LevelOne FPC-0104TX Manuel utilisateur

FPC-0104TX

10/100Mbps Fast Ethernet 56K Modem

PC Card

User’s Manual

First Edition (September, 1998)

Second Edition (May, 1999)

II

Document No. M-LF560MA-rev2.0

Printed in Taiwan

-III-

FCC REGULATORY STATEMENTS

FCC Certification

10/100 Fast Ethernet + 56K Fax/Modem PC Card

FCC ID: MQ4PLM56

Made in Taiwan

The United States Federal Communication Commission (FCC) and the Canadian Department of

Communications have established certain rules governing the use of modems and other

electronic equipment.

FCC Part 68 Registration

This high speed FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card complies with

FCC Part 68 rules, and the use of this modem is subject to the following restrictions:

1. The FCC has established rules which permit this device to be directly connected to the

telephone network. Standardized jacks are used for these connections. This equipment should

not be used on party lines or coin phones.

2. If this device is malfunctioning, it may also be causing harm to the telephone network; this

device should be disconnected until the source of the problem can be determined and until

repair has been made. If this is not done, the telephone company may temporarily disconnect

service.

3. The telephone company may make changes in it's facilities, equipment, operation and

procedures; if such changes affect the compatibility or use of this device, the telephone

company is required to give adequate notice of the situation with the FCC.

4. If the telephone company requests information on what equipment is connected to their

lines, inform them of:

a. The telephone number to which this unit is connected.

b. The Ringer Equivalence Number (REN).

c. The USOC jack required.

d. The FCC Registration number.

Items (b) and (d) are indicated on the label. The Ringer Equivalence Number (REN) is used to

determine how many devices can be connected to your telephone line. In most areas, the sum of

the REN's of all the devices on any one line should not exceed 5.0. If too many devices are

attached, they may not ring properly.

FCC Part 15 Registration

This device complies with Part 15 of FCC rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interface, and

2) This device must accept any interface received, including interface that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

IV

radiate radio frequency energy, and if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning off and on, the

user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna.

(a) Increase the distance between the equipment and receiver

(b) Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

(2) Consult an experienced radio/TV technician for help.

-V-

TABLE OF CONTENTS

1. INTRODUCTION

1.1 ABOUT THIS MANUAL

1.2 ABOUT THIS PRODUCT

1.2.1 SPECIFICATIONS

1.2.2 FEATURES

1.3 SYSTEM REQUIREMENTS

1.4 CONTENTS INCLUDED IN THE PACKAGE

2. INSTALLATION

2.1 HARDWARE INSTALLATION

2.2 INSTALLING THE SOFTWARE

2.2.1 NOVELL NETWARE

2.2.2 MICROSOFT LAN MANAGER

2.2.3 PACKET DRIVER

2.2.4 WINDOWS FOR WORKGROUPS 3.11

2.2.5 WINDOWS NT 3.51 & 4.0

2.2.6 WINDOWS 95,WINDOWS 98

2.2.7 ARTISOFT LANTASTIC 6.0

3. MODEM BASICS

3.1 UNDERSTANDING AT COMMANDS

3.2 DIALING & ANSWERING TECHNIQUES

4. DRIVERS INFORMATION

4.1 NOTES for NDIS DRIVER

4.2 NOTES for PACKET DRIVER

4.3 NOTES for WINDOWS WORKGROUPS

5. QUESTIONS & ANSWERS

6. APPENDIX A: NDIS2 & ODI DRIVERS for WFW 3.11

7. APPENDIX B: UNINSTALLATION in WIN 98/95

8. APPENDIX C: AT COMMAND SET

-1-

1. INTRODUCTION

1.1. ABOUT THIS MANUAL

This manual will explain how to install and use the FPC-0104TX 10/100Mbps Fast

Ethernet 56K Modem PC Card.

1.2. ABOUT THIS PRODUCT

The FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card is a multifunction

communication device that lets you perform multiple communication tasks at the

same time:

(1) transmit and receive data up to 56,000 bps

(2) send and receive FAXes from computers or FAX machines

(3) connect to an 10/100 Fast Ethernet LAN

And it uses only one PCMCIA socket while it can provide the functions listed

above.

The FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card is a credit-card-

size Type II PCMCIA adapter that complies with the PCMCIA 2.1 and JEIDA 4.1

standards and works with computers that incorporate a compatible interface.

