Chief KRA227SXRH Manuel utilisateur
- Catégorie
- Mur
- Taper
- Manuel utilisateur
KRA227 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located on the KRA227 does not exceed 25 lbs
(11.3 kg). In addition, when the KRA227 accessory is attached
to a K1 Series mount, the listed weight capacity of that
assembly becomes the weight capacity listed in Table 1.
Table 1: Weight Capacity
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
IMPORTANT ! :
The KRA227 accessory is designed to be
mounted to a K1D120, K1P120, K1S120, and K1W120 Series
mount.
--SAVE THESE INSTRUCTIONS--
MODEL
(Original
K1 Series
mount)
Max
Weight
for EACH
Display
Max Weight
Capacity of
Mounting System
with KRA227
Attached
K1D120 25 lbs
(11.34 kg) 50 lbs
(22.7 kg)
K1P120 25 lbs
(11.34 kg) 50 lbs
(22.7 kg)
K1S120 25 lbs
(11.34 kg) 50 lbs
(22.7 kg)
K1W120 25 lbs
(11.34 kg) 50 lbs
(22.7 kg)
Installation Instructions KRA227
3
DIMENSIONS
INTERFACE
ROTATION
RANGE
90
MOUNTING PATTERN
COMPATIBILITY
100 X 100
75 X 75 TILT RANGE
75
UP
10
DOWN
6.75
171.5
DYNAMIC LIT ARM
LENGTH RANGE
STRAIGHT = MAX
FULL UP/DOWN = MIN
10.21
7.12
259.3
180.9
DIMENSIONS: INCHES
[MILLIMETERS]
KRA227 (standard)
HEIGHT ADJUST
RANGE
16.75
3.75
[425.45]
[95.25]
FULL UP/DOWN =MIN
10.21
7.12
[259.3]
[180.9]
1.83
46.4
DYNAMIC LIFT ARM
LENGTH RANGE
STRAIGHT = MAX
INTERFACE ROTATION
RANGE
90
MOUNTING PATTERN
COMPATABILITY
100 X 100
75 X 75
KRA227xRH (reduced height)
KRA227 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions KRA227
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/2" 1/8" (included)
3/16" (included)
A (1)
[Single monitor arm]
B (4)
M4 x 14mm C (4)
M4 x 25mm
D (4)
M10 x M5.3 x M10
Display Mounting Hardware
E (1)
[Plastic washer]
F (1)
[Pivot point G (2)
spacer] [Stainless steel washer]
H (1)
10-24 x 1/4" J (1)
5/16-18" x 3"
K (1)
[Pivot pin]
L (1)
5/16" M (1)
1/8" N (1)
3/16"
(standard shown)
KRA227 Installation Instructions
6
ASSEMBLY AND INSTALLATION
1. Carefully remove display from existing mount, following
instructions included with mount.
2. Loosen lock nut and 3" button head cap screw located in
arm to remove arm from mount. SAVE ALL HARDWARE
AND MOUNT ARM! (See Figure 1)
Figure 1
3. Attach single monitor arm assembly (A) to original mount
base using hardware that was removed in Step 2. (See
Figure 2)
4. Reattach original mount arm (removed in Step 2) using one
5/16-18 x 3" button head cap screw (J), one plastic washer
(E), two stainless steel washers (G), one pivot pin (K), one
pivot point spacer (F), and one 5/16" lock nut (L). (See
Figure 3)
Figure 2
Figure 3
x 1
2
2
x 1
(A)
Steel
washers
Plastic
washers
3
x 1
x 1
3
4
4
(L) x 1
(J) x 1
(F)
(K)
(A)
(G) x 2
(E)
Installation Instructions KRA227
7
DISPLAY INSTALLATION
1. Remove quick release faceplate from KRA227 by pulling
quick release lever and sliding faceplate off. (See Figure 4)
Figure 4
2. Carefully place display face down on protective surface.
3. Connect faceplate to display.
For flush mounting hole installation:
•Using Phillips screwdriver, carefully install four
M4x14mm screws (B) through corresponding holes on
faceplate and into the mounting holes on the display.
(See Figure 5)
Figure 5
For recessed mounting hole installation:
•Place four spacers (D) on top of mounting holes on
back of display. (See Figure 6)
•Using Phillips screwdriver, carefully install four
M4x25mm screws (C) through corresponding holes on
faceplate, spacers (D) and into the mounting holes on
the display. (See Figure 6)
Figure 6
4. Position display with faceplate attached above KRA227.
(See Figure 7)
5. Slide faceplate onto KRA227 head until quick release tab
clicks into place. (See Figure 7)
Figure 7
Adjusting Rotation of Faceplate
The faceplate may be rotated 90° in either direction for either
landscape or portrait use.
1. (Optional) Rotational adjustment may be locked by
fastening face plate in place using one 10-24 x 1/4" button
head cap screw (H) into back of faceplate. (See Figure 8)
2. Use the 3/16" hex key (N) on the button head cap screw to
adjust rotational tension, as necessary.
Figure 8
3. Refer to Adjustments and Cable Management information
in the original mount installation instructions for further
information.
Quick release lever
1
1
KRA227
(B) x 4
quick release
faceplate
(for flush mounting holes)
3
(for recessed mounting holes)
(C) x 4
(D) x 4
quick release
faceplate
3
5
KRA227
(H)
1
KRA227 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002660 Rev01
2015 Milestone AV Technologies
www.chiefmfg.com
03/15
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief KRA227SXRH Manuel utilisateur
- Catégorie
- Mur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Chief KRA227SXRH User manual
Documents connexes
-
Chief KRA228B Le manuel du propriétaire
-
-
-
-
-
-
-
-
-