JennAir ALOVE24RRC Guide d'installation

     l

COLUMN REFRIGERATION

MULTIPLE UNITS

     l at i o n

DE RÉFRIGÉRATEURS

PLUSIEURS UNITÉS

W10919013B

2 INTRODUCTION

IMPORTA NT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■ To avoid a hazard due to instability of the appliance, it must

be fixed in accordance with the instructions.

■ Plug into a grounded 3 prong outlet.

■ Installation shall be performed only by manufacturer, or an

authorized agent.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■

Disconnect power to all units before servicing.

■ Replace all parts and panels before operating.

■ Remove doors from your old refrigerator.

■ Use nonflammable cleaner.

■ Do not store or use petrol, flammable liquids or gas in the

vicinity of this or other electrical appliances. The fumes can

cause fires or explosions.

■

Do not store explosive substances such as aerosol cans

with a flammable propellant in this refrigerator.

■ Do not use or place electrical devices inside the refrigerator

compartments if they are not of the type expressly

authorized by the manufacture.

■ Use two or more people to move and install refrigerator.

■ Disconnect power before installing ice maker (on ice maker

kit ready models only).

■ A qualified service technician must install the water line and

ice maker. See installation instruction supplied with

ice maker kit IC13B for complete details.

■ Connect to a potable water supply only.

■ Use a sturdy glass when dispensing ice (on some models).

■ This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do not

play with the appliance.

■ To avoid the risk of children becoming trapped and

suffocating, do not allow them to play or hide inside

the refrigerator.

■ If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified person

in order to avoid a hazard.

■ This refrigerator is intended to be used in household and

similar applications such as:

– staff kitchen areas in shops, offices, and other working

environments

– farm houses and by clients in hotels, motels, and other

residential type environments

– bed and breakfast type environments

– catering and similar non-retail applications

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

INTRODUCTION 3

IMPORTANT: Child entrapment and

suffocation are not problems of the past.

Junked or abandoned refrigerators are still

dangerous – even if they will sit for "just a

few days." If you are getting rid of your old

refrigerator, please follow these instructions

to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children

may not easily climb inside.

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

4 INTRODUCTION

WHY WE LOVE

JENNAIR INSTALLERS

THEY’RE TOTAL PROFESSIONALS AND PERFECTIONISTS.

It’s all about getting that seamless ﬂush execution, that down-to-the-millimeter adjustment. Flawless

installation is incredibly important to the function, appearance and lifetime enjoyment of our products, and

our installers make it happen every day.

THEY DO THEIR HOMEWORK. AND HELP US WITH OURS.

These experts know JennAir

®

products inside and out. They train extensively on JennAir installation, learning

the latest techniques and insider tips so they can install our cutting edge appliances with ease. And we

value their input, incorporating installer feedback to reﬁne and perfect our installations.

THEY THINK THROUGH EVERY DETAIL OF THE EXPERIENCE.

Above and beyond dedication is the baseline. The JennAir experience starts the minute an installer brings

the customer’s column home. Keeping the site spotless, taking extreme care with both the appliances and

the home and providing an unforgettable introduction to columns is all part of the game plan.

With the launch of the ﬁrst ever JennAir

®

columns, we reimagined the entire columns

installation process, eliminating problems that affect our sub-par competitors. Some of the

features professional installers are most excited about:

• Concealed six-point panel adjustment

Easy and precise alignment

• Site-tailored Rotter system shims

and badass bracket

Guide and keep column in position

• Precision four-point front leveling

On sturdy rollers that easily bear full weight

EASE. SPEED. SAFETY.

• Metal fascia

Increases durability

• Solid wood core stainless steel panels

Easy to prep and hang and do not

require drilling through steel

• Expanded utility areas

Reduced changes to replace built-ins

or upgrade from competitor columns

And with your help, we’ll just keep getting better.

Contact the JennAir Epicenter through jennair.com or at 1-800-JENNAIR (536-6247)

to report installation tips and tricks, or to consult with experts who know

the installation process inside and out.

INTRODUCTION 5

TABLE OF CONTENTS

INTRODUCTION

02 SAFETY INSTRUCTIONS

06 TOOLS & PARTS

08 JOIN KITS

11 CONFIGURATIONS

13 PRODUCT DIMENSIONS

15 DOOR STYLE

16 OPENING DIMENSIONS

21 SITE PREP

24 INSTRUCTION KEY

PREPARATION

25 SECTION 1  PREPARE COLUMNS

32 SECTION 2  PREPARE JOIN KIT

37 SECTION 3  PREPARE POSITIONING BRACKET

40 SECTION 4  BADASS BRACKET INSTALLATION

49 SECTION 5  PREPARE FURNITURE

INSTALLATION

55 SECTION 6  FIRST COLUMN INSTALLATION

65 SECTION 7  SECOND COLUMN INSTALLATION

73 SECTION 8  THIRD COLUMN INSTALLATION

81 SECTION 9  PREPARE COLUMN FOR USE

ACCESSORIES

87 SECTION 10  TOEKICK: CUSTOM WOOD PREPARATION

90 SECTION 11  TOEKICK: STAINLESS STEEL PREPARATION

93 SECTION 12  TOEKICK: ALIGN AND INSTALL

98 SECTION 13  PANEL: CUSTOM WOOD PREPARATION

103 SECTION 14  PANEL: STAINLESS STEEL PREPARATION

106 SECTION 15  PANEL: HANG AND ALIGN

COMPLETE

113 SECTION 16  COMPLETE INSTALLATION

116 FINAL CHECKLIST

120 TABLE DES MATIÈRES

6 INTRODUCTION

TOOLS + PARTS

PROVIDED

READ AND FOLLOW THE INSTRUCTIONS PROVIDED WITH

ANY OF THE TOOLS LISTED.

TOOLS + PARTS

PROVIDED

Five installation shims

(W10913387)

#2 Square-drive screws

(3-24004-079)

8-18 x 3/4

Phillips head screws

(W11041176)

6-20 x .375 screws

(246131)

5 mm driver bit

(W11121505)

3 mm driver bit

(W11121512)

Shim installation template

(W11040585)

3MM

5MM

Toe-kick and door panel installation template

(W11040865)

3 mm

†

Allen® wrench

5 mm Allen® wrench

Gripping pads

(W10840464)

†®

Allen is a registered trademark of Apex Brands, Inc.

INTRODUCTION 7

TOOLS + PARTS

NOT PROVIDED

TOOLS



Cordless drill and drill bits or impact driver



Drill bit set including 3/32" and 1/8" diameter bits



Two adjustable wrenches



#2 Phillips bit



1/4" magnetic nut driver



#2 square-drive bit



48" or longer level or straight edge

(Can substitute a factory-installed trim

piece, once removed.)



3/8" and 1/2" open-end wrenches



Tape measure



Utility knife



Masking tape



Appliance dolly



Right angle drill adapter



6" drill extension



#8 pan head wood screws of assorted lengths

including 1", 1-1/4", 1-1/2"

PARTS



Flexible code-approved water supply line



Custom door overlay panels

• Stainless steel panels: order from JennAir

• Custom wood panels: consult a qualiﬁed

cabinetmaker or carpenter



Additional fasteners will be required according

to the kitchen furniture construction

WHY USE

ROTTER

SYSTEM

SHIMS

AND THE

BADASS

BRACKET?

9/32"

1/4"

3/16" 1/8"

1/16"

This recommended process might be unfamiliar to

you as an installer, but it adds enormous value to both

you and your client. Use the Rotter system to:

• Help position column without scratching

• Create precise 1/8" reveals on each side

• Always have ready-made shims tailored to each site

• Keep column stable in cutout over lifetime

• Eliminate misalignment issues for your client

8 INTRODUCTION

JOIN KITS

SOLD SEPERATELY

READ AND FOLLOW THE INSTRUCTIONS PROVIDED WITH

ANY OF THE TOOLS LISTED.

(17) Flat washers

(8534057)

10-13 x PN CR

(W11117666)

10-13 x 2.0 FL CR

Join kit spacer

(W11111782)

8-18 x MFI 6L HL SS BLK

(W11117377)

Handle-to-handle join kit

(JAJ13HSS)

Hinge-to-handle join kit

(JAJ12HSS)

Handle-to-hinge join kit

(JAJ11HSS)

Burlesque Handle-to-handle join kit

(JAJ14JSS)

TOOLS AND PARTS INCLUDED IN JOIN KITS

INTRODUCTION 9

Badass soffit bracket

(W11111754)

Positioning bracket

(W11111771)

JOIN KITS

SOLD SEPERATELY

READ AND FOLLOW THE INSTRUCTIONS PROVIDED WITH

ANY OF THE TOOLS LISTED.

Soffit bracket installation template

(W11040584)

ALLIGNMENT TO THE

CABINET FACE

FRAME

Peel and stick heating pad

(W10912090)

(8) M6-1 x 6 10 mm metric hex nuts

(W10854505)

(14) 8-15 x “L” Mtr cr cone screws

(8281252)

Positioning bracket mount

(W11111772)

TOOLS AND PARTS INCLUDED IN JOIN KITS CONTD.

10 INTRODUCTION

JOIN KITS

SOLD SEPERATELY

TOOLS AND PARTS INCLUDED IN JOIN KITS CONTD.

Handle-to-handle join kit

Left-hand (handle) trim

(W11103734)

Right-hand (handle) trim

(W11103737)

Handle-to-hinge join kit

Left-hand (handle) trim

(W11103734)

Right-hand (hinge) trim

(W11103736)

Hinge-to-handle join kit

Left-hand (handle) trim

(W11103737)

Right-hand (hinge) trim

(W11103735)

INTRODUCTION 11

CONFIGURATIONS

2UNITS

PERMISSABLE 2UNIT CONFIGURATIONS

NONPERMISSABLE 2UNIT CONFIGURATIONS

Hinge-to-hinge

Pinch Hazard

Installation of door panels with less than a 3/8"

(0.95 cm) gap between the door panel and the

adjacent cabinet increases the risk of potential

pinching.

CAUTION

Hinge-to-handle

join kit

(JAJ12HSS)

Handle-to-handle

join kit

(JAJ13HSS)

Handle-to-hinge

join kit

(JAJ11HSS)

X

12 INTRODUCTION

CONFIGURATIONS

3UNITS

PERMISSABLE 3UNIT CONFIGURATIONS

NONPERMISSABLE 3UNIT CONFIGURATIONS

Handle-to-hinge and

handle-to-hinge

join kits:

JAJ11HSS (X2)

Hinge-to-hinge

Handle-to-hinge and

handle-to-handle

join kits:

JAJ11HSS and JAJ13HSS

Hinge-to-handle and

hinge-to-handle

join kits:

JAJ12HSS (x2)

Hinge-to-hinge

Handle-to-handle and

hinge-to-handle

join kits:

JAJ13HSS and JAJ12HSS

X X

INTRODUCTION 13

DIMENSIONS

PRODUCT

OVERALL PRODUCT NO PANEL

Width See unit width table below

Height 79-7/8" – 85-5/16" (202.9 – 215.9 cm)

Depth 24-1/8" (61.3 cm)

Raw Door Height 79-7/8" (202.9 cm)

Toe-kick Height 3-9/16" (9.1 cm)

Toe-kick Depth 3-1/4" – 4-7/8" (8.3 – 12.4 cm)

PRODUCT WIDTH

Model Width

18"

JBZFR18IGX

JBZFL18IGX

ALOVE18FL

17-3/4"

(45.1 cm)

24"

JBRFR24IGX

JBRFL24IGX

JBZFR24IGX

JBZFL24IGX

ALOVE24FL

ALOVE24RR

23-3/4"

(60.3 cm)

30"

JBRFR30IGX

JBRFL30IGX

JBZFR30IGX

JBZFL30IGX

ALOVE30RR

29-3/4"

(75.6 cm)

36"

JBRFR36IGX

JBRFL36IGX

35-3/4"

(90.8 cm)

Width varies

(See table)

83-1/2"

24-1/8"

14 INTRODUCTION

DIMENSIONS

ACCESSORIES

CUSTOM TOEKICK

Height 3-9/16" (9.1 cm)

Thickness 3/16"-3/4" (4.8 – 1.9 mm)

STAINLESS STEEL PANEL

Height 80" (203.2 cm)

Thickness 13/16" (2.1 cm)

CUSTOM PANEL

Thickness 3/4" (1.9 cm) max.

Weight 60 lbs. (27.2 kg) max.

Typical Height 80" (203.2 cm)

INTRODUCTION 15

MODEL FLUSH WIDTH

18" 17-3/4" (45.1 cm)

24" 23-3/4" (63.5 cm)

30" 29-3/4" (75.6 cm)

36" 35-3/4" (90.8 cm)

Furniture

Panel

PanelPanel

MODEL FLUSH WIDTH

18" 17-3/4" (45.1 cm)

24" 23-3/4" (63.5 cm)

30" 29-3/4" (75.6 cm)

36" 35-3/4" (90.8 cm)

MODEL OVERLAY WIDTH

18" 18-3/8" (46.7 cm)

24" 24-3/8" (61.9 cm)

30" 30-3/8" (77.2 cm)

36" 36-3/8" (92.4 cm)

1/6"

Furniture

Panel

DOOR STYLE

CUSTOM PANEL WIDTH

1/6"

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap

between the door panel and the adjacent cabinet increases

the risk of potential pinching.

CAUTION

Panel

1/6"

5/8"

Furniture

Panel

5/8"

Panel

1/6"

16 INTRODUCTION

DIMENSIONS

OPENING

42"

CUTOUT WIDTH

18" 24"

48"

CUTOUT WIDTH

18" 30"

48"

CUTOUT WIDTH

24" 24"

36"

CUTOUT WIDTH

18" 18"

66"

CUTOUT WIDTH

30" 36"

72"

CUTOUT WIDTH

36" 36"

54"

CUTOUT WIDTH

18" 36"

54"

CUTOUT WIDTH

24" 30"

60"

CUTOUT WIDTH

36"24" 30"

60"

CUTOUT WIDTH

30"

2UNIT CONFIGURATIONS

NOTE: These diagrams show cutout width of product combinations.

Products may be arranged into any permissable conﬁguration shown on pg. 10-11.

INTRODUCTION 17

DIMENSIONS

OPENING

54"

CUTOUT WIDTH

18" 18" 18"

60"

CUTOUT WIDTH

18" 18" 24"

66"

CUTOUT WIDTH

66"

CUTOUT WIDTH

18" 18" 30"

66"

CUTOUT WIDTH

18" 24" 24"

72"

CUTOUT WIDTH

18" 18"

36"

72"

CUTOUT WIDTH

18" 24" 30"

72"

CUTOUT WIDTH

24" 24" 24"

78"

CUTOUT WIDTH

18" 24" 36"

78"

CUTOUT WIDTH

24" 24" 30"

78"

CUTOUT WIDTH

18" 30" 30"

3UNIT CONFIGURATIONS

NOTE: These diagrams show cutout width of product combinations.

Products may be arranged into any permissable conﬁguration shown on pg. 10-11.

18 INTRODUCTION

DIMENSIONS

OPENING

3UNIT CONFIGURATIONS

84"

CUTOUT WIDTH

18" 30" 36"

84"

CUTOUT WIDTH

24" 24" 36"

84"

CUTOUT WIDTH

24" 30" 30"

90"

CUTOUT WIDTH

30" 30" 30"

90"

CUTOUT WIDTH

24" 30" 36"

90"

CUTOUT WIDTH

18" 36" 36"

96"

CUTOUT WIDTH

24" 36" 36"

96"

CUTOUT WIDTH

30" 30" 36"

36"

102"

CUTOUT WIDTH

30" 36"

108"

CUTOUT WIDTH

36" 36" 36"

NOTE: These diagrams show cutout width of product combinations.

Products may be arranged into any permissable conﬁguration shown on pg. 10-11.

INTRODUCTION 19

B

C

D

A

DIMENSIONS

OPENING

Model 115º Door Swing "A" 90º Door Swing "B" Wall Gap "C" Door Open Depth "D"

18" 10-1/2" (26.7 cm) 5" (12.7 cm) 2-1/2" (6.4 cm) 44-1/2" (113 cm)

24" 13" (33 cm) 5" (12.7 cm) 2-1/2" (6.4 cm) 50-1/2" (128.3 cm)

30" 15-1/2" (39.4 cm) 5" (12.7 cm) 2-1/2" (6.4 cm) 56-3/8" (143.2 cm)

36" 18" (45.7 cm) 5" (12.7 cm) 2-1/2" (6.4 cm) 62-7/16" (158.6 cm)

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap

between the door panel and the adjacent cabinet increases

the risk of potential pinching.

CAUTION

DOOR SWING REQUIREMENTS

Dimensions give 2-1/2" spacing between stainless steel handle accessory and wall to avoid pinching.

For a custom wood panel, consider handle depth to maintain 2-1/2" spacing.

20 INTRODUCTION

DIMENSIONS

OPENING

OPENING WIDTH

Model Width (A)

18"

JBZFR18IGX

JBZFL18IGX

ALOVE18FL

18"

(45.7 cm)

24"

JBRFR24IGX

JBRFL24IGX

JBZFR24IGX

JBZFL24IGX

ALOVE24FL

ALOVE24RR

24"

(61 cm)

30"

JBRFR30IGX

JBRFL30IGX

JBZFR30IGX

JBZFL30IGX

ALOVE30RR

30"

(76.2 cm)

36"

JBRFR36IGX

JBRFL36IGX

36"

(91.4 cm)

10"

84"

25"

*

*24" with 24" trim kit

Width (A)

Furniture

return

Soft

8"

La page charge ...

JennAir ALOVE24RRC Guide d'installation

JennAir ALOVE24RRC Guide d'installation

dans d''autres langues

Documents connexes

Autres documents