Desa Tech M30016AW Le manuel du propriétaire

Marque: Desa Tech

Modèle: M30016AW

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

IMPORTANT: Read and understand this manual before

assembling or operating this chain saw. Improper use of

saw can cause severe injury. Keep this manual for future

reference.

MODELS: M15012US, M15014AS, M30016US, M30016AS,

M30016AW, M35016AW

ELECTRIC CHAIN SAW

OWNER’S MANUAL

ENGLISH

For parts contact: www.PartsFor.com

www.remingtonpowertools.com

ENGLISH

CONTENTS

IMPORTANT SAFETY INFORMATION ....................................................................... 4

Before Operating Saw ............................................................................................................... 4

While Operating Saw ................................................................................................................. 4

Kickback .................................................................................................................................... 5

Maintenance and Storage of Chain Saw ................................................................................... 6

UNPACKING ................................................................................................................ 6

PRODUCT IDENTIFICATION ...................................................................................... 7

CHAIN SAW NAMES AND TERMS ............................................................................. 8

QUICK START GUIDE................................................................................................. 9

ASSEMBLY ................................................................................................................ 10

SAW CHAIN TENSION ADJUSTMENT .................................................................... 12

OPERATING CHAIN SAW ......................................................................................... 13

Filling Oil Tank ......................................................................................................................... 13

Oiling Chain ............................................................................................................................. 13

Clearing sprocket cover of debris ............................................................................................ 13

Extension Cords ...................................................................................................................... 14

Cutting with the Chain Saw .....................................................................................................14

Felling a Tree (Cutting Down a Tree) ...................................................................................... 15

Limbing a Tree ......................................................................................................................... 16

Bucking a Log .......................................................................................................................... 16

Trimming a Tree (Pruning) ....................................................................................................... 17

CLEANING AND MAINTENANCE ............................................................................ 18

Cleaning Saw Body ................................................................................................................. 18

Care of Guide Bar ................................................................................................................... 18

Sharpening Saw Chain ............................................................................................................ 18

Replacing Saw Chain .............................................................................................................. 19

STORAGE .................................................................................................................. 20

REPLACEMENT PARTS AND ACCESSORIES ....................................................... 20

REPAIR SERVICE ..................................................................................................... 20

Warranty Service ..................................................................................................................... 20

Non-Warranty Service ............................................................................................................. 20

TROUBLESHOOTING ............................................................................................... 21

TECHNICAL SERVICE .............................................................................................. 21

WARRANTY INFORMATION ..................................................................................... 22

ILLUSTRATED PARTS BREAKDOWN ..................................................................... 72

PARTS CENTRAL ..................................................................................................... 74

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

IMPORTANT SAFETY INFORMATION

BEFORE OPERATING SAW

1. Read and understand this owner’s manual

before operating chain saw.

2. Watch what you are doing. Use common

sense. Do not operate saw when you are

tired.

3. Use chain saw for cutting wood only. Do not

use chain saw for purpose not intended. Do

not use for cutting plastic, masonry, etc.

4. Only well-instructed adults should operate

chain saw. Never allow children to operate

chain saw.

5. Use only electrical voltage noted on model

plate of chain saw.

6. Use only extension cords marked for outdoor

use. See Extension Cord Requirements.

7. Do not operate chain saw

• while under the inﬂuence of alcohol, medi-

cation, or drugs

• in rain or in damp or wet areas

• where highly ﬂammable liquids or gases are

present

• if saw is damaged, adjusted wrong, or not

fully and securely assembled

• if trigger does not turn saw on and off. Chain

must stop moving when you release trigger.

Have faulty switch replaced by authorized

service center (see Technical Service).

• while in a hurry

• while in tree or on a ladder unless trained to

do so

8. Wear snug-ﬁtting clothes when operating

chain saw. Do not wear loose clothing or

jewelry. They can get caught in moving saw

chain.

9. Wear the following safety gear when operating

chain saw.

WARNING: When using an electric

chain saw, basic safety precautions

should always be followed to reduce

the risk of ﬁ re, electric shock, and

injury to persons, including the fol-

lowing:

READ ALL INSTRUCTIONS.

Make sure you read and understand all

instructions in Important Safety Infor-

mation. Improper use of this chain saw

can cause severe injury or death from

ﬁre, electrical shock, body contact with

moving chain, or falling wood.

• heavy-duty gloves (wear rubber gloves

when working outdoors)

• steel-toed safety footwear with non-skid

soles

• eye protection such as safety glasses,

goggles, or face screen

• safety hard hat

• ear mufﬂers or ear plugs

• hair covering to contain long hair

• face or dust mask (if working in dusty

areas)

10. Before cutting, always provide the follow-

ing:

• clear work area

• secure footing

• planned retreat path from falling tree

11. Inspect tree before cutting down. Make sure there

are no dead limbs or branches that may fall on

you.

12. To reduce the risk of electric shock, this saw

has a polarized plug (one blade is wider than

the other). This plug will ﬁ t in a polarized

outlet only one way. If the plug does not ﬁ t

fully in the outlet of your extension cord,

reverse the plug. If it still does not ﬁ t, a polar-

ized extension cord will be necessary. Do not

change the plug in any way.

WHILE OPERATING SAW

1. Stay alert. Use common sense while operating

chain saw.

2. Keep work area clean. Cluttered areas invite

injuries.

3. Be aware of extension cord while operating

chain saw. Be careful not to trip over cord.

Keep cord away from chain and operator at

all times.

4. Keep children, animals, and bystanders away

from chain saw and extension cord. Only

chain saw user should be in work area.

5. Do not cut down a tree unless you are trained

or have expert help.

6. If two or more persons perform bucking and

felling operations at the same time, provide

plenty of distance between operations. Provide

distance of at least twice the height of tree

being felled.

7. Secure wood you are cutting by using clamps

or chocks.

8. Grip chain saw ﬁrmly with both hands. Never

operate chain saw with one hand. Never use

hand guard as handle.

9. Keep ﬁnger off trigger until ready to make

cut.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

90° Quadrant

Do Not Let

Guide Bar

Touch Here

Direction

IMPORTANT SAFETY INFORMATION

WARNING: Kickback may occur

when the nose or tip of the guide bar

touches an object, or when the wood

closes in and pinches the saw chain

in the cut. Tip contact in some cases

may cause a lightning fast reverse

reaction, kicking the guide bar up and

back towards the operator. Pinching the

saw chain along the top of the guide

bar may push the guide bar rapidly

back towards the operator. Either of

these reactions may cause you to lose

control of the saw which could result

in serious injury to user.

KICKBACK

10. Before starting chain saw, make sure chain is

not touching anything.

11. To guard against electrical shock, avoid body

contact with grounded objects such as pipes,

fences, and metal posts.

12. Keep all parts of body away from chain when

saw is running.

13. Do not force chain saw while cutting. Apply

light pressure. It will do the job better and

safer at the rate for which it was intended.

14. Cut small brush and saplings with extreme

care. Slender material may catch in chain and

be whipped toward you. This could also pull

you off balance.

15. When cutting limb or tree trunk that is under

tension, use extreme caution. Be alert for

wood springing back. When wood tension is

released, limb could spring back and strike

operator causing severe injury or death.

16. Carry chain saw from one place to another

• with saw stopped and unplugged

• by holding front handle (never use hand

guard as handle)

• with ﬁnger off trigger

• with guide bar and chain to rear

Kickback Safety Devices On This

Saw

This saw has a low-kickback chain and reduced

kickback guide bar. Both items reduce the chance

of kickback. Kickback can still occur with this

saw.

Follow assembly instructions. Do not remove

front hand guard. Do not replace front hand guard

with substitute.

The following steps will reduce the risk of kick-

back.

• Use both hands to grip saw while saw is

running. Use ﬁrm grip. Thumbs and ﬁngers

must wrap around saw handles.

• Keep all safety items in place on saw. Make

sure they work properly.

• Do not overreach or cut above shoulder

height.

• Keep solid footing and balance at all

times.

• Stand slightly to left side of saw. This keeps

your body from being in direct line with

chain.

WARNING: Some dust created by

power sanding, sawing, grinding, drill-

ing, and other construction activities

contains chemicals known (to the state

of California) to cause cancer, birth

defects, or other reproductive harm.

Some examples of these chemicals

are:

• lead from lead-based paints

• crystalline silica from bricks and ce-

ment and other masonry products

• arsenic and chromium from chemi-

cally-treated lumber

Your risk from these exposures varies,

depending on how often you do this

type of work. To reduce your exposure

to these chemicals: work in a well ven-

tilated area, and work with approved

safety equipment, such as those dust

masks that are specially designed to

ﬁ lter out microscopic particles.

WARNING: This product contains

chemicals known to the State of Cali-

fornia to cause cancer or birth defects,

or other reproductive harm.

Figure 1 - Kickback Hazard Example: Do Not

Let Nose of Guide Bar Touch Object While

Chain is Moving

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

Chain Tensioning Screw

Rear Handle

Power Cord

Guide Bar

Saw Chain

Front Handle

Oil Cap

Trigger

Switch Lockout

Cord Hitch

Guide Bar Nose

Hand Guard

Chain Tensioning Screw

Rear Handle

Power Cord

Guide Bar

Saw Chain

Front Handle

Oil Cap

Trigger

Switch Lockout

Cord Hitch

Guide Bar Nose

Hand Guard

PRODUCT IDENTIFICATION

Models: M15012US, M15014AS, M30016US, M30016AS

Models: M30016AW, M35016AW

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

Bucking Process of cutting a felled tree or log

into lengths.

Chock Block or wedge used to secure wood from

moving.

Felling Process of cutting down a tree.

Felling Cut Final cut when felling a tree. Make this

cut on opposite side of tree from notching cut.

Front Handle Located at front of saw body.

Front Hand Guard Shield between front handle

and guide bar. Protects left hand while using

saw.

Guide Bar Metal bar that extends from saw body.

The guide bar supports and guides chain.

Guide Bar Nose Tip or end of guide bar.

Guide Bar Retainer Bolt-like fastener that holds

guide bar in place during assembly and operation

of chain saw.

Kickback Quick backward and upward motion

of guide bar. Kickback may occur when tip of

guide bar touches an object while chain is mov-

ing. The guide bar will kick up and back towards

operator.

Limbing Process of cutting limb(s) from a felled

tree.

Low-Kickback Chain Chain that reduces chance of

kickback as required by ANSI B175.1.

Normal Cutting Position Stance used while making

bucking and felling cuts.

Notching Cut Notch cut in tree that directs fall of

tree.

Oiler Control System for oiling guide bar and

chain.

Power Head Chain saw without chain and guide

bar. Also known as saw body.

Pushback (Kickback, Pinch) Rapid pushback of

chain saw. Pushback may occur if chain along

top of guide bar is pinched, caught, or contacts a

foreign object.

Rear Handle Handle located at rear of saw

body.

Reduced Kickback Guide Bar Guide bar that

reduces chance of kickback.

Replacement Chain Chain that complies with

ANSI B175.1 when used with a speciﬁc saw. It

may not meet ANSI requirements when used with

other saws.

Saw Chain (Chain) Loop of chain having cutting

teeth for cutting wood. The motor drives chain.

The guide bar supports chain.

Spiked Bumper (Spike) Pointed teeth at front of

saw body beside guide bar. Keep spiked bumper

in contact with wood when felling or bucking. It

helps maintain position of saw while cutting.

Sprocket Toothed wheel that drives chain.

Switch Device that completes or interrupts electri-

cal circuit to motor of saw.

Switch Linkage This device connects switch

to trigger. It moves switch when you squeeze

trigger.

Switch Lockout Device that reduces accidental

starting of saw.

Trigger Device that turns saw on and off. Squeez-

ing trigger turns saw on. Releasing trigger turns

saw off.

Trimming (Pruning) Process of cutting limb(s)

from a living tree.

Undercut An upward cut from underside of log or

limb. This is done while in normal cutting position

and cutting with top of guide bar.

Unibody Main body of chain saw.

CHAIN SAW NAMES AND TERMS

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

When chain becomes loose due to stretching,

tension properly. See Saw Chain Tension

Adjustment for correct tensioning of saw

chain.

Use both hands to grip chain saw. Push

lockout button forward with right thumb and

squeeze trigger. Make sure saw is running

at full speed before starting a cut.

Switch Lockout Button

Trigger

Connect extension cord to power cord and

power supply. Use built-in cord hitch or

knot method (inset) to secure together. See

Extension Cords for correct size.

Power

Cord

Hitch

Extension Cord

Slot

Pour motor oil (see Filling Oil Tank, page

10, for correct oil type) in oil tank (do not

use standard bar and chain oil). DO NOT

leave oil in tank when not in use.

Oil Bottle

Oil Squeeze Bulb

For complete information concerning your saw and its proper

usage, read and understand this owner’s manual thoroughly.

QUICK START GUIDE

If you are familiar with chain saws, their proper usage, and the saw you purchased is fully assembled,

use this Quick Start Guide to quickly begin using your new Remington brand chain saw.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

Towards

Guide Bar

Nose

Cutting

Edge

Guide Bar

Chain Tensioning

Screw

Turn tensioning

screw to move

Adjustment Block

Guide Bar Retainer

Rotated 90 Degrees to

Guide Bar Slot

Guide Bar

Drive Sprocket

Guide Bar Retainer

Positioned Parallel

to Guide Bar Slot

Guide Bar

Drive Sprocket

Note: Some models are pre-assembled. Assembly

is not needed on these models. See Saw Chain

Tension Adjustment

1. Lay chain out ﬂat.

2. Loosen and remove guide bar nut and sprocket

cover.

3. Rotate guide bar retainer so that it is positioned

parallel to guide bar slot (see Figure 2).

4. Install guide bar onto saw body. Assemble

center slot of guide bar onto guide bar bolt

and guide bar retainer. Note: Make sure the

head of the guide bar retainer slides through

the guide bar slot as shown in Figure 2.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

IMPORTANT: Do not clamp chain saw

in vise during assembly.

Figure 3 - Locking Guide Bar Retainer

5. Rotate guide bar retainer 90 degrees as shown

in Figure 3.

Figure 2 - Unlocking Guide Bar Retainer

ASSEMBLY

Figure 5 - Chain Tensioning Screw and

Adjustment Block Location

7. Before installing sprocket cover to saw body,

turn the chain tensioning screw fully counter-

clockwise until it stops. This will position the

adjusting block towards the end of the chain

tensiong screw. (See Figure 5)

Figure 4 - Saw Chain Direction

6. Place chain around drive sprocket, along top

groove of guide bar, and around guide bar nose.

Note: Make sure cutting edges of chain are

facing in right direction. Position chain so

cutting edges on top of guide bar face guide

bar nose (see Figure 4 and indicator on side

cover of saw).

CAUTION: Do not place chain

on saw backwards. If chain is back-

wards, saw will vibrate badly and will

not cut.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

Guide Bar

Adjusting

Hole

Sprocket Cover Tab

Tab Slot

Sprocket Cover Tab

Guide

Bar Nut

9. Insert the sprocket cover tab into the saw body

tab slot, Step 1. Then lower sprocket cover

onto guide bar bolt, Step 2 (See Figure 7).

NOTE: At this point the sprocket cover will

not be ﬂ ush against the saw body.

10. Finger tighten the guide bar nut onto the guide

bar bolt. (See Figure 8).

Figure 8 - Guide Bar Bolt

11. Slowly slide guide bar into saw body until the

adjustment block goes into the round adjusting

hole on the guide bar. (See Figure 6) NOTE:

This locks the guide bar in place. You should

not be able to push or pull the guide bar.

12. Retighten the bar nut ﬁ nger tight.

13. Adjust the saw chain tension. Follow the steps

under Saw Chain Tension Adjustment..

Figure 7 - Installing Sprocket Cover

Figure 6 - Pulling Guide Bar

8. Pull the guide bar away from the saw body

so that the guide bar is fully extended and the

slack is removed from the chain. (See Figure

ASSEMBLY

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

❶

Loosen nut...

If chain becomes loose around guide

bar, allow chain to cool then...

❷

Turn chain tensioning screw

clockwise to tension saw chain...

❸

Pull chain to check tension. Guide

links should not come out of guide

bar groove...

Tighten nut with wrench. A

slight sag of 1/8" between chain

and bottom of guide bar is

acceptable.

❺

❹

Guide Bar

Approx.

5/32"

WARNING: Unplug chain saw from

power source before adjusting saw

chain tension.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

WARNING: Maintain proper

chain tension always. A loose chain

will increase the risk of kickback. A

loose chain may jump out of guide

bar groove. This may injure operator

and damage chain. A loose chain will

cause chain, guide bar, and sprocket

to wear rapidly.

IMPORTANT!

Failure to follow these instructions when ten-

sioning saw chain will damage saw and void the

warranty. For additional information call 1-800-

626-2237.

New saw chains will stretch. Check chain tension

frequently when ﬁ rst used and tighten when chain

becomes loose around guide bar.

SAW CHAIN TENSION ADJUSTMENT

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

Oil Bottle

Oil Squeeze Bulb

Wood Chips,

Twigs, and Debris

Sprocket Cover

Guide Bar Nut

OPERATING CHAIN SAW

WARNING: Read and understand

this owner’s manual before operat-

ing this saw. Make certain you read

and understand all Important Safety

Information. Improper use of this

chain saw can cause severe injury

or death from ﬁre, electrical shock,

or body contact with moving chain,

or falling wood.

FILLING OIL TANK

1. Remove oil cap.

2. Fill oil tank with SAE #30 motor oil. Note:

For temperatures below 30°F, use SAE #10

oil. For temperatures above 75°F, use SAE

#40 oil.

DO NOT use standard bar and chain oil.

3. Replace oil cap at once. Tighten oil cap ﬁrmly

for good seal. This will avoid oil seepage from

cap.

4. Wipe off excess oil.

Figure 9 - Oil Squeeze Bulb and Oil Bottle

Location

CLEARING SPROCKET COVER OF

DEBRIS

While operating the chain saw, wood chips, small

twigs, and other debris can occasionally build up

inside the sprocket cover. To properly maintain the

saw and keep it in good working order, periodic

removal of this debris may be required. To prop-

erly clear debris from the sprocket cover:

1. Unplug chain saw.

2. Loosen and remove guide bar nut (see Figure

10).

3. Turn chain tensioning screw counterclockwise

to loosen chain until sprocket cover is easily

removed.

4. After sprocket cover is removed, clear all

chips, twigs, and debris.

WARNING: Use caution when

clearing debris that is around chain.

Cutting edges on chain are sharp.

Use protective gloves when working

around or handling chain.

5. Once debris has been removed, follow steps 7

through 13 on pages 9 and 10 in the Assembly

section to re-assemble the sprocket cover to

the chain saw.

Figure 10 - Removing and Clearing Sprocket

Cover of Debris

OILING CHAIN

Manual Oil System

Always check oil level before using saw. Do not

attempt to operate the oil system while saw is

in operation. To oil chain, press squeeze bulb.

Oil will feed onto the guide bar and chain. Press

squeeze bulb at least once before each cut. Check

oil level often by looking at oil level through side

of oil bottle (see Figure 9).

Note: It is normal for oil to seep when saw

is not in use. It is necessary to empty oil

tank after each use to prevent seepage.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

Power Cord

Extension Cord

Cord Hitch

Trigger

Switch Lockout Button

Figure 11 - Looping Extension Cord over

Cord Hitch

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 16 AWG

150 feet 14 AWG

Models: M15012US, M15014AS

Keep cord away from cutting area. Make sure cord

does not catch on branches or logs during cutting.

Inspect cords often. Replace damaged cords.

This chain saw is designed with an extension cord

hitch that prevents the extension cord from being

pulled loose during use. To use, form a loop with

the end of the extension cord, insert loop into slot in

rear of handle, and place loop over cord hitch (see

Figure 11. Gently pull loop against cord hitch

until slack is removed. Plug extension cord into

chain saw cord.

EXTENSION CORDS

Use proper extension cords with this saw. Use only

extension cords marked for outdoor use. The cord

must be marked with sufﬁx W or W-A following

the cord type designation. Example: SJTW-A

or SJTW.

Use proper sized cord with this saw. Cord must be

heavy enough to carry current needed. An undersized

cord will cause voltage drop at saw. Saw will lose

power and overheat. Follow cord size requirements

listed below.

Cord Length AWG Cord Size

25 feet 16 AWG

50 feet 16 AWG

100 feet 14 AWG

150 feet 12 AWG

Models: M30016US, M30016AS, M30016AW,

M35016AW

Figure 12 - Lockout Button and Trigger

Location

CUTTING WITH THE CHAIN SAW

1. Connect saw to extension cord. Connect exten-

sion cord to power supply.

2. Make sure section of log to be cut is not laying

on ground. This will keep chain from touch-

ing ground as it cuts through log. Touching

ground with moving chain will dull chain.

3. Use both hands to grip saw. Always use left

hand to grip front handle and right hand to

grip rear handle. Use ﬁrm grip. Thumbs and

ﬁngers must wrap around saw handles (see

Figure 12).

4. Make sure your footing is ﬁrm. Keep feet

apart. Divide your weight evenly on both

feet.

5. When ready to make a cut, push the lockout

button completely forward with the right

thumb and squeeze the trigger (see Figure 12).

This will turn saw on. Releasing trigger will

turn saw off. Make sure saw is running at full

speed before starting a cut.

6. When starting a cut, place moving chain against

wood. Hold saw ﬁrmly in place to avoid possible

bouncing or skating (sideways movement) of

saw.

7. Guide saw using light pressure. Do not force

saw. The motor will overload and can burn

out. It will do the job better and safer at the

rate for which it was intended.

8. Remove saw from a cut with saw running

at full speed. Stop saw by releasing trigger.

Make sure chain has stopped before setting

saw down.

9. Practice until you can maintain a steady, even

cutting rate.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

Direction of Fall

Retreat Path

45°

Tree

Direction

of Fall

Hinge

(5 cm)

2"(5 cm)

2nd Cut -

Upper Notch Cut

1st Cut -

Lower Notch

Cut

3rd Cut -

Felling Cut

Felling is the process of cutting down a tree. Make

sure your footing is ﬁrm. Keep feet apart. Divide

your weight evenly on both feet. Follow directions

below to fell a tree.

Before Felling a Tree

1. Before felling, inspect tree. Make sure there

are no dead limbs or branches that may fall

on you. Study natural lean of tree, location of

larger branches, and wind direction. This will

help you judge which way tree will fall.

2. Clear work area around tree.

3. Plan and clear a retreat path before felling.

Make retreat path opposite to planned direc-

tion of fall of tree and at 45° angle (see Figure

13).

WARNING:

• Avoid kickback. Kickback can result

in severe injury or death. See Kickback

to avoid risk of kickback.

• Do not fell a tree without ample skill

or expert help.

• Keep children, animals, and bystand-

ers away from area when felling a

tree.

• If two or more persons perform

bucking and felling operations at

the same time, provide ample dis-

tance between operations. Provide

distance of at least twice the height

of tree being felled.

WARNING: When felling a tree, be

aware of your surroundings. Do not

endanger any person, strike utility

lines, or cause property damage. If

tree strikes utility lines, contact utility

company at once.

FELLING A TREE (Cutting Down a Tree)

Figure 13 - Retreat Path From Tree

OPERATING CHAIN SAW

Figure 14 - Felling A Tree

4. Remove dirt, stones, loose bark, nails, staples,

and wire from tree where you will make felling

cuts.

WARNING: Do not cut all the way

through tree. Leave about two inches

of tree diameter uncut directly behind

felling notch (see Figure 14). This

uncut portion acts as a hinge. The

hinge helps keep tree from twisting

and falling in wrong direction.

B) Felling Cut

1. Make felling cut two inches higher than lower

notch cut and on opposite side of tree (see Figure

14). Keep felling cut parallel to lower notch

cut.

5. Stay on uphill side when felling tree. Tree

could roll or slide downhill after falling.

Felling Procedure

A) Felling Notch

A properly placed felling notch will determine

direction tree will fall. Place felling notch on

side of tree in direction you want tree to fall (see

Figure 14). Follow directions below to create a

felling notch.

1. Make lower notch cut as close to ground as

possible. Hold saw so guide bar is horizontal.

Cut 1/3 the diameter of tree trunk (see Figure

14). Note: Always make this horizontal lower

notch cut ﬁrst. If you make this cut second,

tree can pinch chain or guide bar.

2. Start upper notch cut the same distance above

ﬁrst cut as ﬁrst cut is deep.

Example: If lower notch cut is eight inches deep,

start upper notch cut eight inches above it. Cut

downward at 45° angle. The upper notch cut

should meet end of lower notch cut (see Figure

14).

Remove tree trunk wedge created by notching

cuts.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

Limbing is removing branches from a fallen tree.

Make sure your footing is ﬁrm. Keep feet apart.

Divide your weight evenly on both feet. Do not

remove larger limbs under tree that support log

off ground. Remove each limb with one cut (see

Figure 15). Clear cut limbs from work area often.

This will help maintain a safe work area.

Make sure you start your cut where limb will

not pinch saw during cutting. To avoid pinching,

start cut on freely hanging limbs from above

limb. Start cut on limbs under tension from under

limb. If pinch occurs, turn saw off, lift limb, and

remove saw.

WARNING: When cutting limb that

is under tension, use extreme caution.

Be alert for wood springing back.

When wood tension is released, limb

could spring back and strike operator

causing severe injury or death.

LIMBING A TREE

WARNING: Avoid kickback. Kick-

back can result in severe injury or

death. See Kickback to avoid risk of

kickback.

WARNING: Be alert for falling

overhead limbs. Watch your footing

while exiting area.

Figure 15 - Limbing A Tree

WARNING: Avoid kickback.

Kickback can result in severe injury

or death. See Kickback to avoid risk

of kickback.

WARNING:

• If on slope, make sure log will not

roll down hill. Secure log by us-

ing wooden stakes. Drive wooden

stakes into ground on downhill side

of log. Stand on uphill side of log

while cutting. Log may roll after

cutting.

• Never try cutting through two logs

at same time. This could increase

the risk of kickback.

• While cutting log, never hold log

with your hand, leg, or foot.

• While cutting log, never allow an-

other person to hold log.

• Turn off and unplug saw before mov-

ing from one place to another.

Bucking a log is cutting a log into sections. Make

sure your footing is ﬁrm. Keep feet apart. Divide

your weight evenly on both feet. When possible,

raise log or section off ground. Do this by using

limbs, logs, chocks, etc.

When cutting through log, maintain control by

reducing cutting pressure near end of cut. Do not

relax your grip on chain saw handles. Do not let

moving chain touch ground. Ground will dull

moving chain. After cutting through log, release

trigger to turn saw off before moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 16).

Figure 16 - Bucking Log With Entire Length

On Ground

BUCKING A LOG

OPERATING CHAIN SAW

2. Cut towards notch.

3. As felling cut nears hinge, tree should begin to fall.

Note: If needed, drive wedges into felling cut to

control direction of fall. If tree settles back and

pinches chain, drive wedges into felling cut to

remove saw. Only use wedges made of wood,

plastic, or aluminum. Never use wedge made of

steel. This could cause kickback and damage to

chain.

4. When tree begins to fall, quickly

• remove saw from felling cut

• release trigger to turn saw off

• put saw down

• exit area using retreat path

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

2" to 4"

(5 a 10 cm)

2nd Cut - Pruning

Cut (to avoid

pinching)

1st Cut - Pruning

Undercut

(to avoid splintering)

3rd Cut - Stub Undercut

(to avoid splintering)

(15 cm)

4th Cut - Final Stub

Cut

1st

Cut

2nd

Cut

1st Cut

2nd Cut

Log Supported On One End

1. Make ﬁrst cut on underside of log (see Figure

17). Use top of guide bar to make this cut. Cut

1/3 through diameter of log. This cut will keep

section from splintering when cut.

2. Make second cut directly above ﬁrst cut. Cut

down to meet ﬁrst cut. This cut will keep log

from pinching guide bar and chain.

Log Supported On Both Ends

1. Make ﬁrst cut from above log (see Figure 18).

Cut 1/3 through diameter of log. This cut will

keep section from splintering when cut.

2. Make second cut on underside of log, directly

under ﬁrst cut. Use top of guide bar to make

this cut. Cut up to meet ﬁrst cut. This will keep

log from pinching guide bar and chain.

OPERATING CHAIN SAW

TRIMMING A TREE (Pruning)

Figure 17 - Bucking Log When Log Is

Supported On One End

Figure 18 - Bucking Log When Log Is

Supported On Both Ends

CAUTION: Seek professional

help if facing conditions beyond your

ability.

WARNING: Do not cut limbs higher

than your shoulders.

WARNING: Do not operate chain

saw while

• in a tree

• on a ladder or any other unstable

surface

• in any awkward position

You may lose control of saw causing

severe injury.

Trimming a tree is the process of cutting limbs

from a living tree. Make sure your footing is ﬁrm.

Keep feet apart. Divide your weight evenly on both

feet. Follow directions below to trim a tree.

1. Make ﬁrst cut six inches from tree trunk on

underside of limb. Use top of guide bar to

make this cut. Cut 1/3 through diameter of

limb (see Figure 19).

2. Move two to four inches farther out on limb.

Make second cut from above limb. Continue

cut until you cut limb off.

3. Make third cut as close to tree trunk as possible

on underside of limb stub. Use top of guide bar

to make this cut. Cut 1/3 through diameter of

stub.

4. Make fourth cut directly above third cut. Cut

down to meet third cut. This will remove limb

stub.

Figure 19 - Cutting A Limb

WARNING: Avoid kickback.

Kickback can result in severe injury

or death. See Kickback to avoid risk

of kickback.

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

Guide Bar With Uneven Wear

Guide Bar

Normal Guide Bar

Guide Bar Groove

Oil Slot

Cleaning Groove With Putty Knife

Flat

File

Burr

Guide Bar

CARE OF GUIDE BAR

Uneven bar wear causes most guide bar problems.

Incorrect sharpening of chain cutter and depth

gauge settings often cause this. When bar wears

unevenly, it widens guide bar groove (see Figure

20). This causes chain clatter and rivet popping.

Saw will not cut straight. Replace guide bar if

this occurs.

Inspect guide bar before sharpening chain. A worn

or damaged guide bar is unsafe. A worn or damaged

guide bar will damage chain. It will also make cut-

ting harder.

CLEANING SAW BODY

CLEANING AND MAINTENANCE

WARNING: When cleaning saw

body,

• do not submerge saw in any liq-

uids

• do not use products that contain

ammonia, chlorine, or abrasives

• do not use chlorinated cleaning

solvents, carbon tetrachloride,

kerosene, or gasoline

WARNING: Unplug chain saw from

power source before servicing. Severe

injury or death could occur from electri-

cal shock or body contact with moving

chain.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

Keep saw body clean. Use a soft cloth dampened

with a mild soap and water mixture. Wipe saw body

to clean.

NOTICE: Below are instructions for

servicing your chain saw. Any ser-

vicing not mentioned below should

be done by an authorized service

center.

Normal Guide Bar Maintenance

1. Remove guide bar from chain saw.

2. Remove sawdust from guide bar groove peri-

odically. Use putty knife or wire (see Figure

21).

3. Clean oil slots after each day of use.

4. Remove burrs from sides of guide bar. Use

ﬂat ﬁle to make side edges square.

Replace guide bar when

• bar is bent or cracked

• inside groove of bar is badly worn

Note: When replacing guide bar, see Replacement

Parts and Accessories for proper bar.

WARNING: Unplug chain saw from

power source before servicing. Severe

injury or death could occur from electri-

cal shock or body contact with moving

chain.

WARNING: Cutting edges on chain

are sharp. Use protective gloves when

handling chain.

SHARPENING SAW CHAIN

Keep chain sharp. Your saw will cut faster and

more safely. A dull chain will cause undue sprock-

et, guide bar, chain, and motor wear. If you must

force chain into wood and cutting creates only

sawdust with few large chips, chain is dull.

