Maytag MDE18CSAY Installation Instructions Manual

Marque: Maytag

Modèle: MDE18CSAY

Taper: Installation Instructions Manual

STALLATI

COMMERCIAL

I CTI

DRYERGAS OR ELECTRIC

MODELS M DG 18CSAW/M NAW/PDAW/PDAX/PRAW

M D E18M NAY/M NAZ/CSAY/CSAZ/PDAY/PDAZ/PRAY/PRAZ

I UCTI S I

SECHEUSE A USAGE COMMERCIAL ,_ GAZ OU ELECTRIQUE

M ODELES MDG18CSAW/M NAW/PDAW/PDAX/PRAW

MDE18M NAY/M NAZ/CSAY/CSAZ/PDAY/PDAZ/PRAY/PRAZ

TABLE OF CONTENTS

Page

Dryer Safety ..........................................................................................................2

Tools & Parts .......................................................................................................5

Dimensions/Ciea rances ..............................................................................6

Gas Dryer Installation Requirements ...................................................7

Electric Dryer Installation Requirements .........................................10

Dryer Venting Requirements ..................................................................13

Gas Supply Connection ............................................................................15

Installing Leveling Legs, Coin Slide, and Coin Box .....................17

Electric Dryer Electrical Connections ................................................18

Leveling ..............................................................................................................22

Complete installation ..................................................................................23

Reversing Dryer Door Swing ...................................................................24

Changing to a 30=or 60-Minute Timing Cam .................................25

Maintenance instructions .........................................................................26

if You Need Assistance ..............................................................................26

Electronic Control Setup instructions ...............................................27

TABLE DES MATII_RES

Page

S_curit_ de la s_cheuse ..........................................................................32

Outils et pieces ...........................................................................................35

Dimensions/Distances de d_gagement ........................................36

Exigences d'installation pour la s_cheuse a gaz ........................37

Exigences d'installation pour

la s_cheuse _lectrique ...........................................................................40

Exigences concernant r_vacuation

de la s_cheuse ............................................................................................42

Raccordement a la canalisation de gaz .........................................44

Installation des pieds de nivellement, de la glissiere

monnaie et de la caisse a monnaie ..............................................46

Nivellement .....................................................................................................47

Achever I'installation ..................................................................................48

inversion du sens d'ouverture de la porte ......................................49

Installation d'une came de minutage

de 30 ou 60 minutes ..................................................................................50

instructions d'entretien .............................................................................51

Si vous avez besoin d'assistance .......................................................51

Instructions de r_glage du tableau

de commande _lectronique ..................................................................52

W10474273A

W10474274A - SP www.maytagcommerciallaundry.com

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This isthe safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions,

You can be killed or seriously injured if you don't follow

instructions,

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

N|NG - ...i.kof

- Clothes dryer installation must be performed by a qualified installer.

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. If flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers, Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

[] It is recommended that the owner post, in a prominent location, instructions for the customer's use in the event the customer smells

gas. This information should be obtained from your gas supplier.

[] Post the following warning in a prominent location.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

DRYER SAFETY

WARNING: For your safety, the information in this manual must be followed to minimize !

the risk of fire or explosion, or to prevent property damage, personal injury, or death. J

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

= Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

e Clear the room, building, or area of all occupants.

= Immediately carl your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

= if you cannot reach your gas supplier, call the fire department.

- installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

in the State of Massachusetts, the following installation instructionsapply:

[] installationsand repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

iMPORTANT: When discarding or storing your old clothes dryer, remove the door.

DRYER SAFETY

IM PORTANTSAFETY iNSTRUCTiONS

WAR a JNG: To reduce the riskof fire,electricshock, or injuryto persons when using the dryer,follow basic precautions,

includingthe following:

[] Read all instructions before using the dryer.

[] This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

[] WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear the

area. Contact the dryer owner immediately.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-cleaning

solvents, other flammable, or explosive substances as they

give off vapors that could ignite or explode.

[] Do not dry unwashed items in the dryer.

[] Do not alJow chiJdren to play on or in the dryer. Close

supervision of children is necessary when the dryer is used

near chiJdren.

[] Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not open door while dryer is in operation. It will stop.

[] Do not install or store the dryer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Clean dryer lint screen before or after each load.

[] Do not use this dryer without the lint screen in place.

[] Do not repair or replace any part of the dryer or attempt any

servicing unless specificaJJy recommended in this InstaJJation

Instructions or in published user-repair instructions that you

understand and have the skills to carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] The final part of a tumble dryer cycle occurs without heat

(cooFdown cycle) to ensure that the articles are left at a

temperature that ensures that the items will not be damaged.

[] WARNING: Never stop a tumble dryer before the end of

the drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated. (Avoids risk of

spontaneous combustion).

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and dryer exhaust vent should be

cJeaned periodically by quaJified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVETHESE iNSTRUCTiONS

TOOLS & PARTS

Tools Needed:

8" (203 ram)

or 10" (254 ram)

Pipe Wrench

Torx _÷T-20 Security

Screwdriver or Bit

Level

8" (203 ram) or 10" (254 ram)

Adjustable Wrench

that opens to 1" (25 ram)

Flat-Blade Screwdriver

Phillips Screwdriver

t" (25 ram) Hex-Head

Socket Wrench

5/16" (8 ram) Socket Wrench

Pliers (that open to

19/16"[39 ram])

Utility Knife

1/4" (6 ram) Nut Driver 27" (686 ram)

Wood Block

Caulk Gun and Caulk Vent Clamps

(for installing new exhaust vent)

Pipe-Joint Compound

Suitable for Gas Type

Putty Knife

Flashlight (optional)

1" (25 ram)

Open-End Wrenches

Ruler or Measuring Tape

Parts Supplied:

Foot Boots (4)

Leveling Legs (4) Bezel Kit (PR models only)

Security Cone

(PD models only)

5/1 6" Hex Head -

18 x 21/2" Security Bolt

(PD models only)

3-Pin 60-Minute Timing Cam

(CS models only)

6-Pin 30-Minute Timing Cam

(CS models only)

t@ TORX is a registered trademark of Saturn Fasteners, Inc.

DIMENSIONS/CLEARANCES

Dimensions

Side View Back View

Clearances

35"

(889 mm)

1 "

(25 ram)

201/4"

.,_---- (743 mm )---------p.

251/2, ------_-

(648 mm)

, 81/4''

101/4''

(260 ram)

(210 ram)

31/4"

(83 mm)

27" -----------_4

¢___I (686 ram)

i Eloctric-+

_- 13_

(343ram) I

_-11"-_

(279 ram)

11/2"

(:38 mm) -_ !-.,1-

4" dia

! | (102 ram)

* 13. -*

-_1 (330ram)r _- 31/4"

(33ram)

e,e_,_;_e,s)/1048ram)

37"

(940 ram)

(gas models'

Bottom Exhaust

7 II

(178 ram)

o o

141/8''

(359 ram)

15"

(381 mm)

0 II

(0 mm)--,

Recessed Front View

1°

0 II

(0 mm)

I ml

(25 mm) --_

Closet Side View

14"

-_- (356 mm)

GAS DRYER iNSTALLATiON REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in a garage.

Failure to do so can result in death, explosion, or fire,

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements_'

[] A level floor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft floor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Gas dryer installation clearances

[] The location must be large enough to allow the dryer door

to be fully opened.

[] Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180 °.

[] Additional clearances might be required for wall, door, and floor

moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer

is recommended to reduce noise transfer.

When installing a gas dryer:

IM PORTANT: Observe all governing codes and ordinances.

[] Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

[] Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

"Recessed Area and Closet Installation Instructions" below for

minimum spacing requirements.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances:'

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. Louvered doors with equivalent air

openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same closet

as the dryer.

48 in. 2

(310 cm 2)

Front

View

24 in.2

(155 cm 2)

Closet

Door

(76 m_

GAS DRYER INSTALLATION REQUIREMENTS

Electrical Requirements

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter,

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

iMPORTANT: The dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended that

a qualified electrical installer determine that the ground path is

adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

[] Do not ground to a gas pipe.

[] Do not have a fuse in the neutral or ground circuit.

[] A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this dryer be provided.

[] This dryer is equipped with a power supply cord having a

3-prong grounding plug.

[] To minimize the possibility of shock, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of

the customer to have the properly grounded outlet installed by

a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

[] Check with a qualified electrician if you are not sure the dryer is

properly grounded.

Gas Dryer Grounding

GROUNDING INSTRUCTIONS

m For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS DRYER iNSTALLATiON REQUIREMENTS

Gas Supply

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut=off valve,

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

M PORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with

American National Standard, National Fuel Gas Code ANSi

Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this dryer has been certified by CSA International

for use at altitudes up to 10,000 feet (3048 m) above sea level at

the B.T.U. rating indicated on the model/serial plate. Burner input

adjustments are not required when the dryer is operated up to this

elevation.

When installed above 10,000 feet (3048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3048 m) elevation, contact your local service

company.

ELECTRIC DRYER iNSTALLATION REQUIREMENTS

Location Requirements

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not instafl in a garage.

Failure to do so can result in death, explosion, or fire.

Your dryer can be installed in a basement, laundry room, or

recessed area.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the dryer where it will be

exposed to the weather. Proper installation is your responsibility.

You will need:

[] A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the dryer.

See "Electrical Requirements:'

[] A level floor with a maximum slope of 1" (25 mm) under entire

dryer. Installing the dryer on soft floor surfaces, such as carpets

or surfaces with foam backing, is not recommended.

Electric dryer installation clearances

[] The location must be large enough to allow the dryer door to be

fully opened.

[] Additional spacing should be considered for ease of installation

and servicing. The door opens more than 180 °.

[] Additional clearances might be required for wall, door, and floor

moldings.

[] Additional spacing of 1" (25 mm) on all sides of the dryer is

recommended to reduce noise transfer.

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. For

recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer

or in "Dimensions/Clearances_'

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

If closet door is installed, the minimum unobstructed air opening in

the top and bottom is required. Louvered doors with equivalent air

openings are acceptable.

The dryer must be exhausted outdoors.

48 in.2

(310 cm 2}

Front

View

24 in.2

(155 cm 2)

(76 mr

Closet

Door

176_rlm}

Electrical Requirements = U.S.A. only

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

[]

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

Do not use an extension cord.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

ELECTRIC DRYER iNSTALLATiON REQUIREMENTS

Electrical Requirements - U.S.A. only (cont.)

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

[] This dryer is manufactured ready to install with a S-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

[] If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see "Optional S-wire connection"

section.

[]

A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through

the neutral conductor is prohibited. Grounding through the

neutral is prohibited for (1) new branch-circuit installations

and (2) areas where local codes prohibit grounding through

the neutral conductor.

Electric Dryer Grounding

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug on the power

supply cord: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

Electric Dryer Power Supply Cord

Fire Hazard

Use a new UL listed 30 amp power supply cord.

Use a UL listed strain relief,

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire} to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

[] A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or "U" shaped spade terminals with

upturned ends.

[] A UL listed strain relief.

If your outlet looks like this:

4-Wi re

Receptacle

(t 4-30R)

Then choose a 4-wire power supply cord with ring or

spade terminals and UL listed strain relief. The 4-wire

power supply cord, at least 4 ft. (1.22 m) long, must

have four 10-gauge copper wires and match a 4-wire

receptacle of NEMA Type 14-30R. The ground wire

(ground conductor) may be either green or bare.

The neutral conductor must be identified by a white

cover.

If your outlet

3-Wi re

Receptacle

(t O-30R)

looks like this:

Then choose a 3-wire power supply cord with ring

or spade terminals and UL listed strain relief. The

3-wire power supply cord, at least 4 ft. (1.22 m) long,

must have three 10-gauge copper wires and match a

3-wire receptacle of NEMA Type 10-30R.

ELECTRIC DRYER iNSTALLATiON REQUIREMENTS

Direct Wire

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

if connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with flexible metallic conduit.

All current-carrying wires must be insulated.

[] 10-gauge solid copper wire (do not use aluminum).

[] At least 5 ft. (1.52 m) long.

Electrical Requirements = Canada only

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

it is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code, C22.1 - latest

edition and all local codes. A copy of the above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

[] To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

[] This dryer is equipped with a CSA International

Certified Power Cord intended to be plugged

into a standard 14-30R wall receptacle. The cord

is 5 ft (1.52 m) in length. Be sure wall receptacle

is within reach of dryer's final location.

4-Wire

Receptacle

(14-30R)

[] Do not use an extension cord.

If you are using a replacement power supply cord, it is

recommended that you use Power Supply Cord Replacement

Part Number 9831317. For further information, please reference

the service numbers located in the "Assistance or Service"

section.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

DRYER VENTING REQUIREMENTS

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent,

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney,

wall, ceiling, attic, crawlspace, or a concealed space of a building.

Only rigid or flexible metal vent shall be used for exhausting.

(102 ram)

4" (102 ram) Heavy, Metal Exhaust Vent

[] Only a 4" (1 02 mm) heavy, metal exhaust vent and clamps may

be used.

[] Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess to avoid sagging and kinking that may result in

reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 73/4ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace plastic or metal foil vents with rigid metal or flexible

metal vents. Review "Vent System Chart" and if necessary, modify

existing vent system to achieve best drying performance.

Elbows:

[] 45 ° elbows provide better airflow than 90 ° elbows.

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

DRYER VENTING REQUIREMENTS

Vent Hoods

4" (102 ram) Diameter Exhaust Hoods

Box Hood Louvered Hood Angled Hood

Vent System Length

Exhaust hood must be at least 12" (305 mm) from the ground or

any object that may be in the path of the exhaust (such as flowers,

rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

3. Tighten hose clamp with Phillips screwdriver.

Vent System Chart (Rigid Metal Vent)

No. of Box and Angled

90° Turns Louvered Hood Hood

0 130 ft. (39.6 m) 129 ft. (39.3 m)

1 125 ft. (38.1 m) 119 ft. (36.3 m)

2 115 ft. (35.1 m) 109 ft. (33.2 m)

3 106 ft. (32.3 m) 100 ft. (30.5 m)

4 98 ft. (29.9 m) 92 ft. (28.0 m)

For vent systems not covered by the vent specification chart,

see your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See

"Recessed Area and Closet Installation Instructions" in the

"Location Requirements" sections.

A 4" (102 ram) outlet hood is preferred. However, a 21/2'' (64 mm)

outlet exhaust hood may be used. A 21/2'' (64 mm) outlet creates

greater back pressure than other hood types. For permanent

installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

Vent Collar

NOTE: Do not remove vent collar.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 ram) clamp.

5. Move dryer into final position. Do not crush or kink vent.

Make sure dryer is level.

DRYER VENTING REQUIREMENTS

If an Exhaust Hood Cannot be Used

The outside end of main vent should have a sweep elbow directed

downward.

12" rnin.

(305 rnrn)*

*Minimum clearance above any

accumulation of snow, ice, or

debris such as leaves

If main vent travels vertically through the roof, rather than through

wall, install a 180 ° sweep elbow on end of vent at least 2 fl.

(610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1/2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

Multiple Dryer Venting

A main vent can be used for venting a group of dryers. The main

vent should be sized to remove 5663 I/min. (200 CFM) of air per

dryer. Large-capacity lint screens of proper design may be used in

main vent if checked and cleaned frequently. The room where the

dryers are located should have make-up air equal to or greater than

CFM of all the dryers in the room.

Back-draft dampers are available from your distributor and should

be installed in the vent of each dryer to keep exhausted air from

returning into dryers and to keep exhaust in balance within main

vent. Unobstructed return air openings are required.

Although usually each single-load dryer should have an

unobstructed outdoor air opening of 24 in? (154 cm 2) (based

on 1 in? [6.5 cm 2] per 1,000 Btu [252 kcal]), common make-up air

openings are also acceptable. Set up common openings so

the make-up air is distributed equally to all of the dryers. Keep

in mind that the coverage area must be increased by 330/0 to

account for the use of registers or louvers over the openings.

Also, make-up air openings should not be installed near the

location where exhaust vents exit the building.

Each vent should enter the main vent at an angle pointing in

the direction of the airflow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should be

no more than 30 °.

Keep air openings free of dry cleaning fluid fumes. Fumes create

acids which, when drawn through the dryer heating units, can

damage dryers and items being dried.

A clean-out cover should be located on the main vent for periodic

cleaning of the vent system.

GAS SUPPLY CONNECTION

Make Gas Connection

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

1. Remove red cap from gas pipe on back of dryer.

2. Connect gas supply to dryer. Use a pipe thread compound

approved for the type of gas supplied. If flexible metal tubing

is used, be certain there are no kinks.

If necessary for service, open the toe panel. Use a putty knife

to press on the toe panel lock located at the center top of the

toe panel. Pull downward on the toe panel to open. Toe panel

is hinged at the bottom.

3. Open the shut-off valve in the gas supply line and make sure

the dryer has its own gas supply opened.

4. Test all connections by brushing on an approved noncorrosive

leak-detection solution. Bubbles will show a leak. Correct any

leaks found.

GAS SUPPLY CONNECTION

Type of Gas

This dryer is equipped for use with natural gas. It is design-certified

by CSA International for LP (propane and butane) gases with

appropriate conversion. No attempt shall be made to convert dryer

from gas specified on serial/rating plate for use with a different gas

without consulting the serving gas supplier. Conversion must be

done by a qualified service technician.

Gas conversion kit part numbers are listed near gas valve burner

base.

Gas Supply Line

Recommended Method

Provide a gas supply line of 1/2" (13 ram) rigid (IPS) pipe to dryer

location. Pipe joint compounds that resist action of LP gas must be

used. Do not use TEFLON °t tape. With LP gas, piping or tubing

size can be 1/2" (13 ram) minimum. Usually, LP gas suppliers

determine size and materials used in the system.

Flexible Metal Appliance Connector

It is recommended that a new flexible stainless steel gas line,

design-certified by CSA International, be used for connecting the

dryer to the gas supply line. (The gas pipe which extends through

the lower rear of the dryer is provided with 3/8" [10 mm] male pipe

thread.)

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of the

installed shut-off valve to the dryer (as shown above). The dryer

must be disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in excess of

1/2" psig (352 kg/m2).

Alternate Method

The gas supply may also be connected using 3/8" (10 mm)

approved copper or aluminum tubing. If the total length of

the supply line is more than 20 ft. (6.1 m), larger tubing will

be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off valve

installed within 6 ft. (1.8 m) of dryer in accordance with National

Fuel Gas Code, ANSI Z223.1. This valve should be located in

same room as dryer. It should be in a location that allows ease

of opening and closing. Do not block access to shut-off valve.

In Canada, an individual manual shut-off valve must be installed

in accordance with the B149 installation codes CAN/CGA

B149.1 and CAN/CGA B149.2.

NOTE: Do not kink or damage the flexible stainless steel gas line

when moving the dryer.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe fittings to

obtain an in-line connection to the dryer.

f(R_'TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

iNSTALLiNG LEVELING LEGS, COiN SLIDE, AND COiN BOX

On some models: The console houses the electronic control

board. The board is factory set for a dry time of 45 minutes.

Consult the tech sheet found inside the dryer toe panel to reset dry

time and for other options.

The card reading mechanism is not included, but is available from

our usual industry sources.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

On some models: The meter case houses the factory-installed

accumulator timer with actuating arm or service switch.

The factory-installed timer is set to provide 45 minutes (4 pins)

of drying time when activated by the coin slide. Timer cams

for 30-minute (6 pins) and 60-minute (3 pins) drying times are

included in the parts bag.

The coin slide mechanism, service door lock and key, and coin box

lock and key may not be included but are available from the usual

industry sources.

1. Install coin slide and coin box

Remove the service door of the meter case by lifting it up at the

back. Install the money-accepting device. (Refer to manufacturer's

instructions for proper installation.)

1. Prepare dryer for leveling legs

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging floor covering.

Using two or more people, move dryer to desired installation

location.

Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe drum interior with a damp

cloth to remove any dust.

Take two cardboard corners from the dryer carton and place them

on the floor in back of the dryer. Firmly grasp the body of the dryer

and gently lay it on its back on the cardboard corners. Disconnect

power before making electrical connections.

For dryers using coin slides, use the adapter kit supplied with the

dryer.

Replace the meter case service door. Put the coin vault with lock

and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust the legs

of the dryer up or down until the dryer is level.

2. Install added security device

Check that power is not supplied to the dryer.

Open and remove the service door.

Insert the narrow part of the security cone into the oblong hole in

the bottom rear of the meter case assembly.

Pass the security bolt through this cone and thread it by hand into

the cage nut below the oblong hole.

Tighten the security bolt by hand a few turns before using a wrench

to tighten until snug.

(appearance may var_

2. Screw in leveling legs

Examine leveling legs and find diamond

marking. Screw legs into leg holes by

hand. Use an adjustable wrench or

1" (25 mm) hex-head socket wrench

to finish turning legs until diamond

marking is no longer visible. Then fit

a covered foot boot over each leg foot.

Diamond _/_

Marking

Foot i-_

To protect the floor, use a large piece of cardboard from the dryer

carton. Stand dryer up on the cardboard. Slide the dryer until

it is close to its final location. Leave enough room for electrical

connection and to connect the exhaust vent.

Security

Bolt

Security

Cone

Cage

Nut

NOTE: Installing the security bolt provides added security, but

will add to the service time when the top needs to be removed

for servicing the dryer.

ELECTRICDRYER ELECTRICALCONNECTIONS (FORU.S.A.ONLY)

Power Supply Cord Strain Relief

1. Insert strain relief.

Strain Relief

RemoveTerminalBlock Cover

(appearance may vary)

2. Insert power cord into strain relief.

Strain Relief

Direct Wire Strain Relief

1. Insert strain relief.

2. Insert conduit into strain relief and tighten damp.

ELECTRIC DRYER ELECTRICALCONNECTIONS (FORU.S.A.ONLY)

Connection Options

Power Cord

4-wire receptacle (NEMA Type 14-30R)

(127

3-wire receptacle (NEMA Type 10-30R)

3-wire direct

Connecting 4-Wire Connection: Power Supply Cord

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire

connections.

Standard Power Supply Cord Connectors

Flanged Spade Connector Ring Connector

Connecting Neutral Ground and Neutral Wires

1. Remove center terminal block screw (A) and the neutral

ground wire (B) by removing the green external ground

conductor screw (C).

2. Connect neutral ground wire (B) and neutral wire (white or

center wire) (D) of power supply cord under center terminal

block screw (A). Tighten screw.

Connecting Direct Wire Ground

3. Connect ground wire (green or bare) (E) of power supply cord

under green external ground conductor screw (C). Tighten

screw.

Connecting Remaining Wires

4. Connect remaining wires under outer terminal block screws

(F). Tighten screws. Finally, reinstall terminal block to dryer rear

panel. Secure cover with hold-down screw.

ELECTRICDRYER ELECTRICALCONNECTIONS (FORU.S.A.ONLY)

Connecting 3-Wire Connection: Power Supply Cord

Standard Power Cord Connectors

Flanged Spade Connector Ring Connector

2. Connect neutral wire (white or center wire) (D) of power supply

cord under center terminal block screw (A). Tighten screw.

Connecting Neutral Wire

1. Loosen or remove center terminal block screw (A).

3. Connect remaining wires under outer terminal block screws

(F). Tighten screws. Finally, reinstall terminal block to dryer rear

panel. Secure cover with hold-down screw.

Connecting 4-Wire Connection: Direct Wire

iMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving bare

ground wire at 5" (127 mm). Cut 11/2" (38 mm) from 3 remaining

wires. Strip insulation back 1" (25 mm). Shape ends of wires into

a hook shape.

Connecting Neutral Ground and Neutral Wires

1. Remove center terminal block screw (A) and the neutral

ground wire (B) by removing the green external ground

conductor screw (C).

La page charge ...

Maytag MDE18CSAY Installation Instructions Manual

Marque: Maytag

Modèle: MDE18CSAY

Taper: Installation Instructions Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MDE18CSAY

Documents connexes

Autres documents

Whirlpool CET8000XQ0 Guide d'installation