Frigidaire FGGH3047VF Guide d'installation

Marque: Frigidaire

Modèle: FGGH3047VF

Catégorie: Micro-ondes

Taper: Guide d'installation

INSTALLATION INSTRUCTIONS

FRONT CONTROL FREESTANDING GAS RANGE

INSTALLATION AND SERVICE MUST BE

PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

IMPORTANT SAFETY INSTRUCTIONS

If the information in this manual is not

followed exactly, a re or electrical shock may result causing

property damage, personal injury or death.

FOR YOUR SAFETY:

— Do not store or use gasoline or other ammable vapors

and liquids in the vicinity of this or any other appliance.

— WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re

department.

— Installation and service must be performed by a qualied

installer, service agency or the gas supplier.

Important Notes to the Installer:

• Read all instructions contained in these installation

instructions before installing range.

• Remove all packing material from the oven

compartments before connecting the gas & electrical

supply to the range.

• Observe all governing codes and ordinances.

• Be sure to leave these instructions with the

consumer.

Important Notes to the Consumer:

Keep these instructions with your owner’s guide for

future reference.

• As when using any appliance generating heat, there

are certain safety precautions you should follow.

These are listed in the Use & Care Guide, read it

carefully.

Tip Over Hazard

Range

leveling leg

Anti-tip

bracket

• A child or adult can tip the

range and be killed.

• Verify the anti-tip device has

been installed to floor or wall.

• Ensure the anti-tip device is re-engaged to floor

or wall when the range is moved.

• Do not operate the range without the anti-tip

device in place and engaged.

• Failure to follow these instructions can result in

death or serious burns to children and adults.

To check if the anti-tip bracket is installed properly, use

both arms to grasp the rear edge of the range back.

Carefully attempt to tilt range forward. When properly

installed, the range should not tilt forward.

Refer to the anti-tip bracket installation instructions

supplied with your range for proper installation.

FOR YOUR SAFETY: Do not

store or use gasoline or other ammable

vapors and liquids in the vicinity of this or

any other appliance.

• Be sure your range is installed and grounded properly

by a qualied installer or service technician.

• Make sure the wall coverings around the range can

withstand the heat generated by the range.

• To eliminate the need to reach over the surface

elements, cabinet storage space above the elements

should be avoided.

P/N 809127206 (1901) Rev. A

English – pages 1-13

French – pages 14-26

Spanish – pages 27-40

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Provide proper fuel type

Before proceeding: Your range is factory preset to operate

on natural gas. If L.P. conversion is needed, contact your

local L.P. Gas provider for assistance.

The L.P. conversion kit may be located on the lower rear

back panel of the range. If no L.P. kit is provided, contact

your product dealer to obtain the correct L.P. conversion

kit.

• Installation of this range must conform with local codes

or, in the absence of local codes, with the National

Fuel Gas Code ANSI Z223.1—latest edition when

installed in the United States.

• When installed in a manufactured (mobile) home,

installation must conform with the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part

3280 [formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD (Part 280)] or,

when such standard is not applicable, the Standard

for Manufactured Home Installations, ANSI/NCSBCS

A225.1, or with local codes.

• This range has been design certied by CSA

International. As with any appliance using gas and

generating heat, there are certain safety precautions

you should follow. You will nd them in the Use & Care

Guide, read it carefully.

• Be sure your range is installed and grounded properly

by a qualied installer or service technician.

• This range must be electrically grounded in

accordance with local codes or, in their absence, with

the National Electrical Code ANSI/NFPA No .70—

latest edition when installed in the United States. See

Grounding Instructions on page 9.

• Before installing the range in an area covered with

linoleum or any other synthetic oor covering, make

sure the oor covering can withstand heat at least

90°F above room temperature without shrinking,

warping or discoloring. Do not install the range over

carpeting unless you place an insulating pad or sheet

of 1/4-inch thick plywood between the range and

carpeting.

• Make sure the wall coverings around the range can

withstand the heat generated by the range.

• Do not obstruct the ow of combustion air at the oven

vent nor around the base or beneath the lower front

panel of the range. Avoid touching the vent openings

or nearby surfaces as they may become hot while the

oven is in operation. This range requires fresh air for

proper burner combustion.

• Air curtain or other overhead range hoods, which

operate by blowing a downward air ow on to a range

or cooktop, shall not be used in conjunction with gas

ranges other than when the hood and range have

been designed, tested and listed by an independent

test laboratory for use in combination with each other.

DO NOT MAKE ANY ATTEMPT TO

OPERATE THE ELECTRIC IGNITION OVEN DURING

AN ELECTRICAL POWER FAILURE. RESET ALL OVEN

CONTROLS TO “OFF” IN THE EVENT OF A POWER

FAILURE.

The electric ignitor will automatically re-ignite the oven

burner when power resumes if the oven thermostat control

was left in the “ON” position.

When an electrical power failure occurs during use, the

surface burners will continue to operate.

During a power outage, the surface burners can be lit with

a match. Hold a lighted match to the burner, then slowly

turn the knob to the LITE position. Use extreme caution

when lighting burners this way.

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Never leave children alone or

unattended in the area where an appliance is in use. Teach

children the proper, safe use of all appliances. Never leave

the oven door open when the range is unattended.

Stepping, leaning or sitting on the doors or

drawers of this range can result in serious injuries and can

also cause damage to the range.

• Do not store items of interest to children in the

cabinets above the range. Children could be seriously

burned climbing on the range to reach items.

• To eliminate the need to reach over the surface

burners, cabinet storage space above the burners

should be avoided.

• Adjust surface burner ame size so it does not extend

beyond the edge of the cooking utensil. Excessive

ame is hazardous.

• Do not use the oven as a storage space. This creates

a potentially hazardous situation.

• Never use your range for warming or heating the

room. Prolonged use of the range without adequate

ventilation can be dangerous.

• Do not store or use gasoline or other ammable

vapors and liquids near this or any other appliance.

Explosions or res could result.

• Reset all controls to the “OFF” position after using a

programmable timing operation.

• Unlike some gas ranges, the cooktop is not removable.

Do not attempt to remove the cooktop.

Special instructions for appliances installed in the state of

Massachusetts:

This Appliance can only be installed in

the state of Massachusetts by a Massachusetts licensed

plumber or gas tter. When using a exible connector, it

must not exceed three (3) feet (36 in.) long. A “T” handle

type manual gas valve must be installed in the gas supply

line to this appliance.

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

1. Clearances and Dimensions

a. Provide adequate clearances between the range and adjacent combustible surfaces.

b. Location—Check location where the range will be installed. Check for proper electrical supply and gas supply and the stability of oor.

c. Dimensions that are shown must be used. Given dimensions provide minimum clearance. Contact surface must be

solid and level.

WALL

CABINET

WALL

CABINET

Gas location

Open space

for gas

This space

must

remain clear

5”

30” Minimum*

Minimum to

wall on either

side of range

above 36” height.

36”

18”

Minimum to

cabinets on

either side

of range

25” Max.

13”

Maximum depth

for cabinets

above range top.

0” clearance below cooking top and at rear of range

Typical cabinet installationFront

view

Side

view

30”

Minimum

30”

Minimum

*30" (762 mm) MINIMUM CLEARANCE BETWEEN THE

TOP OF THE COOKING SURFACE AND THE BOTTOM

OF AN UNPROTECTED WOOD OR METAL CABINET; OR

24" (610 mm) MINIMUM WHEN BOTTOM OF WOOD OR

METAL CABINET IS PROTECTED BY NOT LESS THAN

1/4" (6 mm) FLAME RETARDANT MILLBOARD COVERED

WITH NOT LESS THAN NO. 28 MSG SHEET STEEL, 0.015"

(0.4 mm) STAINLESS STEEL, 0.024" (0.6 mm) ALUMINUM

OR 0.020" (0.5 mm) COPPER. 0" (0 mm) CLEARANCE IS

THE MINIMUM FOR THE REAR OF THE RANGE. FOLLOW

ALL DIMENSION REQUIREMENTS PROVIDED ABOVE

TO PREVENT PROPERTY DAMAGE, POTENTIAL FIRE

HAZARD, AND INCORRECT COUNTERTOP AND CABINET

CUTS.

TO ELIMINATE THE RISK OF BURNS OR FIRE BY

REACHING OVER HEATED SURFACE UNITS, CABINET

STORAGE SPACE LOCATED ABOVE THE SURFACE UNITS

SHOULD BE AVOIDED. IF CABINET STORAGE IS TO BE

PROVIDED, THE RISK CAN BE REDUCED BY INSTALLING

A RANGE HOOD THAT PROJECTS HORIZONTALLY A

MINIMUM OF 5" (127 mm) BEYOND THE BOTTOM OF

THE CABINETS.

DO NOT MAKE ANY ATTEMPT TO

OPERATE THE ELECTRIC IGNITION OVEN DURING

AN ELECTRICAL POWER FAILURE. RESET ALL OVEN

CONTROLS TO OFF IN THE EVENT OF A POWER

FAILURE. The electric ignitor will automatically re-

ignite the oven burner when power resumes if the oven

thermostat control was left in the ON position.

When an electrical power failure occurs during use, the

surface burners will continue to operate.

During a power outage, the surface burners can be lit

with a match. Hold a lighted match to the burner, then

slowly turn the knob to the Lite position. Use extreme

caution when lighting burners this way.

Maximum

47"

Door open

Fig.1

Fig.2

Fig.3

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

2. Tools You Will Need

Fig. a

(Wear safety glasses when using tools):

For leveling legs and Anti-Tip Bracket:

• Adjustable wrench or channel lock pliers (Fig. a)

• 5/16” Nutdriver or at head screwdriver (Fig. b)

• Electric drill & 1/8” drill bit (3/16” Masonry drill bit if

installing in concrete) (Fig. c)

• Level (Fig. d)

For gas supply connection:

• Adjustable wrench and pipe wrench (Figs. a & e)

For burner ame adjustment:

• Phillips head and small at-blade screwdrivers (Figs. f

& g)

Materials you will need:

• Pipe joint sealant that resists action of LP/Propane gas

(Fig. h)

• Gas line manual shut-o valve (Fig. i)

• A new exible metal appliance conduit (1/2” NPT x

3/4” or 1/2” I.D.) must be design certied by CSA

International. Because solid pipe restricts moving the

range, we recommend using a new exible conduit

(4 to 5 foot length) for each new installation and

additional reinstallations. (Fig. j)

• Use new are union adapters (1/2” NPT x 3/4” or 1/2”

I.D.) (Fig. k)

Materials supplied with appliance:

• Anti-Tip Template (Fig. l)

• Anti-Tip bracket; includes 2 mounting screws (Fig. m)

Tools

Fig. f

Materials

Fig. h

Fig. i

Fig. j

Fig. k

Fig. d

Fig. c

Fig. g

Fig. b

Fig. e

Fig. l

Fig. m

Materials supplied with appliance

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

For oor mount, locate the bracket by placing back edge

of the template where the rear of the range will be located.

Mark the location of the screw holes, shown in template.

B. Drill Pilot Holes and Fasten

Bracket - Drill a 1/8” (3 mm)

pilot hole where screws are

to be located. If bracket is to

be mounted to the wall, drill

pilot hole at an approximate

20° downward angle. If

bracket is to be mounted to

masonry or ceramic oors,

drill a 5/32” (4 mm) pilot hole

1-3/4” (44 mm) deep. The

screws provided may be

used in wood or concrete material. Use a 5/16” (8 mm)

nut-driver or at head screwdriver to secure the bracket

in place.

C. Level and Position Range - Level range by adjusting the

(4) leveling legs with a wrench. Note: Aminimum clearance

of 1/8” (3 mm) is required between the bottom of the

range and the leveling leg to allow room for the bracket.

Use a spirit level to check your adjustments. Slide range

back into position. Visually check that rear leveling leg

is inserted into and fully secured by the Anti-Tip Bracket

by removing lower panel or storage drawer. For models

with a warmer drawer or broiler compartment, grasp the

top rear edge of the range and carefully attempt to tilt it

forward.

3. Anti-Tip Bracket Installation

Instructions

Important Safety Warning

To reduce the risk of tipping of the range, the range should

be secured to the oor by properly installed anti-tip bracket

and screws packed with the range. Failure to install the

anti-tip bracket will allow the range to tip over if excessive

weight is placed on an open door or if a child climbs upon

it. Serious injury might result from spilled hot liquids or from

the range itself.

If range is ever moved to a dierent location, the anti-tip

brackets must also be moved and installed with the range.

Instructions are provided for installation in wood or cement

fastened to either the oor or wall. When installed to the

wall, make sure that screws completely penetrate dry wall

and are secured in wood or metal. When fastening to the

oor or wall, be sure that screws do not penetrate electrical

wiring or plumbing.

A. Locate the Bracket Using the Template - (Bracket may be

located on either the left or right side of the range. Use

the information below to locate the bracket if template is

not available). Mark the oor or wall where left or right

side of the range will be located. If rear of range is against

the wall or no further than 1-1/4" (32 mm) from wall when

installed, you may use the wall or oor mount method. If

molding is installed and does not allow the bracket to t

ush against the wall, remove molding or mount bracket

to the oor. For wall mount, locate the bracket by placing

the back edge of the template against the rear wall and

the side edge of template on the mark made referencing

the side of the range. Place bracket on top of template

and mark location of the screw holes in wall. If rear of

range is further than 1-1/4" (32 mm) from the wall when

installed, attach bracket to the oor.

(31.75mm)

Fig. 4

Fig. 5

Fig. 6

Fig. 7

(17 mm)

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Fig. 9

Be sure to stabilize the left side of the gas pressure

regulator before tightening ANY ttings to the pressure

regulator. Do not allow pressure regulator to turn on

pipe when tightening ttings (Refer to Fig. 9).

Fig. 8 - gas supply connections

4. Provide an adequate gas

supply.

Please note: Operation at elevations above 2000 ft.,

appliance rating shall be reduced at the rate of 4 percent

for each 1000 ft. above sea level.

This appliance is pre-set to operate on 4” natural gas

manifold pressure. A convertible pressure regulator is

connected to the manifold and MUST be connected

in series with the gas supply line. If the LP/Propane

conversion kit has been used, follow instructions provided

with the kit for converting the pressure regulator to LP/

Propane use.

Care must be taken during installation of range not to

obstruct the ow of combustion and ventilation air.

For proper operation, the maximum inlet pressure to the

regulator should be no more than 14 inches of water

column pressure. The inlet pressure to the regulator must

be at least 1 inch greater than regulator manifold pressure.

Example: If regulator is set for natural gas 4 inch manifold

pressure, inlet pressure must be at least 5 inches; if

regulator has been converted for LP/Propane gas 10

inch manifold pressure, inlet pressure must be at least 11

inches.

Leak testing of the appliance shall be conducted according

to the instructions in step 4g.

The gas supply line should be 1/2” or 3/4” I.D.

5. Seal wall openings.

Seal any openings in the wall behind the range and in the

oor under the range after gas supply line is installed.

6. Connect range to gas

supply.

Note: To prevent leaks use pipe joint sealant on all male

(outside) pipe threads. Do not allow gas pressure reg-

ulator to turn on pipe when tightening ttings.

a. Install an external manual gas shut-o valve to gas

supply line in an accessible location outside of range.

Be sure you know where and how to shut o the gas

supply to the range (See Fig. 8).

b. Install 1/2” are union adapter to gas pressure

regulator using no more than 15ft./lbs. of torque (Refer

to Fig. 8).

Pressure

regulator Flexible appliance

conduit

Flare

union

adaptor

Manual

shut-o

valve

Flare

union

adaptor

OFF

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Checking manifold gas pressure

Do not use ame to check for gas leaks.

Disconnect the range and its individual shut-o valve from

the gas supply piping system during any pressure testing

of that system at test pressures greater than 14” of water

column pressure (approximately 1/2” psig).

The appliance must be isolated from the gas supply

piping system by closing its individual manual shut-o

valve during any pressure testing of the gas supply piping

system at test pressures equal to or less than 14” of water

column pressure (approximately 1/2” psig).

If it should be necessary to check the manifold gas

pressure, connect manometer (water gauge) or other

pressure device to the top burner right rear orice. Using

a rubber hose with inside diameter of approximately 1/4,”

hold tubing down tight over orice. Turn burner valve on.

For an accurate pressure check have at least two (2)

other top burners burning. Be sure the gas supply (inlet)

pressure is at least one inch above specied range

manifold pressure. The gas supply pressure should never

be over 14” water column. When properly adjusted for

Natural Gas the manifold pressure is 4”. For LP/Propane

Gas the manifold pressure is 10”.

c. Tighten the gas supply tting and/or appliance conduit

to are union adaptor on the right side of the pressure

regulator (refer to Fig. 10) using NO MORE THAN

15ft./lbs. of torque. Be sure to stabilize the 1/2” are

union adapter with an adjustable wrench before

tightening the gas supply tting and/or appliance

conduit.

d. Install are union adapter to external manual shut-o

valve (See Fig. 8).

e. Attach exible appliance conduit to are union adaptor

on shut-o valve (See Fig. 8).

f. Make sure the service shut-o valve on pressure

regulator is set to the ON position (See Fig. 11).

Fig. 10

g. Check for gas leaks. Turn the gas supply on to the

range and use a liquid leak detector at all joints and

conduits to check for leaks in the system.

Fig. 11

Pressure

regulator

Service shut-o valve

(shown in ON position)

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Grounding instructions:

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong grounding wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

The customer should have the wall receptacle and circuit

checked by a qualied electrician to make sure the

receptacle is properly grounded and polarized.

Do not, under any

circumstances, cut,

remove or bypass the

grounding prong.

Preferred method

Grounding

type wall

receptacle

Power

supply

cord with

3-prong

grounding

plug

Fig. 12

7. Read the following

electrical connection details

before connecting electricity

to range.

Before servicing, disconnect electrical sup-

ply at circuit breaker, fuse or power cord.

Electric requirements:

A dedicated, properly grounded and polarized branch

circuit protected by a 15 amp. circuit breaker or time delay

fuse. See serial plate for proper voltage.

Extension cord precautions:

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of

any extension cord. However, if you still choose to use an

extension cord, it is absolutely necessary that it be a UL

listed 3-wire grounding type appliance extension cord and

that the current carrying rating of the cord in amperes be

equivalent to or greater than the branch circuit rating. Such

extension cords are obtainable through your local service

organization.

Please read carefully! For personal safety,

this product must be properly grounded.

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord (See Fig. 12).

Where a standard two-prong wall receptacle is

encountered, it is the personal responsibility and obligation

of the customer to have it replaced with a properly ground-

ed three-prong wall receptacle.

8. Check burner cap

placement.

It is very important to be sure that all surface burner caps

and burner grates are properly installed and in the correct

locations before operating the appliance. The cooktop is

not removeable. Do not attempt to remove or lift the cook-

top.

To prevent are-ups and avoid creation of

harmful by-products, do not use the cooktop without all

burner caps properly installed to insure proper ignition and

gas ame size.

Always keep the burner caps and burner heads in place

whenever the surface burners are in use. Do not allow

spills, food, cleaning agents or any other material to enter

the gas orice holder openings.

Check and be sure the size of each burner cap matches

the size of the burner head. Check and be sure that all

round style burner caps are correctly in place on round

burner heads.

Check and be sure that all oval style burner caps are cor-

rectly in place on oval burner heads (if equipped). Check

and be sure that all dual or twin style burner caps are cor-

rectly in place on dual or twin burner heads (if equipped).

On round style burners, the burner cap lip (See Fig. 13)

should t snug into the center of burner head and be level.

Refer to Figs. 14 & 15 for correct and incorrect burner cap

placement.

Once in place, you may check the t by gently sliding the

burner cap from side to side (Fig. 16) to be sure it is cen-

tered and rmly seated. Please note that the burner cap

should NOT move o the center of the burner head when

sliding from side to side.

Fig. 13

Correct burner

cap placement

Fig. 14

Incorrect burner

cap placement

Fig. 15

Fig. 16

Burner

cap

Burner

head

Ignitor

Orice

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Fig. 17

Burner ame size

5/8”

Cooktop

Fig. 18

9. Check ignition of surface

burners.

Operation of electric igniters should be checked after

range and supply line connectors have been carefully

checked for leaks and range has been connected to

electric power.

a. To check for proper ignition, push in and turn a

surface burner knob counterclockwise to the LITE

position. You will hear the igniter sparking.

b. The surface burner should ignite when gas is available

to the burner. Purge air from supply lines by leaving

knob in the LITE position until burner ignites. Each

burner should light within four (4) seconds in normal

operation after air has been purged from supply lines.

c. Visually check that burner has a ame. Once the

burner ignites, the control knob should be turned out of

the LITE position.

d. Try each surface control knob separately until all

surface burners have been checked. Each burner

location is equipped with a separate electrode.

10. Adjust LOW setting of

surface burner valves (linear

ow).

Test to verify if LOW setting should be adjusted:

a. Push in and turn control to LITE until burner ignites.

b. Push in and quickly turn knob to lowest position.

c. If burner goes out, reset control to OFF.

d. Remove the surface burner control knob.

e. Insert a thin-bladed screwdriver into the hollow valve

stem and engage the slotted screw inside. Flame size

can be increased or decreased with the turn of the

screw (see Fig. 17 and Fig. 18).

f. Adjust ame until you can quickly turn knob from

LITE to lowest position without extinguishing the

ame. Flame should be as small as possible without

extinguishing.

Note: Air mixture adjustments are not required on surface

burners.

11. Check ignition of oven

burners.

The operation of oven igniters should be checked after

range and supply line connectors have been carefully

checked for leaks and range has been connected to elec-

tric power. Be sure all packing materials and literature are

removed from oven.

The oven burner is equipped with an electric control sys-

tem as well as an electric oven burner igniter. If your model

is equipped with an upper oven burner, it will also have

an electric burner igniter. These control systems require

no adjustment. When the oven is set to operate, current

will ow to the igniter. It will “glow” similar to a light bulb.

When the igniter has reached a temperature sucient to

ignite gas, the electrically controlled oven valve will open

and ame will appear at the oven burner. There is a time

lapse from 30 to 60 seconds after the thermostat is turned

ON before the ame appears at the oven burner. When the

oven reaches the set temperature, the glowing igniter will

cycle o. The burner ame will turn o in 20 to 30 seconds

after the igniter turns o. To maintain any set oven

temperature, this cycle will continue as long as the oven

control is set to operate.

To check oven burner ignition:

a. Set oven to Bake at 300ºF. See User’s Manual for

operating instructions.

b. Within 60 seconds the oven burner should ignite.

Check for proper ame, and allow the burner to cycle

once. Reset control to OFF.

c. If your model is equipped with a waist-high broiler,

set oven to Broil. See User’s Manual for operating

instructions.

d. Within 60 seconds the broil burner should ignite.

Check for proper ame. Reset control to OFF.

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

To adjust lower oven air shut-

ter loosen lock screw (See

Fig. 20), reposition air shutter,

and tighten lock screw. When

nished adjusting replace

burner bae and oven bottom

panel.

Fig. 19 - oven burner locations

Air shutter

Lock screw

Oven burner

Orice hood

Fig. 20 - typical oven

burner air shutter

13. Adjust air shutter - upper

oven (some models)

The approximate ame length of the upper (broil) burner

should be 1 inch having a distinct inner, blue ame. To

determine if the upper broil burner ame is proper, set the

oven to Broil. If the ame is yellow, increase upper oven

air shutter opening size. If the ame is a distinct blue,

reduce the air shutter opening size.

To adjust the upper air shutter loosen lock screw (See

Fig. 20), reposition air shutter, and tighten lock screw.

14. Make sure range is level.

Level the range by placing a level horizontally on an oven

rack. Check diagonally from front to back, then level the

range by either adjusting the leveling legs or by placing

shims under the corners of the range as needed.

Note: After installation is complete, make sure all controls

are left in the o position.

Lower oven

bottom panel

(removable)

Lower oven

burner air

shutter

Lower oven

burner bae

(removable)

Upper oven burner

(some models)

Upper oven burner air

shutter (some models)

12. Adjust air shutter - lower

oven.

To determine if the oven burner ame is proper, remove

the oven bottom panel and lower burner bae (Refer to

Fig. 19) and set the oven to Bake at 300°F. The approx-

imate ame length of the lower oven burner should be 1

inch with a distinct inner blue ame.

To remove the lower oven bottom, remove oven bottom

hold down screws at rear of oven bottom panel. Pull up

at rear, disengage front of oven bottom from oven front

frame, and pull the oven bottom out of the oven. Remove

lower burner bae to observe oven burner ame.

If the ame is yellow in color, increase the lower oven air

shutter opening size. If the ame is a distinct blue, reduce

the air shutter opening size.

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

Filler Trim Attachment Instructions:

1. Remove the 7 screws on the vent trim on the back.

Range with ller trim installed.

2. Place the ller trim over the back by lining up the 7

screw holes of the ller trim with the vent trim and

tighten screws.

3. When ller trim is secured it will be ush with the top of

the range.

15. Install ller trim kit

Note: Installation of the ller trim kit is not required.

Disconnect electrical power to range before

beginning installation. Before servicing any part of the

appliance, make sure the appliance is o and the surfaces

are cool. Attempting to service the appliance while hot may

cause burns or other injury.

30” GAS FRONT CONTROL FREESTANDING INSTALLATION INSTRUCTIONS

16. Care, Cleaning and

Maintenance

Refer to the Use & Care Manual for cleaning instructions.

If removing the range is necessary for cleaning or

maintenance, shut o gas supply. Disconnect the gas

and electrical supply. If the gas or electrical supply is

inaccessible, lift the range slightly at the front and pull out

away from the wall. Pull out only as far as necessary to

disconnect the gas and electrical supply. Finish removing

the range for servicing and cleaning. Reinstall in reverse

order making sure to level the range and check gas

connections for leaks. Be sure to read and follow step 1 for

proper Anti-tip installation.

Some models have a cool-air intake vent on

the rear of the appliance. Do not block or obstruct this vent.

Before You Call for Service

Read the "Before You Call" and operating instruction sections

in your Use & Care Manual. It may save you time and expense.

The list includes common occurrences that are not the result

of defective workmanship or materials in this appliance.

Refer to the warranty in your Use & Care Manual for our

toll-free service number and address. Please call or write if

you have inquiries about your range product and/or need to

order parts.

17. Model and Serial Number

Location

The serial plate is located on the right-hand surface of the

oven front frame at the storage or warmer drawer; or the

lower panel area.

When ordering parts for or making inquires about your range,

always be sure to include the model and serial numbers and

a lot number or letter from the serial plate on your range.

Your serial plate also tells you the Kilowatt rating (power

requirements) and Voltage ratings.

Serial plate is located on the lower right front frame

of the appliance. Alternate location may be under

cooktop.

Serial Plate Locations:

INSTRUCTIONS D’INSTALLATION 30” CUISINIÈRE À GAZ AUTONOME

c. Serrez le raccord de l’alimentation en gaz et / ou le

conduit de l’appareil sur l’adaptateur de raccord de torche

situé sur le côté droit du régulateur de pression (voir

Fig. 10) en utilisant AU PLUS QUE 15 pi / lb. de couple.

Assurez-vous de stabiliser l’adaptateur de raccord évasé

de 1/2 ”avec une clé à molette avant de serrer le raccord

d’alimentation en gaz et / ou le conduit de l’appareil.

d. Installez l’adaptateur de raccord évasé sur la vanne

d’arrêt manuelle externe (voir g. 8).

e. Fixez le conduit exible de l’appareil à l’adaptateur de

raccord à fusée sur la vanne d’arrêt (voir g. 8).

f. Assurez-vous que la vanne d’arrêt de service du

régulateur de pression est réglée sur ON (voir g. 11).

Fig. 10

g. Vériez les fuites de gaz. Ouvrez l’alimentation en gaz

de la cuisinière et utilisez un détecteur de fuite de liquide

au niveau de tous les joints et conduits pour détecter les

fuites éventuelles dans le système.

Fig. 11

Régulateur de

pression

Vanne d’arrêt de service

(indiquée en position ON)

Vérier la pression de gaz au

collecteur

N’utilisez pas de amme pour détecter

les fuites de gaz.

Débranchez la cuisinière et son robinet d’arrêt de la

canalisation de gaz si la vérication de la pression de

l’alimentation en gaz indique une pression qui dépasse 35,6

cm (14 po) à la colonne d’eau, soit environ 3,54 kPa (1/2 lb/

po2).

L’appareil doit être isolé de la canalisation de gaz en fermant

son robinet d’arrêt manuel si la vérication de la pression

de la canalisation de gaz indique une pression égale ou

inférieure à 35,6 cm (14 po) à la colonne d’eau, soit environ

3,54 kPa

(1/2 lb/po²).

S’il s’avère nécessaire de vérier la pression de gaz au

collecteur, branchez un manomètre (hydromètre) ou un autre

appareil de vérication de pression au gicleur du brûleur de

surface arrière droit. Tenez un tuyau en caoutchouc d’environ

0,6 cm (1/4 po) de diamètre intérieur relié à l’appareil de

vérication, bien serré contre le gicleur. Ouvrez la soupape du

brûleur.

Pour obtenir une vérication précise de la pression, faites

fonctionner au moins deux (2) autres brûleurs de surface

pendant la vérication. Assurez-vous que la pression

d’alimentation en gaz (pression d’admission) est supérieure

d’au moins 2,5 cm (1 po) à la pression du collecteur.

La pression de l’alimentation en gaz ne doit jamais être

supérieure à 35,6 cm (14 po) à la colonne d’eau. La pression

au collecteur est de 10,2 cm (4 po) lorsque celle-ci est ajustée

de façon appropriée pour le gaz naturel. Pour le gaz propane/

GPL, la pression au collecteur doit être de 25,4 cm (10 po).

INSTRUCTIONS D’INSTALLATION 30” CUISINIÈRE À GAZ AUTONOME

Instructions de mise à la terre :

Le cordon d’alimentation de cet appareil est muni d’une che

à rois broches (mise à la terre) qui correspond aux prises

murales à trois alvéoles qui réduisent les risques de chocs

électriques causés par cet appareil. L’utilisateur devrait faire

vérier la prise murale et le circuit par un électricien qualié

pour s’assurer que la prise est mise à la terre et polarisée de

façon appropriée.

Ne jamais couper, enlever

ou mettre hors circuit la

broche de mise à la terre

de cette che.

Méthode recom-

mandée

Prise murale

avec mise à la

terre

Cordon

d’alimentation

muni d’une

che à trois

broches avec

mise à la terre

Fig. 12

7. Lire les consignes suivantes

sur le branchement électrique

avant de brancher la cuisinière.

Avant d’eectuer une réparation,

débranchez l’alimentation électrique au niveau du disjoncteur,

du fusible ou du cordon d’alimentation.

Exigences concernant l’électricité :

Circuit de dérivation séparé mis à la terre et polarisé correcte-

ment protégé par un disjoncteur de 15 A ou un fusible tempo-

risé. Reportez-vous à la plaque signalétique pour connaître la

tension appropriée.

Précautions à prendre concernant l’utilisation d’une rallonge :

En raison du danger potentiel que peuvent représenter les

rallonges dans certaines situations, nous déconseillons

fortement leur utilisation. Toutefois, si vous choisissez tout de

même d’utiliser une rallonge, il est absolument nécessaire

que celle-ci soit une rallonge pour électroménagers à trois

broches avec mise à la terre homologuée UL et que le

courant nominal de la rallonge soit équivalent ou supérieur au

courant nominal du circuit de dérivation. Ce type de rallonge

est disponible au service après-vente de votre région.

Veuillez lire attentivement ces

instructions! Pour des raisons de sécurité, ce produit doit être

correctement mis à la terre.

Ne coupez et ne retirez jamais, en aucune circonstance, la

troisième broche (mise à la terre) du cordon d’alimentation

(voir g. 12).

Si la prise murale ne possède que deux alvéoles, il vous revi-

ent de la faire remplacer par une prise murale à trois alvéoles

mise à la terre correctement.

8. Vérier le positionnement du

chapeau de brûleur

Il est très important de vérier que tous les chapeaux et

toutes les grilles des brûleurs de surface sont correctement

installés et se trouvent au bon endroit avant d’utiliser l’appar-

eil. La table de cuisson n’est pas amovible. N’essayez pas de

soulever ou d’enlever la table de cuisson.

Pour éviter les poussées de ammes ou la

création de sous-produits dangereux, n’utilisez pas la surface

de cuisson si les chapeaux des brûleurs ne sont pas bien in-

stallés, ceci an d’assurer un allumage adéquat et une bonne

dimension de la amme.

Laissez toujours les chapeaux et les têtes de brûleur en place

lorsque les brûleurs de surface sont utilisés. Ne laissez pas

de renversements, de nourriture, de produits de nettoyage ni

d’autres produits pénétrer dans l’ouverture du porte-gicleur.

Vériez que chaque brûleur est doté du chapeau approprié.

Vériez que tous les chapeaux de brûleur ronds sont bien

placés sur des têtes de brûleur rondes.

Vériez que tous les chapeaux de brûleur ovales sont bien

placés sur des têtes de brûleur ovales (le cas échéant). Véri-

ez que tous les chapeaux de brûleur doubles ou jumeaux

sont bien placés sur des têtes de brûleur doubles ou jumelles

(le cas échéant).

Sur les brûleurs ronds, la lèvre du chapeau du brûleur (voir

g. 13) doit s’adapter au gicleur au centre de la tête de

brûleur et être de niveau. Reportez-vous aux gures 14 et 15

pour le positionnement correct et incorrect du chapeau du

brûleur.

Vous pouvez vérier l’installation en faisant doucement glisser

latéralement le chapeau du brûleur (g. 16) pour vous assurer

qu’il est bien centré et bien assis. Le chapeau du brûleur NE

DEVRAIT PAS sortir hors du centre de la tête du brûleur lors

du déplacement latéral.

Fig. 13

Fig. 14

Positionne-

ment correct

du capuchon

du brûleur

Fig. 16

Bouchon

de bruleur

Tête de

brûleur

Allumeur

Orice

Fig. 15

Placement

incorrect du

capuchon du

brûleur

INSTRUCTIONS D’INSTALLATION 30” CUISINIÈRE À GAZ AUTONOME

Fig. 17

Dimension de la amme du brûleur

5/8”

Table de

cuisson

Fig. 18

9. Vériez l’allumage des

brûleurs de surface.

Après vous être assuré que la cuisinière et les raccords

de la conduite d’alimentation ne présentent aucune fuite,

branchez la cuisinière à l’alimentation en électricité et vériez

le fonctionnement des allumeurs électriques.

a. Pour vérier l’allumage, poussez et tournez le bouton de

l’un des brûleurs de surface dans le sens contraire des

aiguilles d’une montre et mettez-le à la position LITE

(allumage). Vous entendrez alors l’allumeur produire des

étincelles.

b. Le brûleur de surface devrait s’allumer lorsque le gaz

se rend à son niveau. Faites sortir l’air qui se trouve

dans les conduites d’alimentation en laissant le bouton

à la position LITE (allumage) jusqu’à ce que le brûleur

s’allume. Chaque brûleur devrait s’allumer en l’espace

de 4 secondes dans le cas d’un fonctionnement normal

après avoir fait sortir l’air qu’il y avait dans les conduites

d’alimentation

c. Vériez si le brûleur s’est allumé. Une fois que le brûleur

s’est allumé, le bouton de commande devrait être retiré

de la position « LITE » (allumage).

d. Essayez le bouton de chaque brûleur de surface jusqu’à

ce que ces derniers aient tous été vériés. Chaque

brûleur est muni d’une électrode distincte.

10. Régler les soupapes des

brûleurs de surface à la posi-

tion LOW (bas)(débit linéaire).

Vérier si le réglage faible « LOW » doit être ajusté :

a. Appuyez sur le bouton de commande et tournez-le à la

position

« LITE » (allumage) jusqu’à ce que le brûleur s’allume.

b. Appuyez sur le bouton de commande et tournez-le

rapidement à la position la plus basse (« LOW »).

c. Si le brûleur s’éteint, remettez le bouton à « OFF »

(arrêt).

d. Retirez le bouton de commande du brûleur de surface.

e. Insérez un tournevis à lame étroite dans la tige creuse

du robinet et tournez la vis à l’intérieur. La hauteur de la

amme peut être augmentée ou diminuée par le réglage

de cette vis. Tournez vers la gauche pour augmenter la

hauteur de la amme (g. 17 et g. 18).

f. Ajustez la amme jusqu’à ce que le bouton de

commande puisse être tourné rapidement de la position

« LITE » (Allumage) à la position la plus basse (« LOW »)

sans que la amme s’éteigne. La amme doit être aussi

petite que possible sans

s’éteindre.

Remarque :Le réglage du

mélange d’air n’est pas

requis pour les brûleurs de

surface..

11. Vérier l’allumage des

brûleurs du four.

Après avoir vérié que la cuisinière et les raccords de la

conduite d’alimentation ne présentent aucune fuite, branchez

la cuisinière à l’alimentation en électricité et vériez le

fonctionnement des allumeurs électriques. Vériez que tous

les matériaux d’emballage et la documentation ont été retirés

du four.

Le brûleur du four est muni d’un système de commande

électrique ainsi que d’un allumeur électrique. Si votre modèle

est muni d’un brûleur de four supérieur, votre appareil

est aussi équipé d’un allumeur électrique. Ces systèmes

de commande ne nécessitent aucun réglage. Lorsque le

four est prêt à fonctionner, le courant se rendra jusqu’à

l’allumeur. Celui-ci « brillera » un peu comme une ampoule.

Lorsque l’allumeur a atteint une température susante pour

permettre d’allumer le gaz, la soupape du four à commande

électrique s’ouvrira et fera apparaître une amme au niveau

du brûleur du four. Il peut s’écouler de 30 à 60 secondes

après la mise en marche du thermostat avant que la amme

apparaisse au niveau du brûleur du four. Lorsque le four

aura atteint la température désirée, l’allumeur s’éteindra.

La amme du brûleur s’éteindra dans une période allant de

20 à 30 secondes après que l’allumeur se sera arrêté. An

de maintenir la température désirée, ce cycle continuera

aussi longtemps que la commande du four sera réglée pour

fonctionner.

Pour vérier l’allumage du brûleur du four :

a. Réglez le four sur Bake (cuisson au four) à une

température de 149 ºC (300 ºF). Pour connaître les

instructions d’utilisation, reportez-vous au Guide de

l’utilisateur.

b. Le brûleur du four devrait s’allumer en l’espace de

60 secondes. Vériez la qualité de la amme, puis laissez

le brûleur eectuer un cycle. Éteignez les commandes.

c. Si votre modèle est muni d’un brûleur de gril situé à

hauteur de la taille, réglez votre four à Broil (gril). Pour

connaître les instructions d’utilisation, reportez-vous au

Guide de l’utilisateur.

d. Le brûleur du gril devrait s’allumer en l’espace de

60 secondes. Vériez la qualité de la amme. Éteignez

les commandes.

La page charge ...

Frigidaire FGGH3047VF Guide d'installation

Marque: Frigidaire

Modèle: FGGH3047VF

Catégorie: Micro-ondes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Frigidaire FGGH3047VF Installation guide
español: Frigidaire FGGH3047VF Guía de instalación

Frigidaire FGGH3047VF Guide d'installation

Frigidaire FGGH3047VF Guide d'installation

dans d''autres langues

Documents connexes

Autres documents