Figure 20 - Guide Bar Cross Section Showing

Uneven Bar Wear

Figure 21 - Guide Bar Maintenance

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ENGLISH

FILE HOLDER

File Guide

Filing Direction

5/32" Round

File

30° Guide Mark

Groove

Depth Gauge (left

side of chain)

Top Plate (left

side of chain)

Right Side of Chain

Groove

Depth Gauge (right

side of chain)

Top Plate

(right side of

chain)

Figure 24 - Depth Gauge Tool On Chain

Flat File

Depth Gauge

Slot

Depth Gauge

Tool

Depth Gauge

Front Corner

.025"

.635 mm

CLEANING AND MAINTENANCE

4. Hold ﬁle guide level. Make sure 30° mark

on ﬁle guide is parallel to center of guide bar

(see Figure 22). This will insure that you ﬁle

cutters at 30° angle.

5. File from inside towards outside of cutter

until sharp. Only ﬁle in this one direction (see

Figure 22). Note: Two or three strokes with

ﬁle should sharpen cutter.

6. After each cutter is sharpened, move chain

forward to sharpen next cutter. File all cutters

on one side of chain.

7. Move to other side of chain and repeat pro-

cess.

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as

cutters are sharpened. After every second or third

sharpening, reset cutter depth gauges.

1. Place depth gauge tool (.025") ﬁrmly across

top of two cutters. Make sure depth gauge

enters slot in depth gauge tool (see Figure

24).

2. Use medium ﬂat ﬁle. File depth gauge level

with depth gauge tool.

3. Remove depth gauge tool. With ﬂat ﬁle, round

off front corner of cutter depth gauge (see

Figure 25).

After several hand ﬁlings, have authorized service

center or sharpening service machine sharpen

chain. This will insure even ﬁling.

Replacing Saw Chain

Replace chain when cutters are too worn to sharpen

or when chain breaks. Only use replacement chain

noted in this manual. Always include new drive

sprocket when replacing chain. This will maintain

proper driving of chain. Note: For proper chain

and drive sprocket, see Replacement Parts and

Accessories.

Figure 25 - Round Off Front Corner Of Depth

Gauge

Items Needed to Sharpen Chain

Purchase these items from your local dealer, hard-

ware store, or chain saw supplies outlet.

• 5/32" round ﬁle

• Depth gauge tool

• File guide

• Vise

• Medium sized ﬂat ﬁle

Sharpening Cutters

Use ﬁle guide for 30° ﬁling.

1. Adjust chain for proper tension (see Saw

Chain Tension Adjustment).

2. Clamp guide bar in vise to hold saw steady.

Note: Do not clamp chain.

3. Press 5/32" round ﬁle (attached to ﬁle guide)

into groove between top plate and depth gauge

on chain. File guide should rest on both top

plate and depth gauge (see Figure 23). Note:

File at midpoint of guide bar.

Figure 22 - File and File Guide Placement

On Chain

Note: This illustration shows ﬁle guide placement and

ﬁling direction for sharpening cutters on left side of

chain.

Figure 23 - Chain Part Locations

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ESPAÑOL

IMPORTANTE: Lea cuidadosamente este manual antes de

armar u operar esta sierra eléctrica. El uso indebido de

la misma puede provocar graves lesiones. Guarde este

manual para consultarlo cuando lo necesite.

MODELOS: M15012US, M15014AS, M30016US, M30016AS,

M30016AW, M35016AW

SIERRA ELÉCTRICA

MANUAL PARA EL USUARIO

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

EL CONTENIDO

INFORMACIÓN IMPORTANTE DE SEGURIDAD ..................................................... 25

Antes de utilizar la sierra ......................................................................................................... 25

Al utilizar la sierra .................................................................................................................... 25

Contragolpes ........................................................................................................................... 26

Mantenimiento y almacenamiento de su sierra eléctrica ........................................................ 28

DESEMBALAJE ........................................................................................................ 28

IDENTIFICACIÓN DEL PRODUCTO ......................................................................... 29

TERMINOLOGÍA ........................................................................................................ 30

GUÍA RÁPIDA DE ARRANQUE ............................................................................... 31

ENSAMBLAJE ........................................................................................................... 32

AJUSTE DE TENSIÓN DE LA CADENA SERRADA ................................................ 34

USO DE LA SIERRA ELÉCTRICA ............................................................................ 35

Lubricación .............................................................................................................................. 35

Lubricación de la cadena ........................................................................................................ 35

Remoción de restos de la tapa de la rueda dentada ............................................................... 35

Cables de prolongación ........................................................................................................... 36

Realización de cortes .............................................................................................................. 36

Tala de un árbol (Derribamiento de un árbol) .......................................................................... 37

Desmembramiento de un árbol ............................................................................................... 38

Trozado de un tronco .............................................................................................................. 39

Poda de un árbol ..................................................................................................................... 40

LIMPIEZA Y MANTENIMIENTO ................................................................................ 41

Limpieza del cabezal ............................................................................................................... 41

Cuidado de la barra de guía ....................................................................................................41

Aﬁ lado de la cadena ................................................................................................................ 42

Recambio de la cadena serrada ............................................................................................. 43

ALMACENAMIENTO ................................................................................................. 43

SERVICIO TÉCNICO ................................................................................................. 44

ACCESORIOS Y PIEZAS DE REPUESTO ............................................................... 44

SERVICIO DE REPARACIÓN ................................................................................... 44

Servicio con garantía ............................................................................................................... 44

Servicio sin garantía ................................................................................................................ 44

DIAGNÓSTICO Y RESOLUCIÓN DE PROBLEMAS ................................................ 45

INFORMACIÓN DE GARANTÍA ................................................................................ 46

DESGLOSE ILUSTRADO DE PARTES .................................................................... 72

CENTRAL DE PIEZAS .............................................................................................. 74

For parts contact: www.PartsFor.com

www.Desatech.com

www.remingtonpowertools.com

ESPAÑOL

LEA TODAS LAS INSTRUCCIONES.

Asegúrese de leer y comprender com-

pletamente todas las instrucciones en

Información Importante De Seguridad.

El uso indebido de esta sierra eléctrica

puede provocar lesiones graves (y aun

la muerte) a causa de incendio, shock

eléctrico, el contacto del cuerpo con

la cadena en movimiento o la caída de

un trozo de árbol.

INFORMACIÓN IMPORTANTE DE SEGURIDAD

ANTES DE UTILIZAR LA SIERRA

1. Lea detenidamente este manual para el usuario

antes de utilizar la sierra eléctrica.

2. Proceda con cautela. Utilice el sentido común.

No utilice la sierra cuando se sienta cansa-

do.

3. Utilice la sierra sólo para cortar madera. No la

utilice con ﬁ nes para los que no ha sido diseñada.

No la utilice para cortar plásticos, mampostería,

etc.

4. Sólo un adulto bien instruido debe utilizar la

sierra. Nunca permita que sea utilizada por

niños.

5. Utilice sólo el voltaje eléctrico indicado en la

placa del modelo de la sierra.

6. Utilice sólo cables de prolongación diseñados

para el aire libre. Consulte para conocer las

requisitos del Cable de Prolongación.

7. No utilice la sierra

• cuando se encuentre bajo la inﬂ uencia de

alcohol, medicamentos o drogas;

• bajo la lluvia o en áreas húmedas o moja-

das;

• en presencia de líquidos o gases altamente

inﬂ amables;

• cuando ésta se encuentre dañada, mal

ajustada o armada de manera incompleta e

insegura;

• si no es posible encenderla y apagarla me-

diante el gatillo. La cadena debe dejar de

moverse al soltar el gatillo. Si el interruptor

se encuentra defectuoso, hágalo reemplazar

en un centro de servicios autorizado (con-

sulte Servicio Técnico).

• cuando tenga prisa;

• cuando esté arriba de un árbol o sobre una

escalera, a menos que se encuentre capaci-

tado para hacerlo.

8. Al utilizar la sierra, lleve ropa ajustada. No

utilice ropa ni lleve accesorios sueltos, ya que

éstos pueden quedar atrapados en la cadena en

movimiento.

9. Utilice los siguientes elementos de seguridad

para utilizar la sierra eléctrica:

• guantes resistentes (utilice guantes de goma

para trabajar al aire libre);

• calzado resistente con suelas no resbaladi-

zas;

• protección ocular, tal como gafas de segu-

ridad o una pantalla facial;

• casco de seguridad;

• orejeras o tapones para los oídos;

• cubrecabellos, especialmente si tiene cabello

largo;

• máscara contra el polvo (el trabajar en zonas

polvorientas).

10.

Antes de comenzar a cortar, asegúrese de contar

con:

• zona de trabajo limpia;

• calzado ﬁ rme;

• camino de retirada para el momento de caída

del árbol.

11. Inspeccione el árbol antes de talarlo. Asegú-

rese de que no tenga ramas o vástagos secos

que puedan caerle encima.

12. Para reducir el riesgo de shock eléctrico, esta

sierra tiene un enchufe polarizado (un conector

es más ancho que el otro) y sólo entrará de una

manera en un tomacorriente polarizado. Si el

enchufe no entra completamente en el tomaco-

rriente de su cable de prolongación, inviértalo.

Si, aun así, tampoco entra, necesitará un cable

de prolongación polarizado. No altere el enchufe

de manera alguna.

AL UTILIZAR LA SIERRA

1. Permanezca alerta. Utilice el sentido común.

2. Mantenga limpia el área de trabajo. Las áreas

de trabajo sucias pueden provocar lesiones.

3. Tenga en cuenta la posición del cable de pro-

longación. Asegúrese de no tropezar sobre él.

Manténgalo alejado de la sierra y del operario en

todo momento.

4. Mantenga a los niños, animales y observadores

alejados de la sierra y del cable de prolon-

gación. Sólo el operario de la sierra debe

permanecer en el área de trabajo.

5. No proceda a talar un árbol a menos que esté

entrenado o que disponga de un asistente con

experiencia.

ADVERTENCIA: Al utilizar una sie-

rra eléctrica, deben seguirse siempre

las precauciones de seguridad básicas

para reducir el riesgo de incendios,

choque eléctrico y lesiones a perso-

nas, incluyendo las siguientes:

For parts contact: www.PartsFor.com

www.Desatech.com

La page charge ...

Desa Tech M30016AW Le manuel du propriétaire

Marque: Desa Tech

Modèle: M30016AW

Catégorie: Tronçonneuses électriques

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Desa Tech M30016AW Owner's manual
español: Desa Tech M30016AW El manual del propietario

Documents connexes

Desa Tech M30016US Le manuel du propriétaire

Desa Tech M30016AW Le manuel du propriétaire

Desa Tech M30016AW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents