Balt Compass Cabinet Accessory Assembly Instructions

Taper
Assembly Instructions

Ce manuel convient également à

Cabinet Lectern Mount
UPDATED AS OF: 05/05/2020 1 of 6
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
P1 - Lectern Top
P2 - Book Stop
P3 - Left Support Tube
P4 - Right Support Tube
x1
x1
x2
x2
A - #10 x 1” Wood Screw
B - M4 x 30mm Screw
x8
x2
Parts List
UPDATED AS OF: 05/05/2020 2 of 6
Hardware
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
UPDATED AS OF: 05/05/2020 3 of 6
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
comptes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient seres.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 05/05/2020 4 of 6
STEP 2
Attach Book Stop to Lectern Top using two screws.
Take out drawers if necessary. Remove casting retainer screws from
positions shown inside cabinet. Set screws aside. Repeat on other
side of cabinet.
B
P1
P2
STEP 3
UPDATED AS OF: 05/05/2020 5 of 6
STEP 4
Insert Support Tubes into slots in mount castings. For tubes inserted in front, line up top holes
with screw holes from Step 2. For tubes inserted in the back, line up with bottom holes (See
page 6 for Support Height Addendum). Replace screws removed in previous step.
Using pre-drilled holes in bottom of Lectern Top as guides, secure top to supports with wood
screws driven directly into underside of top. Make sure Book Stop is at the front.
A
Top Hole
Bottom Hole
P4
P3
THIS COMPLETES ASSEMBLY INSTRUCTION
Support Height Addendum
UPDATED AS OF: 05/05/2020 6 of 6
Use the distances below while setting back Support Tubes in Step 3 to ensure correct transaction
top height. Distances are provided for each of three cabinet height options and are measured
from ground to top of back Support Tube.
H1: 32”
H2: 42.25”
H3: 57.25”
Cabinet Ogee Option
UPDATED AS OF: 07/14/2020 1 of 6
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
P1 - Panel
P2 - Upright
P3 - Base
P4 - Top Cap
x2
x2
x1
x1
A - M6 x 12.5mm Screw x8
Parts List
UPDATED AS OF: 07/14/2020 2 of 6
Hardware
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
UPDATED AS OF: 07/14/2020 3 of 6
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
comptes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient seres.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 07/14/2020 4 of 6
STEP 2
Remove all four interior mount casting retainer screws from positions shown.
Remove top trays if necessary.
Insert Uprights into slots in mount castings.
Make sure holes in Uprights face inside.
P2
STEP 3
UPDATED AS OF: 07/14/2020 5 of 6
STEP 4
Insert base at an angle and align screw holes with those in Uprights. Insert four screws, leaving loose.
A
P3
Insert Panels from top of Upights and slide down channels.
STEP 5
UPDATED AS OF: 07/14/2020 6 of 6
STEP 6
Place Top Cap over Uprights and top edge of Panels.
Secure in place with four screws tightened into Uprights.
THIS COMPLETES ASSEMBLY INSTRUCTION
Tighten screws inserted in Step 3
then replace screws removed in
Step 1 and tighten into Uprights.
Cabinet Transaction Top
UPDATED AS OF: 05/05/2020 1 of 6
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
P1 - Transaction Top
P2 - Support Tube
x1
x4
A - #10 x 1” Wood Screw x8
Parts List
UPDATED AS OF: 05/05/2020 2 of 6
Hardware
Review full assembly instructions and
check that all parts are present before
beginning assembly. Heavy or large
furniture may require multiple persons in
order to properly assemble. If you have
questions regarding assembly, contact
the manufacturer before continuing.
Damage due to incorrect assembly may
not be covered by warranty. Do not use
product unless all screws are tight. Check
all screws for tightness at least every
six months. If parts are broken, missing,
damaged, or worn, stop use of the product
until repairs are made by your dealer using
factory authorized parts.
WARNINGS AND DISCLAIMERS
UPDATED AS OF: 05/05/2020 3 of 6
Previo a comenzar el proceso de
ensamblaje favor de revisar las
instrucciones y asegurarse que cuenta con
todas las partes y materiales necesarios.
Es posible que los muebles grandes o
pesados, requieran mas de una persona
para ensamblarlos correctamente. Por
favor contacte al fabricante directamente
si tiene alguna duda o pregunta antes de
continuar con el proceso de armado del
producto. La garantía no cubrirá daños
que ocurrieron por errores cometidos
durante el proceso de ensamblaje. Todos
los tornillos deben estar ajustados previo
el uso del producto. Debe revisar los
tornillos periódicamente, por lo menos
cada seis meses y asegurarse de que
estén bien ajustados. Por favor detenga
el uso del producto si partes del producto
se pierden, rompen, se deterioran por uso
o se rompen. Favor de contactar a su
distribuidor para que le envíen las partes
necesarias o realice las reparaciones
necesarias con partes autorizadas por el
fabricante.
Avant de commencer l’ assamblage
veuillez consulter les instructions
comptes et vérier si vous avez toutes
les pièces nécessaires. Ill est possible que
plusieurs personnes soient nécessaires
pour assemble des meubles grand ou
lourds. En cas de doute sur l assamblage
contactez le fabricant avant de continuer.
Les dommages encourus pendant
l’assamblage ne seront pas couvert par
la garantie. Ne pas utiliser le produit sans
vérier que tous les vis soient seres.
Vériez que les vis sont serrées au moins
tous le 6 mois. Si aucune pièce se casse,
manque, est endommagée ou usée,
arrêtez d’ utiliser de produit jusqu’à ce
que le vendeur le repaire a l’aide de pièces
autorisées par la fabricant.
ADVERTENCIAS Y RENUNCIAS AVERTISSEMENTS
STEP 1
UPDATED AS OF: 05/05/2020 4 of 6
STEP 2
Take out drawers if necessary. Remove casting retainer screws from positions
shown inside cabinet. Set screws aside. Repeat on other side of cabinet.
Insert Support Tubes into slots in mount castings. Replace screws removed in previous step
being careful to raise Support Tubes to equal heights when lining up screw holes. For proper
height adjustment see Support Height Addendum on page 6.
P2
P2
STEP 3
UPDATED AS OF: 05/05/2020 5 of 6
THIS COMPLETES ASSEMBLY INSTRUCTION
Using pre-drilled holes in bottom of Transaction Top as guides, secure top to supports with
wood screws driven directly into underside of top.
A
Support Height Addendum
UPDATED AS OF: 05/05/2020 6 of 6
Use the distances below while setting Support Tubes in Step 2 to ensure correct transaction
top height. Distances are provided for each of three cabinet height options and are measured
from ground to top of Support Tube.
H1: 27.75”
H2: 40.75”
H3: 53.00”
Cabinet Wardrobe Option
UPDATED AS OF: 05/05/2020 1 of 5
INSTRUCCIONES DE ENSEMBLAJE
NO LA TIRE
INSTRUCTIONS DE MONTAGE
NE PAS JETER
ASSEMBLY INSTRUCTIONS
DO NOT THROW AWAY!
P1 - Shelf
P2 - Wardrobe Hook
x1
x1
A - M6 x 12.5mm Screw
B - Shelf Clip
x1
x4
Parts List
UPDATED AS OF: 05/05/2020 2 of 5
Hardware
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23

Balt Compass Cabinet Accessory Assembly Instructions

Taper
Assembly Instructions
Ce manuel convient également à

dans d''autres langues