Zebra EC500K Mode d'emploi

Marque: Zebra

Modèle: EC500K

Taper: Mode d'emploi

ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corp., registered in many jurisdictions

partnumber-xxEN Rev. A

EC500K

Regulatory Guide

Regulatory Information

This device is approved under Zebra Technologies Corporation.

This guide applies to the following model number: EC500K

All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold

and will be labeled as required.

Local language translation / Tradução do idioma local / Übersetzung in die lokale Sprache / Raduccion de

idioma local / Traduction en langue locale / Prijevod na lokalni jezik / Traduzione in lingua locale / 現地語

の翻訳 / 현지 언어 번역 / Перевод на местный язык / 本地語言翻譯 / 本地语言翻译 / Yerel dil çeviri

/Tłumaczenie na język lokalny : www.zebra.com/support

Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user’s

authority to operate the equipment.

Declared maximum operating temperature: 50°C

Bluetooth® Wireless Technology

This is an approved Bluetooth® product. For more information on the Bluetooth SIG listing, please visit

www.bluetooth.com.

不在中国之外销售服务和使用

Regulatory Markings

Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved

for use. Refer to the Declaration of Conformity (DoC) for details of other country markings. The DOC is

available at: www.zebra.com/doc.

The regulatory marks specific to this device (including FCC and ISED) are available on the screen of the

device by following these instructions:

Go to Settings > Regulatory.

Health and Safety Recommendations

Ergonomic Recommendations

In order to avoid or minimize the potential risk of ergonomic injury, always follow good ergonomic

workplace practices. Consult with your local Health and Safety Manager to ensure that you are adhering to

your company’s safety programs to prevent employee injury.

Vehicle Installation

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles

(including safety systems). Check with the manufacturer or its representative regarding your vehicle.

Ensure the equipment is installed to avoid driver distractions. You should also consult the manufacturer

about any equipment that has been added to your vehicle.

Position the device within easy reach. User should be able to access the device without removing their

eyes from the road.

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

IMPORTANT: Before installing or using, check national and local laws regarding distracted driving.

Safety on the Road

Give your full attention to driving. Obey the laws and regulations on the use of wireless devices in the

areas where you drive.

The wireless industry reminds you to use your device / phone safely when driving.

Restricted Use Locations

Remember to observe restrictions and obey all signs and instructions on the use of electronic devices in

restricted use locations.

Safety in Hospitals and Aircraft

NOTE: Wireless devices transmit radio frequency energy that may affect medical electrical

equipment and aircraft’s operation. Wireless devices should be switched off wherever you are

requested to do so in hospitals, clinics, healthcare facilities or by airline staff. These requests are

designed to prevent possible interference with sensitive equipments.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure – Use Properly

Only operate the device in accordance with the instructions supplied.

The device complies with internationally recognized standards covering human exposure to

electromagnetic fields. For information on international human exposure to electromagnetic fields, refer to

the Zebra Declaration of Conformity (DoC) at www.zebra.com/doc.

Use only Zebra tested and approved headset, belt-clips, holsters, and similar accessories to ensure RF

exposure compliance. If applicable, follow the instructions for use as detailed in the accessory guide.

The use of third-party belt clips, holsters, and similar accessories may not comply with RF exposure

compliance requirements and should be avoided.

For further information on the safety of RF energy from wireless devices, refer to RF exposure and

assessment standards section at www.zebra.com/responsibility.

Handheld or Body-Worn Devices

To satisfy RF exposure requirements, this device must operate with a minimum separation distance

of 1.5 cm or more from a user's body and nearby persons.

LED Devices

Classified as ‘EXEMPT RISK GROUP’ according to IEC 62471:2006 and EN 62471:2008.

Pulse Duration: 22.8 ms (SE4100)

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

Power Supply

WARNING ELECTRICAL SHOCK: Use only a Zebra approved, Certified ITE [SELV] power supply

with appropriate electrical ratings. Use of alternative power supply will invalidate any approvals

given to this unit and may be dangerous.

Batteries and Power Packs

This information applies to Zebra-approved batteries and power packs containing batteries.

Battery Information

CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of batteries

according to instructions.

Use only Zebra approved batteries. Accessories which have battery charging capability are

approved for use with the following battery models:

•Model BT-000424 (3.85 VDC, 3000 mAh)

•Model BT-000424A (3.85 VDC, 4100 mAh)

Zebra approved rechargeable battery packs are designed and constructed to the highest standards within

the industry.

However, there are limitations as to how long a battery can operate or be stored before needing

replacement. Many factors affect the actual life cycle of a battery pack such as heat, cold, harsh

environmental conditions, and severe drops.

When batteries are stored over six months, some irreversible deterioration in overall battery quality may

occur. Store batteries at half charge in a dry, cool place, removed from the equipment to prevent loss of

capacity, rusting of metallic parts, and electrolyte leakage. When storing batteries for one year or longer,

the charge level should be verified at least once a year and charged to half charge.

Replace the battery when a significant loss of run time is detected.

•Standard warranty period for all Zebra batteries is one year, regardless if the battery was purchased

separately or included as part of the host device. For more information on Zebra batteries, please visit:

www.zebra.com/batterydocumentation and select the Battery Best Practices link.

Battery Safety Guidelines

IMPORTANT – SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS

WARNING – When using this product basic safety precautions should always be followed,

including the following:

The area in which the units are charged should be clear of debris and combustible materials or

chemicals. Particular care should be taken where the device is charged in a non-commercial environment.

•Read all the instructions before using the product.

•Follow battery usage, storage, and charging guidelines found in the user's guide.

•Improper battery use may result in a fire, explosion, or other hazard.

To charge the mobile device battery, the battery and charger temperatures must be between

0°C and +40°C (+32°F and +104°F).

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a

risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a

battery or a charger, contact Zebra support.

For devices that utilize a USB port as a charging source, the device shall only be connected to products

that bear the USB-IF logo or have completed the USB-IF compliance program.

Do not disassemble or open, crush, bend or deform, puncture, or shred. Damaged or modified batteries

may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.

Severe impact from dropping any battery-operated device on a hard surface could cause the battery to

overheat.

Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.

Do not modify, disassemble, or remanufacture, attempt to insert foreign objects into the battery, immerse

or expose to water, rain, snow or other liquids, or expose to fire, explosion, or other hazard.

Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or

near a radiator or other heat source. Do not place battery into a microwave oven or dryer.

To reduce the risk of injury, close supervision is necessary when used near children.

Please follow local regulations to promptly dispose of used re-chargeable batteries.

Do not dispose of batteries in fire. Exposure to temperatures over 100°C (212°F) may cause explosion.

Seek medical advice immediately if a battery has been swallowed.

In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has

been made, wash the affected area with large amounts of water and seek medical advice.

If you suspect damage to your equipment or battery, contact Zebra support to arrange for inspection.

Marking and European Economic Area (EEA)

Statement of Compliance

Zebra hereby declares that this radio equipment is in compliance with Directives 2014/53/EU and

2011/65/EU.

Any radio operation limitations within EEA countries are identified in Appendix A of EU Declaration of

Conformity. The full text of the EU Declaration of Conformity is available at: www.zebra.com/doc.

Waste Electrical and Electronic Equipment (WEEE)

For EU Customers: For products at the end of their life, please refer to recycling/disposal advice at:

www.zebra.com/weee.

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

United States and Canada Regulatory

Radio Frequency Interference Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable

protection against harmfulb interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Radio Frequency Interference Requirements – Canada

Innovation, Science and Economic Development Canada ICES-003 Compliance Label: CAN ICES-3

([B])/NMB-3([B])

This device complies with Innovation, Science and Economic Development Canada’s licence-exempt

RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of

the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi même si le

brouillage est susceptible d'en compromettre le fonctionnement.

This device is restricted to indoor use when operating in the 5150 to 5350 MHz frequency range.

Lorsqu'il fonctionne dans la plage de fréquences 5 150- 5350 MHz, cet appareil doit être utilisé

exclusivement en extérieur.

RF Exposure Requirements - FCC and ISED

The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated in

compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC

and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid.

Handheld Devices

To satisfy RF exposure requirements, this device must operate with a minimum separation distance of 1.5

cm or more from a user's body and nearby persons.

Pour satisfaire aux exigences d'exposition aux radio fréquences, cet appareil doit fonctionner avec une

distance de séparation minimale de 1.5 cm ou plus de corps d'une personne.

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

Co-located Statement

To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not

be co-located (within 20 cm) or operating in conjunction with any other transmitter/antenna except those

already approved in this filling.

This device is marked HAC showing compliance with the applicable requirements of FCC Part 68 and

ISED CS-03-Part 5.

UL Listed Products with GPS

Underwriters Laboratories Inc. (UL) has not tested the performance or reliability of the Global Positioning

System (GPS) hardware, operating software, or other aspects of this product. UL has only tested for fire,

shock, or casualties as outlined in UL’s Standard(s) for Safety for Information Technology Equipment. UL

Certification does not cover the performance or reliability of the GPS hardware and GPS operating

software. UL makes no representations, warranties, or certifications whatsoever regarding the

performance or reliability of any GPS related functions of this product.

Marquage UL des produits équipés d'un GPS

Les tests menés par Underwriters Laboratories Inc. (UL) ne portent ni sur les performances, ni sur la

fiabilité du matériel et du logiciel d'exploitation du GPS (Global Positioning System), ni sur tout autre

aspect de ce produit. UL a uniquement testé la résistance au feu, aux chocs et aux sinistres, comme le

définit la norme UL60950-1 relative à la sécurité des matériels de traitement de l'information. La

certification UL ne couvre ni les performances, ni la fiabilité du matériel et du logiciel d'exploitation GPS.

UL ne formule aucune déclaration, ni ne délivre aucune garantie ni aucun certificat concernant les

performances et la fiabilité des fonctions GPS de ce produit.

Brasil

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar

interferência em sistemas devidamente autorizados.

Este produto está homologado pela Anatel de acordo com os procedimentos regulamentados para

avaliação da conformidade de produtos para telecomunicações e atende aos requisitos técnicos

aplicados, incluindo os liYDmites de exposição da Taxa de Absorção Específica referente a campos

elétricos, magnéticos e eletromagnéticos de radiofrequência.

SAR VALUES NEEDED

Valores de SAR medidos:

•Cabeça: xxxx W/kg

•Corpo: xxxx W/kg

Valores de SAR medidos

Nº do modelo Cabeça W/kg Corpo W/kg

1-model# xxxx xxxx

2-model# xxxx xxxx

3-model# xxxx xxxx

4-model# xxxx xxxx

5-model# xxxx xxxx

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

Este dispositivo está em conformidade com as diretrizes de exposição a radiofrequência quando

posicionado à pelo menos 1.5 cm do corpo.

中国

通过访问以下网址可下载当地语言支持的产品说明书 www.zebra.com/support

确认进网标贴和证书真伪可查询网址 : www.tenaa.com.cn/.

锂电池安全警示语 :

警告：请勿拆装，短路，撞击，挤压或者投入火中

注意：如果电池被不正确型号替换，或出现鼓胀，会存在爆炸及其他危险

请按说明处置使用过的电池

电池浸水后严禁使用

SAR VALUES NEEDED

本产品电磁辐射比吸收率（SAR）最大值为 xxxx W/kg，符合国家标准 GB 21288-2007 的要求。

如果配套使用外部电源适配器，请确保其已通过 CCC 认证

“线录术 ”场线

调开关

场扩频围额频

线

对线产

应当辐频疗 ISM 应线

对线产时应继续

规关规标卫

测测

导军线场环区内

应当环关规

场为圆径 5000 遥

6-model# xxxx xxxx

7-model# xxxx xxxx

8-model# xxxx xxxx

Valores de SAR medidos

Nº do modelo Cabeça W/kg Corpo W/kg

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

产品中有害物质的名称及含量

ROHS TABLE VALUES NEEDED

Colombia

Señor usuario, la siguiente información se entrega de conformidad con lo establecido en el Régimen de

protección de los derechos de los usuarios, expedido por la Comisión de Regulación de Comunicaciones.

Recomendaciones de uso:

1. Utilice siempre que pueda dispositivos manos libres.

2. Evite utilizar el equipo mientras conduce un vehículo.

3. En caso que el teléfono sea utilizado por niños, ancianos, mujeres embarazadas y población

inmunocomprometida, consulte a su médico y el manual del equipo.

4. Si usted utiliza algún dispositivo electrónico de uso médico, asegúrese que el mismo esté protegido

contra las ondas de radiofrecuencia externas.

5. Apague su teléfono en lugares tales como: hospitales, centros de salud, aviones, estaciones de

suministro de combustible, en presencia de gases explosivos y lugares donde se realizan explosiones.

6. Evite que terceros hagan uso de su teléfono para prevenir la implantación de dispositivos como

programas espías (spyware) o identificadores ocultos, que atentan contra la seguridad de la

información contenida en el mismo.

Евразийский Таможенный Союз (EAC)

Данный продукт соответствует требованиям знака EAC.

部件名称 (Parts)

有害物质

铅(Pb) 汞(Hg) 镉(Cd) 六价铬

(Cr(VI))

多溴联

苯

(PBB)

多溴二

苯醚

(PBDE)

金属部件 (Metal Parts)

电路模块 (Circuit

电缆及电缆组件 (Cables

塑料和聚合物部件

光学和光学组件 (Optics

(Print Heads)

电池 (Batteries)

(Ext. Pwr Sply)

本表格依据 SJ/T 11364 的规定编制。

O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。( 企业可在此

处，根据实际情况对上表中打 “×” 的技术原因进行进一步说明。

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

France

Cet appareil a été testé et déclaré conforme aux limites applicables d'exposition aux radiofréquences (RF).

Le débit d'absorption spécifique (DAS) local quantifie l'exposition de l'utilisateur aux ondes

électromagnétiques de l'équipement concerné.

Les valeurs SAR les plus élevées sont disponibles sur la déclaration de conformité (DoC) disponible sur:

www.zebra.com.

India

The sending and receiving of texts is supported in the following Indian languages:

Assamese, Bengali, Gujarati, Hindi, Kannada, Kashmiri, Konkani, Malayalam, Manipuri, Marathi, Nepali,

Oriya, Punjabi, Sanskrit, Sindhi, Tamil, Telugu, Urdu, Bodo, Santhali, Maithili, and Dogri.

México

La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o

dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier

interferencia, incluyendo la que pueda causar su operación no deseada.

한국

전자파흡수율

본 제품의 전자파흡수율은 과학기술정보통신부의 「전자파 인체보호기준」을 만족합니다 . 본 제품은

국립전파연구원의 「전자파흡수율 측정기준」에 따라 최대 출력 조건에서 머리에 근접하여 시험되었으며 ,

최대 전자파흡수율 측정값은 다음과 같습니다 .

모델명 : EC500K

머리 전자파흡수율 : xxxx W/kg

전자파흡수율 (SAR : Specified Absorption Rate) 은 휴대전화를 사용할 때 인체에 흡수될 수 있는 전자파의

양으로 우리나라는 국제권고기준인 2 W/kg 보다 엄격한 1.6 W/kg 기준을 적용하고 있습니다 .

그러나 일상생활에서는 최대출력보다 현저히 낮은 출력 상태에서 통신이 이루어지므로 전자파흡수율은 위

시험 결과보다 매우 낮습니다 .

전자파흢율에 대한 자세한 정보는 국립전파연구원 (www.rra.go.kr) 또는 제조사 홈페이지에서 확인할 수

있습니다 .

ࢷળئࢿ࣏ࢂ߾Ҭհࢷیળ஘ܹ࡭ҟ̗

ᘨఘጀݠ₈ℴ᧜ⰼ₨◤ゑᭈ⁘⁰ج⺉ݠ᭐ⅅᘤ⫥ᰐᚰ

 ℴ⃀ⰼ₨◤ᘤ⽨ݠ∰ἀℱ⺙⺙௸ఔ



SAR

ܹ➈ᔿมܹݠ∰ἀذ⺌᧱ᩨ⺌ⅅᘤ௄



www.rra.go.kr

ཀ௄⅌↠᧜⽸Ⳉ₤⋰ἀᩌ

 ⾅₨⺈ᰔᭈ₸ᯥ௸ఔ

ࢷળئࢿ࣏ࢂ߾Ҭհࢷیળ஘ܹ࡭ҟ̗

ᘨఘጀݠ₈ℴ᧜ⰼ₨◤ゑᭈ⁘⁰ج⺉ݠ᭐ⅅᘤ⫥ᰐᚰ

 ℴ⃀ⰼ₨◤ᘤ⽨ݠ∰ἀℱ⺙⺙௸ఔ



SAR

ܹ➈ᔿมܹݠ∰ἀذ⺌᧱ᩨ⺌ⅅᘤ௄



www.rra.go.kr

ཀ௄⅌↠᧜⽸Ⳉ₤⋰ἀᩌ

 ⾅₨⺈ᰔᭈ₸ᯥ௸ఔ

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

해당 제품은 xxxx mm 거리에서 전자파흡수율 테스트를 통과 하였습니다 .

臺灣

取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更

原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，

應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

應避免影響附近雷達系統之操作

公司資訊

台灣斑馬科技股份有限公司 / 台北市信義區松高路 9 號 13 樓

行政院環保署 (EPA) 要求乾電池製造或進口商，需依廢棄物清理法第 15 條之規定，於販

售、贈

送或促銷的電池上標示回收標誌。請聯絡合格的台灣回收廠商，以正確棄置電池。

限用物質含有情況標示聲明書

ROHS TABLE VALUES NEEDED

Türkiye

Bu cihaz Türkçe karakterlerin tamamını ihtiva eden ETSI TS 123.038 V8.0.0 (veya sonraki sürümünkodu)

ve ETSI TS 123.040 V8.1.0 (veya sonraki sürümün kodu) teknik özelliklerine uygundur.

TÜRK WEEE Uyumluluk Beyanı

EEE Yönetmeliğine Uygundur.

設備名稱 (Product Description in CHINESE

Equipment name) 型號（型式）

Model Type designation (Type)

單元 Unit

限用物質及其化學符號

Restricted substances and its chemical symbols

鉛

(Pb) 汞

(Hg) 鎘

(Cd) 六價鉻

(Cr+6) 多溴聯苯

(PBB) 多溴二苯醚

(PBDE)

印刷電路板及電子組件

金屬零件

電纜及電纜組件

塑料和聚合物零件

光學與光學元件 —

備考 1. 〝超出 0.1 wt % 〞及〝超出 0.01 wt % 〞係指限用物質之百分比含量超出百分比含量基準值。

備考 2. 〝 O 〞係指該項限用物質之百分比含量未超出百分比含量基準值。

備考 3. 〝−〞係指該項限用物質為排除項目。

Note 1: “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the percentage content of the restricted substance exceeds

the reference percentage value of presence condition.

Note 2: “O” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of

presence.

Note 3: The “ − ” indicates that the restricted substance corresponds to the exemption.

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

ประเทศไทย

เครื่ องโทรคมนาคมและอุปกรณ นี้ มีความสอดคลองตามขอกําหนดของ กทช .

เครื่ องวิทยุคมนาคมนี้ มี อั ตราการดูดกลืนพลังงานจําเพาะ (Specific Absorption Rate – SAR)

อั นเนื่ องมาจากเครื่ องวิทยุคมนาคมเทากับ

•EC500K 1.141 w/kg

ซึ่งสอดคลองตามมาตรฐานความปลอดภัยตอสุขภาพของมนุษยจากการใชเครื่องวิทยุคมนาคมที่คณะกรรมการกิจการโ

ทรคมนาคมแหงชาติประกาศกําหนด

เครื่ องวิทยุคมนาคมนี้ มี ระดับการแผคลื่ นแมเหล็กไฟฟาสอดคลองตาม

มาตรฐานความปลอดภัยตอสุขภาพของมนุษยจากการใชเครื่ องวิทยุคมนาคมที่ คณะกรรมการกิจการ

โทรคมนาคมแหงชาติประกาศกําหนด

Warranty

For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.

Service Information

Before you use the unit, it must be configured to operate in your facility's network and run your

applications.

If you have a problem running your unit or using your equipment, contact your facility's Technical or

System Support. If there is a problem with the equipment, they will contact Zebra support at

zebra.com\support.

For the latest version of the guide go to: zebra.com\support.

Software Support

Additional Information

For information on using the EC500K, refer to the EC500K product guide available at: zebra.com/support.

REVIEW ONLY 8/31/20

EC500K Regulatory Guide

Warranty

For the complete Zebra hardware product warranty statement, go to: zebra.com\warranty.

Service Information

Before you use the unit, it must be configured to operate in your facility's network and run your

applications.

If you have a problem running your unit or using your equipment, contact your facility's Technical or

System Support. If there is a problem with the equipment, they will contact Zebra support at

zebra.com\support.

For the latest version of the guide go to: zebra.com\support.

Software Support

Zebra wants to ensure that customers have the latest entitled software at the time of device purchase in

order to keep the device operating at peak performance levels. To confirm that your Zebra device has the

latest entitled software available at the time of purchase, visit www.zebra.com/support.

Check for the latest software from Support > Products, or search for the device and select Support >

Software Downloads.

If your device does not have the latest entitled software as of your device purchase date, e-mail Zebra at

entitlementservices@zebra.com and ensure you include the following essential device information:

•Model number

•Serial number

•Proof of purchase

•Title of the software download you are requesting.

If it is determined by Zebra that your device is entitled to the latest version of software, as of the date you

purchased your device, you will receive an e-mail containing a link directing you to a Zebra Web site to

download the appropriate software.

Additional Information

For information on using the family name, refer to the family name product guide available at: web

address.

REVIEW ONLY 8/31/20

Zebra EC500K Mode d'emploi

Marque: Zebra

Modèle: EC500K

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Zebra EC500K User guide

Zebra EC500K Mode d'emploi

Zebra EC500K Mode d'emploi

dans d''autres langues

Documents connexes