sécurité à prendre pour protéger l’utilisateur doivent être basées

sur une estimation de l’exposition dans des conditions réelles d’utilisation (en tenant compte de toutes

les composantes du cycle d’utilisation, comme par exemple le moment de sa mise hors tension, lorsqu’il

tourne à vide et le moment de son déclenchement).

Symboles

Vous trouverez ci-dessous les symboles susceptibles

d’être utilisés pour l’appareil. Veillez à comprendre leur



Veuillez être prudent et rester attentif.

Lire le mode d’emploi.

Porter des lunettes de protection et un

serre-tête antibruit.

15m(50FT)Maintenez une distance d’au moins 15 m.





Avertissement ; Déconnectez la batterie

avant l’entretien.



plastique.

Ni-MH

Li-ion

Pour les pays de l’Union européenne uniquement

En raison de la présence de composants

dangereux dans l’équipement, les déchets

d’équipements électriques et électro-

niques, les accumulateurs et les batteries

peuvent avoir un impact négatif sur l’envi-

ronnement et la santé humaine.



électroniques ou les batteries avec les

ordures ménagères !

Conformément à la directive européenne

relative aux déchets d’équipements élec-

triques et électroniques et aux déchets

d’accumulateurs et de batteries, ainsi qu’à

son adaptation à la législation nationale,

les déchets d’équipements électriques,

les batteries et les accumulateurs doivent

être collectés séparément et déposés dans

un point de collecte distinct pour déchets

urbains, conformément aux réglementations

en matière de protection de l’environnement.

Cela est indiqué par le symbole de la pou-

belle à roulettes barrée sur l’équipement.

Niveau de puissance sonore garanti selon

la directive européenne sur le bruit dans

l’environnement.

Niveau de puissance sonore selon la

réglementation australienne NSW sur le

contrôle du bruit

Déclarations de conformité

Pour les pays européens uniquement

Les déclarations de conformité sont fournies en Annexe

A à ce mode d’emploi.

La page charge ...

Makita UR014G Manuel utilisateur

Makita UR014G Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents