Lincoln Electric K2820-1 Manuel utilisateur

Marque: Lincoln Electric

Modèle: K2820-1

Catégorie: Système de soudage

Taper: Manuel utilisateur

Ce manuel convient également à

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

OPERATOR’S MANUAL

PLASMA 20

IM10006

June, 2009

Safety Depends on You

Lincoln arc welding and cutting

equipment is designed and built

with safety in mind. However, your

overall safety can be increased by

proper installation ... and thought-

ful operation on your part. DO

NOT INSTALL, OPERATE OR

REPAIR THIS EQUIPMENT

WITHOUT READING THIS

MANUAL AND THE SAFETY

PRECAUTIONS CONTAINED

THROUGHOUT. And, most

importantly, think before you act

and be careful.

For use with machines having Code Number:

11578

PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN

AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information it is strongly recommended that you

purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box

351040, Miami, Florida 33135 or CSA Standard W117.2.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE, AND REPAIR PROCEDURES ARE

PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

CUTTING SPARKS can

cause fire or explosion.

4.a. Remove fire hazards from the plasma cut-

ting or gouging area. If this is not possible, cover

them to prevent the cutting or gouging sparks

from starting a fire. Remember that welding

sparks and hot materials from plasma cutting or gouging can

easily go through small cracks and openings to adjacent

areas. Avoid cutting or gouging near hydraulic lines. Have a

fire extinguisher readily available.

4.b. Where compressed gases are to be used at the job site, spe-

cial precautions should be used to prevent hazardous situa-

tions. Refer to “Safety in Welding and Cutting” (ANSI

Standard Z49.1) and the operating information for the equip-

ment being used.

ARC RAYS can burn.

2.a. Use safety glasses and a shield with the prop-

er filter and cover plates to protect your eyes from

sparks and the rays of the arc when performing or

observing plasma arc cutting or gouging.

Glasses,headshield and filter lens should conform

to ANSI Z87. I standards.

2.b. Use suitable clothing including gloves made from durable

flame-resistant material to protect your skin and that of your

helpers from the arc rays.

2.c. Protect other nearby personnel with suitable non-flammable

screening and/or warn them not to watch the arc nor expose

themselves to the arc rays or to hot spatter or metal.

ELECTRIC SHOCK can

kill.

1.a. The electrode and work (or ground) circuits

are electrically “hot” when the power source is on.

Do not touch these “hot” parts with your bare skin

or wet clothing. Wear dry, hole-free gloves to

insulate hands.

1.b. When the power source is operating voltages in excess of

250 volts are produced. This creates the potential for serious

electrical shock - potentially even fatal.

1.c. Insulate yourself from work and ground using dry insulation.

When cutting or gouging in damp locations, on metal frame-

work such as floors, gratings or scaffolds and when in posi-

tions such as sitting or lying, make certain the insulation is

large enough to cover your full area of physical contact with

work and ground.

1.d. Always be sure the work cable makes a good electrical con-

nection with the metal being cut or gouged. The connection

should be as close as possible to the area being cut or

gouged.

1.e. Ground the work or metal to be cut or gouged to a good elec-

trical (earth) ground.

1.f. Maintain the plasma torch, cable and work clamp in good,

safe operating condition. Replace damaged insulation.

1.g. Never dip the torch in water for cooling or plasma cut or

gouge in or under water.

1.h. When working above floor level, protect yourself from a fall

should you get a shock.

1.i. Operate the pilot arc with caution. The pilot arc is capable of

burning the operator, others or even piercing safety clothing.

1.j. Also see Items 4c and 6.

WARNING

PLASMA CUTTING or GOUGING can be hazardous.

FUMES AND GASES

can be dangerous.

3.a. Plasma cutting or gouging may produce

fumes and gases hazardous to health. Avoid

breathing these fumes and gases. When cutting

or gouging, keep your head out of the fumes.

Use enough ventilation and/or exhaust at the arc

to keep fumes and gases away from the breathing zone.

When plasma cutting or gouging on lead or cadmium

plated steel and other metals or coatings which produce

highly toxic fumes keep exposure as low as possible

and below Threshold Limit Values (TLV) using local

exhaust or mechanical ventilation. In confined spaces or

in some circumstances, outdoors, a respirator may be

required. Additional precautions are also required when

plasma cutting or gouging on galvanized steel.

3. b. The operation of plasma cutting or gouging fume control

equipment is affected by various factors including proper

use and positioning of the equipment, maintenance of the

equipment and the specific procedure and application

involved. Worker exposure level should be checked upon

installation and periodically thereafter to be certain it is with-

in applicable OSHA PEL and ACGIH TLV limits.

3.c. Do not use plasma cutting or gouging equipment in locations

near chlorinated hydrocarbon vapors coming from degreas-

ing, cleaning or spraying operations. The heat and rays of

the arc can react with solvent vapors to form phosgene, a

highly toxic gas, and other irritating products.

3.d. Gases used for plasma cutting and gouging can displace air

and cause injury or death. Always use enough ventilation,

especially in confined areas, to insure breathing air is safe.

3.e. Read and understand the manufacturer’s instructions for this

equipment and follow your employer’s safety practices.

Aug. ‘06

SAFETY

4.c. When not cutting or gouging, make certain no part of the elec-

trode circuit is touching the work or ground. Accidental contact

can cause overheating and create a fire hazard.

4.d. Do not cut or gouge tanks, drums or containers until the proper

steps have been taken to insure that such procedures will not

cause flammable or toxic vapors from substances inside. They

can cause an explosion even though they have been

“cleaned.” For information purchase “Recommended Safe

Practices for the Preparation for Welding and Cutting of

Containers and Piping That Have Held Hazardous

Substances”, AWS F4.1 from the American Welding Society

(see address above).

4.e. Vent hollow castings or containers before heating, cutting or

gouging. They may explode.

4.f. Do nor fuel engine driven equipment near area where plasma

cutting or gouging.

4.g. Sparks and spatter are thrown from the plasma arc. Wear

safety glasses, ear protection and oil free protective garments

such as leather gloves, heavy shirt, cuffless trousers, high

shoes and a cap over your hair. Wear ear plugs when cutting

or gouging out of position or in confined places. Always wear

safety glasses with side shields when in a cutting or gouging

area.

4.h. Connect the work cable to the work as close to the cutting or

gouging area as practical. Work cables connected to the build-

ing framework or other locations away from the cutting or

gouging area increase the possibility of the current passing

through lifting chains, crane cables or other alternate circuits.

This can create fire hazards or overheat lifting chains or

cables until they fail.

4.I. Read and follow NFPA 51B “ Standard for Prevention During

Welding, Cutting and Other Hot Work”, available from NFPA, 1

Batterymarch Park,PO box 9101, Quincy, Ma 022690-9101.

FOR ELECTRICALLY

powered equipment.

6.a. Turn off input power using the disconnect

switch at the fuse box before working on the

equipment.

6.b. Install equipment in accordance with the U.S. National

Electrical Code, all local codes and the manufacturer’s rec-

ommendations.

6.c. Ground the equipment in accordance with the U.S. National

Electrical Code and the manufacturer’s recommendations.

CYLINDER may explode

if damaged.

5.a. Use only compressed gas cylinders contain-

ing the correct gas for the process used and

properly operating regulators designed for the

gas and pressure used. All hoses, fittings, etc.

should be suitable for the application and maintained in good

condition.

5.b. Always keep cylinders in an upright position securely

chained to an undercarriage or fixed support.

5.c. Cylinders should be located:

• Away from areas where they may be struck or subjected to

physical damage.

• A safe distance from plasma cutting or gouging, arc weld-

ing operations and any other source of heat, sparks,

or flame.

5.d. Never allow any part of the electrode, torch or any other

electrically “hot” parts to touch a cylinder.

5.e. Keep your head and face away from the cylinder valve outlet

when opening the cylinder valve.

5.f. Valve protection caps should always be in place and hand

tight except when the cylinder is in use or connected for

use.

5.g. Read and follow the instructions on compressed gas cylin-

ders, associated equipment, and CGA publication P-l,

“Precautions for Safe Handling of Compressed Gases in

Cylinders,”available from the Compressed Gas Association

1235 Jefferson Davis Highway, Arlington, VA 22202.

Jan., 07

ELECTRIC AND MAGNETIC

FIELDS

may be dangerous

8.a. Electric current flowing through any con-

ductor causes localized Electric and Magnetic

Fields (EMF). Cutting or gouging current cre-

ates EMF fields around torch cables and cutting

machines.

8.b. EMF fields may interfere with some pacemakers, so opera-

tors having a pacemaker should consult their physician

before cutting or gouging.

8.c. Exposure to EMF fields during cutting or gouging may have

other health effects which are now not known.

8d. All operators should use the following procedures in order to

minimize exposure to EMF fields from the cutting or gouging

circuit:

8.d.1. Route thetorch andwork cablestogether - Secure

them with tape when possible.

8.d.2. Never coil the torch cable around your body.

8.d.3. Do not place your body between the torch and

work cables. Ifthe torch cableison yourrightside,

the work cable should also be on your right side.

8.d.4. Connect the work cable to the workpiece as close as

possible to the area being cut or gouged.

8.d.5. Do not work next to cutting power source.

PLASMA ARC can injure.

7.a. Keep your body away from nozzle and

plasma arc.

7.b. Operate the pilot arc with caution. The pilot arc is capable of

burning the operator, others or even piercing safety clothing.

SAFETY

NOTES

PRÉCAUTIONS DE SÛRETÉ

Pour votre propre protection lire et observer toutes les instructions

et les précautions de sûreté specifiques qui parraissent dans ce

manuel aussi bien que les précautions de sûreté générales suiv-

antes:

Sûreté Pour Soudage A L’Arc

1. Protegez-vous contre la secousse électrique:

a. Les circuits à l’électrode et à la piéce sont sous tension

quand la machine à souder est en marche. Eviter toujours

tout contact entre les parties sous tension et la peau nue

ou les vétements mouillés. Porter des gants secs et sans

trous pour isoler les mains.

b. Faire trés attention de bien s’isoler de la masse quand on

soude dans des endroits humides, ou sur un plancher

metallique ou des grilles metalliques, principalement dans

les positions assis ou couché pour lesquelles une grande

partie du corps peut être en contact avec la masse.

c. Maintenir le porte-électrode, la pince de masse, le câble

de soudage et la machine à souder en bon et sûr état

defonctionnement.

d.Ne jamais plonger le porte-électrode dans l’eau pour le

refroidir.

e. Ne jamais toucher simultanément les parties sous tension

des porte-électrodes connectés à deux machines à souder

parce que la tension entre les deux pinces peut être le

total de la tension à vide des deux machines.

f. Si on utilise la machine à souder comme une source de

courant pour soudage semi-automatique, ces precautions

pour le porte-électrode s’applicuent aussi au pistolet de

soudage.

2. Dans le cas de travail au dessus du niveau du sol, se protéger

contre les chutes dans le cas ou on recoit un choc. Ne jamais

enrouler le câble-électrode autour de n’importe quelle partie

du corps.

3. Un coup d’arc peut être plus sévère qu’un coup de soliel,

donc:

a. Utiliser un bon masque avec un verre filtrant approprié

ainsi qu’un verre blanc afin de se protéger les yeux du ray-

onnement de l’arc et des projections quand on soude ou

quand on regarde l’arc.

b. Porter des vêtements convenables afin de protéger la

peau de soudeur et des aides contre le rayonnement de

l‘arc.

c. Protéger l’autre personnel travaillant à proximité au

soudage à l’aide d’écrans appropriés et non-inflammables.

4. Des gouttes de laitier en fusion sont émises de l’arc de

soudage. Se protéger avec des vêtements de protection libres

de l’huile, tels que les gants en cuir, chemise épaisse, pan-

talons sans revers, et chaussures montantes.

5. Toujours porter des lunettes de sécurité dans la zone de

soudage. Utiliser des lunettes avec écrans lateraux dans les

zones où l’on pique le laitier.

6. Eloigner les matériaux inflammables ou les recouvrir afin de

prévenir tout risque d’incendie dû aux étincelles.

7. Quand on ne soude pas, poser la pince à une endroit isolé de

la masse. Un court-circuit accidental peut provoquer un

échauffement et un risque d’incendie.

8. S’assurer que la masse est connectée le plus prés possible

de la zone de travail qu’il est pratique de le faire. Si on place

la masse sur la charpente de la construction ou d’autres

endroits éloignés de la zone de travail, on augmente le risque

de voir passer le courant de soudage par les chaines de lev-

age, câbles de grue, ou autres circuits. Cela peut provoquer

des risques d’incendie ou d’echauffement des chaines et des

câbles jusqu’à ce qu’ils se rompent.

9. Assurer une ventilation suffisante dans la zone de soudage.

Ceci est particuliérement important pour le soudage de tôles

galvanisées plombées, ou cadmiées ou tout autre métal qui

produit des fumeés toxiques.

10. Ne pas souder en présence de vapeurs de chlore provenant

d’opérations de dégraissage, nettoyage ou pistolage. La

chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs

du solvant pour produire du phosgéne (gas fortement toxique)

ou autres produits irritants.

11. Pour obtenir de plus amples renseignements sur la sûreté,

voir le code “Code for safety in welding and cutting” CSA

Standard W 117.2-1974.

PRÉCAUTIONS DE SÛRETÉ POUR

LES MACHINES À SOUDER À

TRANSFORMATEUR ET À

REDRESSEUR

1. Relier à la terre le chassis du poste conformement au code de

l’électricité et aux recommendations du fabricant. Le dispositif

de montage ou la piece à souder doit être branché à une

bonne mise à la terre.

2. Autant que possible, I’installation et l’entretien du poste seront

effectués par un électricien qualifié.

3. Avant de faires des travaux à l’interieur de poste, la debranch-

er à l’interrupteur à la boite de fusibles.

4. Garder tous les couvercles et dispositifs de sûreté à leur

place.

Mar. ‘93

SAFETY

TThhaannkk YYoouu

for selecting a QUALITY product by Lincoln Electric. We want you

to take pride in operating this Lincoln Electric Company product

••• as much pride as we have in bringing this product to you!

Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it

handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.

The level of seriousness to be applied to each is explained below:

WARNING

This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.

This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.

CAUTION

Please Examine Carton and Equipment For Damage Immediately

When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims

for material damaged in shipment must be made by the purchaser against the transportation company at the

time the shipment is received.

Please record your equipment identification information below for future reference. This information can be

found on your machine nameplate.

Product _________________________________________________________________________________

Model Number ___________________________________________________________________________

Code Number or Date Code_________________________________________________________________

Serial Number____________________________________________________________________________

Date Purchased___________________________________________________________________________

Where Purchased_________________________________________________________________________

Whenever you request replacement parts or information on this equipment, always supply the information you

have recorded above. The code number is especially important when identifying the correct replacement parts.

On-Line Product Registration

- Register your machine with Lincoln Electric either via fax or over the Internet.

• For faxing: Complete the form on the back of the warranty statement included in the literature packet

accompanying this machine and fax the form per the instructions printed on it.

• For On-Line Registration: Go to our

WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then

“Product Registration”. Please complete the form and submit your registration.

CUSTOMER ASSISTANCE POLICY

The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-

ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln

Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-

sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-

mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,

with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or

correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any

warranty with respect to the sale of our products.

Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control

of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in

applying these types of fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com

for any updated information.

vivi

TABLE OF CONTENTS

Page

Installation.......................................................................................................................Section A

Technical Specifications.......................................................................................................A-1

Safety Precautions ...............................................................................................................A-2

Select Proper Location.........................................................................................................A-2

Stacking................................................................................................................................A-2

Tilting....................................................................................................................................A-2

High Frequency Interference Protection...............................................................................A-2

Input Electrical Connections.................................................................................................A-2

Compressed Air or Gas Input Connections..........................................................................A-3

Connections to Ground Cable..............................................................................................A-3

Torch Connections ...............................................................................................................A-3

________________________________________________________________________________

Operation.........................................................................................................................Section B

Safety Precautions ...............................................................................................................B-1

Description ...........................................................................................................................B-1

User Responsibility...............................................................................................................B-2

Design Features and Advantages........................................................................................B-2

Cutting Capability .................................................................................................................B-2

Torch Consumables ............................................................................................................B-2

Limitations ............................................................................................................................B-2

Controls and Settings...........................................................................................................B-2

Cutting Operations ...............................................................................................................B-3

Check Air Quality..................................................................................................................B-3

Cutting with a Hand Torch ............................................................................................B-3, B-4

Pilot Arc Discussion..............................................................................................................B-5

Torch Consumable Parts Selection......................................................................................B-5

________________________________________________________________________

Maintenance ....................................................................................................Section D

Safety Precautions ................................................................................................D-1

Routine Maintenance.............................................................................................D-1

Periodic Maintenance............................................................................................D-1

Compressed Air Filter............................................................................................D-2

________________________________________________________________________

Troubleshooting..............................................................................................Section E

Safety Precautions.................................................................................................E-1

How to Use Troubleshooting Guide.......................................................................E-1

Troubleshooting Guide ..........................................................................................E-2

________________________________________________________________________

Wiring Diagrams..............................................................................................Section F

Wiring Diagram......................................................................................................F-1

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

Parts Lists....................................................................................................P-607Series

________________________________________________________________________

A-1

INSTALLATION

PLASMA 20

A-1

Weight

Including

Torch Cable

21 lbs.

9.5 kg.

INPUT - SINGLE PHASE

RATED OUTPUT

OUTPUT

RECOMMEND INPUT WIRE AND FUSE SIZES

REQUIRED AIR FLOW RATE REQUIRED AIR INLET PRESSURE

PHYSICAL DIMENSIONS

TECHNICAL SPECIFICATIONS - PLASMA 20

Standard Voltage

Duty Cycle

50% on 115V (15 Amp Branch)

40% on 115V (20 Amp Branch with 20 Amp Plug*)

Current

Range

10-20 Amps

AC Input

Voltage

50/60

Hertz

115V-1Ø

Maximum

Time-Delay

Circuit Breaker

or Fuse Size

20 AMPS

15 Amps

3 Conductor, #14 AWG

Type SJT or Hard Usage

Input Cord

Depth

16 in.

406 mm

Width

6 in.

152 mm

Height

12 in.

305 mm

Open Circuit

Voltage

310 VDC

For all plasma cutting applications

Based on U.S. National Electrical Code

Ambient Temperature 30

C or Less

Pilot Current

17 Amps

AMPS

15 A

20 A

1Ø Input Current at Rated Output

115/1/50/60Hz (15 Amp Branch)

115/1/50/60Hz (20 Amp Branch with 20 Amp Plug*)

115 V: 20A @ 50%

115 V: 26A @ 40%

3.5 cu. ft./min.

(100L/min.)

72.5 to 150 PSI

( 5 Bar TO 10.3 Bar)

20 A

15 A

Output

Plug Size

5-20P*

5-15P

*5-20P plug must comply with the standard for attachment plugs and receptacles, UL498.

A-2

INSTALLATION

PLASMA 20

A-2

Read entire Installation Section before installing the

PLASMA 20.

SAFETY PRECAUTIONS

ELECTRIC SHOCK CAN KILL.

• Only qualified personnel should

perform this installation.

• Only personnel that have read and

understood the PLASMA 20

Operating Manual should install

and operate this equipment.

• Machine must be plugged into a receptacle

which is grounded per any national, local or

other applicable electrical codes.

• The PLASMA 20 power switch is to be in the OFF

(“O”) position when installing work cable and

gun and when connecting power cord to input

power.

___________________________________________

SELECT PROPER LOCATION

Place the PLASMA 20 where clean cool air can freely

circulate in and out the front, rear and side louvers.

Dirt, dust, smoke, gas or any foreign material that can

be drawn into the machine should be kept at a mini-

mum. Insure open space of at least 15 ft. around the

machine. Failure to observe these precautions can

result in excessive operating temperatures and nui-

sance shutdown of the machine.

STACKING

The PLASMA 20 cannot be stacked.

TILTING

The PLASMA 20 must be placed on a stable, level

surface so it will not topple over.

HIGH FREQUENCY INTERFERENCE

PROTECTION

The PLASMA 20 employs a touch start mechanism for

arc initiation which eliminates high frequency emis-

sions from the machine as compared with spark gap

and solid state type high frequency generators. Keep

in mind, though, that these machines may be used in

an environment where other high frequency generat-

ing machines are operating. By taking the following

steps, high frequency interference into the PLASMA

20 can be minimized.

(1) Make sure the power supply chassis is connected

to a good earth ground. The work terminal ground

does NOT ground the machine frame.

(2) Keep the work clamp isolated from other work

clamps that have high frequency.

(3) If the work clamp cannot be isolated, then keep

the clamp as far as possible from other work

clamp connections.

(4) When the machine is enclosed in a metal building,

several good earth driven electrical grounds

around the periphery of the building are recom-

mended.

Failure to observe these recommended installation

procedures may cause improper function of the PLAS-

MA 20 or possibly even damage to the control system

or power supply components.

INPUT ELECTRICAL CONNECTIONS

The PLASMA 20 must be connected to a Line-Neutral

system with protective grounding wire. Check that the

relevant electrical outlet is actually connected to the

distribution system grounding.

The PLASMA 20 is rated for 115VAC input.

Use on 15 amp branch circuits will limit cutting output.

When the output is set at 16 amps or greater, the

input fuse or circuit breaker may “blow” in roughly 30

seconds or less (depending on fuse or circuit breaker

type).

To achieve 16-20 amp output with 115VAC input,

replace the 15 amp plug on the input cord with a 20

amp plug, and connect the unit to a 20 amp branch

circuit with super lag fuses (or equivalent breaker). To

install 20 amp plug: Connect the white (neutral) wire

under terminal clamp with silver screw, and black (hot)

wire under terminal clamp with brass screw. Connect

green wire under terminal clamp with green screw.

Tighten terminal wire clamp screws securely.

5-20P plug must comply with the standard for attach-

ment plugs and receptacles, UL498. This product is

acceptable for use only when an attachment plug as

specified is properly attached to the supply cord.

• Failure to wire as instructed may cause personal

injury or damage to equipment.

• To be installed or checked by an electrician or

qualified person only.

------------------------------------------------------------------------

WARNING

A-3

INSTALLATION

PLASMA 20

A-3

Use of normal 20 amp household breakers may result

in over current trips. If breaker trips occur, reduce the

cutting current output until nuisance trips stop.

COMPRESSED AIR OR GAS INPUT

CONNECTION

A source of clean, dry air or nitrogen must be supplied

to the PLASMA 20. Oil in the air is a severe problem

and must be avoided. The supply pressure must be

between 72.5 and 150 psi (5 and 10.3 bar). The flow

rate is approximately 3.5 cu. ft./min. (100L/min.).

Failure to observe these precautions could result in

excessive operating temperatures or damage to the

torch.

Air with considerable quantity of humidity or oil

may cause an excessive wear of the parts or even

damage the torch.

If there are any doubts about the quality of the

compressed air available, it is suggested that an

air dryer be installed before the input filter

. Using

flexible airline, connect the compressed air to the

rear of the machine. Do not exceed maximum

entry pressure of 150 PSI (10.3 Bar). The pressure

must be adjusted to 72.5 PSI (5 Bar), minimum.

-----------------------------------------------------------------

•

To use the air fitting supplied with the machine apply

teflon tape to the fitting threads and install the fitting in

the port at the rear of the machine.

NOTE: When using nitrogen gas from a cylinder, the

cylinder must have a pressure regulator.

• Maximum psi from a nitrogen gas cylinder to

the PLASMA 20 regulator should never

exceed 150 psi (10.3 Bar).

• Install a hose between the nitrogen gas cylin-

der regulator and the PLASMA 20 gas inlet.

CYLINDER could explode if damaged.

• Keep cylinder upright and

chained to a fixed support.

• Keep cylinder away from areas

where it could be damaged.

• Never lift machine with cylinder attached.

• Never allow the cutting torch to touch the cylin-

der.

• Keep cylinder away from live electrical parts.

• Maximum inlet pressure 150 PSI (10.3 Bar).

__________________________________________

CONNECTION TO GROUND CABLE

Connect the work cable clamp to the piece to be cut

or to the metallic workbench. Take the following pre-

cautions:

Verify that there is a good electrical contact particular-

ly if insulated or oxidated coated sheets are cut.

Make ground connections as close as possible to the

cutting area. The use of the metallic structures which

are not part of the workpiece, such as return cable of

the cutting current, may endanger the safety system

and give poor cutting results.

Do not make a ground connection on the piece which

is to be cut off.

TORCH CONNECTION

Before starting the cutting operations verify that

the parts are properly assembled by inspecting

the head of the torch as shown in the “Operations

Section”(Torch Consumable Parts).

------------------------------------------------------------------------

Read and understand this entire section before oper-

ating the machine.

WARNING

B-1

OPERATION

PLASMA 20

B-1

SAFETY PRECAUTIONS

DESCRIPTION

The PLASMA 20 is a constant current, continuous

control plasma cutter power source.

The PLASMA 20 comes standard with an air regulator

and pressure gauge. The unit is powered from a

115Vac, 20 amp input circuit with a 40% duty cycle

rating on a 10 minute basis, with 20 amp output. The

unit includes a hand-held torch with consumables and

a work cable with clamp.

The PLASMA 20 utilizes a 3 second delay after press-

ing the trigger before arc initiation to ensure that the

operator is ready. The unit will not function if consum-

ables are not installed correctly or missing, protecting

the user. The unit uses pneumatic-action for arc initi-

ation and does not use high-frequency.

Plasma is a gas that is heated to an extremely high

temperature and ionized so that is becomes a conduc-

tor of electricity.

This cutting procedure utilizes the plasma to transfer

the electric arc to the metal workpiece. The arc melts

a small amount of the work piece and the compressed

air blows away the molten metal there by producing

the cutting action.

The torch uses compressed air from a single source,

for both the plasma, cooling and protective gas.

The start of the cycle is determined by an arc, called

the pilot arc, which is struck between the moveable

electrode (negative polarity) and the torch nozzle

(positive polarity) due to a short circuit between these

two elements.

When the torch is brought near the workpiece to be

cut and the trigger is pressed the pilot arc is trans-

ferred between the electrode and the workpiece thus

striking a plasma arc, also called the cutting arc.

The duration of the pilot arc is set in the factory at 3

seconds; if the transfer has not been made within this

time, the cycle is automatically stopped except for the

cooling air which is kept on.

ELECTRIC SHOCK

can kill.

• Do not touch electrically live parts

or electrode with skin or wet

clothing.

• Insulate yourself from work and

ground.

• Always wear dry insulating

gloves.

FUMES AND GASES

can be dangerous.

• Keep your head out of fumes.

• Use ventilation or exhaust to

remove fumes from breathing

zone.

WELDING, CUTTING and

GOUGING SPARKS

can cause fire or explosion

• Keep flammable material away.

• Do not weld, cut or gouge on contain-

ers that have held combustibles.

Observe additional Safety Guidelines detailed in

the beginning of this manual.

WARNING

ARC RAYS

can burn.

• Wear eye, ear and body

protection.

PLASMA ARC

can injure

• Keep your body away from nozzle

and plasma arc.

• Operate the pilot arc with caution. The

pilot arc is capable of burning the

operator, others or even piercing

safety clothing.

B-2

OPERATION

B-2

PLASMA 20

CONTROLS AND SETTINGS

1. ON/OFF Switch – In the ON position the machine

is ready for normal operation. All system control

circuits are activated. OFF position deactivates

control circuits.

2. Output Current Knob-Adjusts the cutting current

supplied by the machine according to the thick-

ness of material/speed.

3. Green LED – Turns ON when input voltage is

applied within normal range – blinks slowly when

input voltage goes above 130Vac, or below

95Vac.

4. Red LED – Turns ON when torch is triggered

Blinks quickly during 3 second safety pre-flow

prior to pilot arc ignition Blinks slowly if cutting arc

is not initiated after 3 second pilot arc ignition.

5. Yellow LED – Turns ON when the thermal protec-

tion is activated. Blinks slowly when the under

pressure protection is working (the pressure is

under 55 PSI, 3.8 Bar)

6. Air Regulator – Adjusts the input air pressure –

pull upward to unlock, press down to lock – nomi-

nal air pressure setting is 65 PSI, 4.5 Bar.

Note: Regulator should never be set above 87 PSI (6

Bar).

7. Compressed Air Connection

8. Input Cord

9. Work cable with clamp

10. Torch

USER RESPONSIBILITY

Variation such as plate chemistry, plate surface condi-

tion (oil, scale), plate thickness, preheat, quench,

gas type, gas flow rate and equipment may produce

results different than those expected. Some adjust-

ments to procedures may be necessary to compen-

sate for unique individual conditions. Test all proce-

dures duplicating actual field conditions.

DESIGN FEATURES AND

ADVANTAGES

• Light weight

• Continuous output control

• Indicator LEDs

• Cooling fan

• Rapid arc restrike for cutting across gaps

• 3 second arc delay for safety

•

Adjustable air pressure regulator with locking feature

•

Part-in-place verification for safety and proper operation

• Thermostatic protection with thermal indication

• Air inlet filter with water purge button to protect air

path and torch

• Lighted ON/OFF switch

• High input voltage protection

CUTTING CAPABILITY

The PLASMA 20 is rated for 20A @ 40% duty cycle.

The unit is designed to cut up to 3/8” inch mild steel,

but has the capability to cut other metals such as

stainless and aluminum (travel speed will vary).

TORCH CONSUMABLES

The torch consumables consist of an Electrode, Gas

Distributor Ring, Nozzle, and Shield Cup. The con-

sumable parts must be placed in the correct order and

secured properly for the unit to operate.

LIMITATIONS

• For indoor use only.

• Do not exceed output current and duty cycle rating

of machine. Do not use the PLASMA 20 for pipe

thawing.

• Do not power with generators or engine drives.

B-3

OPERATION

B-3

CHECKING AIR QUALITY

To check air quality, deactivate the torch (post-flow)

and place a welding filter lens in front of the torch. Any

oil or moisture in the air will be visible on the lens. DO

NOT initiate pilot arc while checking air quality.

When preparing to cut, position the machine as close

to the work as possible. Make sure you have all

materials needed to complete the job and have taken

all safety precautions. It is important to follow these

operating steps each time you use the machine.

• COMPRESSED AIR

The PLASMA 20 requires compressed air to be

attached to the unit. The input air pressure mini-

mum must be 72.5 PSI, 5 Bar and must not exceed

150 PSI, 10.3 Bar. An air regulator is included with

the unit with optimum pressure setting set to 65

PSI, 4.5 Bar.

The unit is also equipped with an air filter which cap-

tures water and oil vapor. The vapor collected can

be drained out of the bottom of the unit by turning

the drain button. The unit will not operate if the

input air pressure is below 55 PSI, 3.8 Bar.

Three Position Drain knob: (See Figure B.1)

1. Open

2. Open when no air pressure, closed when air pres-

sure.

3. Closed

CUTTING WITH A HAND TORCH

• Turn the main power and the machine power switch

on.

- The fan should start.

- The pre-charge circuit will operate for 3 seconds,

then the green "Power" LED should turn on.

• Be sure that the work lead is clamped to the work-

piece before cutting.

• Set the output current control knob at maximum

position for higher cutting speed and less dross for-

mation. Reduce the current, if desired to reduce the

kerf (cut) width, heat affected zone or travel speed

as required.

PLASMA 20

CUTTING OPERATIONS

BEFORE CUTTING

ELECTRIC SHOCK CAN KILL.

Disconnect input power by removing

the plug from the receptacle before

assembling or disassembling torch

parts, or torch and lead assemblies.

------------------------------------------------------------------------

Check and follow instructions listed in the “Safety and

Installation” section of this manual.

TORCH PARTS

Check the torch for proper assembly. Install proper

torch parts for the desired application (refer to the

Torch Consumable Parts Selection Section).

NOTE: The power supply will not operate unless the

torch shield cup is fully seated against the PIP

(Parts in Place) pins in the torch head.

INPUT POWER

Check the power source for proper input voltage.

Make sure the power source meets circuit protection

and wiring requirements.

Plug in power cord to supply input power to the unit.

GROUND CABLE

Check for a solid ground cable connection to the

workpiece.

AUTOMATIC PURGE SYSTEM

Place the ON/OFF switch to the ON position. If the

line voltage is OK, the green LED will turn on. Activate

the torch trigger to initiate air purge. There will be a 3

second delay to remove any condensation that may

have accumulated in the torch and air lines while the

system was shut down. When the air purge (Air safety

time) is complete, pilot arc will be initiated.

FIGURE B.1

WARNING

KNOB

B-4

OPERATION

B-4

NOTE: For better torch control, it is acceptable to let

the nozzle drag along the work piece surface. This

will shorten nozzle life. Also, it is acceptable to place

a non-conductive torch guide on the work piece in

order to achieve a cleaner cut

• When the trigger is released, the arc will stop.

- The gas will continue to flow for 20 seconds of

postflow. If the trigger is activated within this time

period, the pilot arc will restart after the 3 second

delay.

• If the dross is difficult to remove, reduce the cutting

speed. High speed dross is more difficult to remove

than low speed dross.

• The right side of the cut is more square than the left

as viewed along the direction of travel.

• Clean spatter and scale from the nozzle frequently.

Parts in place:

• Check the assembly of the torch consumables. If

they are not properly in place, the machine will not

start. Make sure that the shield cup is hand

tight. Do not use pliers or over tighten.

• Check the conditions of the inside of the nozzle. If

debris has collected, rub the electrode on the inside

bottom of the nozzle to remove any oxide layer that

may have built up. Refer to the “Routine

Maintenance Section".

• Check the condition of the electrode. If the end has

a crater-like appearance, replace it along with the

nozzle. The maximum wear depth of the electrode

is approximately .062”. A green and erratic arc will

indicate definite electrode failure and the electrode

should be replaced immediately.

• Replace the nozzle when the orifice exit is eroded

away or oval shaped.

ELECTRIC SHOCK CAN KILL.

Disconnect input power by removing

the plug from the receptacle before

assembling or disassembling torch

parts, or torch and lead assemblies.

------------------------------------------------------------------------

• If the machine does not reset or continues to trip,

consult the Troubleshooting Section.

• Use the proper cutting procedures referred to in

Procedure Recommendations.

PLASMA 20

• When ready to cut, place the torch near the work,

make certain all safety precautions have been taken

and pull the trigger.

- The air will flow for a preflow time of 3 seconds

and the pilot arc will start.

- The pilot arc will run for 3.0 seconds and shut off

unless the arc is brought in contact with the work

and the arc is transferred. Avoid excessive pilot

arc time by transferring the arc to the workpiece

quickly.

- When the arc is brought within 1/8” - 1/4" from

the work piece: the arc will transfer, the current

will ramp to the setting on the control panel, and

the cut can last indefinitely (or until the duty cycle

of the unit is exceeded).

• Pierce the work piece by slowly lowering the torch

onto the metal at a 30

angle away from the opera-

tor. This will blow the dross away from the torch noz-

zle. Slowly rotate the torch to vertical position as the

arc becomes deeper.

NOTE: Graphics shown are for understanding torch

angles for best results – the distances from the work

piece are exaggerated. In actual operation, the noz-

zle should be held just above the work piece surface.

• Keep moving while cutting. Cut at a steady speed

without pausing. Maintain the cutting speed so that

the arc lag is 10° to 20° behind the travel direction.

•

Use a 5° - 15° leading angle in the direction of the cut.

• Finish the cut to be made and release the trigger.

3030

VERVERTICAL ANGLETICAL ANGLE

FOR CUTTINGFOR CUTTING

CUT

TORCH AT 30

ANGLE

TO PIERCE

ROTATE TO

ANGLE TO CUT

Direction of Travel

5° - 15°

10° - 20°

Arc Lag

Leading Angle

WARNING

B-5

OPERATION

B-5

OPERATING FAULTS

During cutting operations performance faults may

arise, such as:

• Insufficient penetration:

too high cutting speed;

torch is tilted;

piece is too thick;

cutting current is too low;

torch parts are worn out;

non-genuine Manufacturer’s parts.

• Interruption of the cutting arc:

cutting speed too slow;

excessive distance between torch and work

piece;

Input Voltage too low-reduce output current;

torch parts are worn out;

non-genuine Manufacturer’s parts;

poor work cable connection/disconnected.

• Excessive slag/dross:

too low cutting speed (bottom dross);

too high cutting speed (top dross);

excessive distance between torch and work

piece;

cutting current too low;

torch parts are worn out;

non-genuine Manufacturer’s parts.

• Tilted cutting (not perpendicular):

torch position not correct;

asymmetric wear of nozzle hole and/or

incorrect assembly of the torch parts.

• Excessive wear of nozzle and electrodes:

air pressure too low;

exceeding system capability (material too

thick);

contaminated air (humidity/oil);

excessive pilot arc ignitions in the air;

improperly assembled torch;

torch nozzle contacting workpiece;

damaged or loose torch head components;

non-genuine Manufacturer’s parts.

PLASMA 20

PILOT ARC DISCUSSION

The PLASMA 20 has a smooth, continuous pilot arc. The

pilot arc is only a means of transferring the arc to the work-

piece for cutting. Repeated pilot arc starts, in rapid succes-

sion, is not recommended as these starts will generally

reduce consumable life. Occasionally, the pilot arc may

sputter or start intermittently. This is aggravated when the

consumables are worn or the air pressure is too high.

Always keep in mind that the pilot arc is designed to transfer

the arc to the workpiece and not for numerous starts without

cutting.

When the pilot arc is started, a slight impulse will be felt in

the torch handle. This occurrence is normal and is the

mechanism which starts the plasma arc. This impulse can

also be used to help troubleshoot a "no start" condition.

HEILD CUP

NOZZLE

ELECTRODE

ORCH HEAD

SSEMBLY

GAS DIFFUSER RING

FIGURE B.2

ELECTRIC SHOCK CAN KILL.

Disconnect input power by removing

the plug from the receptacle before

assembling or disassembling torch

parts, or torch and lead assemblies.

--------------------------------------------------------------------------------

WARNING

Be sure the operator is equipped with proper gloves,

clothing, eye and ear protection. Make sure no part of

the operator’s body comes in contact with the work

piece while the torch is activated.

Sparks from the cutting process can cause dam-

age to coated, painted, and other surfaces such as

glass, plastic and metal.

NOTE: Handle torch cable with care and protect

it from damage.

------------------------------------------------------------------------

TORCH CONSUMABLE PARTS

SELECTION

To change the torch consumable parts use the follow-

ing procedure:

NOTE: The nozzle, gas distributor, and electrode are

held in place by the shield cup. Position the torch with

the shield cup facing upward

to prevent these parts

from falling out when the cup is removed.

1. Unscrew and remove the shield cup from the Torch

Head Assembly. Figure B.2 Consumable Parts.

2. Remove the nozzle, gas distributor, and electrode.

3. Install the electrode, gas distributor and nozzle.

4. Hand tighten the shield cup until it is seated on the

torch head. If resistance is felt when installing the

cup, check the threads before proceeding.

CAUTION

D-1

MAINTENANCE

D-1

PLASMA 20

PERIODIC MAINTENANCE

Change consumables as required.

Torch:

• Periodically according to use, or if experiencing

cutting faults, inspect consumable parts associat-

ed with the plasma arc.

Shield Cup:

• Unscrew manually from the head of the torch.

Clean thoroughly and replace if damaged (burns,

distortions or cracks).

Nozzle:

• Check wear of plasma arc thru-hole and inner &

outer surfaces. If thru-hole is widened compared

to it’s original diameter, replace nozzle. If sur-

faces are particularly oxidized, clean them with

extra fine sand paper.

Air Distribution Ring:

• Verify there are no burns or cracks and that air-

flow holes are not obstructed. If damaged,

replace immediately.

Electrode:

• Replace electrode when crater on emitting sur-

face is about .08”(2mm).

• Before making any adjustments to the torch, let it

cool the entire post-flow time.

• Except for particular cases, it is advised to replace

electrode and nozzle AT THE SAME TIME.

• Insure correct assembly order of torch parts.

• Be careful that gas distributor ring is assembled

properly.

• Reassemble shield cup screwing it on manually

(hand tighten)

• Never assemble shield cup without having included

gas distributor ring and nozzle beforehand.

• Timely and appropriate maintenance on torch parts

is essential for safety and proper functionality of the

cutting system.

ELECTRIC SHOCK can kill.

• Have an qualified person service

this equipment.

• Disconnect input power by removing

plug from receptacle before assem-

bling or disassembling torch parts,

or torch and lead assemblies.

• Do not touch electrically hot parts.

----------------------------------------------------------------------

ROUTINE MAINTENANCE

1. Keep the cutting or gouging area and the area

around the machine clean and free of combustible

materials. No debris should be allowed to collect

which could obstruct air flow to the machine.

2. Every 3-4 months or so, the machine should be

cleaned with a low pressure airstream. Keeping the

machine clean will result in cooler operation and

higher reliability. Be sure to clean these areas:

- Printed circuit boards and heat sinks

- Power switch

• When using a low pressure airstream, wear

appropriate eye protection. Only use dry com-

pressed air for cleaning. Do not point the jet of

air at the electronic circuits.

------------------------------------------------------------------------

3. Examine the sheet metal case for dents or break-

age. Repair the case as required. Keep the case in

good condition to insure that high voltage parts are

protected and correct spacings are maintained. All

external sheet metal screws must be in place to

insure case strength and electrical ground continu-

ity.

4. Inspect the cable periodically for any slits or punc-

ture marks in the cable jacket. Replace if neces-

sary. Check to make sure that nothing is crushing

the cable and blocking the flow of air through the

air tube inside. Also, check for kinks in the cable

periodically and relieve any so as not to restrict the

flow of air to the torch.

5. Inspect Torch Body and Handle, keep thoroughly

clean WITHOUT THE USE OF SOLVENTS. In

case of damage replace components for SAFETY

CONDITIONS. If repairs cannot be made on site

contact a local field service shop.

WARNING

ELECTRIC SHOCK CAN KILL.

• Turn off machineand disconnect

input power by removing the plug

from the receptacle switch before

tightening, cleaning or replacing

consumables.

----------------------------------------------------------------------------

WARNING

CAUTION

WARNING

D-2

MAINTENANCE

D-2

PLASMA 20

COMPRESSED AIR FILTER

The unit is supplied with a filter for the compressed air

and fitted with a manual drain for condensation. (Drain

is located on the bottom of the filter). Purge periodical-

ly to remove the water in the filter by opening the drain

knob.

Do not use solvents to clean the filter; use soapy

water only.

E-1

TROUBLESHOOTING

E-1

PLASMA 20

HOW TO USE TROUBLESHOOTING GUIDE

WARNING

ELECTRIC SHOCK CAN KILL.

• Turn off machine and disconnect

input power by removing the plug

from the receptacle switch before

tightening, cleaning or replacing

consumables.

----------------------------------------------------------------------------

WARNING

This Troubleshooting Guide is provided to help you

locate and repair possible machine malfunctions.

Simply follow the three-step procedure listed below.

Step 1. LOCATE PROBLEM (SYMPTOM).

Look under the column labeled “PROBLEM (SYMP-

TOMS)”. This column describes possible symptoms

that the machine may exhibit. Find the listing that

best describes the symptom that the machine is

exhibiting.

Step 2. POSSIBLE CAUSE.

The second column labeled “POSSIBLE CAUSE” lists

the obvious external possibilities that may contribute

to the machine symptom.

Step 3. RECOMMENDED COURSE OF ACTION

This column provides a course of action for the

Possible Cause, generally it states to contact your

local Lincoln Authorized Field Service Facility.

If you do not understand or are unable to perform the

Recommended Course of Action safely, contact your

local Lincoln Authorized Field Service Facility.

Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.

Unauthorized repairs performed on this equipment may result in danger to the technician and

machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical

Shock, please observe all safety notes and precautions detailed throughout this manual.

__________________________________________________________________________

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

CAUTION

E-2

TROUBLESHOOTING

E-2

PLASMA 20

Observe all Safety Guidelines detailed throughout this manual

PROBLEMS

(SYMPTOMS)

POSSIBLE

CAUSE

RECOMMENDED

COURSE OF ACTION

GREEN LED OFF, Fan not operat-

ing. No Input Power.

GREEN LED ON, YELLOW

Overtemperature / under pressure

LED ON. Unit is overheated.

GREEN LED ON, YELLOW Over

temperature / under pressure LED

blinks. No air flow in purge or pre-

flow.

GREEN LED ON, YELLOW Over

temperature / under pressure LED

OFF, no air flow when torch switch

pressed.

GREEN LED ON, YELLOW Over

temperature / under pressure LED

OFF. Air flows, Pilot arc does not

start.

Torch has pilot arc but does not cut.

1. Plug unit into 115V outlet.

2. Reset Breaker.

1. Make sure the unit has not been

operated beyond duty cycle limits.

2. Air Flow obstructed.

1. Air not connected or pressure too

low. Check source for at least

72.5 PSI (5 Bar) during purge or

pre-flow, adjust air pressure to 65

PSI (4.5 Bar).

2. Air filter or air line blocked, torch

blocked. Replace filter cartridge.

Check that air line and torch leads

are free of twists and kinks.

1. Shield cup not properly installed

on torch. Check that shield cup is

fully seated against torch.

2. Faulty Torch Switch or Parts

Assembly in torch holder. Refer to

“Operations Section” (Torch

Consumable Parts).

3. Faulty Main PC Board Repair /

Replace Power Supply.

1. Faulty torch parts. Inspect torch

parts and replace if necessary.

2. Faulty main PC Board. Repair /

replace.

1. Work lead not connected. Make

sure work lead is connected

securely to bare metal.

2. AC input power too low. Use

shortest distance to breaker panel

possible.

3. Faulty Main PC Board.

Repair/Replace.

If all recommended possible areas of

misadjustment have been checked

and the problem persists, Contact

your local Authorized Field

Service Facility.

If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your

Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.

CAUTION

F-1

DIAGRAMS

F-1

PLASMA 20

NOTE: This diagram is for reference only. It may not be accurate for all machines covered by this manual. The specific diagram for a particular code is pasted inside

the machine on one of the enclosure panels. If the diagram is illegible, write to the Service Department for a replacement. Give the equipment code number.

INVERTER BOARD

DISPLAY BOARD

CONTROL BOARD

11/ 07

La page charge ...