Briggs & Stratton Portable Generator 01653-4 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: Portable Generator 01653-4

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

01653-4

(3250W)

Operator’s Manual

Manuel d’utilisation

Manual del Operario

Questions? Help is just a moment away!

Vous avez des questions? Vous n'avez pas besoin

d'aller loin pour trouver de l'aide!

Preguntas? La ayuda es justa un momento lejos!

Call: Generator Helpline

Appelez: Ligne d'assistance de Générateur

Llame: Línea Directa del Generador

1-800-743-4115 M-F 8-5 CT

BRIGGSandSTRATTON.COM

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Manual No. 199972GS

Revision B (02/20/2007)

SAFETY RULES

TABLE OF CONTENTS

Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

Know Your Generator . . . . . . . . . . . . . . . . . . . . . . . . . 5

Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

EQUIPMENT DESCRIPTION

Read this manual carefully and become

familiar with your generator. Know its

applications, its limitations and any hazards

involved.

The generator is an engine–driven, revolving field,

alternating current (AC) generator. It was designed to

supply electrical power for operating compatible

electrical lighting, appliances, tools and motor loads.

The generator’s revolving field is driven at about

3,600 rpm by a single-cylinder engine.

CAUTION! DO NOT exceed the generator’s

wattage/amperage capacity. See “Don’t Overload

Generator”.

Every effort has been made to ensure that information

in this manual is accurate and current. However, we

reserve the right to change, alter or otherwise improve

the product and this document at any time without

prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources

Board. For warranty information refer to the engine

operator’s manual.

SAFETY RULES

This is the safety alert symbol. It is used to

alert you to potential personal injury

hazards. Obey all safety messages that

follow this symbol to avoid possible injury

or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a

safety message to alert you to hazards. DANGER

indicates a hazard which, if not avoided, will result in

death or serious injury. WARNING indicates a hazard

which, if not avoided, could result in death or serious

injury. CAUTION indicates a hazard which, if not

avoided, might result in minor or moderate injury.

CAUTION, when used without the alert symbol,

indicates a situation that could result in equipment

damage. Follow safety messages to avoid or reduce

the risk of injury or death.

Hazard Symbols and Meanings

The engine exhaust from this product contains

chemicals known to the State of California to cause

cancer, birth defects, or other reproductive harm.

WARNING

material may be reproduced or transmitted in any form

by any means without the express written permission

of Briggs & Stratton Power Products Group, LLC.

SAVE THESE INSTRUCTIONS

Fire

Explosion

Toxic Fumes

Hot Surface

Electrical Shock

Kickback

Operator’s Manual

SAFETY RULES

• This generator does not meet U. S. Coast Guard

Regulation 33CFR-183 and should not be used on

marine applications.

• Failure to use the appropriate U. S. Coast Guard

approved generator could result in death or serious injury

and/or property damage.

WARNING

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or

enclosure (even if doors or windows are open), including

the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting or death.

WARNING

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• Wait for spilled fuel to evaporate before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• This generator is not for use in mobile equipment or

marine applications.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN

TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers or other appliances that have pilot light or other

ignition source because they can ignite fuel vapors.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

SAFETY RULES

• DO NOT tamper with governed speed. Generator

supplies correct rated frequency and voltage when

running at governed speed.

• DO NOT modify generator in any way.

Excessively high operating speeds increase risk of

injury and damage to generator.

Excessively low speeds impose a heavy load.

CAUTION

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON

for operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices

connected to it.

CAUTION

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

call 1-800-743-4115.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust

gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of

generator including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks,

Forests, and Public Property require equipment powered

by an internal combustion engine to have a spark

arrester, maintained in effective working order, complying

to USDA Forest service standard 5100-1C or later

revision. In the State of California a spark arrester is

required under section 4442 of the California Public

resources code. Other states may have similar laws.

Running engines produce heat. Temperature

of muffler and nearby areas can reach or

exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

FEATURES AND CONTROLS

120 Volt AC, 20 Amp Duplex Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 20 Amp, single phase, 60 Hz electrical

lighting, appliance, tool and motor loads.

120 Volt AC, 30 Amp Locking Receptacle — May be

used to supply electrical power for the operation of

120 Volt AC, 30 Amp, single phase, 60 Hz electrical

lighting, appliance, tool and motor loads.

Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

Choke Lever — Used when starting a cold engine.

Circuit Breakers (AC) — Each receptacle is provided

with a push-to-reset circuit breaker to protect the

generator against electrical overload.

Data Tag – Provides model, revision and serial

number of generator. Please have these readily

available if calling for assistance.

Fuel Tank — Capacity of one U.S. gallon.

Grounding Fastener — Consult your local agency

having jurisdiction for grounding requirements in your

area.

Recoil Starter — Used to start the engine.

Rocker Switch — Set this switch to "On" before using

recoil starter. Set switch to "Off" to switch OFF engine.

KNOW YOUR GENERATOR

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

Circuit Breakers (AC)

Fuel Tank

120 Volt AC, 30 Amp

Locking Receptacle

120 Volt AC, 20 Amp

Duplex Receptacle

Grounding Fastener

Choke Lever

Air Cleaner

Recoil Starter

Rocker Switch

Data Tag

ASSEMBLY

Your generator requires some assembly and is ready

for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your

generator, please call the generator helpline at

1-800-743-4115. If calling for assistance, please have the

model, revision, and serial number from the data tag

available.

Unpacking the Generator

1. Set the carton on a rigid flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner

from top to bottom.

4. Leave generator on carton to install wheel kit.

Install Wheel Kit

The wheel kit is designed to greatly improve the

portability of your generator.

NOTE: Wheel kit is not intended for over-the-road use.

To install wheel kit you need the following tools:

• 15/16" (22mm) box, open end, or socket wrench

• Two 13mm box, open end, or socket wrenches

• Two 10mm box, open end, or socket wrenches

Install Wheel Kit as follows: (Refer to Figure 1)

1. Tip generator so that engine end is up.

2. Place axle stud through mounting bracket on

generator frame.

3. Use 15/16” wrench to secure the axle stud to

frame with 5/8-18 jam nut.

4. Place wheel on axle stud.

NOTE: Be sure to install wheel with raised hub inboard.

5. Place flat washer over axle stud and fasten with

retaining pin.

6. Repeat steps 2 through 5 for other wheel.

7. Tip generator so that engine side is down.

8. Attach the vibration mount to the support leg with

a M6 X 16mm capscrew and M6 hex nut.

9. Remove two top nuts from vibration mount on unit

with 13mm wrench. Use these nuts to attach the

support leg.

Capscrew

Handle

Grip

Nut

Mounting Leg

Use Existing Fasteners

to Secure Leg

Jam Nut

Retaining Pin

Wheel

Washer

Axle Stud

Figure 1 — Installing the Wheel Kit

Capscrew

Vibration Mount

Nut

ASSEMBLY

10. Center handle on top of support leg end of

generator frame.

11. Attach handle using two 13mm wrenches with two

M8 X 45mm capscrews and two M8 lock nuts.

12. Return generator to normal operating position

(resting on wheels and support leg).

BEFORE STARTING THE

ENGINE

Add Engine Oil

• Place generator on a level surface.

• Refer to engine operator’s manual and follow oil

recommendations and instructions.

NOTE: Check oil often during engine break–in. Refer

to engine owner’s manual for recommendations.

NOTE: The alternator assembly rotates on a

prelubricated and sealed ball bearing that requires no

additional lubrication for the life of the bearing.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

To protect the fuel system from gum formation, mix in

a fuel stabilizer when adding fuel. See Storage. All fuel

is not the same. If you experience starting or

performance problems after using fuel, switch to a

different fuel provider or change brands. This engine is

certified to operate on gasoline. The emission control

system for this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel to fuel tank. Be

careful not to overfill. Allow about 1.5" of tank

space for fuel expansion (Figure 3).

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At higher altitudes (over 5,000 feet), 85 octane/85 AKI

(89 RON) gasoline is recommended. High-altitude use

may require a carburetor jet kit to improve performance

and decrease fuel consumption. See an Authorized

Briggs & Stratton Dealer for more information.

Fuel

Tank

1.5” Air Space

Figure 2 - Fuel Expansion

CAUTION

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in fuel.

• DO NOT modify engine to run on alternate fuels.

Avoid generator damage.

Failure to follow Operator’s Manual for fuel

reccomendations voids warranty.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• DO NOT light a cigarette or smoke.

Fuel and its vapors are extremely flammable

and explosive.

Fire or explosion can cause severe burns or

death.

WARNING

CAUTION

• Refer to engine operator’s manual for oil fill information.

• Damage to equipment resulting from failure to follow

this instruction will void warranty.

Any attempt to crank or start the engine before it has

been properly filled with the recommended oil will

result in equipment failure.

OPERATION

USING THE GENERATOR

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals

on the AC output receptacles. The system ground is

connected to the AC neutral wire (see “Equipment

Description”, earlier in this manual).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the

generator. Please consult a qualified electrician, electrical

inspector, or the local agency having jurisdiction.

• In some areas, generators are required to be

registered with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be observed.