It is Bell, ITU-T (formerly CCITT) and Hayes AT commands compatible, allowing it

to be used worldwide with today's popular communication software programs. You

will be able to send and receive faxes with any Group 3 fax machine. Using standard

phone lines and 10/100 Fast Ethernet, the data communication functions of the

10/100 Fast Ethernet + 56K Fax/Modem PC Card will enable you to successfully

access to the servers on 10/100 Fast Ethernet LAN and hook up to the Internet,

transmit E-Mail, send and receive information and communicate with other PCs,

Bulletin Board Services (BBS) or on-line computer networks such as CompuServe

and America On line.

1.2.1. Specifications

PC Card Interface

PCMCIA Type II.

Dimension

3.37” X 2.128” X 0.197” or

85.6 mm X 54 mm X 5 mm

-2-

Weight

60 g

Power

+5V ±5%

Network

IEEE 802.3 10BaseT, 10Mbps.

IEEE 802.3u 100BaseTX, 100Mbps.

NE2000 compatible.

Modem

V.90, K56flex 56Kbps, V.34+ 33.6Kbps, V.34 28.8Kbps, V.32bis 14.4Kbps.

V.42bis/V.42, MNP 2-5 data compression and error correction.

AT command set.

Fax

Group 3, V.17 14400bps, V.29 9600bps

Fax Service Class 1 compliant.

Modem COM Port

COM2, COM3, COM4

IRQ

3, 4, 5, 7, 9, 10, 11, 12, 15

I/O Address

220, 300, 320, 340

Features

1. Compatible with most notebook computers and PCMCIA Card and Socket

Service drivers.

2. Integrated PC Card

3. Easy to install and play.

4. Support most of the popular Network Operating Systems.

5. Include popular 56K Fax/Modem communication programs.

6. Hot swappable.

7. Feature concurrent use of 10/100 Fast Ethernet LAN and 56K Fax/Modem.

8. NE2000 compatible.

1.3. SYSTEM REQUIREMENTS

• An IBM compatible PC or notebook computer with 386SX or faster processor

• At least one type II PCMCIA socket

• PCMCIA release 2.1 compliant Card Services and Socket Services

• Drivers and utilities provided with this product

• Driver software loaded on your PC

• Data and/or fax communications software.

-3-

1.4. CONTENTS INCLUDED IN THE PACKAGE

• FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card

• RJ 11 Phone Cable

• Quick Installation Guide

• Driver Diskettes for PC and Apple/Macnitosh

• Manual Diskette

• Windows-based 56K Fax/Modem application program (CD-ROM)

-4-

2. INSTALLATION

This chapter describes how to install the FPC-0104TX 10/100Mbps Fast Ethernet

56K Modem PC Card. Installation procedures also cover many popular Network

Operating Systems.

2.1. HARDWARE INSTALLATION

1. Hold the card label up and insert the card into the computer's PCMCIA slot

with the 68 pin connector facing the computer.

2. Connect the RJ-45 (8-pin) plug to the LAN and the RJ-11 (6-pin) plug to the

telephone wall outlet.

2.2. INSTALLING THE SOFTWARE

For Non-Windows 95/98 & Non-Windows NT System

Plug the driver diskette into the floppy drive and set the current drive to the floppy

drive (A:\). Then run INSTALL to install the dirver.

-5-

2.2.1. Novell Netware Installation

Follow the steps bellow to complete the Novell Netware installations.

1.Run installation program INSTALL.EXE in the driver disk (for example,

A:\INSTALL).

2.Select Netware 3.x and 4.x Workstation in the installation program dialog box.

3.Check the card settings. If current settings are correct, select Start Installation

and go to step 5. Otherwise, select Modify Parameters to change settings.

4.Select the appropriate values then press Enter. When you are finished, press OK

to exit.

5.Installation program starts installing drivers and modifying AUTOEXEC.BAT and

NET.CFG. Select Yes then press Enter to modify the files.

6. Now, the installation is completed.

7. Restart your computer to make Netware connections.

To install the ODI driver manually, follow the instructions below:

1.Copy the file

\NETWARE\LM28ODI.COM \NETWARE\NET.CFG

-6-

and the file

\ENABLER\CARDEN.EXE \ENABLER\LMVXD.386

from the driver disk to your local hard disk.

2.Using text editor to edit the NET.CFG for setting the frame type. The frame type

default is set to 802.3 for Netware 3.11 server and 802.2 for Netware 3.12 and 4.x

servers. The frame type set in NET.CFG must match that set in Netware servers.

3.Using following format to create a startup batch file

CARDEN /IOP=nnn /IRQ=nnn /COM=n /MIR=n

LSL ;Link Support Layer Module

;provided by Novell

LM28ODI ;Hardware Specific Module

IPXODI ;IPX Protocol Stack Module

;provided by Novell

NETx ;Shell Support Module provided by

;Novell

LOGIN

2.2.2. MS LAN Manager Installation

1.Cast a look at the README.TXT in the \NDIS2 directory in the driver disk. Before

installing the drivers, please ensure that the Microsoft LAN Manager has been

installed in the target path. The installation program will check and modify the

PROTOCOL.INI file for LAN Manager.

2.Run INSTALL.EXE in the root of driver diskette (A:\INSTALL).

3.Select Microsoft LAN Manager from the menu screen.

4.Check the card settings. If current settings are correct, select Start Installation

and go to step 5. Otherwise, select Modify Parameters to change settings.

5.Select the appropriate values then press Enter. When you are finished, press OK

to exit.

6.Installation program starts installing drivers and

modifying CONFIG.SYS and PROTOCOL.INI

Select Yes then press Enter to modify the files.

7.Now, the installation is completed.

8.Reboot the computer to load driver and start LAN Manager.

Example of PROTOCOL.INI:

[PROTMAN]

DRIVERNAME = PROTMAN$

DYNAMIC = YES

PRIORITY = NETBEUI

[NETBEUI_XIF]

-7-

Drivername = netbeui$

SESSIONS = 6

NCBS = 12

BINDINGS = "LMNDIS_NIF"

LANABASE = 0

[LMNDIS_NIF]

; protocol.ini session for multifunction

LAN/MODEM driver.

IOADDRESS = 0x320

INTERRUPT = 11

DRIVERNAME = LMNDIS$

2.2.3. Packet Driver Installation

1.Run INSTALL.EXE file in the driver diskette (A:\INSTALL).

2.Select Packet Driver from the menu screen.

3.Check the card settings. If current settings are correct, select Start Installation

and go to step 5. Otherwise, select Modify Parameters to change settings.

4.Select the appropriate values then press Enter. When you are finished, press OK

to exit.

5.Installation program starts installing drivers and

modifying AUTOEXEC.BAT. Select Yes then

press Enter to modify the files.

6.Now, the installation is completed.

7.Reboot the computer to load driver.

2.2.4. Windows for Workgroups 3.11 Installation

1. Run INSTALL.EXE in root directory on the driver disk.

2. Select Windows for Workgroup in Network Operating System screen.

3. If current settings are accepted, select Start Installation and go to step 13.

Otherwise, select Modify Parameters to make modifications.

4. Move cursor to the setting you want to make a change for then press Enter to

select a fit value. When the configuration is accepted, press Enter

on the OK field to exit the screen and go back to step 3.

5. Select NDIS Server (LAN Manager,...) as the network server that you will

attach to then press Enter.

6. Installation program starts installing drivers and modifying ATOEXEC.BAT.

Select Yes then press Enter to modify the files.

7. Run Windows for Workgroups and click Network Setup icon in Network

group.

8. In Network Settings dialog box, click Networks... button to select the network

operating system.

-8-

9. In Networks dialog box, check the radio button before Install Microsoft

Windows Network and No Additional Network. Press OK to go back the

Network Settings screen.

10. Click Drivers... button to select network driver.

11. From Network Drivers dialog box, press Add Adapter... button to enter Add

Network Adapter dialog box. Select Unlisted or Updated Network Adapter and

press OK.

12. Windows will prompt a Install Driver dialog box; put the driver diskette into

floppy drive then press OK.

13. Select Enhanced mode NDIS3 for.... then press OK.

14. Follow Windows instructions to complete the installation and exit Windows

15. Reboot the computer to run with WFW 3.11.

2.2.5. Windows NT 3.51 & NT 4.0 Installation

Getting Start for Windows NT3.51

1. Run Windows NT 3.51

2. Login with a full access level , i.e. ADMINISTRATOR

3. Remove all existing network support

-- open Program Manager à Main group à Control Panel à Network

-- remove all existing network components

Note: remove all adapters first, then servers, then workstations, etc.

4. Remove all serial port support

-- open Program Manager à Main group à Control Panel à Ports

-- remove all the COM port devices

Note: If problems occur during removing the COM ports, check if the NT has

been updated to the lastest release from Microsoft.

-- after all serial port devices are removed, press Close

Add PCMCIA to Your Laptop

1. Open Program Manager à Main group à Control Panel à Devices

2. Select PCMCIA

3. Press STARTUP

4. Select BOOT, then press OK

5. When all PCMCIA adapters are added, press Close and restart Windows NT

Check Event Viewer when system reboots. Ask your laptop dealer for help if any

problems occur during the pre-installation.

-9-

Installation in NT 3.51

1. Insert the FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card into one

of the PCMCIA slots

2. Run Windows NT

3. Login with a full access level i.e. ADMINISTRATOR

4. Open Program Manager à Main group à Control Panel à Network

5. Press YES to install network components

6. Enter the correct path for NT installation media (CD-ROM). For example, D:\i386.

7. Press ”Do not detect for the network adapter”

8. Open the Network Adapter Card selection box

9. Select <OTHER> REQUIRES DISK FROM MANUFACTURER

10. Click CONTINUE button

11. Insert the driver disk into floppy disk drive, then enter the correct path (A:\).

12. Take a choice for the 10/100 Fast Ethernet + 56K Fax/Modem PC Card then

press OK.

13. A dialog box will be poped up for the driver settings change.

14. Give appropriate system resources to the your DirectPort PC Card, the settings

must be unique for this device. Resources Recommendation

I/O Base I/O:300. Possible alternative: 220,

320, 340

Interrupt (IRQ) IRQ:5. If your laptop is equipped

with multimedia devices, a higher

interrupt (IRQ:11) may be needed.

Base Memory D000. Possible alternative: D800

COM Port COM2 to COM4. Select one of

the COM port that is not in use

by other communication devices.

15. When all settings are completed, press OK Windows NT will load network and

grant configurations for

-NWLink

-TCP/IP

-Netbeui

Typically the configurations are unique for each network. Ask your network

administrator for help if you want to change them.

16. Once all network softwares are well loaded, press OK. The configuration and

bindings for the PC Card might be confirmed. Answer the questions

accordingly.

17. Connect to your network using the provided 10/100 Fast Ethernet RJ-45 jack.

-10-

18. Reboot the system.

Getting Start for Windows NT4.0

1. Remove all existing PC Cards from the system.

2. Run Windows NT 4.0

3. Login with a full access level i.e. ADMINISTRATOR

4. Remove all existing network support from

MY COMPUTER à CONTROL PANEL à NETWORK à ADAPTERS

5. Press CLOSE after all network components are removed.

6. Remove all serial port devices in

MY COMPUTER à CONTROL PANEL à PORTS

7. Press CLOSE after all serial port devices are removed.

Installation in NT 4.0

1. Insert your DirectPort PC Card into one of the PCMCIA Slots

2. Start Windows NT 4.0

3. Login with a full access level ADMINISTRATOR

4. Open MY COMPUTER à CONTROL PANEL à NETWORK.

If Network has not been installed,

♦ select YES to start Network installation,

♦ press Next and press SELECT FROM LIST button, then press HAVE DISK

button,

♦ insert the driver disk into drive floppy disk drive, then enter the correct path.

♦ select the only one choice for the 10/100 Fast Ethernet + 56K Fax/Modem PC

Card, then press OK and NEXT

♦ Windows NT 4.0 will grant configurations for

-- TCP/IP

-- NWLink IPX/SPX

-- NetBEUI

...

These configurations are unique for each network. If you want to change them,

ask your

network administrator for help.

♦ Press Next twice to use default NETWORK SERVICES settings

♦ Enter the correct path for NT 4.0 system source files.

♦ A dialog box will pop up. Give appropriate system resources to the DirectPort

PC Card; the settings must be unique for this device. Refer to resources

Recommendation” for NT 3.51 details

♦ Press NEXT twice. Enter COMPUTER NAME then press NEXT

♦ Press FINISH

-11-

If Network has been installed

♦ Select ADAPTERS

♦ Press ADD to add network adapters

♦ Press HAVE DISK button

♦ Insert your DirectPort PC Card driver disk into floppy disk drive

♦ Enter the correct path for Windows NT 4.0 drivers then press OK.

♦ A dialog box will pop up. Give appropriate system resources to the DirectPort

PC Card; the settings must be unique for this device. Refer to ”Resources

Recommendation” for NT 3.51 details

♦ Press OK when all setting are completed.

♦ Press CLOSE to complete NETWORK setting

♦ Reboot Windows NT.

Modem configuration for NT 4.0

1. Open MY COMPUTER à CONTROL PANEL à MODEMS

2. Using default settings and press NEXT

3. System should have detected your LANmodem PC Card, and enter the Modem

Manufactures & Models list screen.

4. Press FINISH and then CLOSE to complete modem setting.

5. Reboot the system.

6. The installations for both LAN and Modem are completed.

2.2.6. Windows 98/95 Installation

1.Assume that the PCMCIA card reader and drivers have been loaded and well

functioning. The System Icon in the Control Panel can report on its functionality.

If not, check your computer dealer for technical support.

2.Insert your Integrated PC Card into PCMCIA slot. Windows 95/98 will prompt

New Hardware Found dialog box. In New Hardware Found dialog box, select

Driver from disk provided by hardware manufacturer.

-12-

3.Enter the correct path, i.e. ? :\”, then insert the driver disk. The driver will be

installed automatically, and system may ask for the Windows 95/98 installation

CD/disks to update the existing files or drivers. After the update, system will

reboot automatically.

4.For the first time installation, click Network icon in Control Panel to correctly add

Protocols, Client and Service according to your application requirements.

5.Reboot the machine and the card will fully function.

2.2.7. Artisoft Lantastic 6.0 Installation

1.Install LANTASTIC 6.0 first.

2.Run INSTALL.EXE in the driver disk root directory.

3.Select LANTASTIC 6.0 in Network Operating System screen then enter Driver

Install screen.

4.If current settings are correct, select Start Installation and go to step 6.

Otherwise, select Modify Parameters to make changes.

5.Move cursor to each field you want to make modification and press Enter to set

correct value. Then press Enter on the OK.

6.Installation program starts copying drivers and modifying CONFIG.SYS,

PROTOCOL.INI, and STARTNET.BAT.

7.Reboot the computer to have the driver take effect.

-13-

3. MODEM BASICS

This chapter covers the basic commands and techniques involved in modem

operation. In many cases, this is the only information you will need in order to get

the FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card up and running

with communication software, and to start making connections with your PC Card.

3.1 Understanding AT Commands

The FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card communicates

asynchronously with computers using AT commands. AT commands are used to

configure and control the PC Card. Commands are usually sent to the modem in way

of communication software, but can also be entered manually with the computer

keyboard.

Command statements must be written in a specific form in order for the

FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card to recognize them. A

command statement always begins with the letters AT or at. It is then followed by

one or more commands and the <Enter> key.

AT commands can only be issued when the FPC-0104TX 10/100Mbps Fast Ethernet

56K Modem PC Card is in ”Command mode” or ”off-line.” Once the PC Card has

established a connection with another modem, it is said to be ”on-line” or in ”Data

mode.” In this mode, the characters sent to the Ethenet + 56K Fax/Modem PC Card

by your computer are transmitted to the remote modem rather than being interpreted

by the PC Card as commands.

Using the Windows 95/98 Hyper Terminal Program to issue an AT command

statement, you first need to run a communication program such as the Microsoft

Windows ”Hyper Terminal” program. This program provides a simple method to

manually enter AT commands so you can do things such as: store phone numbers

you commonly connect to.

Once the FPC-0104TX 10/100Mbps Fast Ethernet 56K Modem PC Card is connected

to your computer serial port and telephone line, open the Windows 95/98

”Accessories” program group, and open the Hyper Terminal Program. The program

will prompt you for a name and icon to use for your new connection. Type the name

Test Connection then press <Enter>.

Next, you will be prompted for country information, area code, phone number, and

the device used to make the connection. For this test purpose, do not enter a phone

number; simply choose the COM port your Integrated is connected to from the

”Connect Using” list. Click ”OK” when finished.

-14-

The next window sets the COM port settings. The settings used for the Comet

should be as follows:

Bits per second: 115200

Data bits: 8

Parity: None

Stop bits: 1

Flow Control: Hardware

Click ”OK” when finished. After you have done this, save your new connection by

selecting ”Save” from the ”File” menu then click ”OK.” A new connection icon will

be added to your Hyper Terminal folder.

You are now ready to start entering AT commands.

In the terminal window, type:

AT<Enter>

LANmodem responds

OK

This confirms that the modem and your computer are communicating correctly.

To test the telephone line connection, issue the manual answer command. Type:

ATA<Enter>

The LANmodem will pick up the phone line, and try to communicate. Normally, this

command is only used to answer an incoming call made from another modem. Thus

the high pitched noise you will hear from the speaker. To abort the operation, press

any key, or select ”Disconnect” from the menu.

3.2 Dialing and Answering Techniques

Depending on what communications software you use to make modem

connections, you may not have much control of how the modem dials the

telephone number. This section shows some useful examples of the AT commands

used for dialing and answering operations. The command characters specific to

each function are shown in bold type.

Dialing using the ATD Command

Touch Tone Dialing: ATDT 555 1212

Pulse Dialing: ATDP 555 1212

Tone and Pulse Dialing: ATDP 555 1212 WT 24

Pause During Dialing: ATDT 9,,555 1212

La page charge ...

LevelOne FPC-0104TX Manuel utilisateur

LevelOne FPC-0104TX Manuel utilisateur

dans d''autres langues

Autres documents