Generac XP8000E 0057081 Manuel utilisateur

Marque: Generac

Modèle: XP8000E 0057081

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Owner’s

Manual

• SAFETY

• ASSEMBLY

• OPERATION

• TROUBLESHOOTING

• WARRANTY

XP Professional Series

Portable Generator

COMMERCIAL • INDUSTRIAL • RESIDENTIAL

MODEL: 005708-1 XP8000E

8,000 Watt Portable Generator

AUTHORIZED DEALER SUPPORT:

Table of Contents

Portable Generator System

Introduction ............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ...........................................................1

Standards Index .............................................................3

Section 1 – General Information ............................. 4

1.1 Unpacking ......................................................................4

1.1.1 Accessory Box ..................................................4

1.2 Assembly .......................................................................4

1.2.1 Assembling the Wheel Kit ..................................4

1.2.2 Battery Connection ............................................4

Section 2 – Operation ............................................. 5

2.1 Know the Generator .......................................................5

2.2 Hourmeter ......................................................................6

2.3 Cord Sets and Connection Plugs ....................................6

2.3.1 120 VAC, 20 Amp, GFCI Duplex Receptacle .......6

2.3.2 120/240 VAC, 30 Amp, Receptacle ....................6

2.4 How to Use the Generator ..............................................6

2.4.1 System Ground ..................................................6

2.4.2 Grounding the Generator ....................................7

2.4.3 Connecting Electrical Loads ...............................7

2.5 Don’t Overload the Generator ..........................................7

2.6 Wattage Reference Guide ...............................................8

2.7 Before Starting the Generator .........................................8

2.7.1 Adding Engine Oil ..............................................8

2.7.2 Adding Gasoline .................................................9

2.8 To Start the Engine .........................................................9

2.9 Stopping the Engine .....................................................10

2.10 Low Oil Pressure Shutdown System .............................10

2.10.1 Initial Start-up ..................................................10

2.10.2 Sensing Low Oil Pressure ................................10

2.10.3 Restarting ........................................................10

2.11 Charging a Battery .......................................................10

Section 3 – Maintenance ...................................... 11

3.1 Maintenance Schedule .................................................11

3.2 Product Specifications ..................................................11

3.2.1 Generator Specifications ..................................11

3.2.2 Engine Specifications .......................................11

3.3 General Recommendations ...........................................11

3.3.1 Generator Maintenance ....................................11

3.3.2 To Clean the Generator .....................................11

3.3.3 Engine Maintenance .........................................12

3.3.4 Checking Oil Level ...........................................12

3.3.5 Changing the Oil and Oil Filter ..........................12

3.3.6 Replacing the Spark Plug .................................12

3.4 Service Air Cleaner .......................................................12

3.5 Clean Spark Arrestor Screen.........................................13

3.6 Adjusting Valve Clearance ............................................13

3.7 General .......................................................................14

3.8 Long Term Storage .......................................................14

3.9 Other Storage Tips .......................................................15

Section 4 – Battery Service .................................. 15

4.1 Battery Service (Replacement) .....................................15

Section 5 – Troubleshooting ................................. 16

5.1 Troubleshooting Guide ..................................................16

Section 6 – Notes ................................................. 17

Section 7 – Warranty ............................................ 16

Manual del propietario ......................................... 21

Manuel d'entretien ................................................ 43

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

Become familiar with and strictly adhere to all local, state and •

national codes and regulations.

Study all safety warnings in this manual and on the product •

carefully.

Become familiar with this manual and the unit before use.•

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:

This symbol points out important safety information that,

if not followed, could endanger personal safety and/or

property of others.



This symbol points out potential explosion hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical shock hazard.

GENERAL HAZARDS

Never operate in an enclosed area or indoors. •

For safety reasons, the manufacturer recommends that the •

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

Operate generator only on level surfaces and where it will not be •

exposed to excessive moisture, dirt, dust or corrosive vapors.

Keep hands, feet, clothing, etc., away from drive belts, fans, •

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

Certain parts of the generator get extremely hot during •

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

Do NOT operate generator in the rain.•

Do not alter the construction of the generator or change •

controls which might create an unsafe operating condition.

Never start or stop the unit with electrical loads connected •

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

Do not insert objects through unit’s cooling slots.•

When working on this equipment, remain alert at all times. •

Never work on the equipment when physically or mentally

fatigued.

IMPORTANT SAFETY INSTRUCTIONS

Portable Generator System

Never use the generator or any of its parts as a step. Stepping •

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

On electric start models, disconnect the POSITIVE (+) battery •

cable from the engine starter OR the NEGATIVE (-) battery

cable from the battery terminal, whichever is easier, before

transporting the generator.

NOTE:

This generator is equipped with a spark arrestor muffler. The

spark arrestor must be maintained in effective working order

by the owner/ operator. In the State of California, a spark

arrestor is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

Never operate in an enclosed area or indoors! • NEVER use in

the home, or in partly enclosed areas such as garages, even

if doors and windows are open! ONLY use outdoors and far

from open windows, doors, vents, and in an area that will not

accumulate deadly exhaust.

The engine exhaust fumes contain carbon monoxide, which •

can you cannot see or smell. This poisonous gas, if breathed

in sufficient concentrations, can cause unconsciousness or

even death.

Adequate, unobstructed flow of cooling and ventilating air •

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

This exhaust system must be properly maintained. Do nothing •

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

The manufacturer recommends installing a battery operated •

carbon monoxide alarm indoors, according to the manufacturers

instructions.

ELECTRICAL HAZARDS

The • generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

Never handle any kind of electrical cord or device while •

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

The National Electric Code (NEC) requires the frame and external •

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

Use a ground fault circuit interrupter in any damp or highly •

conductive area (such as metal decking or steel work).

Do not use worn, bare, frayed or otherwise damaged electrical •

cord sets with the generator.

Before performing any maintenance on the generator, disconnect •

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

In case of accident caused by electric shock, immediately shut •

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE• .

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

Never add fuel while unit is running or hot. Allow engine to cool •

completely before adding fuel.

Never fill fuel tank indoors. • Comply with all laws regulating

storage and handling of gasoline.

Do not overfill the fuel tank. Always allow room for fuel •

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

Wipe up any fuel or oil spills immediately. Ensure that no •

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

IMPORTANT SAFETY INSTRUCTIONS

Portable Generator System

Do not insert objects through unit’s cooling slots.•

Do not • operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

Keep a fire extinguisher near the generator at all times. •

STANDARDS INDEX

In the absence of pertinent standards, codes, regulations and laws,

the published information listed below may be used as a guideline

for operation of this equipment. Always reference the latest revision

available for the standards listed.

1. NFPA No. 70, NFPA HANDBOOK OF NATIONAL ELECTRIC

CODE.

2. Article X, NATIONAL BUILDING CODE, available from the

American Insurance Association, 85 John Street, New York,

N.Y. 10038.

3. AGRICULTURAL WIRING HANDBOOK, available from the Food

and Energy Council, 909 University Avenue, Columbia, MO

65201.

4. ASAE EP-3634, INSTALLATION AND MAINTENANCE OF

FARM STANDBY ELECTRICAL SYSTEMS, available from the

American Society of Agricultural Engineers, 2950 Niles Road,

St. Joseph, MI 49085.

MODEL NO:

SERIAL NO:

Generator Identification

Unit ID

Locations

IMPORTANT SAFETY INSTRUCTIONS

Portable Generator System

1.1 UNPACKING

Remove all packaging material.•

Remove separate accessory box.•

Remove carton off the generator.•

1.1.1 ACCESSORY BOX

Check all contents (Figure 1). If any parts are missing or damaged

locate an authorized dealer at 1-888-775-6937.

Contents include:

Wheel Axle • Oil Funnel•

2 – Washers • 2 – Wheels•

2 – Cotter Pins • Extension Cord•

Spark Plug • 12 Volt Adaptor Plug Charger•

Air Filter • Spark Plug Wrench•

Oil Filter • Shop Towel•

2 – 1 Quart SAE 30 Oil Bottles•

Figure 1 – Accessory Boxes

1.2 ASSEMBLY

Read entire Owner's Manual before attempting to assemble or

operate the generator. The generator requires some assembly

prior to using it. If problems arise when assembling the generator,

please call the Generator Helpline at 1-888-775-6937.

1.2.1 ASSEMBLING THE WHEEL KIT

The wheel kit is designed to greatly improve the portability of the

generator. A pair of pliers is needed for assembling the wheel kit.

NOTE:

The wheel kit is not intended for over-the-road use.

Refer to Figure 2 and install the wheel kit as follows:•

Generator will be resting on an accessory box after box is cut •

back.

Open end of accessory box to remove contents.•

Slide the axle through the holes on the axle brackets.•

Slide one wheel onto the axle with flat washer to the outside.•

Insert retaining pin and using pliers, bend out the ends to •

prevent the pins from falling out of the axle. Repeat for other

side.

Lift the engine side of the generator to pull out the insert.•

Figure 2 – Wheel Assembly

Axle

Wheel

Cotter Pin

Flat Washer

1.2.2 BATTERY CONNECTION

NOTE:

The battery shipped with the generator has been fully charged.

A battery may lose some of its charge when not in use for

prolonged periods of time. If the battery is unable to crank the

engine, plug in the 12V charger included in the accessory box

(see the Charging a Battery section). RUNNING THE GENERATOR

DOES NOT CHARGE THE BATTERY.

This wire was deliberately left detached for shipping. To operate

unit, attach this wire to terminal on starter motor as shown. Do not

overtighten. See Figure 3.

Figure 3 - Battery Connections

Starter Wire

(RED to Contactor)

Section 1 – General Information

Portable Generator System

2.1 KNOW THE GENERATOR

Read the entire Owner’s Manual and Safety Rules before

operating this generator.

Compare the generator to Figures 4 through 6 to become

familiarized with the locations of various controls and adjustments.

Save this manual for future reference.

1. Battery Charger Input – This receptacle allows the capability

to recharge the 12 volt DC storage battery provided with

the 12 Volt Adaptor Plug Charger which is included in the

Accessory Box. Located behind the battery charger input is

a 1.50 Amp in-line fuse which is inside the control panel to

protect the battery.

2. 120 Volt AC, 20 Amp, GFCI Duplex Receptacle – Supplies

electrical power for the operation of 120 Volt AC, 20 Amp,

single-phase, 60 Hz electrical lighting, appliance, tool and

motor loads. It also provides protection with an Integral

Ground Fault Circuit Interrupter, complete with a press to

"Test" and "Reset" button.

3. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 Volt AC,

30 Amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

4. Circuit Breakers (AC) – Each 20 Amp receptacle is provided

with a push-to-reset circuit breaker to protect the generator

against electrical overload. The 30 Amp receptacle is protected

by a 2-pole lever circuit breaker.

5. Hourmeter – Provides operating hours for Service Intervals.

6. Fuel Shut Off – Valve between fuel tank and carburetor. Turn

off and run carburetor out of fuel for extended storage.

7. Choke Knob – Used when starting a cold engine (Pull/Push).

8. Start/Run/Stop Switch – Controls the operation of the

generator.

9. Air Cleaner – Filters intake air as it is drawn into the engine.

10. Fuel Tank – Tank holds 9 U.S. gallons of fuel.

11. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

12. Muffler – Includes the spark arrestor and quiets the engine.

13. Battery – Powers the electric starter (End panel removed - 4

Torx Screws "T27").

14. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles (14A).

Figure 4 - Control Panel

2 3

4 56

7 8

15. Gas Cap – Fuel fill location.

16. Fuel Gauge – Shows fuel level in tank.

17. Oil Fill – Check oil level and add oil here.

18. Recoil Starter – Use to start engine manually.

19. Spark Plug – Ignites Air/Fuel Mixture (End & Side panel

removed - 4 Torx Screws "T27").

Figure 5 - Generator Controls

Figure 6 - Generator Controls

14A

Section 2 – Operation

Portable Generator System

Section 2 – Operation

Portable Generator System

2.2 HOURMETER

The Hourmeter tracks hours of operation for scheduled

maintenance:

There will be a one time break in "CHG OIL" message that flashes

with the elapsed time in hours and tenths after the first 30 hours

of operation.

This message will actually begin flashing at 29 hours and disable

itself at 31 hours providing a two hour window to perform the

service.

There will be a subsequent "CHG OIL" message every 100 hours.

The message will flash one hour before and one hour after each

100 hour interval, again providing a two hour window to perform

service.

Every 200 hours the "SVC" icon on the lower left hand corner of

the display will flash. The message will flash one hour before and

one hour after each 200 hour interval providing a two hour window

to perform service.

When the hour meter is in the Flash Alert mode, the maintenance

message will always alternate with elapsed time in hours and

tenths. The hours will flash four times, then alternate with the

maintenance message four times until the meter resets itself.

30 hours - CHG OIL — Break-in Interval (First 30 hrs only)•

100 hours - CHG OIL — Oil Change Interval (Every 100 hrs)•

200 hours - SVC — Air Filter Interval (Every 200 hrs)•

2.3 CORD SETS AND CONNECTION PLUGS

2.3.1 120 VAC, 20 AMP, GFCI DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 7). Use each socket to power

120 Volt AC, single phase, 60 Hz electrical loads requiring up to a

combined 2400 watts (2.4 kW) or 20 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

Keep extension cords as short as possible, preferably less than

15 feet long, to prevent voltage drop and possible overheating of

wires.

Figure 7 - 120 Volt AC, 20 Amp, GFCI Duplex Receptacle

2.3.2 120/240 VAC, 30 AMP RECEPTACLE

Use a NEMA L14-30 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 4-wire grounded cord set to the plug

and to the desired load. The cord set should be rated for 250 Volts

AC at 30 Amps (or greater) (Figure 8).

Figure 8 - 120/240 VAC, 30 Amp Receptacle

Use this receptacle to operate 120 Volt AC, 60 Hz, single phase

loads requiring up to 3600 watts (3.6 kW) of power at 30 Amps or

240 Volt AC, 60 Hz, single phase loads requiring up to 7200 watts

(7.2 kW) of power. The outlet is protected by either a 30 Amp

(8.0kW) circuit breaker.

2.4 HOW TO USE THE GENERATOR

If there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.

Never operate in an enclosed area or indoors!

NEVER use in the home, or in partly enclosed

areas such as garages, even if doors and

windows are open! ONLY use outdoors and far

from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

The engine exhaust fumes contain carbon

monoxide, which can you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or

even death.

Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions,

as this can seriously affect safe operation

of the generator. The generator MUST be

operated outdoors.

This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.

The manufacturer recommends installing

a battery operated carbon monoxide alarm

indoors, according to the manufacturers

instructions.

2.4.1 SYSTEM GROUND

The generator has a system ground that connects the generator

frame components to the ground terminals on the AC output

receptacles. The system ground is bonded to the AC neutral wire

in the generator control panel via a jumper wire.

2.4.1.1 Special Requirements 

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances that

apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

In some areas, generators are required to be registered with •

local utility companies.

If the generator is used at a construction site, there may be •

additional regulations which must be observed.

2.4.1.2 Connecting to a Building’s Electrical System 

Connections for standby power to a building’s electrical system

must be made by a qualified electrician. The connection must

isolate the generator power from utility power or other alternative

power sources and must comply with all applicable laws and

electrical codes.

2.4.2 GROUNDING THE GENERATOR

The National Electrical Code requires that the

frame and external electrically conductive parts

of this generator be properly connected to an

approved earth ground.

Local electrical codes may also require proper grounding of

the unit (Figure 6). For that purpose, connecting a No. 10 AWG

(American Wire Gauge) stranded copper wire to the grounding lug

and to an earth-driven copper or brass grounding rod (electrode)

provides adequate protection against electrical shock. However,

local codes may vary widely. Consult with a local electrician for

grounding requirements in the area.

Proper grounding of the generator will help prevent electrical

shock in the event of a ground fault condition in the generator or in

connected electrical devices. Proper grounding also helps dissipate

static electricity, which often builds up in ungrounded devices.

Figure 9 - Grounding the Generator

2.4.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles.

DO NOT connect 3 phase loads to the generator.

DO NOT connect 50 Hz loads to the generator.

Let engine stabilize and warm up for a few minutes after •

starting.

Plug in and turn on the desired 120 or 240 Volt AC, single •

phase, 60 Hz electrical loads.

Add up the rated watts (or amps) of all loads to be connected •

at one time. This total should no be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See “Don’t

Overload the Generator”.

2.5 DON’T OVERLOAD THE GENERATOR

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

Add up the total wattage of all electrical devices to be connected •

at one time. This total should NOT be greater than the

generator's wattage capacity.

The rated wattage of lights can be taken from light bulbs. The •

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

Section 2 – Operation

Portable Generator System

If the appliance, tool or motor does not give wattage, multiply •

volts times ampere rating to determine watts (volts x amps =

watts).

Some electric motors, such as induction types, require about •

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining

how many items the generator can operate at one time.

NOTE:

All figures are approximate. See data label on appliance for

wattage requirements.

2.6 WATTAGE REFERENCE GUIDE

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9"). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 to 750

Hair Dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld). . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 to 200

*Refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 to 500

Toaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

2.7 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.7.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

Above 40° F, use SAE 30•

Below 40° F and down to 10° F, use 10W-30•

Below 10° F, use synthetic 5W-30•

Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine

failure.

Place generator on a level surface.•

Clean area around oil fill and remove oil fill cap.•

10W-30

10 W -3 0

SAE 30

SA E 3 0

Synthetic 5W-30

Syn t he ti c 5W -3 0

Section 2 – Operation

Portable Generator System

Slowly fill engine with oil through the oil fill opening until it •

reaches the full mark. Stop filling occasionally to check oil

level. (Engine oil is full when level is up to the threads of the

oil fill plug.)

Install oil fill cap and finger tighten securely.•

Check engine oil level before starting each time thereafter.•

2.7.2 ADDING GASOLINE



Never fill fuel tank indoors. Never fill fuel tank

when engine is running or hot. Avoid spilling

gasoline on a hot engine. Allow engine to cool

entirely before filling fuel tank. DO NOT light a

cigarette or smoke when filling the fuel tank.



Do not overfill the fuel tank. Always leave room

for fuel expansion. If the fuel tank is overfilled,

fuel can overflow onto a hot engine and cause

FIRE or EXPLOSION. Wipe up any spilled fuel

immediately.



Do not light a cigarette ro smoke whin filling the

fuel tank. Gasoline is highly FLAMMABLE and

its vapors are EXPLOSIVE.

Use regular UNLEADED gasoline with the generator engine. Do •

not use premium gasoline. Do not mix oil with gasoline.

Do not use gasoline with more than 10% alcohol such as E85 •

or Methanol.

Clean area around fuel fill cap, remove cap.•

Slowly add unleaded regular gasoline to fuel tank. Fill to bottom •

of screen filter. Be careful not to overfill (Figure 10).

Install fuel cap and wipe up any spilled gasoline. •

Figure 10 - Fuel Tank

DO NOT Fill Above Lip

Fuel

Fuel Tank

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may

occur.

2.8 TO START THE ENGINE



Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

Unplug all electrical loads from the unit's receptacles before •

starting the engine.

Make sure the unit is in a level position.•

Open the fuel shut-off valve (Figure 11).•

Figure 11 - Fuel Shut-off Valve

Pull engine CHOKE knob outward to • “Full Choke” position

(Figure 12).

Figure 12 - Choke Position

Choke

To start engine, press and hold the Start/Run/Stop switch in •

the “Start” position. The engine will crank and attempt to start.

When the engine starts, release the switch to the run position.

When the engine starts, push choke knob to “1/2 Choke” •

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, pull choke knob back out to

“1/2 Choke” position until the engine runs smoothly and then

to “Run” position.

This generator is also equipped with a manual recoil starter •

which may be used if the battery is discharged.

NOTE:

The switch must be in the RUN position.

Section 2 – Operation

Portable Generator System

To start manually, firmly grasp the recoil handle and pull slowly •

until increased resistance is felt. Pull rapidly up and away to

start engine. Then follow the same choke sequence listed

above.

NOTE:

If engine fires, but does not continue to run, pull choke knob to

“Full Choke” and repeat starting instructions.

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset-type circuit breakers. If amperage

rating of any circuit breaker is exceeded, that breaker opens and

electrical output to that receptacle is lost. Read “Don’t Overload the

Generator” carefully.

2.9 STOPPING THE ENGINE

Shut off all loads, then unplug the electrical loads from generator •

panel receptacles. Never start or stop the engine with electrical

devices plugged in and turned on.

Let engine run at no-load for several minutes to stabilize the •

internal temperatures of engine and generator.

Move Start/Run/Stop switch to “Off” position.•

Close fuel valve.•

2.10 LOW OIL PRESSURE SHUTDOWN SYSTEM

The engine is equipped with a low oil pressure sensor that shuts

down the engine automatically when the oil pressure drops below

5 psi. If the engine shuts down by itself and the fuel tank has

enough gasoline, check engine oil level.

2.10.1 INITIAL START-UP

A delay built into the low oil shutdown system allows oil pressure

to build during starting. The delay allows the engine to run for

about 10 seconds before sensing oil pressure.

2.10.2 SENSING LOW OIL PRESSURE

If the system senses low oil pressure during operation, the engine

shuts down.

2.10.3 RESTARTING

If trying to restart the engine within 10 seconds after it shuts down,

the engine may NOT start. The system needs 5 to 10 seconds to

reset.

If the engine is restarted after such a shutdown and the low oil

pressure has not been corrected, the engine will run for about 10

seconds as described above and then stop.

2.11 CHARGING A BATTERY



Storage batteries give off explosive hydrogen

gas while recharging. An explosive mixture will

remain around the battery for a long time after

it has been charged. The slightest spark can

ignite the hydrogen and cause an explosion.

Such an explosion can shatter the battery and

cause blindness or other serious injury.

Do not permit smoking, open flame, sparks or

any other source of heat around a battery. Wear

protective goggles, rubber apron and rubber

gloves when working around a battery. Battery

electrolyte fluid is an extremely corrosive

sulfuric acid solution that can cause severe

burns. If spill occurs flush area with clear water

immediately.

Use battery charger plug to keep the battery charged and ready for

use. Battery charging should be done in a dry location.

1. Plug charger into “Battery Charger Input” jack, located on the

control panel. Plug wall receptacle end of the battery charger

into a 120 Volt AC wall outlet (Figure 13).

Figure 13 - Battery Charger Jack

2. Unplug battery charger from wall outlet and control panel jack

when generator is going to be in use.

NOTE:

Do not use the battery charger for more than 48 hours at one

charge.

Section 2 – Operation

Portable Generator System

3.1 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil and Oil Filter‡ *Every Season

Clean Spark Arrestor Screen Every Season

Check Valve Clearance ***Every Season

Service Air Cleaner **Every Season

Replace Spark Plug Every Season

‡ Change oil after first 30 hours of operation then every season.

* Change oil and oil filter every month when operating under heavy load or in high

temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air cleaner

parts if very dirty.

*** Check valve clearance and adjust if necessary after first 50 hours of

operation and every 100 hours thereafter.

3.2 PRODUCT SPECIFICATIONS

3.2.1 GENERATOR SPECIFICATIONS

Model # .................................................................................005708-1

Rated Max. Power ...................................................................8.0 kW**

Surge Power ................................................................................12 kW

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V .............................................................33.3 Amps**

Current @ 120V .............................................................66.7 Amps**

Rated Frequency .................................................... 60 Hz @ 3600 RPM

Phase ................................................................................Single Phase

Rated DC Voltage ...................................................................... 12 Volts

** Maximum wattage and current are subject to, and limited by, such factors

as fuel Btu content, ambient temperature, altitude, engine condition, etc..

Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16° C (60° F)

ambient temperature.

3.2.2 ENGINE SPECIFICATIONS

Rated Horsepower @ 3600 RPM ....................................................14.5

Displacement ...............................................................................410cc

Spark Plug Type ...................................Champion RC14YC or Equivalent

Spark Plug Gap ............................................... 0.030 inch or (0.76 mm)

Gasoline Capacity ............................................................ 9 U.S. gallons

Oil Type....................................See Chart in "Adding Engine Oil" Section

Oil Capacity ................................................ w/ Filter Change = 1.5 Qts.

w/o Filter Change = 1.2 Qts.

Run Time/Fuel Consumption-1/2 Load .. 12 Hours / .73 gallons per hour

Class II Emission Certified

3.3 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTE:

Once a year replace the spark plug and replace the air filter.

A new spark plug and clean air filter assure proper fuel-air

mixture and help the engine run better and last longer.

3.3.1 GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.

Never insert any object or tool through the air

cooling slots, even if the engine is not running.

NOTE:

DO NOT use a garden hose to clean generator. Water can enter

the engine fuel system and cause problems. In addition, if water

enters the generator through cooling air slots, some water will

be retained in voids and crevices of the rotor and stator winding

insulation. Water and dirt buildup on the generator internal

windings will eventually decrease the insulation resistance of

these windings.

3.3.2 TO CLEAN THE GENERATOR

Use a damp cloth to wipe exterior surfaces clean.•

A soft, bristle brush may be used to loosen caked on dirt, oil, •

etc.

A vacuum cleaner may be used to pick up loose dirt and •

debris.

Low pressure air (not to exceed 25 psi) may be used to •

blow away dirt. Inspect cooling air slots and openings

on the generator. These openings must be kept clean and

unobstructed.

Section 3 — Maintenance

Portable Generator System

3.3.3 ENGINE MAINTENANCE



When working on the generator, always

disconnect negative cable from battery. Also

disconnect spark plug wires from spark plug

and keep wire away from spark plug.

3.3.4 CHECKING OIL LEVEL

See the “BEFORE STARTING THE GENERATOR” section for

information on checking the oil level. The oil level should be

checked before each use, or at least every eight hours of operation.

Keep the oil level maintained.

3.3.5 CHANGING THE OIL AND OIL FILTER

Change the oil and filter after the first 30 hours of operation. Change

the oil every 100 hours or every season thereafter. If running this

unit under dirty or dusty conditions, or in extremely hot weather,

change the oil more often.

Hot oil may cause burns. Allow engine to

cool before draining oil. Avoid prolonged

or repeated skin exposure with used oil.

Thoroughly wash exposed areas with soap.

NOTE:

Whenever possible, run engine for approximately five (5)

minutes to get the engine oil hot. This will aid in draining the

oil.

Use the following instructions to change the oil while the engine

is still warm:

Clean area around oil drain plug.•

Remove oil drain plug from engine and oil fill plug to drain oil •

completely into a suitable container.

When oil has completely drained, install oil drain plug and •

tighten securely.

Place a suitable container beneath the oil filter and turn •

filter counterclockwise to remove. Discard according to local

regulations.

Coat gasket of new filter with clean engine oil. Turn filter •

clockwise until gasket contacts lightly with filter adapter. Then

tighten an additional 3/4 turn.

Fill oil sump with recommended oil. (See “Before Starting the •

Generator” for oil recommendations).

Wipe up any spilled oil.•

Dispose of used oil at a proper collection center.•

3.3.6 REPLACING THE SPARK PLUG

Use Champion RC14YC spark plug or equivalent. Replace the

plug once each year. This will help the engine start easier and

run better.

1. Stop the engine and pull the spark plug wire off of the spark

plug.

2. To gain access, remove the four (4) Torx screws "T27" and

take off side panel.

3. Clean the area around the spark plug and remove it from the

cylinder head.

4. Set the spark plug's gap to .76 mm (0.030 in.). Install the

correctly gapped spark plug into the cylinder head (Figure

14).

5. Push the boot firmly on the spark plug and install side panel.

Figure 14 - Spark Plug Gap

3.4 SERVICE AIR CLEANER

The engine will not run properly and may be damaged if using a

dirty air cleaner. Clean or replace the air cleaner paper filter once

a year (Figure 15). Clean or replace more often if operating under

dusty conditions.

To clean or replace paper air filter:

Remove air cleaner cover; then remove foam pre-filter (service •

if necessary) and remove paper filter.

Clean paper filter by tapping it gently on a solid surface. If the •

filter is too dirty, replace it with a new one. Dispose of the old

filter properly.

Clean air cleaner cover then slip pre-cleaner over filter. Next •

insert new paper filter into the base of the air cleaner. Re-install

air cleaner cover.

NOTE:

To order a new air filter, please contact the nearest authorized

service center at 1-888-775-6937.

Section 3 — Maintenance

Portable Generator System

Section 3 — Maintenance

Portable Generator System

Figure 15 - Air Cleaner

BASE

FILTER

COVER

3.5 CLEAN SPARK ARRESTOR SCREEN

The engine exhaust muffler has a spark arrestor screen. Inspect

and clean the screen at least once each year (Figure 16). If unit is

used regularly, inspect and clean more often.

NOTE:

If using the generator on any forest-covered, brush-covered

or grass-covered unimproved land, it must equipped with a

spark arrestor. The spark arrestor must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrestor when the engine is at

ambient temperature as follows:

Remove muffler heat shield from muffler by removing the four •

screws.

Remove spark arrestor from muffler by removing the four •

screws.

Inspect screen and replace if torn, perforated or otherwise •

damaged. DO NOT USE a defective screen. If screen is not

damaged, clean it with commercial solvent.

Replace the spark arrestor and muffler heat shield.•

Figure 16 - Spark Arrestor

Heat Shield

Spark Arrestor

3.6 ADJUSTING VALVE CLEARANCE

After the first 50 hours of operation, check the valve clearance

in the engine and adjust if necessary.

Important: If feeling uncomfortable about doing this procedure or

the proper tools are not available, please take the generator to the

nearest service center to have the valve clearance adjusted. This is

a very important step to insure longest life for the engine.

To check valve clearance:

Make sure the engine is at ambient temperature (60° - 80° F).•

Make sure that the spark plug wire is removed from the spark •

plug and out of the way. Remove spark plug.

Remove the four screws attaching the valve cover.•

Make sure the piston is at Top Dead Center (TDC) of its •

compression stroke (both valves closed). To get the piston

at TDC, remove the intake screen at the front of the engine to

gain access to the flywheel nut. Use a large socket and socket

wrench to rotate the nut and hence the engine in a clockwise

direction while watching the piston through the spark plug hole.

The piston should move up and down. The piston is at TDC

when it is up as high as it can go.

Insert a 0.002 - 0.004 inch (0.05 - 0.1mm) feeler gauge •

between the rocker arm and valve stem. Correct clearance is

when a slight drag is felt when sliding the gauge back and forth.

If the clearance is either excessively loose or tight the rocker

arms will need adjusting.

To adjust valve clearance:

Loosen the rocker jam nut (Figure 17). Use an 10mm allen •

wrench to turn the pivot ball stud while checking clearance

between the rocker arm and the valve stem with a feeler gauge.

Correct clearance is 0.002-0.004 inch (0.05-0.1 mm).

NOTE:

The rocker arm jam nut must be held in place as the pivot ball

stud is turned.

Figure 17 - Valve Clearance Adjustment

When valve clearance is correct, hold the pivot ball stud in place

with the allen wrench and tighten the rocker arm jam nut. Tighten

the jam nut to 174 in/lbs. torque. After tightening the jam nut,

recheck valve clearance to make sure it did not change.

Install new valve cover gasket.•

Re-attach the valve cover.•

NOTE:

Start all four screws before tightening or it will not be possible

to get all the screws in place. Make sure the valve cover gasket

is in place. Replace spark plug.

Re-attach the spark plug wire to the spark plug.•

3.7 GENERAL

The generator should be started at least once every seven days

and be allowed to run at least 30 minutes. If this cannot be done

and the unit must be stored for more than 30 days, use the

following information as a guide to prepare it for storage.



NEVER store engine with fuel in tank indoors

or in enclosed, poorly ventilated areas where

fumes may reach an open flame, spark or pilot

light as on a furnace, water heater, clothes

dryer or other gas appliance.

Allow unit to cool entirely before storage.

It is important to prevent gum deposits from forming in

essential fuel system parts such as the carburetor, fuel hose

or tank during storage. Also, experience indicates that alcohol-

blended fuels (called gasohol, ethanol or methanol) can attract

moisture, which leads to separation and formation of acids during

storage. Acidic gas can damage the fuel system of an engine while

in storage.

To avoid engine problems, the fuel system should be emptied

before storage of 30 days or longer, as follows:

Remove all gasoline from the fuel tank.•





Drain fuel into approved container outdoors,

away from open flame. Be sure engine is cool.

Do not smoke in the vicinity or light a cigarette.

Start and run engine until engine stops from lack of fuel.•

While engine is still warm, drain oil from crankcase. Refill with •

recommended grade.

Remove spark plugs and pour about 1/2 ounce (15 ml) of •

engine oil into the cylinders. Cover spark plug hole with rag.

Pull the recoil starter a couple times to lubricate the piston rings

and cylinder bore.

Avoid spray from spark plug holes when

cranking engine.

Install and tighten spark plugs. Do not connect spark plug •

wires.

Clean the generator outer surfaces. Check that cooling air slots •

and openings on generator are open and unobstructed.

Store the unit in a clean, dry place.•

3.8 LONG TERM STORAGE

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

storage. Also, experience indicates that alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract moisture, which

leads to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied

before storage of 30 days or longer, as follows:

Remove all gasoline from the fuel tank.•



Drain fuel into approved container outdoors,

away from open flame. Be sure engine is cool.

Do not smoke in the vicinity or light a cigarette.

Start and run engine until engine stops from lack of fuel.•

While engine is still warm, drain oil from crankcase. Refill with •

recommended grade.

Remove spark plugs and pour about 1/2 ounce (15 ml) of •

engine oil into the cylinders. Cover spark plug hole with rag.

Pull the recoil starter a couple times to lubricate the piston rings

and cylinder bore.

Avoid spray from spark plug holes when

cranking engine.

Install and tighten spark plugs. Do not connect spark plug •

wires.

Clean the generator outer surfaces. Check that cooling air slots •

and openings on generator are open and unobstructed.

Store the unit in a clean, dry place.•

Section 3 — Maintenance

Portable Generator System

3.9 OTHER STORAGE TIPS

Do not store gasoline from one season to another.•

Replace the gasoline can if it starts to rust. Rust and/or dirt in •

the gasoline will cause problems with the carburetor and fuel

system.

If possible, store the unit indoors and cover it to give protection •

from dust and dirt. BE SURE TO EMPTY THE FUEL TANK.

If it is not practical to empty the fuel tank and the unit is to be •

stored for some time, use a commercially available fuel stabilizer

added to the gasoline to increase the life of the gasoline.

Cover the unit with a suitable protective cover that does not •

retain moisture.

NEVER cover the generator while engine and

exhaust area are warm. Allow unit to cool

entirely.

4.1 BATTERY SERVICE (REPLACEMENT)

The battery shipped with the generator has been provided fully

charged. Caution must be taken when connecting the battery.

NOTE:

A battery may lose some of it’s charge when not in use for

prolonged periods of time. The battery may have to be recharged

before the first use. (See the "Know the Generator" section.)

To replace the battery:

Remove end panel as shown in Figure 5 in the "Know the •

Generator" section.

Remove hold-down bracket.•

Disconnect the BLACK battery cable to the battery Negative •

terminal (–).

Disconnect the RED battery cable to the battery Positive •

terminal (+).

To install a new battery:

Reverse the steps above and follow Figure 18.•

Double check all connections to ensure they are in the correct •

location and secure. See Figure 18.

Figure 18 - Battery Connections

NEGATIVE BATTERY

CABLE (BLACK)

NUT

LOCK WASHER

CABLE BOOT

FLAT WASHER

POSITIVE BATTERY

CABLE (RED)

SCREW

GROUND

(GREEN)

BATTERY CHARGER

(RED)

BATTERY CHARGER

(BLACK)

Battery Type: 12V, 10AH

Section 4 — Battery Service

Portable Generator System

5.1 TROUBLESHOOTING GUIDE

PROBLEM CAUSE CORRECTION

Engine is running, but no AC output

is available.

1. Circuit breaker is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Fault in generator.

5. GFCI trips the 20 Amp outlet.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good condition.

4. Contact Authorized Service Facility.

5. Repair the "short" and reset the GFCI.

Engine runs good but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See “Don’t Overload the Generator” .

3. Contact Authorized Service Facility.

4. Contact Authorized Service Facility.

Engine will not crank. 1. Battery weak or dead. 1. Recharge or replace battery (see "No Battery

Charger DC output" at bottom of guide).

2. Start engine manually using recoil starter.

Engine will not start; or starts and

runs rough.

1. Fuel shut-off is OFF.

2. Dirty air cleaner.

3. Out of gasoline.

4. Stale gasoline.

5. Spark plug wire not connected to spark plug.

6. Bad spark plug.

7. Water in gasoline.

8. Over-choking.

9. Low oil level.

10. Excessive rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Turn Fuel shut-off ON.

2. Clean or replace air cleaner.

3. Fill fuel tank.

4. Drain fuel tank and fill with fresh fuel.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Drain fuel tank; fill with fresh fuel.

8. Put choke knob to No Choke position.

9. Fill crankcase to proper level.

10. Contact Authorized Service Facility.

11. Contact Authorized Service Facility.

12. Contact Authorized Service Facility.

Engine shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to proper level.

3. Contact Authorized Service Facility.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

1. See “Don’t Overload the Generator”.

2. Replace air filter.

3. Contact Authorized Service Facility.

Engine “hunts” or falters. 1. Choke is opened too soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until engine runs

smoothly.

2. Contact Authorized Service Facility.

No Battery Charger DC output. 1. Battery posts are corroded.

2. Battery cable is bad.

3. Battery is defective.

4. Receptacle is bad.

5. Battery Charger in-line fuse (1.5A) melted open.

1. Clean battery posts.

2. Replace cable.

3. Check battery condition; replace if defective.

4. Contact Authorized Service Facility.

5. Replace fuse with identical 1.5A replacement fuse

only (located inside control panel).

Section 5 — Troubleshooting

Portable Generator System

Section 6 — Notes

Section 7 – Warranty

Portable Generator System

FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain the

Emission Control System warranty on your new 2008 and later equipment. New equipment that use small spark-ignited engines

must be designed, built, and equipped to meet stringent anti-smog standards for the federal government. Generac will warrant

the emission control system on your generator for the period of time listed below provided there has been no abuse, neglect,

unapproved modification or improper maintenance of your equipment.

Your emission control system may include parts such as the: carburetor, ignition system, fuel system, catalytic converter, and other

associated emission-related components (if equipped).

MANUFACTURER’S WARRANTY COVERAGE:

This emission control system is warranted for two years. If, during such warranty period, any emission-related part on your

equipment is found to be defective in materials or workmanship, repairs or replacement will be performed by a Generac

Authorized Warranty Service Dealer.

OWNER'S WARRANTY RESPONSIBILITIES:

As the generator owner, you are responsible for the completion of all required maintenance as listed in your factory supplied

Owner's Manual. For warranty purposes, Generac recommends that you retain all receipts covering maintenance on your

generator, but Generac cannot deny warranty solely due to the lack of receipts.

As the generator owner, you should be aware that Generac may deny any and/or all warranty coverage or responsibility if your

generator, or a part/component thereof, has failed due to abuse, neglect, improper maintenance or unapproved modifications, or

the use of counterfeit and/or "grey market" parts not made, supplied or approved by Generac.

You are responsible for contacting a Generac Authorized Warranty Dealer as soon as a problem occurs. The warranty

repairs should be completed in a reasonable amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either your selling dealer or a Generac Authorized Warranty Service Dealer. To

locate the Generac Authorized Warranty Service Dealer nearest you, call our toll free number:

1-800-333-1322

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Control System Warranty

(ECS Warranty), which is provided to you by Generac pursuant to federal law. See also the "Generac Limited Warranties for

Generac Power Systems, Inc.," which is enclosed herewith on a separate sheet, also provided to you by Generac. Note that this

warranty shall not apply to any incidental, consequential or indirect damages caused by defects in materials or workmanship or

any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties, expressed or implied.

Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Some states do not

allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

The ECS Warranty applies only to the emission control system of your new equipment. If there is any conflict in terms between the

ECS Warranty and the Generac Warranty, the Generac Warranty shall apply. Both the ECS Warranty and the Generac Warranty

describe important rights and obligations with respect to your new engine.

Warranty service can be performed only by a Generac Authorized Warranty Service Facility. When requesting warranty service,

evidence must be presented showing the date of the sale to the original purchaser/owner.

If you have any questions regarding your warranty rights and responsibilities, you should contact Generac at the following

address:

ATTENTION WARRANTY DEPARTMENT

GENERAC POWER SYSTEMS, INC.

P.O. BOX 297 • WHITEWATER, WI 53190

Part 1

Part No. 0H1911 Rev. A 01/09

La page charge ...

Generac XP8000E 0057081 Manuel utilisateur

Marque: Generac

Modèle: XP8000E 0057081

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac XP8000E 0057081 User manual
español: Generac XP8000E 0057081 Manual de usuario