JennAir JXD7030YS Le manuel du propriétaire

Marque: JennAir

Modèle: JXD7030YS

Taper: Le manuel du propriétaire

Ce manuel convient également à

LI3ZVD/W10342490G

30" (76.2 CM) AND 36" (91.4 CM)

RETRACTABLE (POP-UP) DOWNDRAFT

VENT SYSTEM

SYSTÈME DE VENTILATION RÉTRACTABLE

(CLAPET) DE 30" (76,2 CM) ET 36" (91,4 CM) -

ASPIRATION PAR LE BAS

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou dépannage, composer le :

1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à www.jennair.com.

Au Canada, composer le : 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à www.jennair.ca.

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

TABLE OF CONTENTS TABLE DES MATIÈRES

VENT SYSTEM SAFETY.................................................................3

INSTALLATION REQUIREMENTS ................................................. 5

Tools and Parts .............................................................................5

Location Requirements ................................................................5

Electrical Requirements ...............................................................8

Venting Requirements ..................................................................8

INSTALLATION INSTRUCTIONS ................................................... 9

Venting Methods ..........................................................................9

Install Vent System .....................................................................10

Rear Mounting — Blower Motor ................................................12

Complete Installation .................................................................14

Make Electrical Connections .....................................................16

Check Operation ........................................................................16

VENT SYSTEM USE .....................................................................17

Operating Downdraft Vent .........................................................17

VENT SYSTEM CARE ..................................................................17

Surface of Downdraft Vent ......................................................... 17

Filters ..........................................................................................17

TROUBLESHOOTING ..................................................................18

WIRING DIAGRAM .......................................................................19

ASSISTANCE OR SERVICE .........................................................20

In the U.S.A. ...............................................................................20

In Canada ...................................................................................20

Accessories ................................................................................20

WARRANTY ..................................................................................21

SÉCURITÉ DU SYSTÈME DE VENTILATION .............................22

EXIGENCES D'INSTALLATION ...................................................24

Outils et pièces ...........................................................................24

Exigences d’emplacement .........................................................24

Spéciﬁcations électriques ..........................................................27

Exigences concernant l'évacuation ...........................................27

INSTRUCTIONS D'INSTALLATION .............................................28

Méthodes d’évacuation .............................................................28

Installation du conduit d’évacuation ..........................................29

Montage du ventilateur à l'arrière ..............................................31

Achever l’installation ..................................................................33

Raccordements électriques .......................................................35

Contrôle du fonctionnement ......................................................35

UTILISATION DU SYSTÈME D’EXTRACTION ...........................36

Utilisation du système d’extraction par le bas ..........................36

ENTRETIEN DU SYSTÈME D’ÉVACUATION .............................37

Surface du système d’extraction par le bas ..............................37

Filtres ..........................................................................................37

DÉPANNAGE .................................................................................38

SCHÉMA DE CÂBLAGE ...............................................................39

ASSISTANCE OU SERVICE .........................................................40

Aux É.-U. ....................................................................................40

Au Canada ..................................................................................40

Accessoires ................................................................................40

GARANTIE .....................................................................................41

VENT SYSTEM SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTA NT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools Needed

■ Jigsaw or keyhole saw

■ Drill

■

" (3 mm) drill bit for pilot holes

■ Pencil

■ Tape measure or ruler

■ Flat-blade screwdriver

■ Phillips screwdriver

■

" (9.5 mm) nut driver

■ Level

■ Pliers

■ Metal snips

■ Wire stripper or utility knife

■ Caulking gun and weatherproof caulking compound

Parts Supplied

■ Top trim – stainless

■ End caps (2)

■ Lower support legs (2)

■ Undercounter mounting brackets (2)

■ 4 x 8 mm screws (16)

■ 3.5 x 9.5 mm screws (3)

■ 3

" x 10" (8.3 cm x 25.4 cm) rectangular damper

■ 4

" (12.0 cm) motor box

■ ¼" (6.4 mm) deep cover

■ Flat vent cover plate

■ 6" (15.2 cm) diameter vent transition with damper

Parts Needed

■ UL listed or CSA approved ½" (12.7 mm) conduit connector

■ Wall or roof cap with damper to match vent system

■ Vent system

■ Home power supply cable

■ UL listed wire connectors (3)

■ Vent clamps/duct tape as required

Location Requirements

NOTE: Downdraft vent is installed directly behind the cooktop.

Install the downdraft vent ﬁrst, and then install the cooktop.

IMPORTANT: Observe all governing codes and ordinances.

■ Have a qualiﬁed technician install the downdraft vent. It

is the installer’s responsibility to comply with installation

clearances speciﬁed on the model/serial/rating plate. The

model/serial/rating plate is located on the front of the

downdraft vent above the terminal box cover.

■ Downdraft vent location should be away from strong draft

areas, such as windows, doors, and strong heating vents

or fans.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

■ Consult the cooktop manufacturer installation instructions

before making any cutouts.

Check that the downdraft vent and cooktop location will

clear the cabinet walls, backsplash, and rear wall studs

inside the cabinet.

Check for the minimum distance between the front edge

of the countertop and the front edge of the cooktop. The

minimum horizontal distance between the overhead cabinets

is the same as the width of the installed downdraft vent.

■ All openings in ceiling and wall where the downdraft vent

will be installed must be sealed.

■ Grounded electrical outlet is required. See the “Electrical

Requirements” section.

■ When installing the downdraft vent, the cabinet drawer

will need to be removed and the drawer front installed

permanently to the cabinet.

Cabinet Construction:

Downdraft vent is designed for use in a cabinet with a depth of

24" (61 cm). Some installations require a countertop deeper than

25" (63.5 cm). See the “Countertop Cutout Dimensions” section.

The maximum depth of the overhead cabinet is 13" (33 cm).

Overhead cabinets installed at either side of the downdraft vent

must be 18" (45.7 cm) above the cooking surface.

For Mobile Home Installations

The installation of this downdraft vent must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities

and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with

local codes.

Product Dimensions

As-Received Blower

Reversed Blower

10" (25.4 cm)

4³⁄₄"

(12 cm)

16¹⁵⁄₁₆" (43 cm)

10"

(25.4 cm)

Front of

Range Hood

Front of

Range Hood

Top trim widths:

30" (76.2 cm)

36" (91.4 cm)

13¹⁄₂" (34.3 cm)

retractable

vent height

27" (68.6 cm) for 30" (76.2 cm) vent

33" (83.8 cm) for 36" (91.4 cm) vent

16¹⁄₂" (42.0 cm)

10"

(25.4 cm)

2¹⁄₈" (5.4 cm)

28¹⁄₂"

(72.4 cm)

³⁄₈" (0.95 cm)

1¹⁄₂" (3.8 cm)

13¹⁄₈" (33.4 cm)

5¹⁄₄"(13.3 cm)

for 30" (76.2 cm) vent

8¹⁄₄" (21.0 cm)

for 36" (91.4 cm) vent

³⁄₄"

(1.9 cm)

Cabinet Dimensions

NOTES:

■ See cooktop manufacturer’s instructions for cooktop cutout

depth and width.

■ Use dimensions for vent system cutout location that applies

to your installation.

■ Interior-mounted blower systems connect with 3

" x 10"

(8.3 cm x 25.4 cm) rectangular or 6" (15.2 cm) round vent

system. The cutout locations for this vent system will

depend on your speciﬁc installation.

Countertop Cutout Dimensions

IMPORTANT: Countertops with a bull-nosed front edge are not

recommended for these installations.

Some models require a countertop deeper than 25" (63.5 cm);

see the following illustrations.

To avoid mistakes, it is recommended that the cooktop and vent

cutouts be drawn on the countertop before making any cutouts.

See the Installation Instructions that came with your cooktop

for complete cutout dimensions, location dimensions, and

installation details.

A. Downdraft vent

B. Cooktop

C. Measurement of cooktop rear

overhang

D. D = Measurement of cooktop rear

overhang (C) + 1

" (46.2 mm) (E)

E. 1

" (46.2 mm)

F. ½" (12.7 mm) minimum

G. ¼" (6.4 mm) minimum

H. Countertop and backsplash

I. ½" (12.7 mm) minimum

A. ½" (12.7 mm) minimum to

backsplash or rear wall

" (19.1 mm) maximum

backsplash depth

C. 27

" (69.9 cm) on 30" (76.2 cm)

models

" (85.9 cm) on 36" (91.4 cm)

models

D. D = E + 1

" (46.2 mm)

E. Cooktop rear overhang

A = ¹⁄₂" (12.7 mm)

minimum

21⁵⁄₁₆"

(54.1 cm)

Cutouts are

for 3¹⁄₄" x 10"

(8.3 cm x 25.4 cm)

rectangular or 6"

(15.2 cm) round

vent system.

Centerline of cooktop cutout

21⁵⁄₁₆"

(54.1 cm)

Locate power

supply junction

box at lower

left-hand

rear corner

of the cabinet.

10" (25.4 cm)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition) or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical

circuit is required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate.

The model/serial/rating plate is located on the front of the

downdraft vent above the wiring box cover.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition) or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Venting Requirements

IMPORTANT: Make sure there is proper clearance within the wall

or ﬂoor before making exhaust vent cutouts.

■ Use heavy (rigid) metal vent.

■ Venting system must terminate to the outside.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Do not install 2 elbows together.

■ Do not use plastic or metal foil vent.

■ The length of vent system and number of elbows should

be kept to a minimum to provide efﬁcient performance.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

■ Use clamps or duct tape to seal all joints in the vent system.

■ Use caulking tape to seal the exterior wall or ﬂoor opening

around cap.

■ Do not cut joist or stud. If vent cutout falls over a joist

or stud, a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate

each foot of ﬂexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended vent system length:

For either interior-mounted or exterior-mounted blower

installations, the vent system length should not exceed the

maximum lengths listed in the “Maximum Length of Vent

System” chart. See “Calculating Vent System Length” in the

“Venting Methods” section in the Installation Instructions.

Cold Weather Installations

An additional backdraft damper should be installed to minimize

backward cold airﬂow and a thermal break should be installed

to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the

thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than speciﬁed CFM of

air movement. The speciﬁed CFM varies from locale to locale.

Consult your HVAC professional for speciﬁc requirements in

your area.

INSTALLATION INSTRUCTIONS

Venting Methods

Determine which venting method is best for your application.

Vent system can terminate either through the wall or ﬂoor.

Island Location

NOTE: For island locations, a front- or rear-mounted blower

motor can also be mounted for right or left venting if needed for

your application. Most island applications would still require the

venting to be directed down through the ﬂoor.

Built-In Cabinet Location

Front-Mounted Blower

Motor (Standard)

Rear-Mounted Blower Motor

A. Down vent

B. Left vent

C. Right vent

Island Location — Vent System Installed Under

a Concrete Slab Using PVC Sewer Pipe

Front-Mounted Blower Motor (Standard)

Rear-Mounted Blower Motor

Calculating Vent System Length

3¼" x 10" (8.3 cm x 25.4 cm) rectangular vent is required from

the blower motor box. It can be transitioned to 6" (15.2 cm)

round vent if needed.

Maximum Length of Vent System

Vent Length

6" (15.2 cm) round 35 ft (8.9 m)

" x 10" (8.3 cm x 25.4 cm) 35 ft (8.9 m)

A. Wall cap

B. 6" (15.2 cm) round metal vent

C. 16" (40.6 cm) maximum

D. 6" (15.2 cm) round PVC sewer pipe

E. 6" (15.2 cm) round metal vent transition with damper (supplied)

F. 6" (15.2 cm) round PVC coupling

G. Concrete slab

H. 6" (15.2 cm) round PVC sewer pipe

I. 6" (15.2 cm) round 90° PVC sewer pipe elbow

J. Tightly pack gravel or sand completely around pipe.

K. 6" (15.2 cm) round 90° PVC sewer pipe elbow

L. 6" (15.2 cm) round PVC coupling

M. 12" (30.5 cm) minimum

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece

" x 10" (8.3 cm x 25.4 cm)

Rectangular

" x 10" (8.3 cm x 25.4 cm)

90° elbow

5.0 ft

(1.5 m)

" x 10" (8.3 cm x 25.4 cm)

ﬂat elbow

12.0 ft

(3.7 m)

" x 10" (8.3 cm x 25.4 cm)

wall cap

0.0 ft

(0.0 m)

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

6" (15.2 cm) wall cap 0.0 ft

(0.0 m)

" x 10" (8.3 cm x 25.4 cm)

to 6" (15.2 cm) transition

4.5 ft

(1.4 m)

6" (15.2 cm) to 3

" x 10"

(8.3 cm x 25.4 cm) transition

1 ft

(0.3 m)

" x 10" (8.3 cm x 25.4 cm)

to 6" (15.2 cm) 90° elbow

transition

5.0 ft

(1.5 m)

6" (15.2 cm) to 3

" x 10"

(8.3 cm x 25.4 cm) 90° elbow

transition

5.0 ft

(1.5 m)

Example Vent System

The following example falls within the maximum vent length

of 35 ft (8.9 m).

2 - 90° elbow = 10.0 ft (3 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Transition = 4.5 ft (1.4 m)

Length of 6" (15.2 cm) or 3

" x 10"

(8.3 cm x 25.4 cm) system

= 22.5 ft (6.8 m)

Install Vent System

1. Place cardboard or similar material on top of a ﬂat surface

where you can easily assemble the downdraft vent system.

2. Remove parts packages, downdraft vent, and blower box

from the carton.

3. Remove all shipping materials, tape, and ﬁlm from the

downdraft vent and blower box.

4. Measure distance “X” from the cabinet ﬂoor to the top of the

countertop. Subtract 28

" (72.4 cm) from distance “X” to

determine dimension “Y” (X - 28

" = Y).

6 ft

(1.8 m)

2 ft (0.6 m)

A. Blower motor

B. Transition

C. 90° elbows

D. Backdraft damper

WARNING

Excessive Weight Hazard

Use two or more people to move and install

downdraft vent.

Failure to do so can result in back or other injury.

Cabinet floor

Top of countertop

Downdraft vent

“X”

“Y”

28¹⁄₂"

(73 cm)

5. Attach the support legs to the side of the vent box with

4 - 4 x 8 mm screws in each support leg. Adjust to dimension

“Y” from the bottom of the vent box to the bottom of the

support legs. Tighten screws.

Determine Which Vent Direction Is Best for

Your Installation

When installed in a cabinet, vent system can exhaust through

the bottom, left, or right of the cabinet.

IMPORTANT: When using the 6" (15.2 cm) vent transition

(supplied) for 6" round venting, only left or right venting is

recommended.

Bottom Venting:

NOTE: If installing the vent damper in the down position, a wall

or roof cap with a damper at the exit end of the vent system

is required.

■ Downdraft vent is shipped with blower in down-venting

position, so no modiﬁcation is required.

■ If rear mounting of the blower motor is not required, go

to the “Complete Installation” section.

■ To mount the blower motor to the rear side of the vent box,

go to the “Rear Mounting — Blower Motor” section.

Dim.

“Y”

A. Motor box

B. Support leg

C. 4 x 8 mm screws (4)

Left or Right Venting:

1. Using 2 or more people, place the downdraft vent system

on its back.

2. Remove the 4 screws from the cover plate mounted to the

face of the motor box and set them aside.

3. Slide the cover plate up and slip it over the keyhole slot

shoulder screws. Set the cover aside.

4. Remove 4 screws from the bottom of the motor box that

hold the motor assembly to the motor box.

NOTE: Disconnect the electrical wiring connection from

motor if needed.

5. Remove 3 screws and the vent cover plate from the left

or right side of the motor box for the venting direction to

be used.

6. Rotate the blower motor assembly 90° to the left or right side

to the chosen venting direction and secure to the blower box

with motor mounting screws previously removed. Do not

twist or bind the wires.

7. Install the vent cover plate over the rectangular opening in the

bottom of the motor box and secure with vent cover screws.

NOTE: Reinstall the electrical wiring connection to motor

if removed.

8. Reinstall the cover plate to the face of the motor box and

secure with 4 cover plate screws previously removed.

9. For mounting the blower motor to the back of the vent

box, go to the “Rear Mounting — Blower Motor” section.

Otherwise, go to the “Complete Installation” section.

A. Cover plate

B. Cover plate screws (4)

C. Cover plate keyhole slot

shoulder screws (4)

D. Motor mounting screws (4)

E. Vent cover plate

F. Motor box

G. Vent cover screws (3)

Rear Mounting — Blower Motor

NOTE: Optional blower motor rear-mounting position

(opposite side) for island cabinet location. The blower motor

box assembly can be moved to the opposite side (rear)

of the vent box.

1. Remove 7 screws from the mounting ﬂanges of the blower

motor box.

Front View

2. Lift blower motor box off the shoulder screws in the keyhole

slots. Disconnect wire connection from blower motor and set

blower motor box aside.

3. Remove 6 screws from the mounting ﬂange of the ¼" (6.4 mm)

deep cover.

A. Screws (7)

B. Keyhole slot shoulder screws (2)

C. Blower motor box

A. Blower motor box

Rear View

4. Lift the ¼" (6.4 mm) deep cover off the shoulder screws

in the keyhole slots and set the cover aside.

5. Remove the screws from the wire-mounting plate.

A. Screws (6)

B. Keyhole slot shoulder screws (2)

" (6.4 mm) deep cover

A. Deep cover

A. Screws

B. Wire-mounting plate

C. Blower motor box

6. Hold the wire-mounting plate and push the grommet out

of the wire-mounting plate.

7. Slide the wire assembly through the slot in the wire-mounting

plate to remove it.

8. Place the wire assembly through the opening to the opposite

side of the vent box.

9. Reassemble the wire assembly and grommet to the wire-

mounting plate.

10. Install the wire-mounting plate to the vent box using the

4 screws previously removed.

11. Place the blower motor box assembly with the keyhole slots

over the 2 shoulder screws on the rear of the vent box and

reconnect the wire connection to the blower motor.

12. Mount the blower motor box to the vent box and secure

using the 6 screws previously removed.

13. Mount the 4

" (12.0 cm) cover box (supplied) to the front

of the vent box. Place the keyhole slots over the 2 shoulder

screws, align the mounting holes, and secure the cover box

to vent box using the 6 screws previously removed from the

¼" (6.4 mm) deep cover.

A. Wire-mounting plate

B. Grommet

14. Remove the front cover from the deep cover, place the front

cover over the previously mounted cover box, and secure

using the 4 screws previously removed.

15. Go to the “Complete Installation” section.

A. Deep cover

B. Front cover

C. Cover box (supplied)

Complete Installation

NOTE: The downdraft vent system is supplied with a 3

" x 10"

(8.3 cm x 25.4 cm) backdraft damper and a 6" (15.2 cm) round

vent transition with damper. Refer to “3

" x 10" (8.3 cm x

25.4 cm) Backdraft Damper” or “6" (15.2 cm) Round Vent

Transition with Damper,” depending upon the type of venting

you are using.

" x 10" (8.3 cm x 25.4 cm) Backdraft Damper

1. Attach the 3¼" x 10" (8.3 cm x 25.4 cm) backdraft damper

to the vent opening in the blower motor box, using three

3.5 x 9.5 mm screws.

6" (15.2 cm) Round Vent Transition with Damper

1. Attach the 6" (15.2 cm) round vent transition to vent opening

(left- or right-side venting only is recommended), using two

3.5 x 9.5 mm screws.

A. 3.5 x 9.5 mm screws

B. 3¼" x 10" (8.3 cm x 25.4 cm) backdraft damper

A. 3.5 x 9.5 mm screws

B. 6" (15.2 cm) round vent transition with damper

2. Remove 4 screws attaching the terminal box cover.

3. Determine which direction (front or rear) the home power

supply cable will enter the terminal box. Remove the

appropriate knockout from the front or rear panel and install a

" (12.7 mm) UL listed or CSA approved conduit connector.

4. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Position downdraft vent so it is centered

in the cutout with the rear ﬂange over the edge of the cutout

and the rear of the vent box against the edge of the cutout.

A. Terminal box cover

A. Rear ﬂange of downdraft vent

B. Edge of cutout in countertop

C. Rear of downdraft vent

D. Cabinet back

E. Lower support leg

F. Cabinet ﬂoor

G. Countertop

5. Install the left and right undercounter mounting brackets to

the vent box. Slide the keyhole slots over the guide tabs and

push the brackets up to set them in place.

6. Drill 2 pilot holes through each of the undercounter mounting

brackets into the underside of the countertop. Using 2 screws

(not provided) of the appropriate length, mount the brackets to

the countertop.

IMPORTANT: Select a screw length that will not allow the

screws to go through the countertop when tightened.

A. Vent box

B. Undercounter mounting bracket

C. Keyhole slots

D. Guide tabs

A. Screws

B. Backsplash

C. Countertop

7. Check that the downdraft vent is level as shown below.

Loosen the lower support leg screws and position the legs

against the cabinet ﬂoor.

8. Fasten the lower support legs to the cabinet ﬂoor with

screws (not provided).

9. Tighten the lower support legs screws.

10. Attach the left and right end caps to the vent box. Place the

tab into the mounting slot at each end of the downdraft vent,

as shown, and push down to lock into place.

A. Downdraft

B. Level

A. Screw (not provided)

A. End cap tab

B. Mounting slot

Make Electrical Connections

1. Disconnect power.

2. Feed the power supply cable through the conduit connector

and into the terminal box.

3. Connect the green (or green/yellow) ground wire to the green

or yellow/green ground wire using UL listed wire connectors.

Tighten the screw on the conduit connector.

4. Connect the 2 white wires together using UL listed wire

connectors.

5. Connect the 2 black wires together using UL listed wire

connectors.

6. Replace the terminal box cover and secure with screw.

7. Reconnect power.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

A. Green or green and yellow

ground wire

B. White wires

C. UL listed wire connectors

D. Black wires

E. UL listed or CSA approved

conduit connector

F. Downdraft vent wiring

Check Operation

1. Push and hold the button on the top of the downdraft vent

for a few seconds. The retractable section of the downdraft

vent will rise and the blower will be able to start using the

control slider. Remove any protective ﬁlm and use a stainless

steel cleaner to clean any remaining grease. Position the top

trim over the retractable section and snap trim into place.

Trim kits for matching your cooktop color are available from

your dealer.

For information on ordering, see the “Assistance or Service”

section.

2. Slide the control slider on the side of vent to check the

operation and speed of the blower.

3. If the blower does not operate:

■ Check that ﬁlter or ﬁlters are pressed in as far as they

will go.

■ Check that the circuit breaker has not tripped or

a household fuse blown.

4. Connect vent system to blower. Vent system must end with

a wall or roof cap. Use clamps or duct tape to seal all joints.

5. Install cooktop according to manufacturer’s instructions.

Check that rear of cooktop overlaps edge of retractable

downdraft vent by

" (9.5 mm). See “Countertop Cutout

Dimensions” in the “Location Requirements” section.

NOTE: To get the most-efﬁcient use from your new retractable

downdraft vent, read the “Vent System Use” section.

A. Top trim

B. On/Off button

C. Blower control slider

D. End cap

E. Filters

VENT SYSTEM USE

The retractable downdraft vent system is designed to remove

smoke, cooking vapors, and odors from the cooktop area.

■ For best results, the vent should be operating before cooking

is started.

■ If you use large or tall utensils, place them on the large rear

element or burner surface.

■ A higher heat setting than normally used may be needed

when the downdraft vent is operating.

■ For gas cooktops, the downdraft vent system may affect

the ﬂame stability and cooking performance. To improve

the burner performance, either decrease the downdraft vent

blower speed or increase the cooktop burner ﬂame setting.

■ For gas cooktops with ﬂame-sensing ignitions, the downdraft

vent system may disperse the ﬂame away from the spark

igniter and may cause it to continually spark while trying to

reignite a burner that is already lit. To resolve the issue of the

cooktop igniter continuously sparking, either decrease the

downdraft vent blower speed or increase the cooktop ﬂame

setting for that burner.

Operating Downdraft Vent

To Use:

1. Push and hold the button on top of downdraft vent for a few

seconds. (This slight delay helps avoid unintentional raising

of the vent during cleaning of the cooktop area.) Retractable

section of downdraft vent will rise. Blower will begin to vent

immediately if blower control knob slider is set to an On

position.

2. Slide the control slider on the right-hand side of the

downdraft vent to adjust the blower motor speed.

When Cooking Is Complete:

1. Push the button on top of the retractable downdraft vent.

The blower will turn off and the retractable section of the

vent will return to the closed position.

NOTE: If a spill occurs on the cooktop that allows liquids to seep

inside the downdraft vent, you must turn the downdraft vent off

immediately. It is possible to cause damage to the downdraft

vent if water is allowed inside the downdraft vent while it is

operating.

2. Immediately turn off the downdraft vent at the speed control

located on the right-hand side of the downdraft vent.

3. Turn off the power supply to the downdraft vent at the circuit

breaker box or fuse box.

4. Allow plenty of time for the downdraft vent to dry naturally.

Do not open the downdraft vent to remove the water.

VENT SYSTEM CARE

Surface of Downdraft Vent

To avoid damaging the ﬁnish, clean downdraft vent with soap

and water. Do not use scouring powder or abrasive solutions.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool

or soap-ﬁlled scouring pads.

Always wipe dry to avoid watermarks.

Cleaning Method:

■ Liquid detergent soap and water or all-purpose cleanser.

■ Wipe with damp soft cloth or nonabrasive sponge, and then

rinse with clean water and wipe dry.

NOTE: To avoid damage, do not soak cloth or sponge.

Filters

Frequently remove and clean the ﬁlter(s) in the retractable section

of the downdraft vent. This will improve the operating efﬁciency of

the downdraft vent system.

To Replace:

1. Remove each ﬁlter by pulling the spring release handle and

then pulling down the ﬁlter.

2. Wash metal ﬁlters as needed in dishwasher or hot detergent

solution.

3. Reinstall the ﬁlter by making sure the spring release handles

are toward the front. Insert metal grease ﬁlter into upper

track.

4. Pull the spring release handle down.

5. Push up on metal ﬁlter and release handle to latch into place.

6. Repeat steps 1 through 5 for the other ﬁlter.

To Clean:

1. Remove the ﬁlter(s) and clean them in a dishwasher or in a

hot detergent solution. The downdraft vent will not operate

when the ﬁlters are not in place.

2. Dry the clean ﬁlter(s) and reinstall, making sure that they lock

into place.

If Retractable Downdraft Vent Does Not Operate After

Clean Filters Have Been Installed:

Push the ﬁlter in as far as it will go. When the ﬁlter is removed,

the microswitch behind the ﬁlter is deactivated. This feature will

not allow the vent system to operate until the ﬁlter is properly

installed.

A. Spring-release handles

B. Left metal ﬁlter

C. Right metal ﬁlter

TROUBLESHOOTING

First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,

refer to the warranty page in this manual and scan the code there with your mobile device or visit https://jennair.custhelp.com.

In Canada, visit http://www.jennair.ca.

In the U.S.A.:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

PROBLEM POSSIBLE CAUSES AND/OR SOLUTIONS

Nothing will

operate

Has a household fuse been blown or has a circuit breaker tripped? Replace the fuse or reset the circuit

breaker. If the problem continues, call an electrician.

Are the ﬁlters not seating in the plenum? Make sure the ﬁlters are fully depressing the ﬁlter switches.

Has the Start button been pressed for at least 3 seconds? Push and hold the button on the top of the

downdraft vent for at least 3 seconds to complete the cycle needed to start retracting.

Vent does not

retract

Are the ﬁlters in place on downdraft vent? When the ﬁlters are removed, the microswitch behind the ﬁlter is

deactivated. This feature will not allow the vent system to operate until the ﬁlter is properly installed.

Are the ﬁlters installed correctly? Push the ﬁlter in as far as it will go to activate the microswitch behind the ﬁlter.

Has the Start button been pressed for at least 3 seconds? Push and hold the button on the top of the

downdraft vent for at least 3 seconds to complete the cycle needed to start retracting.

Is the downdraft correctly secured? Make sure that the vent hood is level and upright. Check it is securely

fastened to the ﬂoor and the counter top.

Vent partially

raises

Has an obstruction been interfering with the vent movement? Ensure the cooktop is not interfering with the

downdraft vent movement.

Is the vent level? Level the vent. See the “Install Vent System” section.

Blower does

not operate

Is the vent fully raised? Check that the vent is totally in the up position.

Are the ﬁlters installed correctly? Push the ﬁlter in as far as it will go to activate the switch behind the ﬁlter.

Has the control slider been moved from the Off position? Slide the control slider on the right-hand side of the

downdraft vent to adjust the blower motor speed.

Is the blower installed correctly? See the “Rear Mounting – Blower Motor” section.

Downdraft

not level on

countertop

Is the vent level? Level the vent. See the “Install Vent System” section.

Is the vent rising more in one side? Make sure both of the support legs have the same height from the bottom of

the vent box to the bottom of the support legs. See the “Install Vent System” section.

Vent making

noises

Was the vent recently installed and making grinding noises? Use stainless steel cleaner to remove any residue

left by the white protective ﬁlm. Ensure nothing is blocking path of vent.

Is there noise due to moving air? Ensure the installation of the product is fully into the cutout and no gap in the

middle of it.

WIRING DIAGRAM

S50

4° Speed

3° Speed

2° Speed

1° Speed

Note: Wiring Diagram is drawn

with plenum in down position

Component Layout

YL/GN

Neutral

RDRD

YL/GN

GND L N

Motor Specifications

Power supply

Frequency

Wattage rating

Amperage

Motor Resistance

120 VAC

60 Hz

420 W

3.7 A

Blue - White

Blue - Red

Blue - Gray

Blue - Black

21.6 Ohms

18 Ohms

14.3 Ohms

9.8 Ohms

Blower Switch operation

Contact

Function

1 - 3

3 - 5

5 - 7

8 - 10

10 - 12

Off

1st Speed

2nd Speed

3rd Speed

4th Speed

Num.

Filter microswitch

Plenum Down Limit Switch

Plenum Up Limit Switch

Motor microswitch

Plenum Drive motor

Blower motor

Blower Speed Switches

Start Sw. - Plenum Up/Down

Description

SEL0015061B

1 2 3

2 4

N.O.

N.C.

COM

N.O.

N.C.

COM

N.O.

N.C.

COM

N.O.

N.C.

COM

N.O.

N.C.

COM

ASSISTANCE OR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory speciﬁed parts. Factory speciﬁed parts will ﬁt

right and work right because they are made with the same

precision used to build every new appliance.

To locate factory speciﬁed replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call Jenn-Air Customer eXperience Center toll-free:

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulﬁll the product warranty

and provide after-warranty service anywhere in the

United States.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish-speaking,

hearing-impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre

toll-free at 1-800-JENNAIR (1-800-536-6247) or visit our

website at www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulﬁll the product warranty

and provide after-warranty service anywhere in Canada.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For further assistance

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

NOTE: Instructions are included with each kit.

For model series JXD7030Y

30" (76.2 cm) one-piece top trim

Order Part Number W10387676 (black)

For model series JXD7036Y

36" (91.4 cm) one-piece top trim

Order Part Number W10387677 (black)

La page est en cours de chargement...

JennAir JXD7030YS Le manuel du propriétaire

Marque: JennAir

Modèle: JXD7030YS

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: JennAir JXD7030YS Owner's manual

JennAir JXD7030YS Le manuel du propriétaire

Ce manuel convient également à

JennAir JXD7030YS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents