Rode CASTER PRO II Mode d'emploi

Catégorie
Matériel musical
Taper
Mode d'emploi
QUICK START GUIDE
CONNECTIONS
Connect your RØDECaster PRO II as follows:
Plug the included USB-C power adaptor into the power connector (1)
Use the included USB-C cable to connect USB1 (2) to your computer
A microSD card can be inserted into the socket (3) if required.
The unit can be connected to an ethernet network using the CAT5 (4) socket if required.
Additional UISB devices (eg USB storage devices, mobile phoens etc) can be connected to the
USB2 connector (5). Additional cables (eg RØDE SC15 or 16) may be required
Headphones should be connected to the headphone outputs (6). Up to 4 pairs of headphones
can be connected.
Monitor speakers can be connected to the Line Out (7) if required.
Microphones and / or musical instruments are connected to the XLR Combi inputs (8).
POWERING THE UNIT ON AND OFF
To turn the unit on, press the red power button on the left of the back panel.
To turn the unit off, press this button again, and then follow the prompts on the screen of the unit.
CONNECTING TO A NETWORK
To connect the unit to a network, either:
1) Use an ethernet cable to connect the unit to a network router
2) Connect the unit to WiFi by following the on-screen prompts
FRONT PANEL CONTROLS
1) Multi-function touch screen
2) Record button. Press to start a recording. Press again to stop the recording.
3) Channel access button. Press to access channel functions for each fader.
4) Faders. Slide up and down to control the volume of each audio source.
5) Mute and solo buttons. Use to mute a specific channel, and to listen to a specific channel in
headphone output 1.
6) Headphone volume controls.
7) Rotary encoder. Use to alter parameter values in conjunction with the multi-function touch
screen
8) SMART pads. Press to trigger sounds and other actions.
9) Pad bank controls. Use to switch between pages of SMART pads.
REGULATORY AND SAFETY GUIDE
Leitfaden für Sicherheit und Vorschriften
Manufacturer: DE
Address: 107 Carnarvon Street, Silverwater,
NSW 2128 Australia
EU Importer: DE EU
Address: Neukirchner Str. 18, 65510
Hünstetten, Germany
UK Importer: DE UK
Address: Unit A, 23-25 Sunbeam Rd, London
NW10 6JP, United Kingdom
Important Safety Information
1. Read and understand the instructions and safety guide completely before using the product.
2. Ensure both the instruction manual and regulatory and safety guide are accessible to all users,
including when passing the product on to third parties.
3. Only use this product with authorized RØDE accessories.
4. Do not open the product housing. This will avoid the warranty.
5. Refer all service and repairs to DE-approved service personnel. Service or repair is
required for products that have been damaged, exposed to liquid, rain or moisture, or do not
operate normally.
6. Use the product only in the ways described in the instructions.
7. Do not use the product if it was damaged during transportation.
8. Keep the product away from liquids and electrically conductive objects that are not necessary
for the operation.
9. Do not use any solvents or corrosive cleaning agents to clean the product.
10. Do not adjust the control of the product in an environment that requires your attention
(Operating machinery, driving, etc.).
11. Battery cannot be subjected to high or low extreme temperatures, low air pressure at high
altitude during use, storage or transportation.
12. Replacement of a battery with an incorrect type that can result in an explosion or the leakage
of flammable liquid or gas.
13. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery,
that can result in an explosion.
14. Leaving a battery in an extremely high temperature surrounding environment that can result in
an explosion or the leakage of flammable liquid or gas.
15. A battery subjected to extremely low air pressure that may result in an explosion or the
leakage of flammable liquid or gas.
Wichtige Sicherheitsinformationen
1. Die Anweisungen und der Sicherheitsleitfaden sind vor der Verwendung des Produkts
vollständig zu lesen und zu beachten.
2. Stellen Sie sicher, dass sowohl die Betriebsanleitung als auch der Leitfaden r Vorschriften
und Sicherheit r alle Benutzer zugänglich sind, auch bei Weitergabe des Produkts an Dritte.
3. Verwenden Sie dieses Produkt nur mit autorisiertemDE-Zubehör.
4. Öffnen Sie das Produktgehäuse nicht. Dadurch entfällt die Garantie.
5. Überlassen Sie alle Service- und Reparaturarbeiten von DE autorisiertem Servicepersonal.
Bei Produkten, die beschädigt wurden; die Flüssigkeit, Regen oder Feuchtigkeit ausgesetzt
waren; oder die nicht normal funktionieren, ist eine Wartung oder Reparatur erforderlich.
6. Verwenden Sie das Produkt nur auf die in der Anleitung beschriebene Weise.
7. Verwenden Sie das Produkt nicht, wenn es beim Transport beschädigt wurde.
8. Halten Sie das Produkt von Flüssigkeiten und elektrisch leitenden Gegenständen fern, die r
den Betrieb nicht erforderlich sind.
9. Verwenden Sie zur Reinigung des Produkts keine Lösungsmittel oder ätzende Reinigungsmittel.
10. Nehmen Sie keine Einstellungen am Produkt vor, wenn Sie in einer Umgebung sind, die Ihre
Aufmerksamkeit erfordert (Bedienung von Maschinen, Autofahren usw.).
11. Die Batterie darf hrend des Gebrauchs, der Lagerung oder des Transports keinen
extremen Temperaturen, niedrigem Luftdruck oder großer Höhe ausgesetzt werden.
12. Das Ersetzen einer Batterie durch einen falschen Typ kann zu einer Explosion oder zum Austritt
von brennbarer Flüssigkeit oder Gas führen.
13. Das Wegwerfen einer Batterie ins Feuer oder in einen heißen Ofen oder mechanisches
Zerkleinern oder Zerschneiden einer Batterie kann zu einer Explosion führen.
14. Wenn Sie die Batterie extrem hohen Temperaturen aussetzen, kann dies zu einer Explosion
oder zum Austreten von entflammbaren Flüssigkeiten oder Gasen hren.
15. Wenn Sie die Batterie extrem niedrigem Luftdruck aussetzen, kann dies zu einer Explosion
oder zum Austreten von brennbaren Flüssigkeiten oder Gasen führen.
North America
The DE Caster Pro II must not be co-located or operated in conjunction with any other antenna or
transmitter.
The device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are design to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to with the receiver is
connected.
4. Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth an uncontrolled environment.
Changes or modifications not expressly approved by RØDE could void the user’s authority to operate
the equipment.
This device is acting as slave and operating in the 2.4GHz (2412-2462 MHz) and 5GHz (5150-5850
MHz) band. Ad Hoc function is supported but not able to operate on non-US frequencies.
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage ;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment shall be installed and operated with minimum distance 20cm between the radiator &
body.
Radio Frequency Exposure Statement for Canada
The device has been evaluated to meet general RF exposure requirements. The device can be used in
mobile exposure conditions. The min separation distance is 20cm.
claration d'exposition aux radiofréquences pour IC
L'appareil a é évalué pour pondre aux exigences rales en matière d'exposition aux RF.
L'appareil peut être utilisé dans des conditions d'exposition mobiles. La distance de séparation
minimale est de 20cm.
Operation of this device is restricted to indoor use only. (W52 band)
Le fonctionnement de cet appareil est limité à une utilisation en intérieur uniquement. (W52 band)
For USA: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and U-
NII-3 meets the requirements of 47 CFR FCC Part15.407(g), and the manufacturer declares that their
transmission is maintained at Band U-NII-1, U-NII 2A, U-NII 2C and U-NII-3.
For Canada: The frequency stability of all transmission frequencies of U-NII-1, U-NII 2A, U-NII 2C and
U-NII-3 meets the 47 CFR FCC Part15.407(g) requirements, and the manufacturer states that their
transmissions remain within the U-NII-1, U-NII 2A, U-NII 2C and U-NII-3 bands.
Pour le Canada : La stabilité de fréquence de toutes les fréquences de transmission de U-NII-1, U-NII
2A, U-NII 2C et U-NII-3 est conforme aux exigences 47 CFR FCC Part15.407(g), et le fabricant
clare que leurs transmissions restent dans les bandes U-NII-1, U-NII 2A, U-NII 2C et U-NII-3.
EU Compliance Statement
DE hereby declares that the RØ DECaster Pro II is in compliance with Radio Directive 2014/53/EU.
A copy of the declaration of conformity is available at http://www.rode.com/
For details of EU representative go to http://en.rode.com/distributors
Operating Frequency Range
The maximum RF Output
Power
Bluetooth 2402 2480 MHz
3.68 dBm (BR/EDR)
4.59 dBm (BLE) EIRP
WiFi 2412 2472 MHz
15.99 dBm EIRP
WiFi 5150-5250 MHz
16.71 dBm EIRP
WiFi 5250-5350 MHz
16.71 dBm EIRP
WiFi 5470-5725 MHz
16.71 dBm EIRP
WiFi 5725-5850 MHz
14 dBm EIRP
2.4G SRD 2402-2480 MHz
1.19 dBm EIRP
Caution
The RØ DECaster Pro II has been designed to be used with the provided power supply, as use the provided
power supply only.
Stop using the power supply unit and any cables if:
1. There is any damage to the charging port, power connector or power cord.
2. The power supply unit is exposed to excessive moisture, or liquids is spilled into the power supply unit.
3. The power supply unit enclosure is broken.
Power Supply Unit Specifications
Model Name: YDSPD030/YDS-PD030/YDS-PD030A
Frequency: 50-60 Hz
Line Voltage: 100-240 V
Output Ratings: 20V 1.5A; 15V 2.0A; 12V 2.5A; 9V 3A; 5V 3A
TAIWAN
Note: For regulatory information such as identification numbers go to Settings > System > Information > View
Device Information > Compliance & Regulatory
UK
USA
FCC ID: 2AEAN-RCPII
CANADA IC: 20091-RCPII
AS/NZS
SOUTH KOREA
ID: R-R-R72-RCP-II
Company Name: RØDE
Model: DECaster Pro II
Country of Origin: Australia
TAIWAN
[Include Logo and ID]
JAPAN
To prevent possible hearing damage, do not listen at high volume levels for long periods.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Rode CASTER PRO II Mode d'emploi

Catégorie
Matériel musical
Taper
Mode d'emploi

dans d''autres langues