Metabo HPT CJ 18DA Manuel utilisateur

Model

Modèle

Modelo

CJ 36DA

Cordless Jig Saw

Scie sauteuse sans ﬁ l

Sierra de calar a batería

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este

manual debe ser guardado en un lugar seguro.

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

2

English

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the instruction manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this instruction manual and in the sections which

contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power

tool and in this instruction manual.

Never use this power tool in a manner that has not been speciﬁ cally recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and speciﬁ cations provided with this power tool.

Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodiﬁ ed plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges

and refrigerators.

There is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the

risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

3

English

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as a dust mask, non-

skid safety shoes, hard hat or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the oﬀ -position before

connecting to power source and/or battery

pack, picking up or carrying the tool.

Carrying power tools with your ﬁ nger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part of

the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles.

A careless action can cause severe injury within a

fraction of a second.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or remove the battery pack,

if detachable, from the power tool before

making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀ ect the power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier

to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations diﬀ erent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease.

Slippery handles and grasping surfaces do not

allow for safe handling and control of the tool in

unexpected situations.

5) Battery tool use and care

a) Recharge only with the charger speciﬁ ed by

the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with speciﬁ cally

designated battery packs.

Use of any other battery packs may create a risk

of injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If

contact accidentally occurs, ﬂ ush with water.

If liquid contacts eyes, additionally seek

medical help.

Liquid ejected from the battery may cause

irritation or burns.

e) Do not use a battery pack or tool that is

damaged or modiﬁ ed.

Damaged or modiﬁ ed batteries may exhibit

unpredictable behaviour resulting in ﬁ re,

explosion or risk of injury.

4

English

f) Do not expose a battery pack or tool to ﬁ re or

excessive temperature.

Exposure to ﬁ re or temperature above 265 °F may

cause explosion.

g) Follow all charging instructions and do

not charge the battery pack or tool outside

the temperature range speciﬁ ed in the

instructions.

Charging improperly or at temperatures outside

the speciﬁ ed range may damage the battery and

increase the risk of ﬁ re.

6) Service

a) Have your power tool serviced by a

qualiﬁ ed repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is

maintained.

b) Never service damaged battery packs.

Service of battery packs should only be

performed by the manufacturer or authorized

service providers.

– WARNING –

To reduce the risk of injury, user must read

instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live” and could

give the operator an electric shock.

2. Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body leaves

it unstable and may lead to loss of control.

3. ALWAYS wear ear protectors when using the tool

for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

4. NEVER touch moving parts.

NEVER place your hands, ﬁ ngers or

other body parts near the tool’s moving

parts.

5. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

6. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree

limbs or logs.

7. NEVER use a power tool for applications other

than those speciﬁ ed.

NEVER use a power tool for applications other than

those speciﬁ ed in the Instruction Manual.

8. Handle tool correctly.

Operate the tool according to the instructions

provided herein. Do not drop or throw the tool.

NEVER allow the tool to be operated by children,

individuals unfamiliar with its operation or

unauthorized personnel.

9. Keep all screws, bolts and covers tightly in

place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

10. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

11. Blades and accessories must be securely

mounted to the tool.

Prevent potential injuries to yourself or others.

Blades, cutting implements and accessories which

have been mounted to the tool should be secure and

tight.

12. Handle the blades very carefully.

13. Check the blade carefully for cracks or damage

before operation. Replace cracked or damaged

bit immediately.

14. Avoid cutting nails. Inspect for and remove all

nails from the workpiece before operation.

15. Hold the tool ﬁ rmly.

16. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂ ow at all times. Check for dust build-up

frequently.

17. NEVER use a tool which is defective or operating

abnormally.

If the tool appears to be operating unusually, making

strange noises, or otherwise appears defective, stop

using it immediately and arrange for repairs by a

metabo HPT authorized service center.

18. NEVER leave tool running unattended. Turn

power oﬀ .

Don’t leave tool until it comes to a complete stop.

19. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

5

English

20. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

21. ALWAYS wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

22. ALWAYS wear a mask or respirator to protect

yourself from dust or potentially harmful particles

generated during operation.

23. ALWAYS ﬁ rmly grip the handle while operating.

24. ALWAYS be careful with buried object such as an

underground wiring.

Touching these active wiring or electric cable with

this tool, you may receive an electric shock.

Conﬁ rm if there are any buried object such as electric

cable within the wall, ﬂ oor or ceiling where you are

going to operate here after.

25. Deﬁ nitions for symbols used on this tool

V ................ volts

—

---

............. direct current

Hz .............. hertz

A ................ amperes

no .............. no load speed

---/min ........ revolutions or reciprocation per minute

26. Do not touch the blade immediately after

operation: it may be extremely hot and could

burn your skin.

27. During use, do not touch the metal portion of the tool.

28. NEVER touch the blade with bare hands after

operation.

29. Because the cordless jig saw operates by battery

power, be aware of the fact that it can begin to

operate at any time.

30. When working at elevated locations, clear the area of

other people and aware of conditions below you.

31. Do not use the product if the tool or the battery

terminals (battery mount) are deformed.

Installing the battery could cause a short circuit that

could result in smoke emission or ignition.

32. Keep the tool’s terminals (battery mount) free of swarf

and dust.

○

Prior to use, make sure that swarf and dust have not

collected in the area of the terminals.

○

During use, try to avoid swarf or dust on the tool from

falling on the battery.

○

When suspending operation or after use, do not leave

the tool in an area where it may be exposed to falling

swarf or dust.

Doing so could cause a short circuit that could result

in smoke emission or ignition.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers.

To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating

instructions for battery charger Model UC18YSL3.

2. Before using battery charger, read all instructions

and cautionary markings on (1) battery charger, (2)

battery, and (3) product using battery.

3. To reduce risk of injury, charge metabo HPT

rechargeable battery multi volt type series and BSL18

series. Other type of batteries may burst causing

personal injury and damage.

4. Use of an attachment not recommended or sold by

the battery charger manufacturer may result in a risk

of ﬁ re, electric shock, or injury to persons.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in good

electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

6

English

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or

greater than

but less

than

Length of Cord, Feet (Meter)

25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

1,250 watts

= 10 amperes

125 volts

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger; take it to a

qualiﬁ ed serviceman when service or repair is

required. Incorrect reassembly may result in a risk of

electric shock or ﬁ re.

11. To reduce risk of electric shock, unplug charger from

receptacle before attempting any maintenance or

cleaning. Removing the battery will not reduce this

risk.

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER

You must charge the battery before you can use the power

tool. Before using the model UC18YSL3 battery charger,

be sure to read all instructions and cautionary statements

on it, the battery and in this manual.

REMEMBER: USE ONLY metabo HPT BATTERY TYPE

MULTI VOLT SERIES. OTHER TYPES OF BATTERIES

MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:

Improper use of the battery

or battery charger can lead to

serious injury. To avoid these

injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged

or is completely worn out. The battery can explode in

a ﬁ re.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s

air vents. Electric shock or damage to the battery

charger may result.

5. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

6. NEVER charge when the temperature is below 14°F

(-10°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the

battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use DC power to charge.

11. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C) such as inside metal box or car.

12. NEVER expose the battery or battery charger to rain

or wet conditions.

13. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

14. ALWAYS wait at least 15 minutes between charges to

avoid overheating the charger.

15. ALWAYS disconnect the power cord from its

receptacle when the charger is not in use.

7

English

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.

○

During work make sure that swarf and dust do not fall

on the battery.

○

Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.

○

Do not store an unused battery in a location exposed

to swarf and dust.

○

Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from ﬁ re immediately when leakage or

foul odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears

abnormal during use, recharging or storage,

immediately remove it from the equipment or battery

charger, and stop use.

12. Do not immerse the battery or allow any ﬂ uids to ﬂ ow

inside. Conductive liquid ingress, such as water,

can cause damage resulting in ﬁ re or explosion.

Store your battery in a cool, dry place, away from

combustible and ﬂ ammable items. Corrosive gas

atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with

clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you ﬁ nd rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it to

your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of ﬁ re. Please observe the

following matters when storing the battery.

○

Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.

○

Either install the battery in the power tool or

store by securely pressing into the battery

cover until the ventilation holes are concealed to

prevent short-circuits (See Fig. 3).

8

English

REGARDING LITHIUM-ION BATTERY

TRANSPORTATION

When transporting a lithium-ion battery, please observe

the following precautions.

WARNING

Notify the transporting company that a package

contains a lithium-ion battery, inform the company

of its power output and follow the instructions of the

transportation company when arranging transport.

●

Lithium-ion batteries that exceed a power output

of 100 Wh are considered to be in the freight

classiﬁ cation of Dangerous Goods and will

require special application procedures.

●

For transportation abroad, you must comply with

international law and the rules and regulations

of the destination country.

●

If the BSL36B18 is installed in the power tool, the

power output will exceed 100 Wh and the unit

will be classiﬁ ed as Dangerous Goods for freight

classiﬁ cation.

Wh

Power Output

2 to 3 digit number

Fig. 1

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

USB DEVICE CONNECTION

PRECAUTIONS

When an unexpected problem occurs, the data in a USB

device connected to this product may be corrupted or lost.

Always make sure to back up any data contained in the

USB device prior to use with this product.

Please be aware that our company accepts absolutely no

responsibility for any data stored in a USB device that is

corrupted or lost, nor for any damage that may occur to a

connected device.

9

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have ﬁ rst read and understood all safey

instructions contained in this manual.

Some illustrations in this instruction manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Jig Saw (CJ36DA)

Guide

roller

Change knob

Base plate

Base

Hexagonal bar wrench

Motor

Battery

Name plate

Handle

Switch

Stopper

Lock-oﬀ button

Dial

LED light

Lever

Blade

Fig. 2

2. Battery

(optional accessories…sold separately)

3. Battery Charger

(optional accessories…sold separately)

Battery

Latch

Ventilation holes

Terminals

Battery cover

Nameplate

Cord

Guide rail

Charge indicator lamp

Ventilation holes

Body

Fig. 3

Fig. 4

10

English

SPECIFICATIONS

1. Cordless Jig Saw

Model CJ36DA

Motor DC brushless motor

Capacity

Wood 6 – 19/64" (160 mm)

Mild steel 25/64" (10 mm)

Stainless steel 1/8" (3.2 mm)

No-load speed 800 – 3,500 /min

Stroke 1 – 1/32" (26 mm)

Min. cutting radius 1" (25 mm)

Cutting Angle Range 0 – 45°

Battery*

Type* Li-ion battery Model BSL36B18

Voltage DC 36 V / 18V

Weight 6.6 lbs. (3.0 kg) (BSL36B18 attached)

* Existing batteries (BSL3660/3626/3620, BSL18xx and BSL14xx series, etc.) cannot be used with this tool.

2. Battery Charger

Model UC18YSL3

Input power source Single phase: AC 120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C))

BSL36B18: Approx. 52 min

Charging voltage DC 14.4 – 18 V

Charging current DC 8.0 A

Weight 1.3 lbs. (0.6 kg)

NOTE: The charging time may vary according to temperature and power source voltage.

11

English

ASSEMBLY AND OPERATION

APPLICATIONS

○

Cutting various lumber and pocket cutting

○

Cutting mild steel plate, aluminum plate, and copper

plate

○

Cutting plastics, such as phenol resin and vinyl

chloride

○

Cutting thin and soft construction materials

○

Cutting stainless steel plate (With No. 97 blade)

REMOVAL AND INSTALLATION METHOD

OF BATTERY

○

How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click. If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 5).

○

How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 5).

Latch

Battery

Pull out

Insert

Push

Handle

Fig. 5

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.

○

The power source voltage is stated on the nameplate.

○

The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on

the nameplate, the charger will burn out.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charge

indicator lamp will blink in red. (At 1-second intervals)

WARNING

Do not use the electrical cord

if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Firmly Insert the battery into the battery charger as

shown in Fig. 6.

Charge indicator lamp

Guide rail

Battery

Fig. 6

12

English

3. Charging

When inserting a battery in the charger, the charge

indicator lamp will blink in blue.

When the battery becomes fully recharged, the

charge indicator lamp will light up in green. (See

Table 2)

(1) Charge indicator lamp indication

The indications of the charge indicator lamp will be

as shown in Table 2, according to the condition of the

battery charger or the battery.

Table 2

Indications of the charge indicator lamp

Charge

indicator

lamp

(RED /

BLUE /

GREEN /

PURPLE)

Before

charging

Blinks

(RED)

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Plugged into power source

While

charging

Blinks

(BLUE)

Lights for 0.5 seconds. Does not light

for 1 second. (oﬀ for 1 second)

Battery capacity at less than

50%

Blinks

(BLUE)

Lights for 1 second. Does not light for

0.5 seconds. (oﬀ for 0.5 seconds)

Battery capacity at less than

80%

Lights

(BLUE)

Lights continuously

Battery capacity at more than

80%

Charging

complete

Lights

(GREEN)

Lights continuously

(Continuous buzzer sound: about

6 seconds)

Overheat

standby

Blinks

(RED)

Lights for 0.3 seconds. Does not light

for 0.3 seconds. (oﬀ for 0.3 seconds)

Battery overheated. Unable

to charge. (Charging will

commence when battery cools)

Charging

impossible

Flickers

(PURPLE)

Lights for 0.1 seconds. Does not light

for 0.1 seconds. (oﬀ for 0.1 seconds)

(Intermittent buzzer sound: about

2 seconds)

Malfunction in the battery or the

charger

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are

as shown in the Table 3, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 3

Rechargeable

batteries

Temperatures at which the battery

can be recharged

BSL36B18

32°F – 122°F

(0°C – 50°C)

(3) Regarding recharging time (At 68°F (20°C))

Table 4 Charging time

Charger

Battery

UC18YSL3

BSL36B18 Approx. 52 min.

NOTE

The recharging time may vary according to the

ambient temperature.

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing from

receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

NOTE

Be sure to pull out the battery from the battery

charger after use, and then keep it.

13

English

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the ﬁ rst and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

CAUTION

●

When the battery charger has been continuosly

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated

because it has been left for a long time in a

location subject to direct sunlight or because the

battery has just been used, the charge indicator

lamp of the charger lights for 0.3 seconds, does

not light for 0.3 seconds (oﬀ for 0.3 seconds). In

such a case, ﬁ rst let the battery cool, then start

charging.

●

When the charge indicator lamp ﬂ ickers (at

0.2–second intervals), check for and take out

any foreign objects in the charger’s battery

installation hole. If there are no foreign objects,

it is probable that the battery or charger is

malfunctioning. Take it to your authorized

Service Center.

HOW TO RECHARGE USB DEVICE

WARNING

○

Prior to use, check the connecting USB cable for

any defect or damage.

Using a defective or damaged USB cable can

cause smoke emission or ignition.

○

When the product is not being used, cover the

USB port with the rubber cover.

Buildup of dust etc. in the USB port can cause

smoke emission or ignition.

NOTE

○

The time required for charging will be longer when

a USB device and battery are being simultaneously

charged.

○

There may be an occasional pause during USB

recharging.

○

When a USB device is not being charged, turn the

USB power switch OFF and remove the USB device

from the charger.

Failure to do so may not only reduce the battery life

of a USB device, but may also result in unexpected

accidents.

(1) Select a charging method

Depending on the charge method selected, either the

battery is inserted into the charger or the power cord

is plugged into an outlet.

○

Charging a USB device by battery (Fig. 7-a)

○

Charging a USB device from a electrical outlet

(Fig. 7-b)

○

Charging a USB device and battery from a

electrical outlet (Fig. 7-c)

abc

Fig. 7

(2) Turn the USB power switch ON (Fig. 8)

When you turn the USB power switch ON, the USB

power indicator lamp will light up.

USB power

indicator lamp

Rubber cover

USB port

USB cable

USB power

switch

Fig. 8

(3) Connect the USB cable. (Fig. 8)

Pull back the rubber cover and ﬁ rmly plug in a

commercially available USB cable (appropriate to the

device being charged) into the USB port.

14

English

○

When the power cord is not plugged into an outlet

and the battery runs out of power, power output will

stop and the USB power indicator lamp will shut oﬀ .

○

When the USB power indicator lamp goes out,

change the battery or plug the power cord into an

electrical outlet.

(4) When charging is completed

○

The USB power indicator lamp will not go out when a

USB device has been completely charged.

To verify charge status, check the USB device.

○

Turn the USB power switch OFF and unplug the

power cord from the electrical outlet. (Fig. 8)

○

Remove the battery from the charger and place the

rubber cover over the USB port.

PRIOR TO OPERATION

CAUTION

To avoid serious accident, ensure the switch is

in the OFF position, and pull out the battery.

1. Check the work area environment

Check the work area to make sure that it is clear of

debris and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

2. Power switch

Ensure that the switch is in the OFF position.

3. Dust produced in operation

The dust produced in normal operation may aﬀ ect

the operator’s health. Either of following way is

recommended.

a) Wear a dust mask

b) Use external dust collection equipment

When using the external dust collection equipment,

connect the adapter with the hose from external dust

collection equipment. (Fig. 9)

Base

Rear hole

Dust collection

adapter

Adapter

Nose

Cleaner

HookNotch

Fig. 9

4. Changing blades

CAUTION

●

Be sure to switch power OFF and disconnect the

battery from the body when changing blades.

●

Do not touch the lever when plunger is moving.

●

Never touch the blade immediately after use.

The metal is hot and can easily burn your skin.

(1) Pull the lever in the direction indicated by the arrow.

(Fig. 10-І)

(2) With the lever pulled, insert the blade until it butts

against the outlet of the blade holder tip. (Fig. 10-ІІ)

(3) Release the lever. (Fig. 10-ІІІ)

Plunger

Blade

holder

Blade holder

Blade

Guide roller

Fig. 10-І

Lever

Fig. 10-ІІ Fig. 10-ІІІ

Fig. 10

15

English

NOTE

○

Conﬁ rm the protrusions of blade inserted to the blade

holder surely.

○

Conﬁ rm the blade located between the groove of

roller. (Fig. 11)

Blade

Roller

Fig. 11

5. Adjusting the blade operating speed

The jig saw is equipped with the electric control

circuit which enables stepless speed control. To

adjust the speed, turn the dial shown in Fig. 12.

When the dial is set to “1”, the jig saw operates at

the minimum speed (800 /min). When the dial set

to “5”, the jig saw operates at the maximum speed

(3,500 /min). Adjust the speed according to the

material to be cut and working eﬃ ciency.

Blade operating speed

Mode Dial Blade operating speed

Standard Mode 1 – 5 800 – 3,500 /min

AUTO Mode A

No load: 1,400 /min

With load: 3,500 /min

With AUTO Mode, the vibration frequency may not reach 3,500 /min depending on variables such as the type of

work.

No-load speed

3,500 /min

1,400 /min

800 /min

Dial

Fig.12

The tool is equipped with two modes: “Standard

Mode” and “AUTO Mode”.

(1) Standard Mode

You can change the blade operating speed between

800 to 3,500 /min by adjusting the dial from “1” to “5”.

(2) AUTO Mode

AUTO Mode automatically selects a speed between

1,400 and 3,500 /min to suit the operating load and

maintains that speed until the switch is turned oﬀ .

This has the eﬀ ect of lowering vibration and noise

prior to and during operation.

Adjust the dial for the mode and speed that best suits your

task conditions and materials.

CAUTION

At low speed (dial setting: 1 or 2) do not cut a

wood with a thickness of more than 5/16" (8 mm)

or metal with a thickness of more than 1/32"

(1 mm).

6. Adjusting the orbital operation

(1) This Jig Saw employs orbital operation which moves

the blade back and forth, as well as up and down. Set

the change knob shown in Fig. 13 to “0” to eliminate

the orbital operation (the blade moves only up and

down). The orbital operation can be selected in 4

steps from “0” to “III”.

Change knob

Fig. 13

(2) For the hard material, such as a steel plate, etc.,

decrease the orbital operation. For the soft material,

such as lumber, plastic, etc., increase the orbital

operation to increase work eﬃ ciency. To cut the

material accurately, decrease the orbital operation.

16

English

7. Cutting stainless steel plates

This Jig Saw can cut stainless steel plates by using

No. 97 blade (sold separately). Carefully read

“Concerning cutting of stainless steel plates” for

proper operation.

8. Splinter guard

CAUTION

Be sure to switch OFF and disconnect the

battery from body.

Using the splinter guard when cutting wood materials

will reduce splintering of cut surfaces.

Using the provided Allen wrench, tighten the bolts in

the lower area of the base, moving the base as far

forward as possible. (See Fig. 14)

Base

Allen wrench

Base bolt

Fig. 14

Insert the splinter guard in the space on the base, and

push it completely. (see Fig. 15)

Splinter

guard

Base

Fig. 15

9. Sub base (sold separately)

CAUTION

Be sure to switch OFF and disconnect the

battery from body.

Used for curved cutting of pieces such as arcs and

circles. Makes the task easier by eliminating any

snags that may occur between the rear of the base

and the material.

Fit into position after hooking the sub base to the tip

of the base. (Fig. 16)

To detach, pull up.

Base

Sub base

Fig. 16

NOTE

When the sub base is attached, the blade’s protrusion

from the material being cut will be reduced by 3mm.

When the blade has been moved down to the lowest

point, check to make sure that it is protruding from the

material.

10. Attaching and detaching the chip cover (Fig. 17)

Chip cover’s catches

Guide section

Slots

Chip

cover

Fig.17

WARNING

To prevent accidents when attaching or detaching

the chip cover, make sure the unit is switched oﬀ

and pull out the battery.

NOTE

The chip cover cannot be attached with the base in

an inclined state.

(1) Position the unit at a right angle to the surface

(0-degree incline).

(2) Holding the chip cover’s guide section open by hand,

push into the main unit.

Blade

17

English

(3) Insert the chip cover’s catches into the main unit’s

slots.

(4) When detaching, spread the catches of the chip

cover and draw them out from the main unit’s slots.

11. Prepare a work bench (Fig. 18)

Since the blade will extend beyond the lower surface

of the material, place the material on a work bench

when cutting. If a square block is utilized as a work

bench, select level ground to ensure it is properly

stabilized. An unstable work bench will result in

hazardous operation.

Base

Lumber

Work bench

Blade

Fig. 18

CAUTION

To avoid possible accident, always ensure that

the portion of material remaining after cutting is

securely anchored or held in position.

12. Check battery insertion

WARNING

If the battery is inserted while the power switch

is in the ON position, the power tool will start

operating immediately, inviting serious accident.

CAUTION

Until the battery locks in place with a little click,

if not, it may accidentally fall out of the tool

causing injury to you or someone around you.

OPERATION

WARNING

●

Never touch the moving parts.

●

Never operate the Jig saw with the blade turned

upward or to the side.

●

Be sure to turn oﬀ the switch, push the lock-

oﬀ button to the lock position, then remove the

battery from the tool in the following situations:

•

When stopping or ending work

•

When attaching or removing a blade

•

When attaching or removing accessories or

optional parts

• When adjusting the base position

• When maintaining, inspecting, or storing the

tool

CAUTION

●

To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.

●

Don’t remove jig saw from workpiece during a

cut while the blade is moving.

●

Pull out the battery after completing operation.

●

In order to prevent blade dislodging, damage

or excessive wear on the Plunger, please make

sure to have surface of the base plate attached

to the work piece while sawing.

●

At low speed do not cut a wood with a thickness

of more than 3/8" (10 mm) or metal with a

thickness of more than 1/32" (1 mm).

NOTE

Take care not to lock the motor. If the motor is locked,

immediately turn the power oﬀ . If the motor is locked

for a while, the motor or battery may be burnt.

1. Switch operation

(1) Lock-oﬀ button

The tool is equipped with a lock-oﬀ button. To start

the tool, press the lock-oﬀ button and then squeeze

the trigger switch. (Fig. 19)

Lock-oﬀ button

Push

Lock

Unlock

Switch

Fig. 19

18

English

CAUTION

Do not ﬁ x and secure the lock-oﬀ button.

Besides, keep your ﬁ nger oﬀ the trigger switch

when the tool is being carried around. Otherwise,

the trigger switch can be inadvertently turned

ON, resulting in unexpected accidents.

(2) Trigger switch

This tool is equipped with a variable speed controlled

trigger switch. The tool can be turned “ON” or

“OFF” by squeezing or releasing the trigger. The

blade plunger stroke rate can be adjusted from the

minimum to maximum nameplate stroke rate by

the pressure you apply to the trigger. Apply more

pressure to increase the speed and release pressure

to decrease speed.

In addition, releasing the switch activates a break that

stops the blade immediately.

Switch

Fig. 20

For continuous operation, pull the switch in all the

way and press the stopper.

To cancel continuous operation, once again pull the

switch in all the way until the stopper is freed, and

then release the switch.

Stopper

Fig. 21

2. How to use the LED light (Fig. 22)

The LED light will light the area at the tip of the tool

when the switch is drawn.

The LED light will automatically power oﬀ 10 seconds

after the switch is released.

LED light

Lock oﬀ button

Switch

Fig. 22

CAUTION

Do not look directly into the light from the LED

lamp. Continuous and direct exposure to the

light from the LED lamp can injure your eyes.

3. LED light warning signals (Fig. 23)

This product features functions that are designed

to protect the tool itself as well as the battery. While

the switch is pulled, if any of the safeguard functions

activate during operation, the LED light will blink as

described in Table 5. When any of the safeguard

functions are triggered, immediately remove your

ﬁ nger from the switch and follow the instructions

described under corrective action.

Fig. 23

Table 5

Safeguard Function LED Light Display Corrective Action

Overload Protection

On 0.1 second/oﬀ 0.1 second

Remove the cause of the overloading.

Temperature Protection

On 0.5 second/oﬀ 0.5 second

Allow the tool and battery to thoroughly

cool.

19

English

4. About remaining battery indicator

You can check the battery’s remaining capacity by

pressing the remaining battery indicator switch to

light the indicator lamp. (Fig. 24, Table 6)

The indicator will shut oﬀ approximately 3 seconds

after the remaining battery indicator switch is

pressed.

It is best to use the remaining battery indicator as

a guide since there are slight diﬀ erences such as

ambient temperature and the condition of the battery.

Also, the remaining battery indicator may vary from

those equipped to a tool or charger.

Display panel

Remaining battery

indicator lamp

Remaining battery

indicator switch

Fig. 24

Table 6

State of lamp Battery Remaining Power

Lights ;

The battery remaining power is over

75%.

Lights ;

The battery remaining power is

50% – 75%.

Lights ;

The battery remaining power is

25% – 50%.

Lights ;

The battery remaining power is less

than 25%.

Blinks ;

The battery remaining power is

nearly empty. Recharge the battery

soonest possible

Blinks ;

Output suspended due to high

temperature. Remove the battery

from the tool and allow it to fully cool

down.

Blinks ;

Output suspended due to failure or

malfunction. The problem may be

the battery so please contact your

dealer.

As the remaining battery indicator shows somewhat

diﬀ erently depending on ambient temperature and battery

characteristics, read it as a reference.

NOTE

Do not give a strong shock to the display panel or

break it. It may lead to a trouble.

20

English

CUTTING

CAUTION

In order to prevent blade dislodging, damage

or excessive wear on the plunger, please make

sure to have surface of the base plate attached

to the work piece while sawing.

1. Rectilinear cutting

When cutting on a straight line, ﬁ rst draw a marking

gauge line and advance the saw along that line.

Using the guide (sold separately) will make it possible

to cut accurately on a straight line.

(1) Loosen the base bolt allen wrench attached on base.

(Fig. 25)

Allen wrench

Base

Base bolt

Fig. 25

(2) Move the base fully forward, and tighten the base bolt

again. (Fig. 25)

(3) Attach the guide by passing it through the attachment

hole on the base and tighten the M5 bolt. (Fig. 26)

M5 bolt

Attachment hole

Guide

Fig. 26

(4) Set the orbital position to “0”.

NOTE

To ensure accurate cutting when using the Guide

(Fig. 27), always set the orbital position to “0”.

Guide

Change knob

Fig. 27

2. Sawing curved lines

When sawing a small circular arc, reduce the feeding

speed of the machine. If the machine is fed too fast, it

could cause the blade to break.

Set the orbital position to “0”.

3. Cutting a circle or a circular arc

The guide also will be helpful for circular cutting.

After attaching the guide by same way noted as

above, drive the nail or screw into the material

through the hole on the guide, then use it for a axis

when cutting. (Fig. 28)

Set the orbital position to “0”.

Wood screw

or nail

Guide hole

Guide

Change knob

Sub base

Fig. 28

La page charge ...

Metabo HPT CJ 18DA Manuel utilisateur

Ce manuel convient également à

Metabo HPT CJ 18DA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents