Hamilton Beach 19701 Mode d'emploi

READ BEFORE USE

LIRE AVANT UTILISATION

LEA ANTES DE USAR

Questions?

Please call us – our friendly

associates are ready to help.

USA: 1.800.851.8900

¿Preguntas?

Por favor llámenos – nuestros

amables representantes están

listos para ayudar.

MEX: 01 800 71 16 100

Le invitamos a leer cuidadosamente

este instructivo antes de usar su

aparato.

Visit www.hamiltonbeach.com for our

complete line of products and Use and

Care Guides – as well as

delicious recipes, tips, and

to register your product online!

Rendez-vous sur www.hamiltonbeach.ca

pour notre liste complète de produits et de

nos manuels utilisateur – ainsi que nos

délicieuses recettes, nos conseils et pour

enregistrer votre produit en ligne !

¡Visite www.hamiltonbeach.com.mx para

obtener nuestra línea completa de productos

y las Guías de Uso y Cuidado, además de

deliciosas recetas, consejos y para registrar

su producto en línea!

Questions ?

N’hésitez pas à nous appeler –

nos associés s’empresseront

de vous aider.

CAN : 1.800.267.2826

Durathon

TM

Iron

Fer à repasser

Plancha

English ...................... 2

Français .................. 15

Español ................... 29

840221004 ENv01.indd 1840221004 ENv01.indd 1 4/22/14 3:36 PM4/22/14 3:36 PM

2

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING

1. Only use an iron for its intended use.

2. To avoid the risk of electric shock, do not immerse the iron

in water or other liquids.

3. Always turn the iron to OFF before plugging or unplugging

the iron from the electrical outlet. Never pull on the cord to

disconnect the iron from the electrical outlet; instead, grasp

the plug and pull on the plug to disconnect the iron.

4. Do not let the cord touch hot surfaces. Let the iron cool

completely before putting the iron away. Coil the cord in

the provided cord wrap or, if option not provided, coil the

cord loosely around the iron for storing.

5. Always disconnect the iron from the electrical outlet before

filling the iron with water, emptying the water from the iron,

and when the iron is not in use.

6. Do not operate the iron with a damaged cord or in the event

the iron has been dropped or damaged or there are visible signs

of damage or it is leaking. To avoid the risk of electric shock, do

not disassemble the iron. Take it to a qualified serviceman for

examination and repair. Incorrect assembly might result in a risk

of electric shock when the iron is used after reassembly.

7. The iron must be used and rested on a stable surface.

8. When placing the iron on its stand, ensure that the surface

on which the stand is placed is stable.

9. Close supervision is required for any appliance used by or near

children. Do not leave the iron unattended while the iron is

connected or on an ironing board.

10. Burns can occur from touching hot metal parts, hot water, or

steam. Use caution when you turn a steam iron upside down—

there might be hot water in the reservoir.

11. To avoid a circuit overload, do not operate an iron on the same

circuit with another high-wattage appliance.

12. If an extension cord is absolutely necessary, a cord with an

ampere rating equal to or greater than the maximum rating of

the iron shall be used. A cord rated for less amperage can result

in a risk of fire or electric shock due to overheating. Care shall be

taken to arrange the cord so that it cannot be pulled or be tripped

over.

When using your flatiron, basic safety precautions should always be followed, including the following:

840221004 ENv01.indd 2840221004 ENv01.indd 2 4/22/14 3:36 PM4/22/14 3:36 PM

3

Other Consumer Safety Information

This product is intended for household use only.

WARNING! Shock Hazard: This appliance has a polarized plug (one

wide blade) that reduces the risk of electric shock. The plug fits only

one way into a polarized outlet. Do not defeat the safety purpose of

the plug by modifying the plug in any way or by using an adapter.

If the plug does not fit fully into the outlet, reverse the plug. If it still

does not fit, have an electrician replace the outlet.

• Use the iron on an ironing board. Ironing on any other surface

may damage that surface.

• Do not iron or vertical-steam clothes that are being worn.

• Do not use vertical steam in the direction of people or pets.

• During first use of the iron, it may appear to smoke. This will

stop and does not indicate a defect or hazard.

• Many irons spit or sputter during the first few uses with tap

water. This happens as the steam chamber becomes conditioned.

This will stop after a few uses.

• To clean steam vents before first use, prepare iron for steam

ironing and then iron over an old cloth for a few minutes while

letting the iron steam. Press the Steam Burst button several times

to clean the vents. Then follow the self-cleaning instructions on

page 11.

840221004 ENv01.indd 3840221004 ENv01.indd 3 4/22/14 3:36 PM4/22/14 3:36 PM

Parts and Features

Heel Rest

Water Tank

Cover

Cord

Self-Clean

Button

Durathon™ Nonstick Soleplate

Spray

Nozzle

Spray and Steam

Burst Buttons

Adjustable

Steam Switch

Temperature

Control Dial

Auto Shutoff/

Power ON Light

Optional Features

(on select models)

Cord Wrap

Retractable Cord

Soft Touch Grip

4

840221004 ENv01.indd 4840221004 ENv01.indd 4 4/22/14 3:36 PM4/22/14 3:36 PM

How to Dry Iron

1 2 3 4

Set the Adjustable Steam Switch

to (Dry Iron).

Turn Temperature Control Dial

to desired temperature. Allow 2

minutes for iron to reach desired

temperature.

To turn iron off, turn Temperature

Control Dial to OFF.

5

6

IRON POSITION

Resting on soleplate

Resting on either side

Resting on heel

POSITION SENSING/AUTO SHUTOFF

The iron will turn off automatically when left in the following positions.

The Auto Shutoff time varies based on the iron’s position.

MOTIONLESS TIME

30 seconds

15 minutes

NOTE: Moving the iron will reset the Auto Shutoff sensor.

NOTE: Fully unwrap cord from

cord wrap if provided.

5

840221004 ENv01.indd 5840221004 ENv01.indd 5 4/22/14 3:36 PM4/22/14 3:36 PM

How to Steam Iron

2

4

5

Set the Adjustable Steam Switch

to (Dry Iron).

Turn Temperature Control Dial

to desired fabric setting in the

steam range. Allow 2 minutes for

iron to reach desired temperature.

WARNING! Burn Hazard:

Attempting to steam iron on

a lower temperature setting or

failing to allow the iron to preheat

for 2 minutes can result in hot

water dripping from the soleplate.

Set Adjustable Steam Switch to

the desired steam level.

1

3

6 6

For vertical steaming, hold iron 6 inches (15 cm) from garment and do

not allow hot soleplate to touch delicate garments. Press and release

the Steam Burst Button to steam out wrinkles. Wait at least 5 seconds

before pressing Steam Burst Button again.

OR

6

NOTE: Fully unwrap cord from

cord wrap if provided.

840221004 ENv01.indd 6840221004 ENv01.indd 6 4/22/14 3:36 PM4/22/14 3:36 PM

How to Steam Iron (cont.)

To turn iron off, set Adjustable

Steam Switch to (Dry Iron).

7 8

Turn the Temperature Control

Dial to OFF.

9 10

Unplug iron and let cool. Empty water from iron following

directions in “Care and Cleaning.”

IRON POSITION

Resting on soleplate

Resting on either side

Resting on heel

POSITION SENSING/AUTO SHUTOFF

The iron will turn off automatically when left in the following positions.

The Auto Shutoff time varies based on the iron’s position.

MOTIONLESS TIME

30 seconds

15 minutes

NOTE: Moving the iron will reset the Auto Shutoff sensor.

7

840221004 ENv01.indd 7840221004 ENv01.indd 7 4/22/14 3:36 PM4/22/14 3:36 PM

Fabric Setting Chart

NOTICE: To avoid garment damage, check garment label for

fabric composition and ironing instructions.

Garment Label Symbols

Fabric care labels on garments have symbols that show ironing

instructions and recommended temperature settings. These symbols

are shown below along with an explanation of their meaning.

Temperature

Setting

OFF

Synthetics

Silk, Wool

Cotton, Linen

Steam

Setting

Dry

Iron

Steam

Range

Ironing

Instructions

OFF

Dry iron using spray

if necessary.

Iron silk on wrong

side.

For cotton, iron

while still damp or

use spray.

For linen, iron fabric

on wrong side.

•

Low

••

Medium

•••

High

Iron

High

Temp

Setting

Medium

Temp

Setting

Low Temp

Setting

Do not iron

Do not use

steam

8

840221004 ENv01.indd 8840221004 ENv01.indd 8 4/22/14 3:36 PM4/22/14 3:36 PM

Tips for Best Ironing Results

PREPARE TO IRON:

1. Cover your ironing board with a padded, heat-resistant cover. Brush or wipe off any dust, dirt, or debris so it doesn’t end up on your clothes.

2. To set the height of the ironing board, stand with your elbows bent at right angles; then drop your hands slightly so that your arms are in a

comfortable position. Set the height of your ironing board to this height.

3. Check the soleplate (the surface of the iron that meets the fabric) for mineral deposits or scorched material before you begin ironing. If these

deposits or minerals are left on the soleplate, they may end up on your clothes. Unsure? Test-glide the iron on a rag or old towel first.

TEST KITCHEN TIP: To clean an iron’s soleplate, preheat the iron to the highest temperature setting and iron over a damp, 100% cotton cloth.

This creates heavy steam that transfers grime from the soleplate to the cloth. Many irons have a Self-Clean Button. This will clean the steam

holes, but it will not remove grime from the flat surface of the soleplate. NOTE: Care should be used while cleaning; steam can burn.

FAST FACTS:

• Don’t iron in a circular motion as this can stretch fabric. Instead, iron lengthwise.

• Natural fibers such as cotton and linen should be ironed slightly damp for faster, easier ironing. If they are completely dry, use maximum

steam while ironing or mist them with water prior to ironing.

• Any portion of a garment that has 2 layers of fabric such as pockets, seams, collars, and cuffs should be ironed inside out first.

• To press a collar, iron from the points in using small strokes of the iron. After wrinkles are pressed out, crease the collar into place by hand—

not with the iron. Treat French cuffs similarly, gently creasing by hand after ironing.

IRONING VERSUS PRESSING:

• You may have heard the terms “ironing” and “pressing” used interchangeably, but they are actually quite different. When ironing, you slide the

iron back and forth over fabric. When pressing, the iron is placed and held on the fabric in one spot, lifted up, and this process is repeated until

the areas that need attention are smooth. A “pressing” technique is helpful to avoid stretching fabrics.

• A pressing cloth can help reduce unwanted “shine” on fabrics. You can purchase a pressing cloth in the laundry care section, or a clean white

dishtowel or 100% cotton pillowcase works equally well. You do not need to increase the recommended iron temperature when using a

pressing cloth.

FABRIC FACTS AND LABELS:

Every fabric is different and should be treated accordingly. The label inside clothing or linens should recommend fabric care instructions that

include ironing treatment. As a general rule, these instructions should be followed. If the fabric is a blend, use a low temperature setting. If you

do not know what the content of the fabric is, use the lowest temperature first and test on an inside seam.

9

840221004 ENv01.indd 9840221004 ENv01.indd 9 4/22/14 3:36 PM4/22/14 3:36 PM

Care and Cleaning

1

Allow iron to cool.

To clean an iron’s soleplate, preheat the iron to the highest

temperature setting and iron over a damp, 100% cotton cloth.

This creates heavy steam that transfers grime from the soleplate

to the cloth. Many irons have a Self-Clean Button. This will clean

the steam holes, but it will not remove grime from the flat surface

of the soleplate.

NOTE: Care should be used while cleaning; steam can burn.

NOTICE: To avoid damage to the iron soleplate:

• Never iron over zippers, buttons, pins, metal rivets, or snaps,

since they may scratch the soleplate surface.

• Allow the iron to cool and wipe with a soapy, soft damp

cloth to clean occasional buildup on the soleplate. Never use

abrasive cleaners or metal scouring pads, since they may

scratch the surface.

To empty water from iron, open

the water tank cover and slowly

tilt pointed end of iron over sink

until water runs out.

CORD WRAP RETRACTABLE CORD

Optional feature on select

models.

Optional feature on select

models.

CAUTION: Hold plug while

retracting cord. Do not unwind

the cord past the red tape on

the cord.

Soleplate Care

10

2

840221004 ENv01.indd 10840221004 ENv01.indd 10 4/22/14 3:36 PM4/22/14 3:36 PM

5 6

7

Self-Clean Feature

To keep the steam vents clear of any buildup, follow these

instructions each time you iron using steam.

1 2

3

Press and hold the Self-Clean

Button until tank is empty.

Turn Temperature Control Dial to

Cotton-Linen ••• setting and let

iron heat for 2 minutes.

Hold iron over sink.

11

4

840221004 ENv01.indd 11840221004 ENv01.indd 11 4/22/14 3:36 PM4/22/14 3:36 PM

Troubleshooting

PROBLEM

Iron won’t heat.

Water is leaking.

Iron won’t steam.

Iron leaves spots

on clothing.

Twisted cord.

Wrinkles not removed.

Iron too hot/not hot

enough.

PROBABLE CAUSE

• Is iron plugged in and the outlet working? Check outlet by plugging in a lamp.

• Is the Temperature Control Dial turned to a fabric setting?

• Is the Auto Shutoff/Power ON Light illuminated? Move the iron to reset.

• Do not overfill the water tank.

• Adjust steam to a lower setting.

• Is the Temperature Control Dial in the steam range? Did the iron have enough time to preheat?

• If dry ironing, make sure the Adjustable Steam Switch is in the (Dry Iron) position.

• Check water level.

• Is the Adjustable Steam Switch in the (Steam) position?

• Has the iron had enough time to preheat?

• Anti-drip feature will not allow steam when temperature setting is in the dry range.

• ALWAYS empty water tank after using. Water left in tank may discolor clothing and soleplate.

• If the iron cord should become twisted, unplug iron and let cool. Hold iron cord in the middle

of entire length. Let plug and iron dangle freely until cord uncoils. This will extend the life of

the iron cord.

• Check Temperature Control Dial is set to correct fabric.

• Check Temperature Control Dial and adjust to desired setting. Let iron cool down 5 minutes

before continuing.

12

840221004 ENv01.indd 12840221004 ENv01.indd 12 4/22/14 3:36 PM4/22/14 3:36 PM

13

Notes

840221004 ENv01.indd 13840221004 ENv01.indd 13 4/22/14 3:36 PM4/22/14 3:36 PM

14

Limited Warranty

This warranty applies to products purchased and used in the U.S. and Canada. This is the only express warranty for this product and

is in lieu of any other warranty or condition.

This product is warranted to be free from defects in material and workmanship for a period of one (1) year from the date of original

purchase; in addition, the Durathon™ nonstick covering on the soleplate is warranted not to wear out for a period of ten (10)

years from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or any

component found to be defective, at our option; however, you are responsible for all costs associated with returning the product

to us and our returning a product or component under this warranty to you. If the product or component is no longer available,

we will replace with a similar one of equal or greater value.

This warranty does not cover glass, filters, wear from normal use, use not in conformity with the printed directions, or damage to

the product resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or

gift recipient. Keep the original sales receipt, as proof of purchase is required to make a warranty claim. This warranty is void if the

product is used for other than single-family household use or subjected to any voltage and waveform other than as specified on the

rating label (e.g., 120V ~ 60 Hz).

We exclude all claims for special, incidental, and consequential damages caused by breach of express or implied warranty. All

liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition

of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such

warranty or condition is limited to the duration of this written warranty. This warranty gives you specific legal rights. You may have

other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or

special, incidental, or consequential damages, so the foregoing limitations may not apply to you.

To make a warranty claim, do not return this appliance to the store. Please call 1.800.851.8900 in the U.S. or 1.800.267.2826 in Canada

or visit hamiltonbeach.com in the U.S. or hamiltonbeach.ca in Canada. For faster service, locate the model, type, and series numbers

on your appliance.

840221004 ENv01.indd 14840221004 ENv01.indd 14 4/22/14 3:36 PM4/22/14 3:36 PM

CONSERVER CES INSTRUCTIONS

MEASURES DE SÉCURITÉ IMPORTANTES

LIRE TOUTES LES INSTRUCTIONS

AVANT L’UTILISATION

1. Utiliser exclusivement le fer pour son usage prévu.

2. Pour éviter le risque de choc électrique, ne pas plonger

le fer dans l’eau ou d’autres liquides.

3. Toujours mettre le fer sur ARRÉT avant de le brancher ou

débrancher de la prise électrique. Ne jamais tirer sur le cordon

pour déconnecter le fer de la prise électrique ; au lieu de cela,

saisir la fiche et tirer dessus pour débrancher le fer.

4.

Ne pas laisser le cordon toucher les surfaces chaudes. Laisser

refroidir le fer complètement avant de le remiser.

Enrouler le

cordon autour du rembobineur, si cette option est fournie,

ou enrouler lâchement le cordon autour du fer à repasser

pour ranger.

5. Toujours débrancher le fer de la prise électrique avant de remplir

le fer d’eau et de vider l’eau du fer, et lorsque le fer ne sert pas.

6. Ne pas utiliser le fer avec un cordon endommagé, si le fer est

tombé ou endommagé, s’il y a des signes visibles de dommage

ou s’il fuit. Pour éviter le risque de choc électrique, ne pas

démonter le fer. Le faire examiner et réparer par un dépanneur

qualifié. Un assemblage incorrect risque d’entraîner un risque de

choc électrique lorsque le fer est utilisé après réassemblage.

7. Le fer doit être utilisé et reposé sur une surface stable.

8. En plaçant le fer sur son support, assurez-vous que la surface

sur laquelle le support est placé est stable.

9. Une surveillance étroite est requise pour tout appareil utilisé par

ou près d’enfants.

Ne pas laisser le fer sans surveillance pendant

qu’il est branché ou pendant qu’il est sur une planche à repasser.

10.

Des brûlures peuvent survenir lorsqu’on touche des pièces

chaudes en métal, de l’eau chaude ou de la vapeur. Adopter des

précautions lorsqu’on tourne un fer à vapeur à l’envers, car il peut

rester de l’eau chaude dans le réservoir.

11. Pour éviter une surcharge du circuit, ne pas utiliser le fer sur le

même circuit qu’un autre appareil de haute puissance.

12. Si une rallonge électrique est absolument nécessaire, un cordon

d’intensité nominale égale ou supérieure à l’intensité nominale

maximale du fer doit être utilisé. Un cordon d’une

intensité

nominale moindre peut entraîner un risque d’incendie

ou de choc

électrique en raison d’une surchauffe.

Il faut prendre soin de

placer le cordon de rallonge pour qu’il ne puisse pas être tiré

par des enfants ou faire trébucher.

Lors de l’utilisation de votre fer à repasser, des précautions préliminaires de sécurité doivent toujours être observées, y compris ce qui suit :

15

840221004 FRv01.indd 15840221004 FRv01.indd 15 4/22/14 3:37 PM4/22/14 3:37 PM

16

Autres renseignements de sécurité aux consommateurs

Cet appareil est conçu pour une utilisation domestique seulement.

AVERTISSEMENT ! Risque d’électrocution : Cet appareil est doté

d’une fiche polarisée (lame large) qui réduit le risque d’électrocution.

Cette fiche s’insère d’une seule manière dans une prise polarisée.

Ne pas transformer le dispositif de sécurité de la fiche en modifiant

celle-ci de quelconque façon ou en utilisant un adaptateur. Si la fiche

refuse de s’insérer, inversez-la. Si elle refuse toujours de s’insérer,

faites remplacer la prise par un électricien.

• Utilisation du fer sur une planche à repasser. L’utilisation du fer

sur un autre type de surface peut endommager cette surface.

• Ne pas repasser ou repasser à la vapeur à la verticale les

vêtements que vous portez.

• Ne pas repasser à la vapeur en direction des gens ou des animaux.

• Lors de la première utilisation du fer à repasser, il peut sembler

émettre de la fumée. Ceci cessera et n’indique pas un défaut ou

un danger.

• Lors des premières utilisations avec de l’eau du robinet, de

nombreux fers crachent. Ceci se produit durant le conditionnement

de la chambre de vapeur. Ce phénomène cesse après quelques

utilisations.

• Pour nettoyer les évents de vapeur avant la première utilisation,

préparer le fer pour un repassage à la vapeur puis repasser un linge

usagé pendant quelques minutes en permettant l’échappement de

vapeur du fer. Appuyer sur le bouton de surpuissance de vapeur

à plusieurs reprises pour nettoyer les évents. Effectuer ensuite un

autonettoyage en suivant les instructions de la page 25.

840221004 FRv01.indd 16840221004 FRv01.indd 16 4/22/14 3:37 PM4/22/14 3:37 PM

17

Pièces et caractéristiques

Talon d’appui

Couvercle de

réservoir d’eau

Cordon

Bouton d’autonettoyage

Semelle antiadhésive Durathon

MC

Vaporisateur

Boutons de surpuissance

de vapeur et de vaporisation

Commutateur de

réglage de la vapeur

Cadran de commandes

de température

Arrêt automatique/

Voyant d’alimentation

Caractéristiques en option

(sur certains modèles)

Rembobineur de cordon

Cordon rétractable

Poignée douce

840221004 FRv01.indd 17840221004 FRv01.indd 17 4/22/14 3:37 PM4/22/14 3:37 PM

Repassage à sec

1 2 3 4

Régler le commutateur de

réglage de la vapeur à

(repassage à sec).

Tourner le cadran de commandes

de température au degré désiré.

Laisser chauffer le fer pendant

2 minutes pour qu’il atteigne la

température désirée.

Positionner le cadran de commandes

de température à OFF (arrêt) pour

mettre le fer hors tension.

5

6

POSITION DU FER

Repos sur la semelle

Repos sur le côté

Repos sur talon

DÉTECTION DE MOUVEMENT/MISE HORS TENSION AUTOMATIQUE

Le fer se coupe automatiquement lorsqu’il est laissé dans les positions

suivantes. La durée de mise hors tension automatique varie selon la

position du fer.

TEMPS D’IMMOBILISATION

30 secondes

15 minutes

REMARQUE : Le déplacement du fer à repasser réinitialisera le

capteur d’arrêt automatique.

REMARQUE : Dérouler complète-

ment le cordon du rembobineur,

si cette option est fournie.

18

840221004 FRv01.indd 18840221004 FRv01.indd 18 4/22/14 3:37 PM4/22/14 3:37 PM

Repassage à la vapeur

2

4

5

Régler le commutateur de

réglage de la vapeur à

(repassage à la vapeur).

Tourner le cadran de commandes

de température selon le tissu

désiré depuis le levier de

commande de vapeur. Laisser

chauffer le fer pendant 2 minutes

pour qu’il atteigne la température

désirée.

AVERTISSEMENT ! Risque

de brûlure : La tentative du

repassage à la vapeur à un

réglage de température inférieur

ou ne pas laisser le fer chauffer

pendant 2 minutes peut

occasionner un égouttement

d’eau depuis la semelle.

Régler le commutateur de

réglage de la vapeur au niveau

de vapeur désiré.

1

3

6 6

Pour un repassage à la pattemouille, tenir le fer à une distance de

15 cm (6 po) du vêtement et éviter de toucher les vêtements délicats

avec la semelle. Appuyer et relâcher le bouton de surpuissance de

vapeur pour éliminer les plis. Attendre environ 5 secondes avant

d’appuyer à nouveau sur le bouton de surpuissance de vapeur.

OU

19

840221004 FRv01.indd 19840221004 FRv01.indd 19 4/22/14 3:37 PM4/22/14 3:37 PM

Repassage à la vapeur (suite)

Régler le commutateur de

réglage de la vapeur à

(repassage à sec) pour mettre

le fer hors tension.

7 8

Tourner le cadran de commandes

de température à OFF (arrêt).

9 10

Débrancher le fer et le laisser

refroidir.

Vider l’eau du réservoir du fer

en respectant les instructions au

chapitre « Entretien et nettoyage ».

POSITION DU FER

Repos sur la semelle

Repos sur le côté

Repos sur talon

DÉTECTION DE MOUVEMENT/MISE HORS TENSION AUTOMATIQUE

Le fer se coupe automatiquement lorsqu’il est laissé dans les positions

suivantes. La durée de mise hors tension automatique varie selon la

position du fer.

TEMPS D’IMMOBILISATION

30 secondes

15 minutes

REMARQUE : Le déplacement du fer à repasser réinitialisera le

capteur d’arrêt automatique.

20

840221004 FRv01.indd 20840221004 FRv01.indd 20 4/22/14 3:37 PM4/22/14 3:37 PM

La page charge ...

Hamilton Beach 19701 Mode d'emploi

Hamilton Beach 19701 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents