Dometic PerfectView VT50WiFi Mode d'emploi

VT50WiFi

WiFi rear view system with

smartphone app

Installation and Operating Manual . . . . . . 8

WiFi-Rückfahrvideosystem mit

Smartphone-App

Montage- und Bedienungsanleitung . . . 18

Système vidéo de recul WiFi avec

application smartphone

Instructions de montage

et de service . . . . . . . . . . . . . . . . . . . . . . . 28

Sistema de vídeo para marcha

atrás con app para smartphone

Instrucciones de montaje y de uso . . . . .39

Sistema de vídeo de marcha-atrás

WiFi com aplicação para

smartphone

Instruções de montagem e manual de

instruções . . . . . . . . . . . . . . . . . . . . . . . . . 49

Sistema video per retromarcia

WiFi con app per smartphone

Istruzioni di montaggio e d’uso . . . . . . . . 59

WiFi-achteruitrijvideosysteem met

smartphone-app

Montagehandleiding en

gebruiksaanwijzing . . . . . . . . . . . . . . . . . 70

WiFi-bakkamerasystem med

smartphone-app

Monterings- og betjeningsvejledning . . 80

WiFi-backvideosystem med

mobiltelefon-app

Monterings- och bruksanvisning. . . . . . . 90

WiFi-ryggevideosystem med

smarttelefon-app

Monterings- og bruksanvisning . . . . . . 100

WiFi-peruutusvideojärjestelmä

älypuhelinsovelluksella

Asennus- ja käyttöohje. . . . . . . . . . . . . . .110

Видеосистема заднего обзора с

поддержкой WiFi и мобильным

приложением

Инструкция по монтажу

и эксплуатации. . . . . . . . . . . . . . . . . . . . 120

System wideo cofania WiFi

z aplikacją na smartfona

Instrukcja montażu i obsługi . . . . . . . . . .131

WiFi cúvací videosystém

s aplikáciou pre smartfóny

Návod na montáž a uvedenie

do prevádzky . . . . . . . . . . . . . . . . . . . . . .141

WiFi kamerový systém pro couvání

s aplikací pro smartphony

Návod k montáži a obsluze . . . . . . . . . . .151

WiFi tolató-videorendszer

okostelefon applikációval

Szerelési és használati útmutató . . . . . . .161

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

DRIVING SUPPORT

PERFECTVIEW

VT50WiFi-IO-16s.book Seite 1 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi-IO-16s.book Seite 2 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi

3

1

2

5

4

3

2

VT50WiFi-IO-16s.book Seite 3 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi

4

1

2

3

4

9

6 8

5

7

10

11

3

VT50WiFi-IO-16s.book Seite 4 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi

5

180°

1

2

4

180°

1

2

5

VT50WiFi-IO-16s.book Seite 5 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi

6

1.

2.

7

8

VT50WiFi-IO-16s.book Seite 6 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi

7

2.

1.

1

3

2

9

VT50WiFi-IO-16s.book Seite 7 Mittwoch, 12. Dezember 2018 7:08 19

Explanation of symbols VT50WiFi

EN

8

Please read this instruction manual carefully before installation and first use, and store

it in a safe place. If you pass on the product to another person, hand over this instruc-

tion manual along with it.

Table of contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2 Safety and installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

5 Technical description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6 Mounting the camera and transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

7 Connecting the transmitter electrically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

8 Using VT50WiFi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

10 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

12 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1 Explanation of symbols

!

A

I

WARNING!

Safety instruction: Failure to observe this instruction can cause death or serious

injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair the function

of the product.

NOTE

Supplementary information for operating the product.

VT50WiFi-IO-16s.book Seite 8 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Safety and installation instructions

EN

9

2 Safety and installation instructions

The manufacturer accepts no liability for damage in the following cases:

•

Damage to the product resulting from mechanical influences and incorrect connection voltage

•

Alterations to the product without express permission from the manufacturer

•

Use for purposes other than those described in the operating manual

Please observe the prescribed safety instructions and stipulations from the vehicle

manufacturer and service workshops.

!

WARNING!

Inadequate supply cable connections could result in short circuits, which could have as

a consequence that:

•

Cable fires occur

•

The airbag is triggered

•

Electronic control devices are damaged

•

Electric functions fail (indicators, brake light, horn, ignition, lights)

A

NOTICE!

To prevent the risk of short circuits, always disconnect the negative terminal of the

vehicle's electrical system before working on it.

If the vehicle has an additional battery, its negative terminal should also be discon-

nected.

Please observe the following instructions:

•

When working on the following cables, only use insulated cable lugs, plugs and flat push-on

receptacles:

– 30 (direct supply from positive battery terminal)

–15 (connected positive terminal, behind the battery)

– 31 (return line from the battery, earth)

– L (indicator lights left)

– R (indicator lights right)

Do not use terminal strips.

•

Use a crimping tool to connect the cables.

•

When connecting to cable 31 (earth), screw the cable

– to the vehicle's earth bolt with a cable lug and a gear disc or

– to the sheet-metal bodywork with a cable lug and a self-tapping screw.

Ensure that there is a good earth connection.

VT50WiFi-IO-16s.book Seite 9 Mittwoch, 12. Dezember 2018 7:08 19

Safety and installation instructions VT50WiFi

EN

10

If you disconnect the negative terminal of the battery, all data stored in the volatile memories will

be lost.

•

The following data must be set again, depending on the vehicle equipment options:

–Radio code

– Vehicle clock

–Timer

– On-board computer

– Seat position

You can find instructions for making these settings in the appropriate operating instructions.

Observe the following installation instructions:

!

CAUTION!

•

Secure the parts installed in the vehicle in such a way that they cannot become loose

under any circumstances (sudden braking, accidents) and cause injuries to the

occupants of the vehicle.

•

Secure any parts of the system covered by the bodywork in such a manner that they

cannot be come loose or damage other parts and cables or impair vehicle functions

(steering, pedals, etc).

•

Always follow the safety instructions of the vehicle manufacturer.

Some work (e.g. on retention systems such as the AIRBAG etc.) may only be

performed by qualified specialists.

A

NOTICE!

•

To prevent damage when drilling, make sure there is sufficient space on the other

side for the drill head to come out.

•

Deburr all drill holes and treat them with a rust-protection agent.

Observe the following instructions when working with electrical parts:

A

NOTICE!

•

When testing the voltage in electrical cables, only use a diode test lamp or a

voltmeter.

Test lamps with an illuminant take up voltages which are too high and which can

damage the vehicle's electronic system.

•

When making electrical connections, ensure that:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp edged ducts without protection.

•

Insulate all connections.

•

Secure the cables against mechanical wear with cable binders or insulating tape,

for example to existing cables.

VT50WiFi-IO-16s.book Seite 10 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Scope of delivery

EN

11

3Scope of delivery

4Intended use

PerfectView VT50WiFi (ref. no. 9600003262) is a rear view video camera with a WiFi transmitter.

The transmitter wirelessly transmits the signals between the rear view video camera and a smart-

phone or tablet with an iOS™ or Android™ operating system. PerfectView VT50Wi-Fi is suitable

for use in cars, caravan trailers and mobile homes (fig. 1, page 3).

5 Technical description

5.1 Function description

PerfectView VT50WiFi comprises a rear view video camera with a number plate fastening, a WiFi

transmitter and an app for mobile end devices such as smartphones or tablets.

The transmitter is mounted in the vehicle. It establishes a wireless radio network and transmits the

image over it to a smartphone or tablet.

The transmitter is connected to the reversing light and is also used to supply the camera with

power. The transmitter must re-establish the wireless connection every time the car is shifted into

reverse gear. This requires about six seconds.

The wireless signals are transmitted in the 2.4 GHz range.

As the system is only designed as an additional aid for reversing, it does not relieve you of the duty

to exercise due care especially when driving with a trailer.

A

5.2 Control elements

Quantity Label

1 Camera with number plate fastening

1Transmitter

–Fastening material

1Instruction

NOTICE!

The transmitter sends digital data. The camera image is displayed on the monitor with

a delay of 0.2 seconds. It is therefore essential that you drive slowly.

No. in

fig. 2, page 3

Meaning

1 Antenna connection

2 Camera connection

VT50WiFi-IO-16s.book Seite 11 Mittwoch, 12. Dezember 2018 7:08 19

Mounting the camera and transmitter VT50WiFi

EN

12

6 Mounting the camera and transmitter

6.1 Tools required (fig. 3, page 4)

For installation and assembly you will need the following tools:

•

Drill head set (1)

•

Drill (2)

•

Screwdriver (3)

•

Set of ring or open-ended spanners (4)

•

Tape measure (5)

•

Hammer (6)

•

Centre punch (7)

To establish and test the electrical connection, the following tools are required:

•

Diode test lamp (8) or voltmeter (9)

•

Crimping tool (10)

•

Insulating tape (11)

•

Cable bushing sleeves (optional)

To secure the camera, transmitter and the cable, you may require additional screws, cable

binders and double-sided tape.

6.2 Preparing the camera for installation

Observe the following mounting instructions:

•

Place the camera in the centre over or under the number plate. The camera requires a free space

of 30 mm above or below the number plate.

•

Fasten the camera in a way that does not cover the number plate.

3 Red cable (DC INPUT): Connection to the positive terminal (+) of the

power supply

4 Black cable (GND): Connection to the negative terminal (–) of the

power supply or earth terminal

5 Operating display; lights up as soon as voltage is applied

No. in

fig. 2, page 3

Meaning

VT50WiFi-IO-16s.book Seite 12 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Mounting the camera and transmitter

EN

13

Mounting the camera under the number plate (fig. 4, page 5)

➤ Unscrew the camera (1) from the assembly plate (2).

➤ Turn the camera by 180°.

➤ Reattach the camera to the assembly plate.

Adjusting the installation position on the rear of the vehicle (fig. 5, page 5)

The camera is attached to the upper part of the assembly plate. The upper part of the assembly

plate is bent at an angle of approximately 5°. You can fit the camera to the rear of the assembly

plate to adjust the assembly position to the shape of the vehicle rear.

➤ Unscrew the camera (1) from the assembly plate (2).

➤ Turn the assembly plate by 180°.

➤ Reattach the camera to the assembly plate.

6.3 Fastening the camera

➤ Remove the rear number plate holder from the vehicle.

➤ Attach the camera assembly plate to the rear of the number plate holder with double-sided

tape.

➤ Reattach the number plate holder to the vehicle. In doing so, press the double-sided tape onto

the bodywork.

✓ The camera is now attached to the vehicle.

6.4 Preparing the transmitter for installation

!

Observe the following mounting instructions:

•

Install the transmitter so that as few objects as possible are situated between the transmitter and

receiving device. Moving the transmitter can help if there is a poor connection.

•

The installation location should be flat.

•

Before drilling each hole, ensure there is sufficient space on the other side for the drill head to

emerge (fig. 6, page 6).

•

Make sure you can lay the connection cable from the transmitter to the camera.

I

CAUTION!

Select the location of the transmitter so that it cannot injure the passengers in the

vehicle under any circumstances (e.g. sudden braking, road traffic accidents).

NOTE

The image is sent from the transmitter to the receiving device. To ensure flawless

functioning, you need to check whether the wireless transmission is stable before final

installation.

VT50WiFi-IO-16s.book Seite 13 Mittwoch, 12. Dezember 2018 7:08 19

Connecting the transmitter electrically VT50WiFi

EN

14

6.5 Attaching the transmitter

➤ Attach the transmitter temporarily to the planned installation location.

➤ Put the transmitter into operation.

➤ Activate the app on your receiving device (see chapter “Using VT50WiFi” on page 15).

If a fault occurs, e.g. there are flickering images:

➤ Adjust the location of the transmitter slightly.

➤ Retest the transmission.

If the camera image transmission is stable (no flickering images):

➤ Secure the transmitter with double-sided tape.

7 Connecting the transmitter electrically

7.1 General notes on laying cables

I

Therefore, please observe the following instructions:

•

Wherever possible, lay cables inside the vehicle, as they are better protected there than

outside.

If you do need to lay a cable outside the vehicle, ensure that it is well fastened (use additional

cable ties, insulating tape etc.).

•

To prevent damage to the cables when laying them, ensure that they are far enough away from

hot or moving vehicle components (exhaust pipes, drive shafts, light systems, fans, heaters,

etc.).

•

Use adhesive insulating tape to prevent water from penetrating the plug connection (fig. 7,

page 6).

•

When laying the cables (fig. 8, page 6), make sure:

– they are not kinked or twisted

– they do not rub on edges

– they are not laid in sharp-edged ducts without protection.

•

Protect every through-hole made in the bodywork against water penetration, e.g. by using a

cable with a sealant and by spraying the cable and the cable sleeve with sealant.

NOTE

•

As far as possible, use original ducts for laying the cables, or other suitable options

such as panelling edges, ventilation grilles or dummy plugs.

If no openings are available, you must drill holes for the cables. Check beforehand

that there is sufficient space on the other side for the drill head to emerge.

•

Cables and connections that are not properly installed will cause malfunctions or

damage to components. Correct installation of cables and connections ensures

lasting and trouble-free operation of the retrofitted components.

VT50WiFi-IO-16s.book Seite 14 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Using VT50WiFi

EN

15

I

7.2 Connecting the transmitter electrically

A

I

Connecting the transmitter to the reversing light

I

Proceed as follows (fig. 2, page 3):

➤ Connect the red cable of the transmitter (3) to the positive cable of the reversing light.

➤ Connect the black cable of the transmitter (4) to the earth wire (–) on the reversing light or to

the earth terminal on the bodywork.

➤ Connect the transmitter to the camera (fig. 9, page 7):

– Plug the connection cable (1) together.

– Insert the plug (2) into the transmitter’s camera connection (3).

✓ After a few seconds, the VT50WiFi establishes the digital wireless connection.

8Using VT50WiFi

8.1 Installing the VT50 RearCam app

To be able to use the system, you need to install the manufacturer’s free app on your receiving

device before initial use.

You can find the app in Google Play Store™ (Android™) and in the App Store™ (iOS™) under the

name VT50 RearCam.

NOTE

Only start sealing through-holes when you have completed all installation work on the

camera and have laid the required cable lengths.

NOTICE!

Make sure the polarity is correct.

NOTE

The transmitter creates a wireless network that does not permit access to the Internet.

Therefore internet services cannot be used once the transmitter is being supplied with

power.

The use of telephony and text messages is also restricted.

NOTE

On some vehicles, the reversing light only works when the ignition is switched on. In

this case, you must switch on the ignition to identify the positive and earth cables.

VT50WiFi-IO-16s.book Seite 15 Mittwoch, 12. Dezember 2018 7:08 19

Troubleshooting VT50WiFi

EN

16

8.2 Putting VT50WiFi into operation

➤ Activate the wireless reception of your receiving device.

➤ Switch the vehicle ignition on.

➤ Engage the reverse gear of the vehicle.

✓ The transmitter is operational about six seconds after putting the vehicle into reverse gear. The

operating display (fig. 2 5page 3) lights up permanently in red on the transmitter.

➤ Connect your receiving device to the wireless network of the transmitter.

I

➤ Start the app on your receiving device.

✓ The receiving device displays the camera image.

9 Troubleshooting

10 Warranty

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the addresses) or

your retailer.

For repair and warranty processing, please include the following documents when you send in the

device:

•

A copy of the receipt with purchasing date

•

A reason for the claim or description of the fault

NOTE

The name and the password of the wireless network can be found on the transmitter.

Fault Cause Suggested remedy

The receiving device can-

not find the transmitter’s

wireless network.

The transmitter does not

work.

Check the power supply.

The transmitter’s operat-

ing display does not light

up.

The app on the receiving

device has a black

screen.

The transmitter does not

work.

Check whether the app responds:

Open the menu.

Check the transmitter connection and

function.

The receiving device cuts

off during image play-

back.

The connection between

transmitter and receiving

device is too weak.

Adjust the location of the transmitter by

a few centimetres.

VT50WiFi-IO-16s.book Seite 16 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Disposal

EN

17

11 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever possible.

M

If you wish to finally dispose of the product, ask your local recycling centre or specialist

dealer for details about how to do this in accordance with the applicable disposal

regulations.

12 Technical data

VT50WiFi

Ref. no.: 9600003262

Image sensor: CMOS

Pixels: 300000 pixels

Sensitivity: < 1 lux

Delay: 200 ms

Time needed to establish connection: < 10 s

Resolution: 640 x 480 pixels

WLAN frequency: 2412 – 2483.5 MHz

WLAN standard: WIFI 802.11 g/n (QPSK, 16QAM)

Transmission distance (direct vision): > 15 m

Operating voltage: 9 – 16 Vg

Amperage: 200 mA

Operating temperature: –20 °C to +70 °C

Camera dimensions (without assembly plate): 62 x 27 x 26 mm

Transmitter dimensions (without antenna): 45 x 47 x 20 mm

Weight (camera and transmitter): 150 g

VT50WiFi-IO-16s.book Seite 17 Mittwoch, 12. Dezember 2018 7:08 19

Erklärung der Symbole VT50WiFi

DE

18

Bitte lesen Sie diese Anleitung vor Einbau und Inbetriebnahme sorgfältig durch und

bewahren Sie sie auf. Geben Sie sie im Falle einer Weitergabe des Produktes an den

Nutzer weiter.

Inhaltsverzeichnis

1 Erklärung der Symbole. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2 Sicherheits- und Einbauhinweise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3 Lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4 Bestimmungsgemäßer Gebrauch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

5 Technische Beschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

6 Kamera und Sender montieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

7 Sender elektrisch anschließen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

8 VT50WiFi benutzen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

9 Störungsbeseitigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

10 Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

11 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

12 Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

1 Erklärung der Symbole

!

A

I

WARNUNG!

Sicherheitshinweis: Nichtbeachtung kann zu Tod oder schwerer Verletzung führen.

VORSICHT!

Sicherheitshinweis: Nichtbeachtung kann zu Verletzungen führen.

ACHTUNG!

Nichtbeachtung kann zu Materialschäden führen und die Funktion des Produktes

beeinträchtigen.

HINWEIS

Ergänzende Informationen zur Bedienung des Produktes.

VT50WiFi-IO-16s.book Seite 18 Mittwoch, 12. Dezember 2018 7:08 19

VT50WiFi Sicherheits- und Einbauhinweise

DE

19

2 Sicherheits- und Einbauhinweise

Der Hersteller übernimmt in folgenden Fällen keine Haftung für Schäden:

•

Beschädigungen am Produkt durch mechanische Einflüsse und Überspannungen

•

Veränderungen am Produkt ohne ausdrückliche Genehmigung vom Hersteller

•

Verwendung für andere als die in der Anleitung beschriebenen Zwecke

Beachten Sie die vom Fahrzeughersteller und vom Kfz-Handwerk vorgeschriebenen

Sicherheitshinweise und Auflagen!

!

WARNUNG!

Unzureichende Leitungsverbindungen können zur Folge haben, dass durch Kurzschluss

•

Kabelbrände entstehen,

•

der Airbag ausgelöst wird,

•

elektronische Steuerungseinrichtungen beschädigt werden,

•

elektrische Funktionen ausfallen (Blinker, Bremslicht, Hupe, Zündung, Licht).

A

ACHTUNG!

Klemmen Sie wegen der Kurzschlussgefahr vor Arbeiten an der Fahrzeugelektrik immer

den Minuspol ab.

Bei Fahrzeugen mit Zusatzbatterie müssen Sie an dieser ebenfalls den Minuspol

abklemmen.

Beachten Sie deshalb folgende Hinweise:

•

Verwenden Sie bei Arbeiten an den folgenden Leitungen nur isolierte Kabelschuhe, Stecker

und Flachsteckhülsen:

– 30 (Eingang von Batterie Plus direkt)

– 15 (Geschaltetes Plus, hinter Batterie)

– 31 (Rückleitung ab Batterie, Masse)

– L (Blinkerleuchten links)

– R (Blinkerleuchten rechts)

Verwenden Sie keine Lüsterklemmen.

•

Verwenden Sie eine Krimpzange zum Verbinden der Kabel.

•

Schrauben Sie das Kabel bei Anschlüssen an Leitung 31 (Masse)

– mit Kabelschuh und Zahnscheibe an eine fahrzeugeigene Masseschraube oder

– mit Kabelschuh und Blechschraube an das Karosserieblech.

Achten Sie auf eine gute Masseübertragung!

VT50WiFi-IO-16s.book Seite 19 Mittwoch, 12. Dezember 2018 7:08 19

Sicherheits- und Einbauhinweise VT50WiFi

DE

20

Beim Abklemmen des Minuspols der Batterie verlieren alle flüchtigen Speicher der Komfort-

elektronik ihre gespeicherten Daten.

•

Folgende Daten müssen Sie je nach Fahrzeugausstattung neu einstellen:

–Radiocode

–Fahrzeuguhr

– Zeitschaltuhr

– Bordcomputer

– Sitzposition

Hinweise zur Einstellung finden Sie in der jeweiligen Bedienungsanleitung.

Beachten Sie folgende Hinweise bei der Montage:

!

VORSICHT!

•

Befestigen Sie die im Fahrzeug montierten Teile so, dass sie sich unter keinen

Umständen (scharfes Abbremsen, Verkehrsunfall) lösen und zu Verletzungen der

Fahrzeuginsassen führen können.

•

Befestigen Sie verdeckt unter Verkleidungen anzubringende Teile des Systems so,

dass sie sich nicht lösen oder andere Teile und Leitungen beschädigen und keine

Fahrzeugfunktionen (Lenkung, Pedale usw.) beeinträchtigen können.

•

Beachten Sie immer die Sicherheitshinweise des Fahrzeugherstellers.

Einige Arbeiten (z. B. an Rückhaltesystemen wie Airbag usw.) dürfen nur von

geschultem Fachpersonal durchgeführt werden.

A

ACHTUNG!

•

Achten Sie beim Bohren auf ausreichenden Freiraum für den Bohreraustritt, um

Schäden zu vermeiden.

•

Entgraten Sie jede Bohrung und behandeln Sie diese mit Rostschutzmittel.

Beachten Sie folgende Hinweise bei der Arbeit an elektrischen Teilen:

A

ACHTUNG!

•

Benutzen Sie zum Prüfen der Spannung in elektrischen Leitungen nur eine Dioden-

prüflampe oder ein Voltmeter.

Prüflampen mit einem Leuchtkörper nehmen zu hohe Ströme auf, wodurch die

Fahrzeugelektronik beschädigt werden kann.

•

Beachten Sie beim Verlegen der elektrischen Anschlüsse, dass diese

– nicht geknickt oder verdreht werden,

– nicht an Kanten scheuern,

– nicht ohne Schutz durch scharfkantige Durchführungen verlegt werden.

•

Isolieren Sie alle Verbindungen und Anschlüsse.

•

Sichern Sie die Kabel gegen mechanische Beanspruchung durch Kabelbinder oder

Isolierband, z. B. an vorhandenen Leitungen.

VT50WiFi-IO-16s.book Seite 20 Mittwoch, 12. Dezember 2018 7:08 19

La page charge ...

Dometic PerfectView VT50WiFi Mode d'emploi

Ce manuel convient également à

Dometic PerfectView VT50WiFi Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents