Panasonic CQDFX302U - AUTO RADIO/CD DECK Operating Instructions Manual

Panasonic
Marque
Panasonic
Modèle
CQDFX302U - AUTO RADIO/CD DECK
Catégorie
Lecteur CD
Taper
Operating Instructions Manual

Ce manuel convient également à

Removable Full Front CD Player/Receiver with CD Changer Control
Lecteur CD/récepteur avec panneau avant
amovible et contrôle de changeur CD
Reproductor de CD/Receptor con Controlador de
Cambiador de CD y Frente Complete Desmontable
CQ-DF402U
Removable Full Front CD Player/Receiver
Lecteur CD/récepteur avec panneau avant amovible
Reproductor de CD/Receptor y Frente Complete Desmontable
CQ-DFX302U
VOL
S
C
A
N
/A
P
M
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
C
L
O
C
K
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET
45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/L
O
C
LEVL
REMOTE
(CQ-DF402U)
DIMMER
≥ Please read these instructions carefully before using this product and save this manual for future use.
≥ Prière de lire ces instructions attentivement avant d’utiliser Ie produit et garder ce manuel pour l’utilisation ultérieure.
≥ Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro.
Operating Instructions
Manuel d
’instructions
Manual de instrucciones
F
R
A
N
Ç
A
I
S
CQ-DF402/DFX302U
3
E
N
G
L
I
S
H
CQ-DF402/DFX302U
2
Find the model number and serial number on either
the back or bottom of the unit. Please record them
in the space below and retain this booklet as a per-
manent record of your purchase to help with identi-
fication in case of theft.
MODEL NUMBER CQ-DF402U/CQ-DFX302U
SERIAL NUMBER
DATE PURCHASED
FROM
Il est recommandé de noter, dans l’espace prévu ci-
dessous, les numéros de modèle et de série inscrits soit
à l’arrière soit sous le fond de l’appareil, et de conserver
ce manuel comme mémorandum de l’achat afin de per-
mettre l’identification de l’appareil en cas de vol.
NUMÉRO DE MODÈLE CQ-DF402U/CQ-DFX302U
NUMÉRO DE SÉRIE
DATE DE L’ACHAT
VENDEUR
Busque el número del modelo y el número de serie ya
sea en la parte trasera o en el fondo de la unidad. Sírvase
anotar dichos números en el espacio siguiente, y man-
tenga este librete como una anotación permanente de su
compra para ayudar en la identificación en el caso de
robo.
NÚMERO DEL MODELO CQ-DF402U/CQ-DFX302U
NÚMERO DE SERIE
FACHA DE COMPRA
NOMBRE DE LA TIENDA
C Q - D F 4 0 2 U
Model No.
N˚ De Modèle
Serial No.
N˚ De Série
Manufactured by Dalian Matsushita
Communication Industrial Co., Ltd.
Dalian China Made in China
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
condition that this device does not cause
harmful interference.
15A12V 4~8
FM75
D
I
S
P
3
(CQ-DF402U)
Radio Frequency Interference Statement (Part 15 of the FCC Rules):
Applies only in U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to
Part 15 of the FCC Rules.
≥ These limits are designed to provide reasonable protection against harmful interference in an automo-
bile installation. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio reception, which can be determined by
turning the equipment off and on, the user is encouraged to consult the dealer or an experience radio
technician for help.
FCC Warning:
Any unauthorized changes or modifications to this equipment would void the user’s authority to operate
this device.
This device complies with Part 15 of the FCC Rules:
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
§For Canada:
This Class B digital apparatus complies with Canadian ICES-003.
Label Indication and Location
Safety Information
Consignes de sécurité
Información para su seguridad
E
S
P
A
Ñ
O
L
CAUTION:
THIS PRODUCT IS A CLASS I LASER PROD-
UCT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR
YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, AND ANNOYING INTERFERENCE, USE
ONLY THE INCLUDED COMPONENTS.
Laser products:
Wave length: 780 nm
Laser power: No hazardous radiation is emitted
with safety protection.
ATTENTION :
CET APPAREIL EST UN PRODUIT LASER DE LA CLASSE
I.
L’UTILISATION DE COMMANDES OU RÉGLAGES OU
L’EXÉCUTION D’OPÉRATIONS AUTRES QUE CELLES
QUI SONT INDIQUÉES DANS CE DOCUMENT PEUVENT
RÉSULTER EN UNE EXPOSITION À UN RAYONNEMENT
DANGEREUX.
N’OUVREZ PAS LES COUVERCLES ET N’ESSAYEZ PAS
D’EFFECTUER VOUS-MÊME DES RÉPARATIONS.
ADRESSEZ-VOUS À UN PERSONNEL QUALIFIÉ POUR
TOUTE RÉPARATION.
MISE EN GARDE:
POUR RÉDUIRE LES RISQUES D’INCENDIE OU D’ÉLEC-
TROCUTION, N’EXPOSEZ PAS CET APPAREIL À LA
PLUIE OU À L’HUMIDITÉ.
AFIN DE PRÉVENIR TOUT RISQUE D’INCENDIE OU
D’INTERFÉRENCES, UTILISER UNIQUEMENT LES
COMPOSANTS FOURNIS.
Produits laser:
Longueur d’onde: 780 nm
Puissance du laser: Aucune radiation dangereuse
n’est émise avec la protection de
sécurité.
§Déclaration d’interférence de fréquences radio
(Partie 15 des Règlements FCC):
Cet appareil numérique de Classe B est conforme au
règlement NMB-003 canadien.
PRECAUCIÓN:
ÉSTE ES UN PRODUCTO LÁSER DE LA CLASE I.
LA UTILIZACIÓN DE CONTROLES, EL HACER
AJUSTES O EL SEGUIR PROCEDIMIENTOS DISTINTOS
DE LOS ESPECIFICADOS EN ESTE MANUAL PODRÍA
CAUSAR UNA EXPOSICIÓN PELIGROSA A LA RA-
DIACIÓN.
NO ABRA LAS CUBIERTAS NI HAGA REPARACIONES
USTED MISMO. SOLICITE LOS TRABAJOS DE SERVI-
CIO AL PERSONAL CALIFICADO.
ADVERTENCIA:
PARA REDUCIR EL RIESGO DE INCENDIOS O
SACUDIDAS ELÉCTRICAS, NO EXPONGA ESTE
PRODUCTO A LA LLUVIA NI A LA HUMEDAD.
PARA REDUCIR EL RIESGO DE INCENDIOS O SACUDI-
DAS ELÉCTRICAS, Y PARA EVITAR LAS
INTERFERENCIAS MOLESTAS, UTILICE
SOLAMENTE LOS COMPONENTES INCLUIDOS.
Productos láser:
Longitud de onda: 780 nm
Potencia láser: Con protección de seguridad no se
emite radiación peligrosa.
Models
Features
CQ-DF402U CQ-DFX302U
CD changer control Yes None
Pre-Amp output connector Lead type Fix type
F
R
A
N
Ç
A
I
S
CQ-DF402/DFX302U
5
E
N
G
L
I
S
H
CQ-DF402/DFX302U
4
E
N
G
L
I
S
H
❐ Use this Product Safely
Modèles
Caractéristiques
CQ-DF402U CQ-DFX302U
Commande de changeur de CD Oui Non
Connecteur de sortie préampli Type ligne Type fixe
Panasonic welcomes you to our ever growing family of electronic product owners. We know that this prod-
uct will bring you many hours of enjoyment. Our reputation is built on precise electronic and mechanical
engineering, manufactured with carefully selected components and assembled by people who take pride in
their work. Once you discover the quality, reliability, and value we have built into this product, you too will
be proud to be a member of our family.
When Driving
Keep the volume level low enough to be aware of
road and traffic conditions.
When Car Washing
Do not expose the product, including the speakers
and CDs, to water or excessive moisture. This
could cause electrical shorts, fire, or other damage.
When Parked
Parking in direct sunlight can produce very high
temperatures inside your car. Give the interior a
chance to cool down before switching the unit on.
Use the Proper Power Supply
This product is designed to operate with a 12 V DC,
negative ground battery system (the normal system
in a North American car).
Disc Mechanism
Do not insert coins or any small objects. Keep
screwdrivers and other metallic objects away from
the disc mechanism and disc.
Use Authorized Servicenters
Do not attempt to disassemble or adjust this preci-
sion product. Please refer to the Servicenter list in-
cluding with this product for service assistance.
For Installation
This product should be installed in a horizontal po-
sition with the front end up at a convenient angle,
but not more than 30x.
Note:
≥This operating instruction manual is for 2 models CQ-DF402U and CQ-DFX302U. All illustrations through-
out this manual represent model CQ-DF402U unless otherwise specified. The following table describes the
differences between 2 models.
≥ Operating instructions .................................... 1
≥ Installation hardware................1 set (➡ page 19)
≥ Power connector ............................................ 1
≥ Remote control unit ........................................ 1
≥ Lithium battery (CR2025)................................ 1
≥ Warranty card.................................................. 1
❐ Components
Panasonic est heureuse de vous compter parmi les utilisateurs de ses appareils électroniques. Nous pouvons vous as-
surer que cet appareil vous procurera de longues heures d’agrément. Notre réputation est fondée sur une ingénierie
électronique et mécanique de haute précision, laquelle préside à la fabrication d’appareils ne comportant que des com-
posants de choix assemblés par un personnel soucieux de la bonne réputation acquise par la qualité de son travail.
Après avoir découvert la qualité, la valeur et la fiabilité de cet appareil, vous aussi serez fier d’être un client Panasonic.
Mécanisme de disque
N’insérez pas de pièces de monnaie ou de petits objets.
Gardez les tournevis et autres objets métalliques à l’écart
du mécanisme de disque et du disque.
Réparation
Ne tentez pas de démonter ou d’ajuster l’appareil vous-
même. Veuillez vous référer à la liste des centres de ser-
vice fournie avec cet appareil pour contacter le service
d’assistance.
Installation
L’appareil doit être installé en position horizontale avec
son extrémité avant inclinée vers le haut à un angle com-
mode, mais ne dépassant pas 30x.
Au volant
Réglez le volume à un niveau qui ne risque pas de mas-
quer les bruits ambiants.
Lavage de la voiture
Afin de prévenir tout risque de court-circuit ou d’in-
cendie, n’exposez pas l’équipement, y compris les haut-
parleurs et les disques, à l’eau ou à une humidité
excessive.
Voiture stationnée
L’habitacle d’une voiture immobile exposée au soleil
toutes vitres fermées devient rapidement très chaud.
Laisser rafraîchir l’intérieur du véhicule avant d’utiliser
l’appareil.
Source d’alimentation
Cet appareil est conçu pour fonctionner sur un système
d’alimentation avec batterie de 12 V c.c. à masse
négative (système standard sur les voitures de construc-
tion nord-américaine).
❐ Précautions à prendre
≥ Manuel d’instructions.............................................. 1
≥ Quincaillerie pour l’installation
..............................................1 ensemble (➡ page 41)
≥ Connecteur d’alimentation ...................................... 1
≥ Télécommande........................................................ 1
≥ Pile au lithium (CR2025) ........................................ 1
≥ Carte de garantie .................................................... 1
❐ Éléments constitutifs
Remarque:
≥ Ce manuel a été conçu pour les 2 modèles CQ-DF402U et CQ-DFX302U. Toutes les illustrations du présent manuel
mettent en présence le modèle CQ-DF402U à moins d’indication contraire. Le tableau ci-dessous décrit les
différences entre les 2 modèles.
NOTICE:
❐ Language for Manuals of Products Using LCD
This product has a fluorescent lamp that contains a small amount of mercury. It also contains lead in some
components. Disposal of these materials may be regulated in your community due to environmental con-
siderations. For disposal or recycling information please contact your local authorities, or the Electronics
Industries Alliance: <http://www.eiae.org.>
E
N
G
L
I
S
H
CQ-DF402/DFX302U
7
Contents
E
S
P
A
Ñ
O
L
CQ-DF402/DFX302U
6
Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Radio Frequency Interference Statement (Part 15 of the FCC Rules). . . . . 12
Use this Product Safely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Language for Manuals of Products Using LCD . . . . . . . . . . . . . . . . . . . . . . 4
❒ Power and Sound Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
How to adjust the volume, tone and balance, setting mute ,
setting/resetting the time, selecting the clock display
❒ Radio Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Manual and automatic tuning, band selection, preset stations
❒ CD Player and CD Changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Disc insert and playback, stop and disc eject, CD play, track selection,
search, repeat, random, scan and direct track/disc selection
Note:
≥ The CD changer functions are designed for Panasonic CD changer unit
(optional).
❒ Remote Control Unit Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Battery installation, battery notes, control reference guide
❒ Installation Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Step-by-step procedures
❒ Anti-Theft System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Place the removable face plate into case, install removable face plate,
security indicator
❒ Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cautions and wiring diagram
❒ Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Where to get service help, troubleshooting tips, error display messages
❒ Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Care of the unit, notes on CD/CD media (CD-R, CD-RW), notes on CD-
Rs/RWs
❒ Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
FM
Panasonic le da la bienvenida a la familia constantemente en aumento de poseedores de productos electrónicos. Nos
esforzamos en proporcionarle las ventajas de la ingeniería mecánica y electrónica de precisión, de una fabricación con
componentes cuidadosamente seleccionados, y de un montaje realizado por personas orgullosas de la reputación que
su trabajo ha cimentado para nuestra empresa. Estamos seguros de que este producto le proporcionará muchas horas
de distracción y, una vez comprobada la calidad, el valor y la fiabilidad incorporados, usted también se sentirá orgul-
loso de pertenecer a nuestra familia.
Cuando conduzca
Mantenga el nivel del volumen suficientemente bajo para
estar atento a la carretera y a las condiciones del tráfico.
Cuando lave el automóvil
No exponga el equipo, incluyendo los altavoces y los
CDs, al agua o a una humedad excesiva. Esto puede
causar cortocircuitos eléctricos, incendios u otros daños.
Cuando esté estacionado
El estacionamiento a la luz solar directa puede producir
temperaturas muy altas en el interior de su vehículo.
Procure enfriar el interior antes de encender la unidad.
Uso de la alimentación apropiada
Este equipo ha sido diseñado para funcionar con un sis-
tema de batería de 12 V CC con negativo a masa (el sis-
tema normal en un vehículo norteamericano).
Mecanismo de disco
No inserte monedas ni ningún objeto pequeño. Mantenga
los destornilladores u otros objetos metálicos apartados
del mecanismo de disco y del disco.
Uso de los centros de servicio autoriza-
dos
No intente desmontar ni ajustar este equipo de precisión.
Consulte la lista de centros de servicio incluidos con este
producto para acudir a ellos cuando sea necesario.
Instalación
La unidad deberá instalarse en posición horizontal, con el
extremo delantero hacia arriba formando un ángulo con-
veniente, pero con no más de 30x.
❐ Uso de este equipo con seguridad
≥ Manual de instrucciones.......................................... 1
≥ Accesorios suministrados ........1 juego (➡ página 63)
≥ Conector de alimentación........................................ 1
≥ Unidad del controlador remoto................................ 1
≥ Pila de litio (CR2025).............................................. 1
≥ Tarjeta de garantía .................................................. 1
❐ Componentes
Nota:
≥ Este manual de instrucciones de operación serve para 2 modelos CQ-DF402U y CQ-DFX302U. Todas las ilustraciones
de este manual representan el modelo CQ-DF402U, a menos que se especifique lo contrario. La tabla siguiente mues-
tra las diferencias entre los 2 modelos.
Modelo
Características
CQ-DF402U CQ-DFX302U
Control de cambiador de CD Sí Ninguna
Conector de salida del preamplificador Tipo cable conector Tipo fijo
E
N
G
L
I
S
H
2
CQ-DF402/DFX302U
11
E
N
G
L
I
S
H
1
CQ-DF402/DFX302U
10
Power and Sound Controls
Power
Turn the key in the ignition until the accessory indi-
cator lights.
Power on: Press [SOURCE] (PWR).
Power off: Press [SOURCE] (PWR) again and hold.
Mute
Press [
MUTE
] to mute the sound completely.
Press [
MUTE
] again to cancel.
Note:
≥ When the power is switched on for the first time,
a demonstration message appears on the display.
To cancel this display, press [DISP].
Volume
[" VOL]: Up
[# VOL]: Down
Press and hold for rapid adjustment.
Volume level
(0 to 40)
Anti-volume-blast circuit:
When the power is switched off and on again, the volume slowly rises to the previous level.
The anti-volume-blast circuit will not work when the volume level is set lower than position 20 on the dis-
play.
VOL
SCAN
/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
REMOTE
DIMMER
ACC
O
N
Loudness
Press [LOUD] to enhance bass and treble tones
at low or medium volume.
Press [LOUD] again to cancel.
Dimmer
Press and hold [LEVL] (DIMMER) for more than
2 seconds to change the dimmer level.
Level Meter
When the power is on, the level of sound sources,
such as radio and CD, is displayed.
Press [LEVL] to change the level meter display.
VOL
SCAN
/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
REMOTE
DIMMER
Dimmer 1 Dimmer 2 Dimmer 3
(Bright) (Medium) (Dark)
(Default)
LOUD
E
N
G
L
I
S
H
4
CQ-DF402/DFX302U
13
E
N
G
L
I
S
H
3
CQ-DF402/DFX302U
12
Power and Sound Controls
(Continued)
VOL
SCAN/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
REMOTE
DIMMER
Audio Mode (Bass/Treble/Balance/Fader/Subwoofer)
Regular Mode
Volume Bass Treble
BalanceFaderSubwoofer
Subwoofer volume:
Bass:
Adjustable range: j12 dB to i12 dB
Treble:
Adjustable range: j12 dB to i12 dB
Balance:
R (right speaker) or L (left speaker)
Fader:
F (front speaker) or R (rear speaker)
Adjustable range: 1 to 15 Balance center
Adjustable range: 1 to 15 Fader center
Subwoofer volume level:
From MUTE (0) to 8
Default
Initial Time
1 Press [DISP] (CLOCK).
Hours
2 Press and hold [DISP] (CLOCK).
3 Press [% TUNE] or [$ TUNE].
Minutes
4 Press [DISP] (CLOCK).
5 Press [% TUNE] or [$ TUNE].
6 Press [DISP] (CLOCK).
Note:
≥ Press and hold [% TUNE] or [$ TUNE] to change
numbers rapidly.
Time Reset
Press and hold [DISP] (CLOCK) for more than
2 seconds to activate the time setting mode to reset
the time.
Then, repeat steps
3
to
6
.
Clock Display
Press [DISP] (CLOCK) to switch to the clock dis-
play.
Broadcast station
Clock display
Playing time Clock display
In CD player (changer) mode:
In tuner mode:
When the power is off:
No displayClock display
(Hours blink.)
(Hours set.)
(Minutes blink.)
(Minutes set.)
(End.)
Note:
≥ The [DISP] (CLOCK) button will not work while
the CD player or CD changer is set to the scan
play mode. Cancel the scan play mode before
pressing [DISP] (CLOCK).
The 12-hour system is used for the clock.
VOL
SCAN/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
REMOTE
DIMMER
Clock Basics
Press [SEL] to select the audio mode.
1 Note:
≥ If no operation takes place for more than
5 seconds in audio mode (2 seconds in vol-
ume mode), the display returns to the regu-
lar mode.
Press [" VOL] or [# VOL] to change each
level.
2
E
N
G
L
I
S
H
6
CQ-DF402/DFX302U
15
E
N
G
L
I
S
H
5
CQ-DF402/DFX302U
14
Radio Basics
VOL
SCA
N/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
REMOTE
DIMMER
Up to 6 stations each can be saved in the FM1,
FM2, FM3 and AM preset station memories.
Tuning in a Preset Station
Press the corresponding preset button [1]
to [6] to tune in a preset station.
Note:
≥ You can change the memory presetting by re-
peating the above procedure.
Caution:
≥ To ensure safety, never attempt to preset sta-
tions while you are driving.
Preset number
3
Manual Station Preset
1 Use manual or seek tuning to find a
station. (➡ page 14)
2 Press and hold one of the preset but-
tons from [1] to [6] until the display
blinks once.
Preset Station Setting
Radio
CD player
CD changer control
(When a CD is inserted.)
(When a CD changer is connected.)
Only for CQ-DF402U
Source
VOL
SCAN/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET 45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
M
O
N
O
/LO
C
LEVL
ST
REMOTE
DIMMER
FM stereo indicator
MONO
LOCAL
MONO
LOCAL
LOCAL
MONO OFF/
LOCAL OFF
MONO ON/
LOCAL OFF
MONO ON/
LOCAL ON
MONO OFF/
LOCAL ON
LOCAL OFF
LOCAL ON
FM broadcast:
AM broadcast:
Seek Tuning
Press and hold ...
[$ TUNE]: Higher frequency
[% TUNE]: Lower frequency
Tuning will automatically stop when the signals
of the next broadcast station are received.
Band
Press [BAND] to change the band.
2
Mode Selection
Press [SOURCE] to change to the radio mode.
1
Manual Tuning
[$ TUNE]: Higher frequency
[% TUNE]: Lower frequency
3
Mono/Local Selection
MONO: Noise is significantly decreased when
weak signals are received from an FM
broadcast station.
LOCAL: Only strong signals of stations are
searched in seek tuning, while at the
LOCAL OFF setting, relatively weak sig-
nals are also searched.
FM broadcast:
Press and hold [MUTE] (MONO/LOC) to change
the mode.
Release at the desired mode.
AM broadcast:
Press and hold [MUTE] (MONO/LOC) to switch
LOCAL mode on and off.
4
Band
Press [BAND] to select a desired band.
(➡ page 14)
Auto Station Preset
Press and hold [BAND] (APM) for more
than 2 seconds (auto preset memory).
≥ The 6 strongest available stations will be
automatically saved in the memory
under preset buttons [1] to [6].
≥ Once set, the preset stations are se-
quentially scanned for 5 seconds each.
Note:
≥ The stations manually preset on the se-
lected band will be deleted.
2
1
SOURCE
REP
MOSFET
45W
X
4
RANDOM
OPEN
PWR
RAND
E
N
G
L
I
S
H
8
CQ-DF402/DFX302U
17
E
N
G
L
I
S
H
7
CQ-DF402/DFX302U
16
CD Player and CD Changer
Track random play
≥ Press and hold [REP] (RANDOM) for
more than 2 seconds.
All the tracks (on all discs in the maga-
zine*) are played in random order.
(*Only for CD changer)
≥ Press and hold [REP] (RANDOM) again
to cancel.
Track scan play
Disc scan play
≥ Press [BAND] (SCAN).
The first 10 seconds of each track on
the disc are played in sequence.
≥ Press [BAND] (SCAN) again to cancel.
Track repeat play
≥ Press [REP].
The current track is repeated.
≥ Press [REP] again to cancel.
≥ Press and hold [BAND] (SCAN) for
more than 2 seconds.
The first track of all the discs in the
magazine is played for 10 seconds
each.
≥ Press and hold [BAND] (SCAN) again to
cancel.
CD
player
CD
changer
CD
player
CD
changer
CD
changer
CD
player
CD
changer
Direct Track Selection
≥ Press a track number button from [1] to
[6].
The corresponding track starts playing.
≥ Press and hold a track number button from
[7] to [12] ([1] to [6]) for more than 1 sec-
ond.
The corresponding track starts playing.
Direct Disc Selection
≥ Press a disc number button from [1] to [6].
The corresponding disc starts playing.
≥ Press and hold a disc number button from [7] to
[12] ([1] to [6]) for more than 1 second.
The corresponding disc starts playing.
VOL
S
C
A
N
/A
P
M
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET
45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
MONO/LO
C
LEVL
REMOTE
DIMMER
REP
Track scan play
Disc scan play
Track random play
Track repeat play
Lights when the disc
is loaded.
Note:
≥ The CD changer functions are designed for Panasonic CD changer unit (optional).
≥ This unit does not support CD-ROM, CD-R, or CD-RW playback through CD changer. Use the CD changer to
listen to normal music CDs exclusively.
Display Change
Press [DISP] to switch to the clock display.
Radio
CD player
CD changer control
(When a CD is inserted.)
(When a CD changer is
connected.)
Only for CQ-DF402U
Source
Mode Selection
Press [SOURCE] to change to the CD player or
CD changer mode.
Track number/Track playing time Clock display
Listening to a CD
Disc number/Track number/ Clock display
Track playing time
CD player:
CD changer:
Track Selection
[5TRACK]: Advance to the next track.
[6TRACK]: Back to the beginning of the cur-
rent track.
Back to the previous track.
(Press twice.)
Track Search
Press and hold ...
[5TRACK]: Fast forward
[6TRACK]: Fast backward
Release to resume the regular CD or CD changer
play.
<
(EJECT)
Press [<] (EJECT) to stop CD play and eject the disc.
When CD is in the player
Press [SOURCE] to change to CD play mode.
Cautions:
≥ Only 12 cm CD, CD-DA data recorded CD-R and CD-RW discs are available for this unit.
≥ This unit does not support CD text display.
≥ This unit does not support MP3 disc playback.
≥ Refer to page 30 about notes on CD-Rs/RWs.
≥ This unit is not designed for any 8 cm CD.
≥ If you insert an 8 cm CD and can not eject it, turn ACC of your car off once and turn it on again, then
press [<] (EJECT).
Label side
Close
VOL
SCAN/APM
SEL
BAND
TUNE
MUTE DISP
12
34
5
6
712
CLOCK
SOURCE
REP
CQ-DF402U
CD RECEIVER WITH CHANGER CONTROL
MOSFET
45W
X
4
RANDOM
OPEN
PWR
811
910
TRACK
LOUD
MONO/LOC
LEVL
REMOTE
DIMMER
Lights when a magazine is
loaded in the changer.
Disc Insert and Playback
Stop and Disc Eject
Open the front panel.
Press [OPEN] to open the front panel.
Insert the disc.
Playback will start automatically after the unit recognized the
loaded disc as an ordinary music CD. (When a CD-R or CD-RW
which has CD-DA formatted data as the same as an ordinary
CD is loaded, this unit recognizes it as an ordinary music CD.)
Close the front panel manually.
CD
player
CD
changer
CD
changer
1
2
Only for CQ-DF402U
E
N
G
L
I
S
H
10
CQ-DF402/DFX302U
19
Installation Guide
E
N
G
L
I
S
H
9
CQ-DF402/DFX302U
18
Remote Control Unit Preparation
Battery Installation
1 Remove the battery holder.
Pull the holder by the position B while pushing posi-
tion A in the direction indicated by the arrow.
2 Install the battery on the battery holder.
Set a new battery properly with its (i) side facing up
as shown in the figure.
3 Insert the battery holder.
Push in the battery holder back into its original posi-
tion.
Battery Notes
Remove and dispose of an old battery immediately.
Battery Information:
≥ Battery type: Panasonic lithium battery (CR2025) (included)
≥ Battery life: Approximately 6 months with normal use (at room temperature)
Back side
Lithium battery
(included)
Battery holder Position A
Position B
≥ Do not disassemble or short the battery. Do not throw a battery into a fire.
≥ Keep batteries away from children to avoid the risk of accidents.
≥ Be careful to the local disposal rules when you dispose of batteries.
Control Reference Guide
Buttons of the remote control function in the same way as the controls on the main unit of the reference page.
Point the remote control unit at the main unit’s sensor (REMOTE).
Mute button (MUTE)
(➡ page 10)
Volume control buttons
(VOL, " #)
(➡ page 10)
Tune/Track buttons
(TUNE/TRACK, 65/% $)
(➡ pages 14, 16)
Power button (PWR)
(➡ page 10)
Mode button (MODE)
(➡ pages 14, 16)
Caution:
≥ Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire.
Battery leakage may damage the unit.
PWR
MODE
PRG
TUNE
TRACK
Car Audio
BAND/DISC UP
VOL
MUTE
(ATT)
Band/Disc up* button
(BAND/DISC UP*)
(➡ pages 14, 17)
*Only for CD changer
control
(When the CD changer
is connected.)
1
1
1
1
1
1
1
1
No. Item Diagram Q’ty
WARNING
This installation information is designed for experienced installers and is not in-
tended for non-technical individuals. It does not contain warnings or cautions of po-
tential dangers involved in attempting to install this product.
Any attempt to install this product in a motor car by anyone other than qualified in-
staller could cause damage to the electrical system and could result in serious per-
sonal injury or death.
❐ Installation Hardware
If you encounter problems, please consult your
nearest professional installer.
6
7
8
Mounting collar
Hex. nut (5 mm·)
Rear support strap
Tapping screw
(5 mm·a16 mm)
Mounting bolt (5 mm·)
Power connector
Removable face plate
case
Trim plate
1
2
3
4
5
❐ Overview
12 V DC
Test bulb
Electrical
tape
Side-cut
pliers
❐ Required Tools
You’ll need a screwdriver, a 1.5 V AA battery, and
the following:
❐ Dashboard Specifications
Thickness
Min.
3
⁄16z (4.75 mm)
Max.
7
⁄
32
z (5.56 mm)
2
3
⁄
32
z (53 mm)
7
5
⁄32z (182 mm)
This product should be installed by a professional.
However, if you plan to install this product yourself,
your first step is to decide where to install it. The
instructions in these pages will guide you through
the remaining steps:
(Please refer to the “WARNING” statement
above.)
≥ Identify and label the car wires.
≥ Connect the car wires to the wires of the power
connector.
≥ Install the unit in the dashboard.
≥ Check the operation of the unit.
Caution:
≥ This unit operates with a 12 V DC negative
ground auto battery system only. Do not at-
tempt to use it in any other system. Doing so
could cause serious damage.
Before you begin installation, look for the items
which are packed with your unit.
≥ Warranty Card…Fill this out promptly.
≥ Panasonic Servicenter for Service Directory
…Keep for future reference in case the product
needs servicing.
≥ Installation Hardware…Needed for in-dash in-
stallation.
E
N
G
L
I
S
H
12
CQ-DF402/DFX302U
21
E
N
G
L
I
S
H
11
CQ-DF402/DFX302U
20
Installation Guide (Continued)
The first step in installation is to identify all the car
wires you’ll use when hooking up your sound sys-
tem.
As you identify each wire, we suggest that you label
it using masking tape and a permanent marker.
This will help avoid confusion when making con-
nections later.
Note:
≥ Do not connect the power connector to the stereo
unit until you have made all connections. If there
are no plastic caps on the stereo hooking wires,
insulate all exposed leads with electrical tape until
you are ready to use them. Identify the leads in
the following order.
Power Lead
If your car has a radio or is pre-wired for one:
Cut the connector wires one at a time from the plug
(leaving the leads as long as possible) so that you
can work with individual leads.
❐ Identify All Leads
Turn the ignition on to the accessory position, and
ground one lead of the test bulb to the chassis.
Touch the other lead of the test bulb to each of the
exposed wires from the cut radio connector plug.
Touch one wire at a time until you find the outlet
that causes the test bulb to light.
Now turn the ignition off and then on. If the bulb
also turns off and on, that outlet is the car power
lead.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for radio
(RADIO), accessory (ACC), or ignition (IGN).
Battery Lead
If your stereo unit has a yellow lead, you will need
to locate the car’s battery lead. Otherwise you may
ignore this procedure. (The yellow battery lead pro-
vides continuous power to maintain a clock, memo-
ry storage, or other function.)
If your car has a radio or is pre-wired for one:
With the ignition and headlights off, identify the car
battery lead by grounding one lead of the test bulb
to the chassis and checking the remaining exposed
wires from the cut radio connector plug.
If your car is not wired for an audio unit:
Go to the fuse block and find the fuse port for the
battery, usually marked BAT.
Speakers
Identify the car speaker leads. There are two leads
for each speaker which are usually color coded.
A handy way to identify the speaker leads and the
speaker they are connected with is to test the leads
using a 1.5 V AA battery as follows.
Hold one lead against one pole of the battery and
stroke the other lead across the other pole. You will
hear a scraping sound in one of the speakers if you
are holding a speaker lead.
If not, keep testing different lead combinations until
you have located all the speaker leads. When you
label them, include the speaker location for each.
Antenna Motor
If your car is equipped with an automatic power an-
tenna, identify the car motor antenna lead by con-
necting one bulb tester lead to the car battery lead
and touching the remaining exposed wires from the
cut radio connector plug one at a time. You will
hear the antenna motor activate when you touch
the correct wire.
Antenna
The antenna lead is a thick, black wire with a metal
plug at the end.
❐ Connect All Leads
Now that you have identified all the wires in the car,
you are ready to begin connecting them to the
stereo unit wires. The wiring diagram (➡ pages 25,
26) shows the proper connections and color coding
of the leads.
We strongly recommend that you test the unit be-
fore making a final installation.
You can set the unit on the floor and make tempo-
rary connections to test the unit. Use electrical tape
to cover all exposed wires.
Speakers
Connect the speaker wires. See the wiring diagram
(➡ pages 25, 26) for the proper hookups. Follow
the diagram carefully to avoid damaging the speak-
ers and the stereo unit.
The speakers used must be able to handle more
than 45 W of audio power. If using an optional
audio amplifier, the speakers should be able to han-
dle the maximum amplifier output power. Speakers
with low input ratings can be damaged. Speaker
impedance should measure 4–8 ≠, which is typi-
cally marked on most speakers. Lower or higher
impedance speakers will affect output and can
cause both speaker and stereo unit damage.
Motor Antenna
Connect the car motor antenna lead to the dark
blue motor antenna relay control lead.
Battery
Connect the yellow battery lead to the correct radio
wire or to the battery fuse port on the fuse block.
Antenna
Connect the antenna by plugging the antenna lead
into the antenna receptacle.
Equipment
Connect any optional equipment such as an ampli-
fier, according to the instructions furnished with
the equipment. Leave about 12z (30 cm) of dis-
tance between the speaker leads/amplifier unit and
the antenna/antenna extension cord. Read the oper-
ating and installation instructions of any equipment
you will connect to this unit.
Power
Connect the red power lead to the correct car radio
wire or to the appropriate fuse port on the fuse
block.
If the stereo unit functions properly with all these
connections made, disconnect the wires and pro-
ceed to the final installation.
❐ Final Installation
❐ Final Checks
Lead Connections
Connect all wires, making sure that each connec-
tion is insulated and secure. Bundle all loose wires
and fasten them with tape so they will not fall down
later. Now insert the stereo unit into the mounting
collar.
Congratulations! After making a few final checks,
you’re ready to enjoy your new auto stereo system.
1. Make sure that all wires are properly connected
and insulated.
2. Make sure that the stereo unit is securely held in
the mounting collar.
3. Turn on the ignition to check the unit for proper
operation.
If you have difficulties, consult your nearest author-
ized professional installer for assistance.
❐ Preparation
≥ We strongly recommend that you wear gloves
for installation work to protect yourself from
injuries.
≥ When bending the mounting tabs of the
mounting collar with a screwdriver, be careful
not to injure your hands and fingers.
≥ Disconnect the cable from the negative
-
battery
terminal (see caution below).
≥ Unit should be installed in a horizontal position
with the front end up at a convenient angle, but
not more than 30o.
Caution:
≥ Do not disconnect the battery terminals of a
car with a trip or navigational computer since
all user settings stored in memory will be lost.
Instead take extra care with installing the unit
to prevent shorts.
Less than 30x
Dashboard Installation
Installation Opening
(182 mm)
(53 mm)
7
5
/
32
q
2
3
/
32
q
This unit can be installed in any dashboard having
an opening as shown above. The dashboard should
be
3
⁄16z (4.75 mm)j
7
⁄32z (5.56 mm) thick in order to
be able to support the unit.
Important:
≥ Connect the red power lead last, after you
have made and insulated all other connec-
tions.
Ground
Connect the black ground lead of the power con-
nector to the metal car chassis.
E
N
G
L
I
S
H
14
CQ-DF402/DFX302U
23
E
N
G
L
I
S
H
13
CQ-DF402/DFX302U
22
Installation Guide (Continued)
First complete the electrical connections, and
then check them for correctness. (➡ pages
25, 26)
6 Power connector
Lock lever (§)
Mounting tabs
5 Mounting bolt
❐ Installation Procedures
Insert mounting collar 1 into the dashboard, and
bend the mounting tabs out with a screwdriver.
Make sure that the lock lever (§) is flush with the
mounting collar 1 (not projecting outward).
(a) Using the rear support strap 3
4 Tapping screw
2 Hex. nut
3 Rear support
strap
5 Mounting bolt
1 Mounting collar
Fire wall of car
3 mm·
(b) Using the rubber cushion (option)
5 Mounting bolt
1 Mounting collar
Rear support bracket
(provided on the car)
Rubber cushion (option)
Lock lever (§)
1
Secure the rear of the unit.
After fixing mounting bolt
5
and power connector
6
, fix the rear of the unit to the car body by either
method (a) or (b) shown below.
Insert trim plate 8.
After installation, reconnect the negative - bat-
tery terminal.
2
3
4
Remove the removable face plate.
1 Press [OPEN]. The removable face plate will
be opened.
2 Push the face plate to either the right or left.
3 Pull it out toward you.
1
2
Remove the Unit
Lock lever
Lock lever
Screwdriver
8 Trim plate
REP
5W
X
4
RANDOM
OPEN
PWR
Remove the trim plate 8 with a screwdriver.
Pull out the unit while pushing down the lock
lever with a screwdriver.
Remove the unit pulling with both hands.
1
2
3
4
1 Open
2 Push
3 Pull out
Contact
Main unit
Switch off the power of the unit.
E
N
G
L
I
S
H
16
CQ-DF402/DFX302U
25
E
N
G
L
I
S
H
15
CQ-DF402/DFX302U
24
Electrical ConnectionsAnti-Theft System
Display Security indicator
Blinks
OFF
Security Indicator
The security indicator blinks when the removable
face plate is removed from the unit.
Press and hold [SEL] to turn the security indicator
on or off. (“LED ON” or “LED OFF”).
Install Removable Face Plate
1 Fit the face plate with its right or left hole on
one of the pins provided on the main unit.
2 Fit the other hold on the other pin applying
slight pressure.
3 Move the face plate up and down a few times to
make sure it is secure. Then close the front
panel and press down the right side of the face
plate until it clicks into plate.
Cautions:
≥ This face plate is not water-proof. Do not expose it to water or excessive moisture.
≥ Do not remove the face plate while driving your car.
≥ Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level.
≥ Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical
contacts.
≥ If dirt or other foreign substances get on the contacts, wipe them off with a clean and dry cloth.
≥ Do not apply a strong downward force onto the face plate and do not put anything on it while it is open, or
it might be damaged.
This unit is equipped with a removable face plate. Removing this face plate makes the radio totally inoperable.
The security indicator will blink.
Place the Removable Face
Plate into Case
1 Switch off the power of the unit.
2 Remove the removable face plate. (➡ page 23)
3 Gently press the button of the case and open
the cover. Place the face plate into the case and
take it with you when you leave the car.
1
2
3
7 Removable face plate case
Security indicator
Contact
Default
❐ Wiring Diagram
Only for CQ-DFX302U
No. Item Q’ty
6 Power connector 1
Recommended external amplifier combination (example)
≥Pre-amp out (rear/front) [CY-M9054 (4 channels system)]
≥Subwoofer out [CY-M9054 (2 channels system) or CY-M7052 (1 channel system)]
White
Red
(MONO)
Power connector
Antenna
6
Yellow
BATTERY 15A
Battery lead
To the car battery,
continuous +12 V DC
Fuse (15 A)
Red
Resistor (1 k≠)
ACC
Power lead
To ACC power,
+12 V DC
Dark blue
Motor antenna relay control lead
(To motor antenna) (Max. 500 mA)
This lead is not intended for use with switch
actuated power antenna.
Black
Ground lead
To a clean, bare metallic
part of car chassis.
(r)(s)(r)(s)(r)(s)(r)(s)
Left speaker
(Front)
Right speaker
(Front)
White Gray Green VioletWhite/black stripe
Green/black
stripe
Violet/black stripe
Gray/black stripe
FRONT SP REAR SP
Left speaker
(Rear)
Right speaker
(Rear)
S•W-OUT
Speaker lead
Subwoofer cord
CQ-DFX302U
Pre-Amp output connector (Front)
Pre-Amp output connector (Rear)
L (White)
R (Red)
Amp. relay control power lead
This lead is for connection to the power amplifier.
Cautions:
≥ This product is designed to operate of a 12 V DC, negative ground battery system.
≥ To prevent damage to the unit, be sure to follow the wiring diagram below.
≥ Remove approx.
1
⁄4z (5 mm) of protective covering from the ends of the leads before connecting.
≥ Do not insert the power connector into the unit until the wiring is completed.
≥ Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all cables
and keep cable terminals free from touching any metal parts.
≥ Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
Accessory used for wiring
Station is too far, or signals are too weak.
➡Select other stations of higher signal level.
Battery cable is not correctly connected.
➡Connect the battery cable to the terminal that is always live.
Fuse is burnt.
➡Call the store where you purchased the unit, or your nearest Servicenter
(see the attached sheet) and ask for fuse replacement.
E
N
G
L
I
S
H
18
CQ-DF402/DFX302U
27
Troubleshooting
E
N
G
L
I
S
H
17
CQ-DF402/DFX302U
26
Electrical Connections (Continued)
White
Red
(MONO)
Power connector
Antenna
6
CD changer control connector
CD changer
CX-DP88U
Battery lead
Yellow
DIN cord
Fuse (3 A)
Yellow
BATTERY 15A
Battery lead
To the car battery,
continuous +12 V DC
Fuse (15 A)
Red
Resistor (1 k≠)
ACC
Power lead
To ACC power,
+12 V DC
Dark blue
Black
Ground lead
To a clean, bare metallic
part of car chassis.
CD
•
C-IN
White (L)
Red (R)
White (L)
Red (R)
White (L)
Red (R)
(r)(s)(r)(s)(r)(s)(r)(s)
Left speaker
(Front)
Right speaker
(Front)
White Gray Green VioletWhite/black stripe
Green/black
stripe
Violet/black stripe
Gray/black stripe
FRONT SP REAR SP
Left speaker
(Rear)
Right speaker
(Rear)
S•W-OUT
REAR
FRONT
Preout cord (rear)
Preout cord (front)
Speaker lead
Ground lead
Be sure to connect to a well
grounded metallic part of your car
because noises or troubles may occur.
DIN extension cord (DIN/BATT/RCA/GND)
Black
Subwoofer cord
RCA cord
CQ-DF402U
Motor antenna relay control lead
(To motor antenna) (Max. 500 mA)
This lead is not intended for use with
switch actuated power antenna.
Amp. relay control power lead
This lead is for connection to the power amplifier.
❐ Wiring Diagram
Only for CQ-DF402U
Preliminary Steps
Check and take steps as described in the tables below.
If You Suspect Something Wrong
Immediately switch power off.
Disconnect the power connector and check that there is nei-
ther smoke nor heat from the unit before asking for repairs.
Never try to repair the unit by yourself because it is dangerous
to do so.
No power.
Trouble
Car’s engine switch is not on.
➡Turn your car’s ignition switch to ACC or ON.
Troubleshooting Tips
❐ Common
Cables are not correctly connected.
➡Connect cables correctly.
Battery cable is not correctly connected.
➡Connect the battery cable to the terminal that is always active.
Accessory cable is not correctly connected.
➡Connect the accessory cable to your car’s ACC source.
Grounding wire is not correctly connected.
➡Connect the grounding wire to a metal part of the car.
No sound.
Mute is set to ON.
➡Set it to OFF.
Cables are not correctly connected.
➡Connect cables correctly.
Condensation (dew)
➡Wait for a while before use.
Cautions:
≥ Do not use the unit if it malfunctions or
if there is something wrong.
≥ Do not use the unit in abnormal condi-
tion, for example, without sound, or
with smoke or foul smell, can cause ig-
nition or electric shock. Immediately
stop using it and call the store where
you purchased it.
Cause/Step
❐ Radio
Much noise in FM stereo
and monaural broadcasts.
Preset station is reset.
The first track of a mix mode disc was reproduced. (Mix mode is a format in
which data except music is recorded on the first track and music data is recorded
on other than the first track in a session.)
➡Play back music data recorded on other than the first track.
Instable mounting.
➡Mount the unit securely with the mounting parts, referring to the section on
installation.
≥ Disc is dirty.
≥ Disc has scratches.
➡Clean disc, referring to the section on “Notes on CD/CD media (CD-R,
CD-RW)”.
E
N
G
L
I
S
H
20
CQ-DF402/DFX302U
29
E
N
G
L
I
S
H
19
CQ-DF402/DFX302U
28
Troubleshooting
(Continued)
Mounting angle is over 30o.
➡Adjust mounting angle to less than 30o.
≥ Disc is defective.
≥ Mechanical trouble.
➡Press [OPEN] to open the panel and press [<] (EJECT). If normal operation
is not restored yet, call the store where you purchased the unit or the near-
est Servicenter to ask for repairs.
Sound skips, bad sound
quality. (e.g. caused by
noise)
Sound skips due to vibra-
tion.
Disc is not ejected.
Time is counted but no
sound comes out.
Disc is in the CD compart-
ment but no sound is
made, or disc is ejected
automatically.
Disc is upside down.
➡Place disc in the correct direction, and the label side up.
❐ CD
A disc that has data other than CD-DA type is loaded.
➡Discs that have CD-DA type data should be used.
➡The unit may not successfully play back a CD-R/RW that is made in combi-
nation of writing software, a CD recorder (CD-R/RW drive) and a disc which
are incompatible one another. Refer to instructions for the concerned de-
vices for details.
➡The unit may not successfully play back a CD-R/RW that is made in combi-
nation of writing software, a CD recorder (CD-R/RW drive) and a disc which
are incompatible one another. Refer to instructions for the concerned de-
vices for details.
Trouble Cause/Step
No sound from left, right,
front or rear speakers.
Left and right balance, or front and rear balance is off on one side.
➡Adjust balance/fader mode as appropriate.
❐ Sound Setting
The right speaker wire is connected to the left speaker and the left speaker wire
to the right speaker.
➡Connect the speaker wires to the correct ones.
Left and right sounds are
reversed in stereo listen-
ing.
Buttons are invalid for op-
eration.
Battery poles (i) (j) are reversed.
➡Insert the battery correctly.
❐ Remote Control
Wrong the battery.
➡Check the battery.
Battery has run down.
➡Replace the battery.
Remote control is in the wrong direction.
➡Direct the remote control at sensor (REMOTE) on the panel.
Trouble Cause/Step
Cables are not correctly connected.
➡Connect the cables correctly.
Error Display Messages
❐ CD
Disc has scratches.
➡Press [OPEN] to open the front panel, and then press [<] (EJECT) to eject
the disc.
≥ Disc is dirty, or is upside down.
≥ A disc that has data other than CD-DA type is loaded.
➡Press [OPEN] to open the front panel, and then press [<] (EJECT) to eject
the disc.
No operation by some cause.
➡Turn off the car engine (ACC off) and remove the fuse from the battery lead
(yellow) for 1 minute. Then reinstall the fuse.
Display Cause/Step
❐ CD Changer
Disc has scratches.
➡Select the next available compact disc.
≥ Disc is dirty, or is upside down.
≥ A disc other than a music CD (CD-DA type) is loaded.
➡Select the next available compact disc.
No disc in the changer (magazine).
➡Insert discs into the changer (magazine).
No operation by some cause.
➡Press [RESET] on the CD changer (optional).
Notes:
≥ There may be cases where the disc numbers affected by an error are displayed before “E1” or “E2”.
≥ Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the
operating instructions for the changer used.
DISC No.
DISC No.
Only for CQ-DF402U
≥ Disc is dirty.
≥ Disc has scratches.
➡Clean disc, referring to the section on “Notes on CD/CD media (CD-R,
CD-RW)”.
E
N
G
L
I
S
H
22
CQ-DF402/DFX302U
31
Specifications
E
N
G
L
I
S
H
21
CQ-DF402/DFX302U
30
Maintenance
❐ General
Power supply: 12 V DC (11 Vj16 V),
test voltage 14.4V,
negative ground
Current consumption: Less than 2.2 A
(CD play mode;
0.5 Wa4 channels)
Maximum power output: 45 Wa4 channels at
400 Hz, Volume
control maximum
Tone adjustment range:
Bass: n12 dB at 100 Hz
Treble: n12 dB at 10 kHz
Suitable speaker impedance: 4j8 ≠
Pre-Amp output voltage: 2.0 V (CD play mode;
1 kHz, 0 dB)
Subwoofer output voltage: 2.0 V
Output impedance: 200 ≠
Dimensions (WaHaD): 7za1
15
/16za5
7
/8z
(178a50a150 mm)
Weight: 3 lbs. 5 oz (1.5 kg)
❐ FM Stereo Radio
Frequency range: 87.9 MHzj107.9 MHz
Usable sensitivity: 11.0 dBf.
(1.25
¨V,
75 ≠)
50 dB quieting sensitivity:
15.2 dBf.
(1.6
¨V,
75 ≠)
Frequency response: 30 Hzj15 kHz
(n3 dB)
Alternate channel selectivity: 75 dB
Stereo separation: 42 dB (1 kHz)
Image response ratio: 75 dB
IF response ratio: 100 dB
Signal/noise ratio: 70 dB
❐ AM Radio
Frequency range: 530 kHzj1 710 kHz
Usable sensitivity: 28 dB/¨V
(25
¨V,
S/N 20 dB)
❐ CD Player
Sampling frequency: 32 times oversampling
DA converter: MASH • 1 bit/
4 DAC system
Error correction system: Panasonic super
decoding algorithm
Pick-up type: Astigma 3-beam
Light source: Semiconductor laser
Wave length: 780 nm
Frequency response: 20 Hzj20 kHz
(n1 dB)
Signal/noise ratio: 96 dB
Total harmonic distortion: 0.01 % (1 kHz)
Wow and flutter: Below measurable
limits
Channel separation: 75 dB
Above specifications comply with EIA standards.
Note:
≥ Specifications and the design are subject to modifi-
cation without notice due to improvements in tech-
nology.
Maintenance
Your product is designed and manufactured to ensure a minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner or other solvents.
Product Servicing
If the suggestions in the charts do not solve the problem, we recommend that you take it to your nearest au-
thorized Panasonic Servicenter. The product should be serviced only by a qualified technician.
Replacing the Fuse
Use fuses of the same specified rating (15 A). Using different substitutes or fuses with higher ratings, or con-
necting the unit directly without a fuse, could cause fire or damage to the stereo unit.
If the replacement fuse fails, contact your nearest Panasonic Servicenter for service.
❐ Cleaning this Unit
Use a dry, soft cloth to wipe.
❐ Caution on Cleaning
Never use solvents such as benzine, thinner as they
may mar the surface of the unit.
Label side
<Right> <Wrong>
Rough edges
Do not use irregular shaped discs.
Notes on CD/CD Media (CD-R, CD-RW)
Care of the Unit
How to hold the disc
≥ Do not touch the underside of the disc.
≥ Do not scratch the disc.
≥ Do not bend disc.
≥ When not in use, keep the disc in the case.
Do not use irregular shaped discs.
Do not leave discs on the following places:
≥ Direct sunlight
≥ Near car heaters
≥ Dirty, dusty and damp areas
≥ Seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
Caution on new discs
A new disc may have rough edges on its inner and outer
perimeter. These may cause malfunction.
Remove the rough edges using a pencil, etc.
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ball-
point pen stroke.
Do not play any ordinary music CDs with labels
other than this one.
Notes on CD-Rs/RWs
≥ You may have trouble playing back some CD-R/RW discs recorded on CD recorders (CD-R/RW drives), ei-
ther due to their recording characteristics or dirt, fingerprints, scratches, etc. on the disc surface.
≥ CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving
them inside a car for extended periods may damage them and make playback impossible.
≥ The unit may not successfully play back a CD-R/RW that was made by the combination of writing software, a
CD recorder (CD-R/RW drive) and a disc if they are incompatible one another.
≥ This player cannot play CD-R/RW discs if the session is not closed.
≥ This player cannot play the CD-R/RW discs which contains other than CD-DA data.
≥ Be sure to observe the instructions of CD-R/RW disc for handling it.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
Panasonic Sales Company.
Division of Matsushita Electric of
Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infanteria, Km. 9.5
San Gabriel Industrial Park,
Carolina, Puerto Rico 00985
http://www.panasonic.com
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario
L4W 2T3
http://www.panasonic.ca
YEFM283862 F1201-1052 Printed in China
Imprimé en Chine
Impreso en China
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Panasonic CQDFX302U - AUTO RADIO/CD DECK Operating Instructions Manual

Panasonic
Marque
Panasonic
Modèle
CQDFX302U - AUTO RADIO/CD DECK
Catégorie
Lecteur CD
Taper
Operating Instructions Manual
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes