GE UCC15NJII Guide d'installation

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

Find these numbers on a label

on the top inner case liner of the

unit toward the front.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

AND INSTALLATION

INSTRUCTIONS

ICE MACHINE

49-60745 Rev. 4 02-19 GEA

UCC15

ENGLISH/FRANÇAIS/

ESPAÑOL

SAFETY INFORMATION .........3

USING THE ICE MACHINE

Packaging ............................5

Controls ..............................5

Features ..............................6

Starting the Ice Machine ................6

INSTALLATION INSTRUCTIONS

Grounding the Ice Machine ..............7

Before You Begin ......................7

Location and Preparation ...............7

Advance Planning .....................9

Dimensions ..........................10

Door Swing .......................... 11

Door Panel ...........................12

Handle Reversing Instructions ..........14

Plumbing ............................14

Placement of the Ice Machine ..........15

CARE AND CLEANING ..........16

TROUBLESHOOTING TIPS ......18

LIMITED WARRANTY ...........19

ACCESSORIES .................. 20

CONSUMER SUPPORT ..........22

249-60745 Rev. 4

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-60745 Rev. 4 3

CAUTION To reduce the risk of injury when using your appliance, follow these basic safety

precautions.

■ Keepfingersoutofthe“pinchpoint”areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.

■ Avoidcontactwiththemovingpartsoftheejector

mechanism, or with the heating element that

releases the cubes. Do not place fingers or hands on

the automatic ice making mechanism while the ice

machine is plugged in.

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

WARNING To reduce the risk of fire, explosion, electric shock, or injury when using your ice

machine follow these basic safety precautions:

■ Thisicemachinemustbeproperlyinstalled

and located in accordance with the Installation

Instructions before it is used.

■ Unplugtheappliancebeforemakingrepairs,

replacing a light bulb, or cleaning.

NOTE: Power to the appliance cannot be

disconnected by any setting on the control panel.

NOTE: Repairs must be performed by a qualified

service professional.

■ Replaceallpartsandpanelsbeforeoperating.

■ Donotstoreorusegasolineorotherflammable

vapors and liquids in the vicinity of this or any other

appliance.

■ Becauseofpotentialsafetyhazardsundercertain

conditions, we strongly recommend against the use

of an extension cord. However, if you must use an

extension cord, it is absolutely necessary that it be a

UL-listed(intheUnitedStates)oraCSAcertified(in

Canada),3-wiregroundingtypeapplianceextension

cord having a grounding type plug and outlet and

that the electrical rating of the cord be 15 amperes

(minimum)and120volts.

■ Topreventsuffocationandentrapmenthazardsto

children, remove the door from any appliance before

disposing of it or discontinuing its use.

■ Donotallowchildrentoclimb,standorhangonthe

door handle of the appliance. They could seriously

injure themselves.

■ Icemachinescaleremovercontainsacids.Acids

can cause burns. If concentrated cleaner comes in

contact with skin, flush with water. If swallowed, do

NOT induce vomiting. Give large amounts of water

ormilk.CallPhysicianimmediately.Keepoutofthe

reach of children.

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

INSTALLATION

WARNING EXPLOSION HAZARD

Keepflammablematerialsandvapors,suchasgasoline,awayfromappliance.Failuretodosocanresultinfire,

explosion, or death.

449-60745 Rev. 4

WARNING SUFFOCATION AND CHILD ENTRAPMENT HAZARD

Removethedoorfromtheappliancepriortodisposal.Failuretodosocanresultinchildentrapmentwhichcan

lead to death or brain damage.

IMPORTANT: Child entrapment and suffocation are not

problems of the past. Junked or abandoned appliances

arestilldangerouseveniftheywillsitfor“justafew

days.”Ifyouaregettingridofyouroldappliance,

please follow the instructions below to help prevent

accidents.

Before You Throw Away Your Old Appliance:

■ Take off the doors.

■ Leavetheinternalcomponentsinplacesothat

children may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which

under federal law must be removed prior to product

disposal. If you are getting rid of an old refrigeration

product, check with the company handling the disposal

about what to do.

PROPER DISPOSAL OF YOUR OLD APPLIANCE

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a

3-prong(grounding)plugwhichmateswithastandard

3-prong(grounding)walloutlettominimizethe

possibilityofelectricshockhazardfromthisappliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

The ice maker should always be plugged into its own

115volt,60Hz,15ampcircuit.Thisprovidesthebest

performance and also prevents overloading house

wiringcircuitswhichcouldcauseafirehazardfrom

overheated wires.

Never unplug your ice maker by pulling on the power

cord. Always grip plug firmly and pull straight out from

the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the ice maker, be careful not to roll over

or damage the power cord.

KEEP FROM FREEZING: Severe damage will occur

to the unit if left in or operated in temperatures beyond

the limits listed in this manual. That damage is NOT

covered by warranty.

KEEP DRY: Do not locate in low lying areas where

puddles will accumulate

PROVIDE SHADE: Heat gain from the sun will reduce

the unit's ability to make and store ice, and ultraviolet

radiation from the sun can potentially damage the unit's

plastic components.

WATER SUPPLY: Avoid a long run of hose or tubing

exposed to the sun. Plastic water supply tubing should

beratedforpotablewaterandincludeUVprotection.

Copper tubing is recommended.

BACK FLOW PREVENTION: The unit includes back

flow prevention, no additional check valve is required.

DRAINAGE: DO NOT drain into swimming pool or onto

grounds.

CONNECTING ELECTRICITY

OUTDOOR USE NOTICE

WARNING ELECTRICAL SHOCK HAZARD

Plug into a grounded 3-prong outlet

Do not remove the ground prong

Do not use an adapter

Failuretofollowtheseinstructionscanresultindeath,fire,orelectricalshock.

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

READ AND SAVE THESE INSTRUCTIONS

49-60745 Rev. 4 5

Remove Packaging

IMPORTANT: Do not remove any permanent instruction

labels inside your ice machine or the Tech Sheet that is

fastened behind the lower access panel.

■Removetapeandanylabelsfromyouricemaker

beforeusing(exceptthemodelandserialnumber

label).

To remove any remaining tape or glue, rub the area

briskly with your thumb. Tape or glue residue can also

be easily removed by rubbing a small amount of liquid

dish soap over the adhesive with your fingers. Wipe

with warm water and dry.

■Donotusesharpinstruments,rubbingalcohol,

flammable fluids or abrasive cleaners to remove tape

or glue. These products can damage the surface of

youricemaker.Formoreinformation,seeImportant

Safety Instructions.

1. POWER ON/OFF - Press to turn the ice machine on or off.

2. ICE MAKING - Glows white when the unit is ON.

3. CHECK WATER - Glows red when there is not water supplied to the machine.

4. TIME TO CLEAN - Glows yellow when it's time to clean the machine. The light will switch ON after 6 months of

use. It will remain on until the ice making system is cleaned using the process in the Care and

Cleaning section.

5. CLEAN RESET -PressedwithPowerbuttonfor5secondstostartthecleaningprocess(seeCareandCleaning).

POWER

ON/OFF

CLEAN

RESET

TIME TO

CLEAN

CHECK

WATER

ICE

MAKING

Packaging

USING THE ICE MACHINE: Packaging/ Controls

1 2 3 4 5

Controls

649-60745 Rev. 4

Starting the ice machine

Ice scoop

Kickplate

Control panel

Ice making area

Frontservicepanel

Initial Start Up

1. Turn on the water supply.

2. Switch on the electrical power.

3.PushandreleasetheON/OFFswitchtostartthe

machine.TheICEMAKINGlightnexttotheON/OFF

switch will glow white.

4. Water will begin to flow into the unit. When the

reservoir is full, water will start to drain from the

machine. After a few minutes the compressor, water

pump and fan motor will begin to operate as the first

ice making cycle begins.

No adjustments are needed.

Inapproximately30minutes,icewillfallintotheice

storage bin. The machine makes 24 gourmet cubes at a

time. It is normal for the first batches of ice to melt as the

bincools.Itwilltake8-10hoursofcontinuousruntime

to fill the ice bin. When the ice bin is full, the ice machine

will shut off. It will automatically restart when the ice level

falls, either from use or normal meltage.

Discard the first bin full of ice.

This machine takes in room temperature air at the lower

right front and forces warm air out the lower left front.

Restricting the airflow or operating the machine in a hot

or cold environment will adversely affect the ability of the

ice machine to make ice.

When the door is opened, the control panel, ice making

area and ice storage bin are visible. The scoop is located

in a holder along the right side wall.

This is a gravity drain model that must have a building

drain connection below the level of the drain tube at the

back of the cabinet. A pump can be installed, which can

forcedrainwaterupamaximumof10feet,allowingit

to be located where a gravity drain isn't available. See

Accessoriesonpage20formoreinformationonthe

drain pump. Warm Air Out Air Intake

Features

USING THE ICE MACHINE:Features/Startingtheicemachine

49-60745 Rev. 4 7

GROUNDING THE ICE MACHINE

WARNING Electrical Shock Hazard.

Failuretofollowtheseinstructionscanresultindeath,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong(grounding)plugwhichmateswithastandard

3-prong(grounding)walloutlettominimizethe

possibilityofelectricshockhazardfromthisappliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall

outlet.

DONOT,UNDERANYCIRCUMSTANCES,CUTOR

REMOVETHETHIRD(GROUND)PRONGFROM

THE POWER CORD.

DONOTUSEANADAPTERPLUGTOCONNECT

THEAPPLIANCETOA2-PRONGOUTLET.

DONOTUSEANEXTENSIONCORDWITHTHIS

APPLIANCE.

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit our Website at: GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Observe all governing codes

and ordinances. Save these instructions for local

inspector’s use.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keeptheseinstructionsfor

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Installation can vary

WaterLineInstallation30

minutes

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

ICE MACHINE LOCATION AND

PREPARATION

This ice machine is designed to be used indoors, in

a controlled environment or outdoors within certain

limits.

It is made up of two major systems: the ice making

system and the ice storage system. The ice making

system is a continuous flow that makes ice when the

ice level becomes low and stops when it is full.

The ice storage system is an insulated chest

with a drain at the bottom for melting ice. It is not

refrigerated, insuring that the bin contains fresh ice.

IMPORTANT: Never keep anything in the ice storage

bin that is not ice. Objects like wine or beer bottles are

not only unsanitary, but the labels can slip off and plug

up the drain.

IMPORTANT: Never allow the machine to operate

without regular cleaning. The machine will last longer

if it is kept clean. Regular cleaning should happen

at least once per year, and preferably twice. Some

water conditions will dictate even more frequent

cleaning of the ice making section, and some carpets

or pets will dictate more frequent cleaning of the

condenser.

Specifications

The ice machine will operate adequately within the

limits, but functions best in temperatures between

70°Fand80°F.

•Minimumairtemperature:50°F(10°C)

•Maximumairtemperature:100°F(38°C)

•Minimumwatertemperature:40°F(4.5°C)

•Maximumwatertemperature:100°F.(38°C)

•Minimumwaterpressure:20psi(1.4bar)

•Maximumwaterpressure:80psi(5.5bar)

Electrical voltage limits:

See the Rating Plate inside the ice machine.

INSTALLATION INSTRUCTIONS

Installation

Instructions ICE MACHINE

849-60745 Rev. 4

Installation Instructions

INSTALLATION INSTRUCTIONS

ICE MACHINE LOCATION AND PREPARATION (Cont.)

Water Quality

All water, including potable water supplied by

municipalities, contains some impurities or minerals.

Water absorbs impurities from the air as rain and/or

as it flows through the ground. Some of the impurities

are solid particles. These are known as suspended

solids, and a fine particle filter will remove them.

Other impurities are chemically bonded to the water

molecules and cannot be filtered out. These are called

dissolved solids.

Ice made by this machine will have a lower mineral

content than the water it was made from. This is due

tothemethodofmakingice.Purerwaterwillfreeze

first in the ice making molds. The reason for this is that

anythingdissolvedinwaterlowersthewater'sfreezing

temperature. This concentrates most of the impurities

of the ice machine water reservoir where they may form

hard deposits known as scale. The machine dilutes the

concentration of minerals by over-filling the reservoir

duringtheharvestcycle(withtheexcesswaterflowing

downthedrain).Waterusevarieswithairandwater

temperatures. Between 2 and 4 pints of water flow into

the unit each cycle. Between 1 and 3.5 pints of that

rinses the reservoir and goes down the drain.

Some impurities will inevitably remain, and will stick to

the parts in the machine. This will cause malformed ice

cubes. Eventually, built up mineral scale can shorten

machine life.

To keep the machine operating properly, these

impurities or minerals will have to be regularly dissolved

by an acid cleaner. Directions for this may be found in

the Care and Cleaning section.

Filters and Treatment

In general, it is always a good idea to filter the water.

A proper water filter can remove taste and odors

as well as particles. We recommend using a GE

AppliancesWaterFilteronyourwaterinletlinesuch

asGEAppliancesModelNumberGXRLQ.Please

go to GEAppliances.com to review the installation

instructions and determine which filter will suit your

application. In Canada visit GEAppliances.ca. Some

other methods of water treatment for dissolved solids

include reverse osmosis, and polyphosphate feeders.

RO Water

This machine can be supplied with Reverse Osmosis

water, but the water conductivity must be no less than

10microSiements/cm.Areverseosmosissystem

should include post treatment to satisfy the R.O. water's

potentialaggressiveness.Deionizedwaterisnot

recommended.

Because water softeners exchange one mineral

for another, softened water may not improve water

conditions when used with ice machines. Where water

is very hard, softened water could result in white,

mushy cubes that stick together.

If in doubt about the water, contact a local point of

use water specialist for recommendations on water

treatment.

Installation Overview

The ice machine must:

- be connected to cold, potable water

- be connected to a drain

- be connected to the proper power supply

- be able to circulate air through the vents at the front

NOTE: Do not build in so that the door is recessed.

49-60745 Rev. 4 9

ADVANCE PLANNING

CAUTION Due to excessive weight, TWO

PEOPLE ARE REQUIRED TO MOVE AND INSTALL

THIS Ice maker. Failure to do so can result in back or

other injury.

Cutout & Product Dimensions

Installation Notes

Built-In Installation: If a finished floor is to be installed

in the area after the ice machine has been built in,

shims the expected thickness of the floor should be

installed under the unit to keep the machine level with

the planned floor level.

NOTE: The water connection is at the back and adds a

few inches to the cabinet depth.

Installation on a slab: You will need to install a drain

pump to the appliance and pump the water to the point

of drainage. See Accessories. Pump models will pump

1story(10feet)hight.

Installation over a crawl space or basement: Either

agravitydrainorapumpmaybeused.Forpump,see

Accessories. If there is not enough room behind the

machine for a drain/waste receptacle, the drain will

have to be below the floor.

NOTE: When installed in a corner, the door swing may

be limited due to handle contact with the wall or cabinet

face.

A water supply is required. Water supplies vary in the

degree of mineral content. High mineral content water

will require more frequent maintenance. Water filtration

may improve the taste of the ice as well as cut down on

some of the mineral build up.

Installation Instructions

INSTALLATION INSTRUCTIONS

10 49-60745 Rev. 4

14 7/8"

AIR IN

AIR OUT

.75

SHEET METAL DOOR FRONT

.63 MIN. CABINET DOOR

29-7/8"

1"

LEG ADJUSTMENT

(4) PLACES

33-7/8

"

22"

2 3/4"

4-3/8"

3 3/4"

1 1/2"

2 1/2" 3 1/4"

7 3/8"

115 V

POWER CORD

DRAIN

FLEXIBLE TUBING

5/8" I.D. x 7/8" I.D.

POTABLE WATER INLET

1/4" COMPRESSION FITTING

3 7/8"

20 3/8"

FLOOR DRAIN

ACCESS HOLE

DIMENSIONS

Installation Instructions

INSTALLATION INSTRUCTIONS

49-60745 Rev. 4 11

DOOR SWING

Moving the hinges allows the door to open from either

the left or the right side. Change the swing BEFORE

attaching the door panel.

To change:

1. Open the door. Remove 4 stainless steel screws

opposite the hinge side on the front of the cabinet.

2. Remove innermost screw holding each hinge to the

cabinet.Loosentheotherscrew.

3. Slide the door to the side so the keyhole on the

hinge clears the screw and remove from cabinet.

4. Remove the screws that were loosened and save.

Install the 4 stainless steel screws that were

removed in Step 1 into the open holes on the

cabinet left by removing the hinge.

5. Remove the hole plug and hinge opening covers

fromdoor(ifapplicable).

6. Remove hole plugs or screws from unit's new hinge

locations(ifapplicable).Setaside.

7. Install the 2 hinge screws removed after the door

was removed from the cabinet into the outermost

holes on the new hinge side of the cabinet. Screw

these in only about half way.

8. Remove the upper hinge from the door and move it

to the door's opposite side, bottom location. Secure

using the original screws.

NOTE: If door panel is attached, it must be

removed to access hinge screws and to reverse

the handle position.

9. Remove the original lower door hinge and move it

to the opposite side, upper location. Secure using

original screws.

IMPORTANT: If installing a stainless steel door

panel or custom panel, skip to INSTALLING THE

DOOR PANEL section.

10.Installpocketcoversandholeplugsontodoor.

11. Place the keyhole slot on the hinge over the

outermost screw, top and bottom, and slide the

door onto the cabinet.

12. Install the door to the cabinet using the original

screws. Tighten all 4 screws.

IMPORTANT: In some situations the door can

open too far and damage adjacent cabinets. To

preventthis,insertaStopPin(inhardwarepacket)

into the provided hole in the top and bottom hinges.

Drive the pin into the hole until the head is flush

with the hinge.

13. Slide the hinge covers from the hardware packet

over each hinge.

14. Attach the side covers from the hardware packet

over the hinge by peeling off the covering over the

adhesive and placing it over the side of the hinge.

NOTE: If the unit is being built-in a screw can be

used to secure the unit to the cabinet in place of

installing the side covers.

Hole plug

Hinge Opening Cover

Remove

Loosen

Door stop pin

Hinge Cover

Side

Cover

Installation Instructions

INSTALLATION INSTRUCTIONS

12 49-60745 Rev. 4

INSTALLING THE DOOR PANEL

The ice machine is supplied without a conventional

door covering, allowing the attachment of a door panel

or a custom panel.

NOTE: If the door swing is to be changed, it needs to

be done BEFORE attaching the door panel.

Door Panel

Finisheddoorpanelswithhandlesareavailablefrom

GE Appliances for attachment to the ice machine. See

Accessoriesonpage20.

A custom panel of wood or other material not

exceeding 15 lbs can be used and must follow these

guidelines:

 width:147/8”

 height:between295/8”and305/8”

 thickness:5/8”to3/4”

For Custom Panel:

1. Measure overall height of the cabinet opening

wheretheicemachinewillbeinstalled(floorto

bottomofthecountertopedge).

2. Determinedesiredtoekickheight(bottomofdoor

tothefloor).Thiscanbeequaltotheadjacent

cabinet’s toekick height.

3. The clearance between the countertop and the top

oftheicemachineshouldbeatleast1/8”.

4. Subtract the toekick height and the clearance from

the opening height to determine the height of your

custom door panel.

5. Cut the panel to the specified width and height.

6. Determine the top of the panel. Measure and mark

hole locations.

7. Drill pilot holes on the back of the panel at your

markings.Useadrillstoptopreventdrilling

through the panel.

Cabinet

opening

1/8”orgreater

clearance

Toekick

height

13-9/16”

8-1/4”

6-25/32”

4-1/8”

1-1/16”

14-15/16”

14-7/8”

Centerline

13-31/64”

30-5/8”

29-5/8”

13/32”

ᴓ1/8”

TYP (10)

13/32”

Installation Instructions

INSTALLATION INSTRUCTIONS

49-60745 Rev. 4 13

INSTALLING THE DOOR PANEL (Cont)

If the door swing is going to be changed please complete prior to installing the door panel. See page 11.

Depending on the door kit being installed, the door handle may need to be flipped if the door swing is being

changed. Please see instructions on page 14 on how to flip the door handle.

Attaching the Door Panel

The panel will be held on by 6 sheet metal screws and

2 machine screws.

1. Remove the gasket from the inside of the door and

retain for later use.

2. Remove any plastic covering the stainless steel

panel.

3. Place the door panel onto the outside of the door

and secure it with 2 machine screws in the left

center and right center of the door.

4.Fastenthepaneltothedoorusingthe6sheet

metal screws. In the hinge opening area opposite

the hinge side, use the outermost screw holes only.

5. Place the covers over the hinge opening areas and

secure each cover to the door using a sheet metal

screw and washer.

6. Insert hole plug over screw installed in step 5.

7. Return the gasket to its original position.

8. Attach the door to the cabinet using the original

screws.

IMPORTANT: In some situations the door can open

too far and damage adjacent cabinets. To prevent

this,insertaStopPin(inhardwarepacket)intothe

provided hole in the top and bottom hinges. Drive the

pin into the hole until the head is flush with the hinge.

9. Slide the hinge covers from the hardware packet

over each hinge.

10.Attachthesidecoversfromthehardwarepacket

over the hinge by peeling off the covering over the

adhesive and placing it over the side of the hinge.

Note: If the unit is being built-in a screw can be

used

to

secure the unit to the cabinet in place of installing

the side covers.

11. Return the kickplate and front service panel to

their original positions and attach to the cabinet

using the original screws.

Hinge Cover

Side Cover

Gasket Machine

Screw

Door

Panel

UseUPPER

hole at the top

Hole Plug Cover

UseLOWER

hole at the

bottom

Stop

Installation Instructions

INSTALLATION INSTRUCTIONS

14 49-60745 Rev. 4

PLUMBING

The recommended water supply tubing is 1/4" OD

copper.StainlesssteelflexorreinforcedPCVtube

may also be used. Install an easily accessible shut-

off valve between the supply and the unit. This shut-

off valve should not be installed behind the unit.

NOTE: Do not use self-piercing type valves.

1. Remove the

front service

panel.

2. Route the

tubing

through the

right hole in

the back to the inlet water solenoid valve inlet.

3. Install a compression fitting on the tubing and

connect to the inlet of the solenoid.

DRAIN PUMP

Drain Installation

A drain pump is available for this ice machine. The

drainpumpkitnumberisUPK3andisavailableat

GEApplianceparts.com or by calling GE

Appliances at 877.959.8688. In Canada visit

GEAppliances.ca or call 800.561.3344.

GRAVITY DRAIN

Drain Installation

NOTICE Restrictions in the drain

system to the machine will cause water to back

up into the ice storage bin and melt the ice.

Gravity drain tubing must be vented, have no

kinks, and slope to the building drain. Air gaps

are typically required by local codes.

1. Place the ice machine in front of the installation

opening. Adjust leveling legs to the approximate

height.ThereareLegCapsinthehardware

packet that can snap onto the leveling legs if

they are going to show when the unit is level.

2. Remove the front service panel and the upper

black panel.

NOTE: If the drain opening has been located in the

floor under the base pan according to the pre-install

specifications, follow steps 3-6 to drain the unit

through the base. If not, proceed to 6.

3. Remove the clamp and barbed elbow and take

off the plastic cover in the base pan below the

drain hose.

Screw

SecuringFront

Service Panel

Installation Instructions

INSTALLATION INSTRUCTIONS

HANDLE REVERSING INSTRUCTIONS

1. Remove the allen wrench from the panel

installation screw kit envelope

2.Loosenthesetscrewusingtheallenwrench.

Remove the handle and flip it around so the logo is

facing the other way.

3. Place the handle caps over the fasteners of the

door. Take care to support the handle so it doesn’t

fall and scratch the appliance finish. Make sure

both handle caps are resting on the face of the

door.

4.Lockoneendofthehandleintopositionby

tightening the set screw in the handle cap with the

allen wrench provided. DO NOT over-tighten.

5.Keepsupportingthehandleasyoulocktheother

end of the handle into position by tightening the set

screw in the handle cap. DO NOT over-tighten.

fastener

handle cap

set screw

LOOSEN

set screw

fastener

handle cap

set screw

LOOSEN

set screw

fastener

handle cap

set screw

LOOSEN

set screw

49-60745 Rev. 4 15

GRAVITY DRAIN (Cont.)

4. Connect a straight 5/8" barbed connector to

the drain hose, securing with the supplied hose

clamp.

5. Cut an 8"piece of 5/8" OD x 7/8" OD tygon

(clearplastic)tubing.Slideoneendofthetube

ontotheclamp,Leavetheotherendofthetube

lying on the floor of the base pan until the unit is

positioned over the floor drain.

6.Routethedraintubeeithera)Insertthedrain

tube through the base pan into the floor drain

orb)Routethedraintubethroughthelefthole

in the lower back panel and connect to barbed

elbow and secure with a clamp.

7. Reinstall the upper back panel.

8.Reinstalltheserviceaccesspanel.Levelthe

unit. ThereareLegCapsinthehardwarepacket

that can snap onto the leveling legs if they are

going to show when the unit is level.

Water Supply

The recommended water supply tubing is 1/4" OD

copper.StainlesssteelflexorreinforcedPCVtube

may also be used. Install an easily accessible shut-

off valve between the supply and the unit. This shut-

off valve should not be installed behind the unit.

The water connection is at the back of the cabinet.

Connect using a compression fitting, one is supplied

tied to the water inlet tube at the back of the cabinet.

When built in: Coil enough tubing behind the

machine so it can be pushed into the cavity without

kinking the tubing.

Drain

Hose

Drain Hose,

Route to

building drain

Barbed

Elbow

Water Inlet

Tube(field

supplied)

Installation Instructions

INSTALLATION INSTRUCTIONS

PLACEMENT OF THE ICE

MACHINE

The ice machine is supplied with a power cord.

Do not remove the grounding pin from the cord's

plug.Donotuseextensioncords.Followallcodes.

Connect the machine so its own 115v, 15amp

circuit.

1. If the electrical outlet for the ice maker is behind

the unit, plug it into the unit.

2. Position the unit in the installation opening.

3. Turn on the water supply. Make sure that the

icemaker is plugged in and the power is on.

4. Slide the unit into the installation opening,

paying special attention to water supply and drain

connections. Do not kink!

5. Pour a couple of quarts of water into the ice

storagebin;ondrainpumpequippedmachines

the drain pump should start and water should

pump out. Check for leaks.

6. Replace the service access panel.

7.Leveltheunitasneeded.

16 49-60745 Rev. 4

Cleaning the Outside

The stainless steel door and door handle can be cleaned

with a commercially available stainless steel cleaner.

CleanerswithoxalicacidsuchasBarKeepersFriend

Soft Cleanser™ will remove surface rust, tarnish and

small blemishes.

Useonlyaliquidcleanserfreeofgritandrubinthe

direction of the brush lines with a damp soft sponge. Do

not use appliance wax or polish on the stainless steel.

Cleaning the Condenser

The condenser has fins and tubes that can become

clogged with dirt and lint.

NOTE: Outdoor operation can lead to rapid buildup

of debris, such as leaves and other vegetation. The

condenser will need to be frequently checked for debris.

Clean it whenever the fins are obstructed.

To clean:

1. Remove the kickplate and front service panel.

2.Locatethecondensersurface.

3.Vacuumthesurfacetoremovealldust,dirt,andlint.

NOTICE Do not dent the fins.

4. Return the kickplate and front service panel to their

originalpositions.Fastenthemtothecabinetusing

the original screws.

Condenser surface

Cleaning the Ice Storage Bin

Theicestoragebinshouldbesanitizedoccasionally.

Itisusuallyconvenienttosanitizethebinaftertheice

making system has been cleaned and the bin is empty.

Asanitizingsolutioncanbemadeof1ozofhousehold

bleachand2gallonsofhot(95°F-115°F)water.Use

a clean cloth and wipe the interior of the ice storage bin

withthesanitizingsolution.Poursomeofthesolution

down the drain.

Allow to air dry.

Winterizing

1. Clean the ice making system per the instructions

above.

2. Open the door. Push the ON/OFF button to turn the

ice machine off.

3. Turn off the water supply.

4. Drain the water reservoir by removing the rubber

stopper under the reservoir. It is located near the

back wall of the ice storage bin.

5. Disconnect the incoming water line at the inlet water

valve.

6. Open the door. Push the ON/OFF button to turn the

ice machine on.

7. Blow air through the inlet water valve. A tire pump can

be used.

8. Models with a drain pump installed should have about

1/2gallonofRVantifreeze(propyleneglycol)poured

into the ice storage bin drain.

NOTE: AutomotiveantifreezemustNOTbeused.

9. Turn off and unplug the machine.

Rubber stopper

Care And Cleaning

CARE AND CLEANING

49-60745 Rev. 4 17

Removing Scale from the Ice Making System

TheTIMETOCLEANlightwillcomeonafter6months

of use. It will remain on until the ice making system has

been cleaned.

You should use rubber gloves when using the scale

remover. To order scale remover, go to

GEAppliances.com or call GE Appliances at

800.GECARES(800.432.2737). In Canada visit

GEAppliances.ca or call 800.661.1616. Order part

numberWX08X42873.

1. Scoop out all of the ice in the ice bin. Discard the ice

or save it in an ice chest or cooler.

2. Press and hold the ON/OFF button for 3 seconds

until the white light goes out.

3. Press and hold both the CLEAN-RESET and ON/

OFF buttons for 5 seconds. The TIME TO CLEAN

light will blink on and off.

4. Pour8ozoficemachinescaleremoverintotheice

machine reservoir.

5. Operate the machine for about 1/2 hour.

6. Push and release the ON/OFF switch. The machine

will begin to flush out the cleaning solution.

7. Operate the machine for another 1/2 hour.

8. Push and release the ON/OFF switch. The machine

will stop the cleaning process.

9. Pour a gallon of hot water into the bin to flush out

the drain.

10. Clean the bin liner of mineral scale by mixing some

ice machine scale remover and hot water, and using

that solution to scrub the scale off of the liner.

11. Rinse the liner with hot water.

12.Sanitizethebininterior.

13. Replace the ice removed in step 1 if applicable.

14. Push and release the ON/OFF button to restart ice

making.

15. The ice scoop should be washed regularly and is

dishwasher safe.

Normal gourmet cubes are tapered cylinders. If the

gourmet cubes are ragged and miss-shaped, mineral

scale must be removed from the ice making system.

NOTE: The bin is insulated and not refrigerated so the

ice form will change in the storage bin as it is normal for

the ice to melt.

POWER

ON/OFF

CLEAN

RESET

TIME TO

CLEAN

CHECK

WATER

ICE

MAKING

WARNING

Ice machine scale remover contains acids. Acids

can cause burns. If concentrated cleaner comes

incontactwithskin,ushwithwater.Ifswallowed,

do NOT induce vomiting. Give large amounts of

waterormilk.CallPhysicianimmediately.Keep

out of the reach of children.

Pour scale remover

Care And Cleaning (Cont.)

CARE AND CLEANING

18 49-60745 Rev. 4

Problem Possible Causes What to Do

Ice cubes are incompletely

formed

Scale on the ice making system Clean the ice making system

Low capacity Restricted drain or standing water in

the bin

Clean the air cooled condenser fins.

Clean the ice making system.

Check the drain line for kinks

No ice SwitchisOFF Press the ON/OFF button to turn the

power on.

Electric breaker has been tripped Fliptheelectricbreakerbackon.

Water supply is low If the Check Water light is flashing

Red, the water supply is low. The

control system checks for water every

20minutes.Whenthewatersupplyis

restored, the machine will automatically

reset.

Time to Clean light is on Clean the ice making system following

directions in the Care and Cleaning

section.

Noise

The ice machine is designed for quiet operation but will

make some noise during the ice making cycle. During a

freezingcycle,itisnormaltohearthefanmovingairand

the water pump circulating water. Ice hitting the bin or ice

in the bin can be heard during harvest.

Troubleshooting Tips... Before you call for service

TROUBLESHOOTING TIPS

Save time and money! Review the charts on the following pages first and you may not need to call for service.

49-60745 Rev. 4 19

■ Service trips to your home to teach you how to use the

product.

■ Improper installation, delivery or maintenance.

■Failureoftheproductifitisabused,misused,or

used for other than the intended purpose or used

commercially.

■ Replacement of house fuses or resetting of circuit

breakers.

■ Damage caused after delivery.

■ Replacement of the light bulbs, if included.

■ Damage to the product caused by accident, fire, floods

or acts of God.

■ Incidental or consequential damage caused by

possible defects with this appliance.

■ Product not accessible to provide required service.

What GE Appliances Will Not Cover:

For the Period of: GE Appliances Will Replace

One Year

Fromthedateofthe

original purchase

Any part of the ice machine which fails due to a defect in materials or workmanship.

During the limited one-year warranty, GE Appliances will also provide, free of charge, all labor

and related service to replace the defective part.

FiveYears

Fromthedateofthe

original purchase

Any part of the sealed refrigeration system(thecompressor,condenser,evaporatorandall

connectingtubing)whichfailsduetoadefectinmaterialsorworkmanship.

During the limited five-year sealed refrigerating system warranty, GE Appliances will also

provide, free of charge, all labor and related service to replace the defective part in the sealed

refrigerating system.

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

GEAppliances.com

AllwarrantyserviceisprovidedbyourFactoryServiceCenters,oranauthorizedCustomerCare® technician. To schedule

service online, visit us at GEAppliances.com,orcallGEAppliancesat800.GE.CARES(800.432.2737).Pleasehave

yourserialnumberandyourmodelnumberavailablewhencallingforservice.InCanada,call800.661.1616.

LIMITED WARRANTY

GE Appliances Ice Machine Limited Warranty

EXCLUSION OF IMPLIED WARRANTIES

YoursoleandexclusiveremedyisproductrepairasprovidedinthisLimitedWarranty.Anyimpliedwarranties,

including the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or

the shortest period allowed by law.

For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for products

purchasedforhomeusewithintheUSA.IftheproductislocatedinanareawhereservicebyaGEAppliancesAuthorized

Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an

AuthorizedGEAppliancesServicelocationforservice.InAlaska,thelimitedwarrantyexcludesthecostofshippingor

service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you

specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights

are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: GE Appliances, a Haier company

Louisville, KY 40225

For Customers in Canada: This limited warranty is extended to the original purchaser and any succeeding owner

for products purchased in Canada for home use within Canada. In-home warrant service will be provided in areas

where it is available and deemed reasonable by Mabe to provide.

Warrantor Canada: MC Commercial, Burlington, Ontario, L7R 5B6

20 49-60745 Rev. 4

ACCESSORIES

Accessories

Looking For Something More?

Finishedstainlesssteeldoorpanelswithhandlesare

available from GE Appliances for attachment to the ice

machine.The panel kits are:

•ZIP80SS-StainlesssteeldoorwithEuroStyle

Handles

•PIP70SS-StainlesssteeldoorwithProfileStyle

Handles

• CIP75S1 - Stainless steel door with Café Style

Handles

• CIP75D1 - Matte black with Café style handle

• CIP75W2 - Matte white with Café style handle

In addition we also offer the following Café handle kits:

•CXXN1H1PNBT-Blackhandle

•CXXN1H1PNZ-Bronzehandle

•CXXN1H1PNCU-Copperhandle

NOTE: These kits only work with the CIP family of door

kits.

To order, go to GEApplianceParts.com or call

877-959-8688. In Canada visit

GEAppliances.ca/en/

products/parts-filter-accessories

orcall800.661.1616.

Kickplate Extension: In some situations the leg levelers

will be extended enough to become visible. A kit to extend

the kickplate over the legs is available. That kit number is

WR02X25708.To order, go to GEApplianceParts.com

or call 877-959-8688. In Canada visit

GEAppliances.ca/en/products/parts-filter-accessories

or call 800.661.1616.

Cabinet Stability: In some free standing installations it

may be prudent to add an anti-tip bracket that secures

the back of the cabinet to a wall. That kit number is

WR01X25709. To order, go to GEApplianceParts.com

or call 877-959-8688. In Canada visit

GEAppliances.ca/en/products/parts-filter-accessories

or call 800.661.1616.

Drain Conversion: A gravity drain model can be

converted to a drain pump model by installing a drain

pump kit. The drain pump kit consists of a drain pump,

wiring harness and associated tubing. The part number

is UPK3. To order, go to GEApplianceParts.com or call

877-959-8688. In Canada visit

GEAppliances.ca/en/products/parts-filter-accessories

or call 800.661.1616.

La page est en cours de chargement...

GE UCC15NJII Guide d'installation

GE UCC15NJII Guide d'installation

dans d''autres langues