Connecting to a Building’s Electrical

System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician. The

connection must isolate the generator power from

utility power, and must comply with all applicable laws

and electrical codes.

Generator Location

Generator Clearance

Place generator in a well ventilated area, which will

allow for removal of deadly exhaust gas. DO NOT place

generator where exhaust gas could accumulate and

enter inside or be drawn into a potentially occupied

building. Ensure exhaust gas is kept away from any

windows, doors, ventilation intakes or other openings

that can allow exhaust gas to collect in a confined area

(Figure 4). Prevailing winds and air currents should be

taken into consideration when positioning generator.

• When using generator for backup power, notify utility

company. Use approved transfer equipment to isolate

generator from electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp

or highly conductive area, such as metal decking or steel

work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

Generator produces powerful voltage.

Failure to isolate generator from power utility

can result in death or injury to electric utility

workers due to backfeed of electrical energy.

WARNING

Figure 4 — Generator Clearance

Exhaust Port

Typical Generator Shown

• Keep at least 5 ft. (152 cm) clearance on all sides of

generator including overhead.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

OPERATING THE

GENERATOR

Starting the Engine

Disconnect all electrical loads from the generator. Use

the following start instructions:

1. Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a

level surface will cause the unit not to start or shut

down during operation.

2. Turn fuel valve to “On” position (Figure 4).

3. Start engine according to instructions given in

engine operator’s manual.

NOTE: If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on

a level surface and check for proper oil level in

crankcase. This unit may be equipped with a low oil

protection device. See engine operator’s manual.

Connecting Electrical Loads

• Let engine stabilize and warm up for a few minutes

after starting.

• Plug in and turn on the desired 120 Volt AC, single

phase, 60 Hz electrical loads.

• DO NOT connect 240 Volt loads to the 120 Volt

duplex receptacles.

• DO NOT connect 3–phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

“Don’t Overload Generator”.

Fuel Valve is

shown in the

On position

Figure 4 — Fuel Valve

• See “Don’t Overload Generator”.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON

for operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices

connected to it.

CAUTION

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

Rapid retraction of starter cord (kickback)

will pull hand and arm toward engine faster

than you can let go.

Broken bones, fractures, bruises or sprains

could result.

WARNING

• DO NOT touch hot surfaces and avoid hot exhaust

gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of

generator including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks,

Forests, and Public Property require equipment powered

by an internal combustion engine to have a spark

arrester, maintained in effective working order, complying

to USDA Forest service standard 5100-1C or later

revision. In the State of California a spark arrester is

required under section 4442 of the California Public

resources code. Other states may have similar laws.

Running engines produce heat. Temperature

of muffler and nearby areas can reach or

exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

OPERATION

Stopping the Engine

1. Turn OFF and unplug all electrical loads from

generator panel receptacles. NEVER start or stop

engine with electrical devices plugged in and

turned ON.

2. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and

generator.

3. Turn engine off according to instructions given in

the engine operator’s manual.

4. Move fuel valve to “Off” position.

RECEPTACLES

120 Volt AC, 30 Amp Locking

Receptacle

Use a NEMA L5-30 plug with this receptacle. Connect

a 3-wire cord set rated for 125 Volts AC at 30 Amps to

the plug (Figure 5).

Use this receptacle to operate 120 Volt AC, 60 Hz,

single phase loads requiring up to 3,250 watts

(3.25 kW) of power at 27.1 Amps. The outlet is

protected by a push-to-reset circuit breaker.

120 Volt AC, 20 Amp, Duplex

Receptacles

Each duplex receptacle (Figure 6) is protected against

overload by a push–to–reset circuit breaker.

Use each receptacle to operate 120 Volt AC,

single–phase, 60 Hz electrical loads requiring up to

2,400 watts (2.4 kW) at 20 Amps of current. Use cord

sets that are rated for 125 Volt AC loads at 20 Amps

(or greater).

COLD WEATHER

OPERATION

Under certain weather conditions (temperatures below

40°F [4°C] combined with high humidity), your

generator may experience icing of the carburetor

and/or the crankcase breather system. To reduce this

problem, you need to perform the following:

1. Make sure generator has clean, fresh fuel.

2. Open fuel valve (turn valve to open position).

3. Use SAE 5W-30 oil (see engine operator’s

manual).

4. Check oil level daily or after every eight (8) hours

of operation.

5. Maintain generator following “Maintenance

Schedule” in engine operator’s manual.

6. Shelter unit from elements.

Figure 6 — 120 Volt, 20 Amp Duplex Receptacle

Figure 5 — 120 Volt AC, 30 Amp, Locking Receptacle

3-Wire Cord Set

Neutral

120V

Hot

Ground (Green)

NEMA L5-30

• NEVER attempt to power a device requiring more

amperage than generator or receptacle can supply.

• DO NOT overload the generator. See “Don’t Overload

Generator”.

Receptacles may be marked with rating value

greater than generator output capacity.

CAUTION

OPERATION

Creating a Temporary Cold Weather

Shelter

1. In an emergency, use the original shipping carton.

2. Cut off top carton flaps and one long side of carton

to expose muffler side of unit. If required, tape up

other sides of carton to fit over generator as shown

in Figure 7.

NOTE: If required, remove wheel kit to fit carton over

generator as shown in Figure 7.

3. Cut appropriate slots to access receptacles of unit.

4. Face exposed end away from wind and elements.

5. Locate generator as described in the section

“Generator Location”. Keep exhaust gas from

entering a confined area through windows, doors,

ventilation intakes or other openings.

6. Start generator as described in the section

“Starting the Engine”, then place carton over

generator. Keep at least 5 ft. (152 cm) clearance

on all sides of generator including overhead with

shelter in place.

7. Remove shelter when temperatures are above

40°F [4°C].

8. Turn engine OFF and let cool two (2) minutes

before refueling. Let any spilled fuel evaporate

before starting engine.

Creating a Permanent Cold Weather

Shelter

1. Build a structure that will enclose three sides and

the top of the generator, making sure muffler side

of generator is exposed.

NOTE: Structure should hold enough heat created by

the generator to prevent icing problem.

2. DO NOT enclose generator any more than shown

in Figure 7.

NOTE: If a wheel kit is installed on the generator,

enlarge shelter accordingly.

3. Follow steps 3 through 8 as described previously

in “Creating a Temporary Cold Weather Shelter”.

Figure 7 — Permanent Cold Weather Shelter

Wind

• DO NOT touch hot surfaces and avoid hot exhaust

gases.

• Allow equipment to cool before touching.

• Keep at least 5 ft. (152 cm) clearance on all sides of

generator including overhead.

• Remove shelter when temperatures are above 40°F [4°C].

Running engines produce heat. Temperature

of muffler and nearby areas can reach or

exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

WARNING

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes or other openings.

• DO NOT operate generator inside any building or

enclosure (even if doors or windows are open), including

the generator compartment of a recreational vehicle (RV).

Running generator gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause

nausea, fainting or death.

WARNING

OPERATION

DON'T OVERLOAD

GENERATOR

Capacity

You must make sure your generator can supply

enough rated (running) and surge (starting) watts for

the items you will power at the same time. Follow

these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This

is the amount of power your generator must

produce to keep your items running. See Figure 8.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time,

total surge watts can be estimated by adding only

the item(s) with the highest additional surge watts

to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached

devices, it is important to take care when adding

electrical loads to your generator. There should be

nothing connected to the generator outlets before

starting it's engine. The correct and safe way to manage

generator power is to sequentially add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the

largest load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly.

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.

Take special care to consider surge loads in generator

capacity, as described above.

*Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 -

Light (75 Watts) 75 -

3075 Total

Running Watts

1800 Highest

Surge Watts

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt

Deep Freezer

500

Sump Pump

800

1200

Refrigerator/Freezer - 18 Cu. Ft.

800

1600

Water Well Pump - 1/3 HP

1000

2000

Heating/Cooling

Window AC - 10,000 BTU

1200

1800

Window Fan

300

600

Furnace Fan Blower - 1/2 HP

800

1300

Kitchen

Microwave Oven - 1000 Watt

1000

Coffee Maker

1500

Electric Stove - Single Element

1500

Hot Plate

2500

Family Room

DVD/CD Player

100

VCR

100

Stereo Receiver

450

Color Television - 27”

500

Personal Computer w/17” monitor

800

Other

Security System

180

AM/FM Clock Radio

300

Garage Door Opener - 1/2 HP

480

520

Electric Water Heater - 40 Gallon

4000

DIY/Job Site

Quartz Halogen Work Light

1000

Airless Sprayer - 1/3 HP

600

1200

Reciprocating Saw

960

Electric Drill - 1/2 HP

1000

Circular Saw - 7 1/4”

1500

Miter Saw - 10”

1800

Table Planer - 6”

1800

Table Saw/Radial Arm Saw - 10”

2000

Air Compressor - 1-1/2 HP

2500

Figure 8 - Wattage Reference Chart

SPECIFICATIONS AND MAINTENANCE

SPECIFICATIONS

Starting Wattage . . . . . . . . . . . . . . . . . .4,550 watts

Wattage . . . . . . . . . . . . . . . . . . . . . . . . .3,250 watts

120 Volt AC Load Current . . . . . . . . . . . .27.1 Amps

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–phase

Rated Frequency . . . . . . . . . . . . . . . . . . . .60 Hertz

Fuel Tank Capacity. . . . . . . . . . . . . . . 1 U.S. gallons

Shipping Weight. . . . . . . . . . . . . . . . . . . . . . 102 lbs.

GENERAL MAINTENANCE

RECOMMENDATIONS

The Owner/Operator is responsible for making sure

that all periodic maintenance tasks are completed on a

timely basis; that all discrepancies are corrected; and

that the unit is kept clean and properly stored. NEVER

operate a damaged or defective generator.

NOTE: Should you have questions about replacing

components on your Briggs & Stratton Power Products

generator, please call 1-800-743-4115 for assistance.

Engine Maintenance

See engine operator’s manual for instructions.

KEEP OUT OF REACH OF CHILDREN.

DON'T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

Generator Maintenance

Generator maintenance consists of keeping the unit

clean and dry. Operate and store the unit in a clean

dry environment where it will not be exposed to

excessive dust, dirt, moisture or any corrosive vapors.

Cooling air slots in the generator must not become

clogged with snow, leaves or any other foreign

material.

NOTE: DO NOT use a garden hose to clean

generator. Water can enter engine fuel system and

cause problems. In addition, if water enters generator

through cooling air slots, some of the water will be

retained in voids and cracks of the rotor and stator

winding insulation. Water and dirt buildup on the

generator internal windings will eventually decrease

the insulation resistance of these windings.

Generator Cleaning

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt or

oil.

• Use a vacuum cleaner to pick up loose dirt and

debris.

• Inspect cooling air slots and opening on generator.

These openings must be kept clean and

unobstructed.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

Avoid prolonged or repeated skin contact with used

motor oil.

CAUTION

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

Improper treatment of generator can damage it and

shorten its life.

CAUTION

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Unintentional sparking can result in fire or

electric shock.

WARNING

STORAGE

The generator should be started at least once every

seven days and allowed to run at least 30 minutes. If

this cannot be done and you must store the unit for

more than 30 days, use the following guidelines to

prepare it for storage.

Generator Storage

• Clean the generator as outlined in “Generator

Cleaning”.

• Check that cooling air slots and openings on

generator are open and unobstructed.

Engine Storage

See engine operator’s manual for instructions.

Other Storage Tips

• To prevent gum from forming in fuel system or on

essential carburetor parts, add fuel stabilizer into fuel

tank and fill with fresh fuel. Run the unit for several

minutes to circulate the additive through the

carburetor. The unit and fuel can then be stored for

up to 24 months. Fuel stabilizer can be purchased

locally.

• DO NOT store fuel from one season to another

unless it has been treated as described above.

• Replace fuel container if it starts to rust. Rust and/or

dirt in fuel can cause problems if it's used with this

unit.

• Store unit in a clean and dry area.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the

cover on the equipment.

Storage covers can be flammable.

WARNING

TROUBLESHOOTING

Problem Cause Correction

No AC output is available, but

generator is running.

1. One of the circuit breakers is

open.

2. Fault in generator.

3. Poor connection or defective

cord set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact Authorized service

facility.

3. Check and repair.

4. Connect another device that is

in good condition.

Generator runs good at no-load

but "bogs" down" when loads are

connected.

1. Short circuit in a connected

load.

2. Generator is overloaded.

3. Shorted generator circuit.

1. Disconnect shorted electrical

load.

2. See "Don't Overload Generator".

3. Contact Authorized service

facility.

Generator will not start; or starts

and runs rough.

Low oil level. Fill crankcase to proper level or

place generator on level surface.

Generator shuts down during

operation.

1. Out of fuel.

2. Low oil level.

1. Fill fuel tank.

2. Fill crankcase to proper level or

place generator on level surface.

Generator lacks power. Load is too high. See "Don't Overload Generator".

NOTES

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC PORTABLE GENERATOR OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the portable generator that is

defective in material or workmanship or both. Transportation charges on product submitted for repair or replacement under this

warranty must be borne by purchaser. This warranty is effective for the time periods and subject to the conditions stated below.

For warranty service, find the nearest Authorized Service Dealer in our dealer locator map at BRIGGSandSTRATTON.com.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT

PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW. Some states or

countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty

gives you specific legal rights and you may also have other rights which vary from state to state or country to country.

2 years*

1 year

Consumer Use

Commercial Use

The warranty period begins on the date of purchase by the first retail end user, and continues for the period of time stated above.

“Consumer Use" means personal residential household use by a retail consumer. “Commercial Use" means all other uses, including

use for commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be

considered as commercial use for purposes of this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR

PROOF OF PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME

WARRANTY SERVICE IS REQUESTED, THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE

WARRANTY PERIOD.

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty

repairs. Most warranty repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For

example, warranty service would not apply if equipment damage occurred because of misuse, lack of routine maintenance, shipping,

handling, warehousing or improper installation. Similarly, the warranty is void if the manufacturing date or the serial number on the

portable generator has been removed or the equipment has been altered or modified. During the warranty period, the Authorized

Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal use and

service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This

warranty does not cover repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or

unauthorized installation or alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper

maintenance, repair or storage so as, in our judgment, to adversely affect its performance and reliability. This warranty also

does not cover normal maintenance such as air filters, adjustments, fuel system cleaning and obstruction (due to chemical,

dirt, carbon, lime, and so forth).

• Other Exclusions: This warranty excludes wear items such as o-rings, filters, etc., or malfunctions resulting from accidents,

abuse, modifications, alterations, or improper servicing or freezing or chemical deterioration. Accessory parts such as starting

batteries, generator adapter cord sets and storage covers are excluded from the product warranty. This warranty excludes used,

reconditioned, and demonstration equipment, equipment used for prime power in place of utility power, equipment used in life

support applications, and failures due to acts of God and other force majeure events beyond the manufacturers control.

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

Effective February 1, 2006 replaces all undated Warranties and all Warranties dated before February 1, 2006

198189E, Rev. A, 7/14/2006

*Second year parts only

WARRANTY PERIOD

RÈGLES DE SÉCURITÉ

TABLE DES MATIÈRES

Règles de Sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-20

Connaissez Votre Générateur . . . . . . . . . . . . . . . . . . . . . . 21

Assemblage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22-23

Opération . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24-28

Entretien. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Rangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Remarques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

DESCRIPTION DE L ÉQUIPEMENT

Lisez avec soin ce manuel et familiarisez-vous

avec votre générateur. Connaissez ses

applications, ses limitations et les dangers qu'il

implique.

Ce générateur est un générateur entraîné par un moteur à

champ magnétique rotatif produisant du courant alternatif

(c.a.). Il a été conçu pour fournir du courant électrique pour

faire marcher des charges compatibles d'éclairage,

d'appareils ménagers, d'outil et de moteur. Le champ

tournant du générateur est entraîné à 3,600 T/M par un

moteur monocylindrique.

ATTENTION! NE PAS dépasser la capacité en watts ou en

Ampères du générateur. Voir "Ne Pas Surcharger le

Générateur" pour l'information spécifique.

Tout a été mis en oeuvre pour que les informations

contenues dans ce manuel soient exactes et à jour.

Cependant, nous se réserve le droit de changer, d'altérer ou

d'améliorer le produit à n'importe quel moment sans avis

préalable.

Le Système de contrôle de l'émission du générateur est garanti

pour des normes établies par L'Agence de protection de

l'environnement et le California Air Resources Board. Pour des

informations sur la garantie, se reporter au manuel d'utilisation

du moteur.

RÈGLES DE SÉCURITÉ

Ceci est la sûreté le symbole vif. Il est utilisé pour

vous alerter aux dangers de blessure personnels

potentiels. Obéir tous messages de sûreté qui

suivent ce symbole éviter la blessure ou la mort

possibles.

Le symbole indiquant un message de sécurité est

accompagné d'un mot indicateur (DANGER, ATTENTION,

AVERTISSEMENT), d'un message illustré et/ou d'un

message de sécurité visant à vous avertir des dangers.

DANGER indique un danger qui, s'il n'est pas évité,

provoquera des blessures graves, voire fatales.

AVERTISSEMENT indique un danger qui, s'il n'est pas évité,

peut provoquer des blessures graves, voire fatales.

ATTENTION indique un danger qui, s'il n'est pas évité, peut

provoquer des blessures mineures ou légères. Le mot

ATTENTION, lorsqu'il est utilisé sans le symbole d'alerte,

indique une situation pouvant endommager l'équipement.

Suivez les messages de sécurité pour éviter ou réduire les

risques de blessures ou de mort.

Symboles de Danger et Moyens

L’échappement du moteur de ce produit contient des produits

chimiques que l’État de Californie considère comme causant

le cancer, des déformations à la naissance ou d’autres

dangers concernant la reproduction.

AVERTISSEMENT

VEUILLEZ CONSERVER CES INSTRUCTIONS

Feu

Explosion

Emanations Toxiques

Surface Chaude

Choc Électrique

Recul

Manuel d'Utilisation

RÈGLES DE SÉCURITÉ

• Faites fonctionner le générateur SEULEMENT à l'extérieur.

• Installez un avertisseur de monoxyde de carbone à piles près

des chambres à coucher.

• Évitez que les gaz d'échappement entrent dans un espace

restreint, par une fenêtre, une porte, une prise d'aération ou toute

autre ouverture.

• Ne faites pas fonctionner le générateur à l'intérieur d'un bâtiment

ou d'un abri (même si les fenêtres et les portes sont ouvertes), y

compris à l'intérieur du compartiment d'un véhicule de plaisance.

Le générateur, lorsqu'il fonctionne, produit du

monoxyde de carbone, un gaz toxique inodore et

incolore.

Le fait de respirer du monoxyde de carbone

provoque des nausées, des évanouissements ou

peut être fatal.

AVERTISSEMENT

• Cette génératrice ne satisfait pas aux normes U. S. Coast Guard

Regulation 33CFR-183 et ne doit pas être utilisée pour des

applications marines.

• L'omission d'utiliser une génératrice appropriée et approuvée

par U. S. Coast Guard pourrait entraîner des blessures

corporelles ou des dommages matériels.

AVERTISSEMENT

LORS DE L'AJOUT OU DE LA VIDANGE DU

CARBURANT

• Éteignez le générateur et laissez-le refroidir au moins 2 minutes

avant de retirer le capuchon du réservoir de carburant. Desserrez

lentement le capuchon pour laisser la pression s'échapper du

réservoir.

• Remplissez ou vidangez le réservoir d'essence à l'extérieur.

• NE REMPLISSEZ PAS trop le réservoir. Laissez l'expansion de

l'essence.

• Attend le carburant renversé pour s'évaporer avant de démarrer

le moteur.

• Éloignez l'essence des étincelles, des flammes, des veilleuses,

de la chaleur et de toute autre source d'inflammation.

• N'ALLUMEZ PAS de cigarette ou ne fumez pas à proximité de

l'appareil.

LORS DU DÉMARRAGE DE L'ÉQUIPEMENT

• Assurez-vous que la bougie d'allumage, le silencieux, le

bouchon à essence et le filtre à air sont en place.

• NE démarrez PAS le moteur lorsque la bougie d'allumage est

enlevée.

LORSQUE L'ÉQUIPEMENT FONCTIONNE

• NE penchez PAS le moteur ou l'équipement, vous risqueriez de

renverser de l'essence.

• Cette génératrice n'est pas conçue pour être utilisée dans de

l'équipement mobile ou les applications marines.

LORSQUE VOUS TRANSPORTEZ OU RÉPAREZ

L'ÉQUIPEMENT

• Le réservoir d'essence doit être VIDE ou le robinet d'arrêt de

carburant doit être à la position fermée (OFF) pendant le

transport ou la réparation.

• Débranchez le câble de bougie.

LORSQUE VOUS ENTREPOSEZ L'ESSENCE OU UN

ÉQUIPEMENT AVEC UN RÉSERVOIR À ESSENCE

• Entreposez-le loin des appareils de chauffage, des fours, des

chauffe-eau, des sécheuses ou de tout autre appareil

électroménager disposant d'une veilleuse ou de toute autre source

d'inflammation risquant d'enflammer les vapeurs d'essence.

L'essence et ses vapeurs sont extrêmement

inflammables et explosives.

Le feu ou l'explosion risque de provoquer des

blessures graves, pouvant être fatales.

AVERTISSEMENT

• Lors du démarrage du moteur, tirez lentement sur la corde

jusqu'à ce que vous sentiez une résistance et tirez alors

rapidement afin d'éviter un effet de recul.

• NE démarrez JAMAIS ni n'arrêtez jamais le moteur alors que

des appareils électriques y sont branchés et en fonction.

Une rétroaction rapide de la corde du démarreur

(effet de recul) tirera votre main et votre bras vers

le moteur plus rapidement que vous ne pouvez

relâcher la corde.

Vous risquez ainsi de subir des fractures, des

ecchymoses ou des entorses.

AVERTISSEMENT

• Lorsque vous utilisez le générateur comme source d'énergie de

secours, il est nécessaire d'aviser les services publics d'électricité.

• Utilisez un disjoncteur différentiel lorsque vous utilisez l'appareil

dans des endroits humides ou extrêmement conductibles,

comme les terrasses en métal ou les ouvrages métalliques.

• NE touchez pas les fils dénudés ou les boîtiers.

• N'UTILISEZ pas le générateur avec des cordons électriques usés,

effilochés ou dénudés, ou abîmés de quelque sorte que ce soit.

• N'UTILISEZ pas le générateur sous la pluie.

• NE manipulez pas le générateur ou les cordons d'alimentation

lorsque vous êtes debout dans l'eau, pieds nus ou avec les

mains ou les pieds humides.

• NE laissez pas des personnes non qualifiées ou des enfants se

servir ou réparer le générateur.

Le générateur produit une tension élevée.

NE PAS isoler le générateur de l'installation

électrique risque de provoquer des blessures ou

même d'être fatal pour les ouvriers électriciens et

de causer des dommages au générateur dus à

un "backfeed" d'énergie électrique.

AVERTISSEMENT

RÈGLES DE SÉCURITÉ

• NE TRAFIQUEZ PAS la vitesse régulée. Le générateur produit

une fréquence nominale et une tension correctes lorsqu'il

fonctionne à une vitesse régulée.

• NE modifiez le générateur d'aucune façon.

Les vitesses de fonctionnement excessivement élevées

augmentent les risques de blessure ou risquent

d'endommager le générateur.

Les vitesses extrêmement lentes entraînent une charge

importante.

ATTENTION

• Voir la section " Ne Pas Surcharger Générateur ".

• Démarrez le générateur et laissez le moteur se stabiliser avant

de brancher les charges électriques.

• Branchez les charges électriques en position ARRÊT, puis,

remettez en position MARCHE.

• Éteignez les charges électriques et débranchez-les du

générateur avant de l'arrêter.

Dépasser la capacité de puissance ou d'ampérage du

générateur risque d'endommager ce dernier et/ou les

autres appareils électriques qui y sont branchés.

ATTENTION

• NE vous servez du générateur que pour les utilisations prévues.

• Si vous avez des questions concernant les utilisations prévues,

demandez à votre distributeur ou appelez 1-800-743-4115.

• Ne faites fonctionner le générateur que sur des surfaces

horizontales.

• N'EXPOSEZ pas le générateur à une humidité excessive, à de

la poussière, à de la saleté ou à des vapeurs corrosives.

• N'INSÉREZ aucun objet dans les fentes de refroidissement.

• Si les appareils branchés sont en surchauffe, éteignez-les et

débranchez-les du générateur.

• Arrêtez le générateur si :

-la puissance électrique est inexistante;

-l'équipement produit des étincelles, de la fumée ou des

flammes;

-l'unité vibre excessivement.

Un traitement inapproprié du générateur risque de

l'endommager et de raccourcir sa durée d'utilisation.

ATTENTION

LORSQUE VOUS RÉGLEZ OU RÉPAREZ VOTRE

GÉNÉRATEUR

• Débranchez toujours le câble de bougie et placez-le de façon à

ce qu'il ne soit pas en contact avec la bougie.

LORS DE TESTS D'ALLUMAGE DU MOTEUR

• Utilisez un vérificateur de bougies d'allumage approuvé.

• NE vérifiez PAS l'allumage lorsque la bougie d'allumage est

enlevée.

Unintentional peut résulter dans feu ou

électrique.

AVERTISSEMENT

• NE touchez PAS aux pièces chaudes et évitez le contact avec

les gaz d’échappement.

• Laissez l'équipement refroidir avant de le toucher.

• Laissez un dégagement d’au moins 1,52 m (5 pi) tout autour de

la génératrice, y compris au-dessus.

• Le Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property exige que de l’équipement alimenté par un moteur

à combustion interne soit doté d’un pare-étincelles et

constamment maintenu en bon état fonctionnement,

conformément à la norme de service 5100-1C de la USDA Forest

ou à une révision de celle-ci. Dans l’État de la Californie, un pare-

étincelles est requis en vertu de la section 4442 du California

Public Resources Code. Il se peut que d’autres États aient des

lois semblables.aux terres fédérales. Si vous équipez le silencieux

d'un pare-étincelles, il doit être en bon état de fonctionnement.

Les moteurs en fonctionnement produisent de la

chaleur. La température du silencieux et des

endroits à proximité peuvent atteindre, voire

dépasser 150°F (65°C).

Le contact de ces pièces risque de causer de

graves brûlures.

La chaleur et les gaz d’échappement peuvent

enflammer des matériaux combustibles et les

structures ainsi que causer des dommages au

réservoir d’essence et entraîner un incendie.

AVERTISSEMENT

La page charge ...

Briggs & Stratton Portable Generator 01653-4 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: Portable Generator 01653-4

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton Portable Generator 01653-4 User manual
español: Briggs & Stratton Portable Generator 01653-4 Manual de usuario

Briggs & Stratton Portable Generator 01653-4 Manuel utilisateur

Ce manuel convient également à

Briggs & Stratton Portable Generator 01653-4 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents