Samsung Electronics WIC213S Manuel utilisateur

WIC213S
Samsung Electronics
Marque
Samsung Electronics
Modèle
WIC213S
Taper
Manuel utilisateur
Theory of Operation WIC213S IoT Module
SAMSUNG ELECTRONICS 09/07/22
Introduction
The WIC213S is a IoT Module for Home automation networks.
Connected to the Monitor-remote control device, it acts as a pathway between remote home
automation.
Power is provided by External 5V power supply with 10pin zip type connector.
Networking
The WIC2131S is applied EFR32 IoT Multi-Protocol of Silicon Labs.
The IoT Module delivers the information received from the remote control device to the main
board with 10pin zip type connector.
Power Source
The WIC213S is powered by an external 5VDC@500mA regulated power source with
10pin zip type connector.
Indication
None.
Expansion Ports
None.
Eurpoe
US/Canada
FCC approval
This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two
Conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undes-
irable operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in aresidential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installedand used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this e-
quipment doescause harmful interference to radio or television reception, which can be determ-
ined by turning the equipment off and on, the user is encouraged to try to correct the interferenc
e by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/ TV technician for help.
-The OEM integrator is responsible for ensuring the end-user has no manual instruction to
remove or install module.
3. Max RF output power e.i.r.p. 9.17 dBm.
-The module is limited to installation in mobile or fixed applications.
IC approval
This device contains licence-
exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
development Canada’s licenceexempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired oper
ation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’
Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptib
le d’en compromettre le fonctionnement.
IMPORTANT NOTE
This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environ
ment. This device should be installed and must not be colocated or operating in conjunction
with any other antenna or transmitter.
This device is intended only for OEM integrators under the following conditions:
1) This module may not be co-located with any other transmitters or antennas.
2) The antenna must be installed such that 20cm is maintained between the antenna and users.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end product for any additional compliance
requirements with this module installed.
In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer
considered valid and the FCC ID cannot be used on the final product. In these circumstances,
the OEM integrator will be responsible for reevaluating the end product including this module
and obtaining separate FCC & IC authorizations.
Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environne
ment non contrôlé.
Cet appareil doit être installé et ne doit pas être co-localisées ou opérant en conjonction avec
une autre antenne ouun autre émetteur.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes :
1 ) L' antenne doit être installée de telle sorte que 20 cm est maintenue entre l'antenne et les utili
sateurs .
2 ) Ce module ne peut pas être co-localisé avec d'autres émetteurs ou des antennes .
Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplément
aires ne serontpas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs
produits finis pour toutes lesexigences de conformité supplémentaires avec ce module installé.
Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne so
nt plus considérés comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final.
Dans ces circonstances, l'intégrateur OEM sera responsable de réévaluer le produit final, y
compris l'obtention de ce module et séparée de la FCC et IC Autorisations
User Information
Caution: Any changed or modifications not expressly approved by the party responsible for compl
iance could void the user`s authority to operate this equipment.
Attention: Toute changé ou modifications non expressément approuvés par la partie responsable
de la conformité pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.
Supplemental User’s Manual
INTEGRATION INSTRUCTIONS per FCC KDB 996369 D03, Section 2.0
2.2 List of applicable FCC rules
The module has been certified for use under FCC Part 15.247 only
2.3 Summarize the specific operational use conditions
The host device must be tested for spurious emissions due to the module’s lack of its own shielding.
2.4 Limited module procedures
The host device must be tested for spurious emissions due to the module’s lack of its own shielding.
2.5 Trace antenna designs
Antenna is integrated into module and the module should be used with no other antennas
2.6 RF exposure considerations
The antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any other
antenna or transmitter device.
2.7 Antennas
Antenna is soldered on the module and and the module should be used with no other antennas.
2.8 Label and compliance information
Module contains its own label
2.9 Information on test modes and additional testing requirements
None required.
2.10 Additional testing, Part 15 Subpart B disclaimer
This module has been tested and certified to comply with FCC Part 15C requirements. The host
device to which it is installed may require additional testing to show compliance with FCC Part 15B
requirements.
Supplemental User’s Manual
INTEGRATION INSTRUCTIONS per FCC KDB 996369 D03, Section 2.0
Notice:
OEM should include the following warnings on the label:
“Contains FCC ID:********, IC Number:********”
As well as the model name:
“*********”
Installer should include the following in the user’s manual:
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.”
“Changes of modification not expressly approved by the party responsible for compliance could void
the
user’s authority to operate the equipment.”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Samsung Electronics WIC213S Manuel utilisateur

WIC213S
Samsung Electronics
Marque
Samsung Electronics
Modèle
WIC213S
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents