Miele Compact C1 Mode d'emploi

en Operating Instructions Vacuum Cleaner

fr Instructions d'utilisation Aspirateur

SCAE0

M.-Nr. 10 086 010

HS10

2

IMPORTANT SAFETY INSTRUCTIONS

Guide to the vacuum cleaner

Before using the vacuum cleaner

Using the included accessories

Use

Power cord. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Unwinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Turning the vacuum on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adjusting the suction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Opening the air inlet valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

While vacuuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Parking, transport and storage

Maintenance and care

Purchasing new filter bags and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Which filter bags and filters are the right ones? . . . . . . . . . . . . . . . . . . . . . . . . . . 14

When to change the filter bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

How to change the filter bag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

When should I change the dust compartment filter?. . . . . . . . . . . . . . . . . . . . . . . 15

Replacing the dust compartment filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

When to change the exhaust filter? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

How to replace the AirClean exhaust filter?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

How do I change the Active AirClean 50 or the HEPA AirClean 50 exhaust filter? 16

Exchanging exhaust filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

When to change the thread catcher of the floor brush AllTeQ

(depending on model) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Replacing the thread catchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Cleaning and care

Frequently asked questions

Technical service

Optional accessories

Caring for the environment

LIMITED WARRANTY - VACUUM CLEANERS USA ...................20

3

en - Contents

4

Only Miele FilterBags, filters and accessories with

the "Original Miele" logo can be used with this

vacuum. Only then can the suction power of the

vacuum cleaner reach its optimum potential creating

the best possible cleaning results.

USE OF NON-MIELE COMPONENTS MAY VOID

THE WARRANTY.

,

The use of FilterBags made of paper or a similar

material, or FilterBags with a cardboard retaining

plate can lead to serious damage to the vacuum

cleaner and may void the warranty, just as with the

use of FilterBags without the "Original Miele" logo.

The "Original Miele" Logo will appear on the

packaging or directly on the FilterBag.

Purchasing new FilterBags and filters

Original Miele FilterBags and filters can be purchased

from an authorized Miele vacuum dealer or by visiting the

Miele store at www.mieleusa.com.

When using an electrical appliance, basic precautions should always be followed,

including the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

Keep these operating instructions in a safe place and pass them on to any

future user.

WARNING-

To reduce the risk of fire, electric

shock or injury:

Before using

~

Check the voltage rating of the

vacuum cleaner before connecting the

power cord to an electrical outlet. Your

power source should correspond with

the voltage rating plate located on the

underside of the vacuum. Use only

household AC outlets. Never use DC

power sources. If you are not sure of

your home's voltage supply, consult a

qualified electrician. Connecting the

vacuum cleaner to a higher voltage

than indicated in these instructions may

result in damage to the vacuum cleaner

or injury.

~

To reduce the risk of electric shock,

this appliance has a polarized plug

(one blade is wider than the other.) This

plug will fit in a polarized outlet only one

way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does

not fit, contact a qualified electrician to

install the proper outlet. Do not alter the

plug in any way.

~

A damaged vacuum cleaner can be

dangerous. Check the packaging,

vacuum cleaner and accessories for

any signs of damage. Do not use a

damaged appliance.

~

Do not use with a damaged cord or

plug. If the appliance is not working as

it should, has been dropped, damaged,

left outdoors or submerged in water,

bring it to a service center.

~

The electrical outlet must be fitted

with a 15 A fuse.

Use

~

Do not use on people or animals.

~

Do not use outdoors or on wet

surfaces. Only dry surfaces should be

vacuumed.

~

Use only as described in this

manual. Use only Miele recommended

accessories.

~

Do not alter or modify the vacuum

cleaner.

~

This appliance is intended for

household use only.

en - IMPORTANT SAFETY INSTRUCTIONS

5

~

Do not allow the vacuum cleaner to

be used as a toy. Close attention is

necessary when used near children.

~

Never use the vacuum cleaner

without the filter bag or filters in place.

Otherwise it could be damaged.

~

If a filter bag is not inserted, the dust

compartment lid will not close. Do not

force it shut.

~

Do not leave the vacuum plugged

in. Unplug it from the outlet when not in

use and before servicing.

~

On the underside of the vacuum

handpiece is a metal insert designed to

absorb static electricity. Please make

certain that your hand remains around

this metal insert when vacuuming.

~

Persons which lack physical,

sensory or mental abilities or

experience with the machine should not

use it without supervision or instruction

by a responsible person.

~

Unwind the cord completely to aid

the vacuum cleaner in dissipating heat.

~

This vacuum should not be used to

entrap or retain any hazardous materials.

~

Do not use the vacuum cleaner to

pick up liquids or damp dirt. This could

impair the electrical safety of the

vacuum cleaner. Wait for freshly

shampooed carpets to dry.

~

Do not vacuum anything that is

burning or smoking such as cigarettes,

matches or hot ashes. The vacuum

cleaner could catch fire.

~

Do not vacuum toner dust. Toner,

such as that used in printers and

photocopiers can conduct electricity.

~

Do not use to pick up any flammable

or combustible liquids, such as

gasoline, or use in areas where they

may be present. The vacuum cleaner

could explode.

~

Do not vacuum up items which are

heavy, hard or have sharp edges. They

could cause a blockage and damage

the appliance.

~

Do not pull or carry by the cord, use

the cord as a handle, close a door on

the cord, or pull the cord around sharp

edges or corners. Do not run the

appliance over the cord. Keep the cord

away from heated surfaces.

~

Do not unplug by pulling on the cord.

To unplug, grasp the plug, not the cord.

~

Do not handle the plug or vacuum

with wet hands.

~

Keep the power cord, hair, loose

clothing, fingers and all parts of the body

away from openings and moving parts.

~

Do not place anything into the

openings of the vacuum cleaner. Do

not use if any openings are blocked;

keep them free of dust, lint, hair, or

anything that may reduce air flow.

~

This appliance is equipped with a

power cord reel. Hold plug when

rewinding onto cord reel. Do not allow

plug to whip when rewinding.

~

Turn off all controls before

unplugging.

~

Use extra care when cleaning on

stairs.

~

Floor attachments, accessories and

wands must not be used at head level

to avoid injury to eyes and ears.

en - IMPORTANT SAFETY INSTRUCTIONS

6

~

Monitor the filter bag change

indicator and inspect all filters regularly.

For best performance, the filter bag

and filters should be replaced when

necessary. A full bag or blocked filter

will reduce the vacuum cleaner's

suction power. A temperature limiter

automatically switches the vacuum

cleaner off if it gets too hot, see

"Frequently asked questions".

Using accessories

~

Unplug the vacuum when changing

accessories.

~

Do not use the vacuum without an

accessory attached. The rim could be

damaged and injuries could result from

sharp edges.

~

Miele filter bags are disposable and

intended to be used only once. Do not

attempt to reuse them. An over stuffed

filter bag will reduce the efficiency of

the vacuum cleaner.

~

Only use genuine Miele filter bags

with the Miele quality signet and

original Miele filters and accessories.

Only then will the manufacturer

guarantee its safety. Only use genuine

Miele filter bags with the Miele quality

signet and original Miele filters and

accessories. Only then will the

manufacturer guarantee its safety.

~

The hose contains electrical wires.

Do not use when damaged, cut, or

punctured. Avoid picking up sharp

objects.

~

Always turn off this appliance before

connecting or disconnecting either

hose or motorized nozzle.

Cleaning, maintenance and

repairs

~

Turn the vacuum cleaner off after

each use and before every cleaning /

maintenance. Pull the plug from the

outlet.

~

Never submerge the vacuum

cleaner in water. Clean only with a dry

cloth or slightly damp cloth when

disconnected from the mains supply. If

moisture gets into the appliance there

is a risk of electric shock.

~

Repairs must only be performed by

an authorized service agent in

accordance with national and local

safety regulations. Unauthorized repairs

could cause injury or machine damage.

~

If the power cord is damaged it

should be replaced along with a new

cable reel by Miele Technical Service.

Disposing of an old appliance

~

Before discarding an old vacuum

cleaner, please cut off the power cord

and render the plug useless. Ensure

the appliance presents no danger to

children while being stored for

disposal.

SAVE THESE

INSTRUCTIONS

en - IMPORTANT SAFETY INSTRUCTIONS

7

en - Guide to the vacuum cleaner

8

a Handpiece

b Air inlet valve

c Locking button

d Accessory clip

e Telescopic wand release button

f Dust compartment lid release

g Telescopic wand

h Filter bag

i Carrying handle

j Floor brush *

k Transport/storage holder

l Dust compartment filter (motor protection)

m Exhaust filter *

n Suction power selector

o Power cord with plug

p Cord rewind switch

q Park-System

r On / Off switch

s Airflow indicator

t Elbow

u Suction hose

The features marked * may vary or not be available depending on your model.

Some models come standard with a Turbobrush, which is not shown in this figure.

A separate Operating manual is supplied with the vacuum.

en - Guide to the vacuum cleaner

9

The illustrations referred to in the text

are shown on the fold-out pages at the

end of these operating instructions.

Before using the vacuum

cleaner

Attaching the suction hose (see fig. 1)

^

Insert the elbow into the suction

socket until it clicks. Use the inlet

guides to direct insertion.

Removing the suction hose (see fig. 2)

^ Press the release buttons at the sides

of the elbow and lift the hose from the

socket.

Connecting the suction hose and

handpiece (see fig. 3)

^ Insert the hose into the handpiece

until it clicks into place.

Connecting the handpiece and

telescopic wand (see fig. 4)

^

Insert the handpiece into the

telescopic wand until it clicks. Use

the inlet guides to direct insertion.

^

To release the handpiece from the

telescopic wand, press the locking

button (see arrow) and pull the

handpiece away from the telescopic

wand.

Adjusting the telescopic wand

(see fig. 5)

The telescoping wand is composed of

two interlocking tubes that can be

adjusted to the desired length.

^

Press the release button and slide

the tubes to the desired length.

Attaching the floor brush (see fig. 6)

^

Insert the wand into the floor brush

and twist until it locks with a click.

^

To release the floor brush from the te

-

lescopic wand, press the locking but

-

ton (see arrow).

Always follow the flooring

manufacturer's cleaning and care

instructions.

SBB -3 Smooth Floor Brush

The floor brush is suitable to vacuum

sturdy hard floors, e. g. tiles and stone

floors.

SBD 285-3 AllTeQ Floor Brush

(see fig. 7)

The floor brush is suitable for cleaning

carpets, rugs, and hard surfaces. For

flooring susceptible to scratches, use

one of the special Miele floor brushes

(see "Optional accessories").

To clean carpets and area rugs:

^

Press the foot switch marked %.

To clean hard flooring:

^

Press the foot switch marked ).

Always use the floor brush with the

bristles raised to clean floors with

very deep joints or gaps.

Turbobrush

Some models come with a Turbobrush

as an accessory. Please refer to the

separate operating instructions for

instruction on use and maintenance.

en

10

Activating the exhaust filter change

indicator

Depending on the model, one of the

following standard exhaust filters is

installed (see fig. 8).

a AirClean Filter

b Active AirClean 50 Filter (black)

c HEPA AirClean 50 Filter (white)

^

Open the dust compartment lid and

raise until it clicks into place

(see fig. 9).

^

Remove the marker strip (see fig. 10).

^ Press the exhaust filter change

indicator ~ (see fig. 11).

^ After about 10-15 seconds, a small

red marker will appear in the

left-hand side of the display

(see fig. 12).

^ Close the dust compartment lid until

it clicks into place. Take care not to

catch the dustbag in the lid.

How the exhaust filter change

indicator works

The exhaust filter change indicator

displays the usable life of the exhaust

filter. The indicator will turn fully red

after approx. 50 hours of operation,

which is equivalent to one year of

average use (see fig. 13).

Using the included accessories

(see fig. 14)

The following accessories are included:

a Dust brush

For cleaning moldings, decorative or

carved items, etc.

The head of the brush swivels and

can be turned to the best cleaning

position.

b Upholstery tool

For cleaning upholstery, mattresses,

cushions, curtains, covers etc.

c Crevice nozzle

For cleaning in folds, crevices and

corners.

d Accessory clip for the included ac-

cessories (see fig. 15)

Position the accessories as indicated

with the symbols on the accessory

holder.

^ Insert the accessory holder either on

the hand piece at the handle or on

the hose connector of the vacuum

cleaner.

Floor brush AllTeQ (see fig. 16)

(depending on model)

Also suitable for vacuuming stairs.

,

For your own safety, always

vacuum stairs from bottom to top.

en

11

Use

Power cord

,

Unwind the cord completely to

aid the vacuum in dissipating heat.

Do not pull or carry by the cord, use

the cord as a handle, close a door

on the cord, or pull the cord around

sharp edges or corners. Do not run

the appliance over the cord. Keep

the cord away from heated surfaces.

Do not unplug by pulling the cord. To

unplug grasp the plug, not the cord.

This appliance is equipped with a

power cord reel. Hold the plug when

rewinding onto cord reel. Do not

allow plug to whip when rewinding.

Unwinding (see fig. 17)

^ Hold the plug and pull the power

cord out to the required length

(maximum 18 ft / 5.5 m).

^

Insert the plug into the electrical

outlet.

,

To reduce the risk of electric

shock, the vacuum has a polarized

plug (one blade is wider than the

other). This plug will fit in a polarized

outlet only one way. If the plug does

not fit fully in the outlet, reverse the

plug. If it still does not fit, contact a

qualified electrician. Do not alter the

plug in any way.

Danger of overheating and damage.

Rewinding (see fig. 18)

^

Unplug the vacuum from the outlet.

^

Press the rewind switch briefly and

the power cord will rewind automati

-

cally.

^

Press the rewind switch again to stop

the rewinding.

^

Hold the plug so that it does not whip

around when rewinding.

Turning the vacuum on and off

(see fig. 19)

^ Press the On/Off switch.

Adjusting the suction (see fig. 20)

You can adjust the suction power to suit

the situation. When you reduce the

suction power, the floor brush can be

moved with less effort.

The symbols on the controls indicate

what each setting is suitable for.

a curtains, lightweight fabrics

b upholstery, cushions

c thick pile carpets, rugs and

runners

( energy-saving, daily vacuuming

with low noise level

e low pile carpets

f hard flooring, and intensive

cleaning of carpets

^

Turn the rotary selector to the desired

suction power setting.

en

12

Opening the air inlet valve (see fig. 21)

The air inlet valve is designed to

provide a quick, convenient reduction

of suction power, e.g. when moving

from a carpet to an area rug.

^

Open the air inlet valve far enough to

reduce the power.

Opening the air inlet valve reduces the

power to the tool being used.

While vacuuming (see fig. 22)

The vacuum cleaner can also stand on

its end for vacuuming stairs, drapes etc.

,

To prevent static electricity your

hand must touch the metal inlay on

the underside of the vacuum

handpiece. Be certain to

continuously touch this inlay when

vacuuming fine dust, flour or

sawdust as these materials are

more likely to create a static

electricity. To further prevent static

discharge while vacuuming, pull the

vacuum along by the hose with one

hand while continuing to hold the

handpiece in the other hand.

Parking, transport and storage

Park-System (see fig. 23)

The Park-System allows you to park the

telescopic wand and the suction unit on

the vacuum cleaner during brief pauses.

^

Insert the parking clip attachment on

the suction unit into the parking slot

from above.

If the vacuum cleaner is on an

incline, e.g. a ramp, slide the tube

into the telescopic wand all the way.

Park-System for storage (see fig. 24)

,

Turn the vacuum cleaner off

after use. Remove the plug from the

electrical outlet.

^

Stand the vacuum cleaner vertically.

It is helpful to completely insert the

tubes into the telescopic wand.

^

Insert the parking clip attachment on

the suction unit into the Park-System

from above.

This makes the vacuum cleaner easier

to carry and store.

Maintenance and care

,Turn off and unplug the vacuum

cleaner before performing any

maintenance work.

The Miele filter system consists of the

following three components.

–

Filter bag

–

Exhaust filter

–

Dust compartment filter

Each of these components must be

changed periodically to maintain the

vacuum cleaner’s efficiency.

Only use Miele filter bags, filters and

accessories with the "Original Miele"

logo. Only then can the suction

power of the vacuum cleaner reach

its optimum potential creating the

best possible cleaning results.

13

en

,

The use of filter bags made of

paper or a similar material, or filter

bags with a cardboard retaining

plate can lead to serious damage to

the vacuum cleaner and possibly

voiding the warranty, just as with the

use of filter bags without the

"Original Miele" logo.

Purchasing new filter bags and filters

Original Miele filter bags and filters can

be purchased from an authorized Miele

vacuum dealer or by visiting the Miele

online store.

Which filter bags and filters are the

right ones?

This vacuum cleaner uses Original

Miele filter bags Type F/J/M and an

Original Miele filters, the "Original Miele"

Logo will appear on the packaging or

directly on the filter bag.

An "AirClean" exhaust filter and a dust

compartment filter are supplied with

every box of Miele filter bags.

If you would like to purchase additional

Miele filters separately, contact your

vacuum dealer or Miele, please quote

the model number of your Miele vacuum

cleaner to ensure correct parts are

ordered. These parts are also available

to order from the online Miele store.

The exhaust filter supplied with the

vacuum cleaner can be exchanged

with another type of Original Miele filter

(see "Exchanging exhaust filters").

When to change the filter bag

(see fig. 25)

Change the filter bag when the colored

marker in the airflow indicator

completely fills the display in red.

Filter bags are disposable articles

and made to be used only once.

Dispose of full filter bags. Do not

attempt to reuse.

Clogged pores reduce the suction

power of the vacuum cleaner.

Check the airflow indicator

^ Attach the floor brush AllTeQ

(depending on model) to the vacuum

cleaner. All other suction tools can

affect the function of the airflow

indicator.

^

Use the On/ Off foot switch s to

switch the vacuum cleaner on, then

select the highest suction setting.

^

Slightly lift the floor brush AllTeQ from

the floor. If the color marker

completely fills the indicator window,

the filter bag needs to be changed.

How the airflow indicator works

The airflow indicator is designed to

show when the bag is full of common

household dust and measures the

amount of air flow through the filter bag.

Normal household dust is a mixture of

dust, hair, carpet fluff, threads, sand,

etc.

en

14

However, if fine dust, such as drill dust,

sand, plaster or flour is vacuumed, the

pores of the filter bag may become

blocked. The marker will indicate that

the bag is "full" even when it is not. The

filter bag should be changed as the

suction power is greatly reduced.

If the bag is bulging with pet fur, hair,

carpet fluff, etc. the indicator may not

register "full". This is because the air

flow of the filter bag may still be high

enough not to activate the marker to

show maximum. The filter bag should

still be changed.

How to change the filter bag

(see fig. 26 + 27)

^ Open the dust compartment lid

(see fig. 9).

The filter bag has a flap that automatically

closes to prevent dust from escaping

when the bag is removed.

^ Grasp the finger grip and pull the

filter bag out of the holder.

^

Insert the new filter bag into the hol

-

der as far as it will go. Note: Do NOT

unfold the filter bag when you first re

-

move it from the box.

^

Wait until you have inserted the filter

bag into the compartment before

unfolding it.

^

Now close the dust compartment lid

until it clicks into place, taking care

not to catch the filter bag in the lid.

,

If you do not insert a replacement

filter bag, the dust compartment lid is

designed not to close. Do not use

force!

When should I change the dust

compartment filter?

Whenever you start a new box of Miele

filter bag filters, you should change the

dust compartment filter. A new dust

compartment filter is included in every

box of Miele filter bags.

Replacing the dust compartment

filter (see fig. 28)

^

Open the dust compartment lid.

^

Open the filter frame, remove the old

filter and replace with a new one.

^

Close the filter frame.

When to change the exhaust filter?

Depending on the model, your vacuum

cleaner will use one of the following

standard exhaust filters (see fig. 8):

a AirClean Filter

Change the exhaust filter each time you

open a new box of Miele filter bags.

A new AirClean exhaust filter is included

in every box of Miele filter bags.

b Active AirClean 50 (black)

c HEPA AirClean 50 (white)

If the display of the exhaust filter

change indicator has turned fully red

(see fig. 13).

The indicator light will come on after

approx. 50 hours of operation, which is

equivalent to one year of average use.

The vacuum cleaner can still be used

however, the filter performance and

suction power will be reduced.

Instead of the Active AirClean 50 b or

HEPA AirClean 50 c exhaust filter

installed as standard, an AirClean a

exhaust filter can also be used (see

section "Maintenance and care -

Exchanging exhaust filters").

en

15

How to replace the AirClean exhaust

filter? (see fig. 29 + 30)

Make sure that only one exhaust

filter is inserted in the frame.

^

Open the dust compartment lid.

^

Open the filter frame and remove the

used AirClean exhaust filter with the

clean corner (see arrow).

^

Insert a new AirClean exhaust filter.

But if you want to install an Active

AirClean 50 filter or HEPA AirClean

50 filter, you must heed the section

"Maintenance and care - Exchanging

exhaust filters".

^ Close the filter frame.

^ Close the dust compartment lid until

it clicks into place.

How do I change the Active AirClean

50 or the HEPA AirClean 50 exhaust

filter? (see fig. 31 + 32)

Make sure that only one exhaust

filter is inserted in the frame.

^

Open the dust compartment lid.

^

Lift the Active AirClean 50 or HEPA

AirClean 50 exhaust filter and remove

it.

^

Insert the new Active AirClean 50 or

HEPA AirClean 50 exhaust filter and

press it downwards.

^

Press the exhaust filter change

indicator ~ (see fig. 11).

^

After about 10-15 seconds, a small

red marker will appear in the left-hand

side of the display (see fig. 12).

If you want to install an AirClean

exhaust filter, you must adhere to

the section "Maintenance and care -

Exchanging exhaust filters".

^

Close the dust compartment lid until

it clicks into place.

Exchanging exhaust filters

Make sure that only one exhaust

filter is inserted in the frame.

Depending on the model, your vacuum

cleaner will use one of the following

standard exhaust filters (see fig. 8):

a AirClean Filter

b Active AirClean 50 (black)

c HEPA AirClean 50 (white)

Important

1. If you replace exhaust filter a with

exhaust filter b or c, you must be sure

to remove the filter frame before

inserting the new filter type. The

exhaust filter change indicator must

also be activated (see fig. 11).

2. If you replace exhaust filter b or c

with exhaust filter a, you must be sure

to place the new filter in the filter frame

* (see fig. 31).

* Filter frame - see section on "Optional

accessories"

en

16

When to change the thread catcher

of the floor brush AllTeQ (depending

on model)

The thread catcher on the floor brush

AllTeQ can be replaced when the pile

is worn out.

Replacing the thread catchers

(see fig. 33)

^

Use a screwdriver or similar object to

remove the thread catchers from the

slots.

^

Insert the new thread catchers.

New thread catchers can be purchased

from any authorized Miele vacuum

dealer or Miele.

Cleaning the floor roller of the floor

brush AllTeQ, see fig. 34

(depending on model)

a Release the roller pin using a coin.

b Push and take out the roller axle.

c Take out the roller.

^

Remove all threads, hair etc. and

reinstall the roller and lock the roller

pin.

Cleaning and care

,

Turn off the vacuum and unplug

it from the outlet before performing

any maintenance work.

Vacuum cleaner and accessories

The vacuum cleaner and other plastic

accessories can be cleaned with a

damp cloth or a cleaner suitable for

plastics.

,

Do not use abrasive, oil-based,

glass or all purpose cleaners!

Dust compartment

The dust compartment can, if

necessary, be cleaned using a dry

cloth, dusting brush or a second

vacuum to remove any dust.

Monitor the filter bag change indicator

and inspect all filters regularly. Clean or

replace them when necessary

according to these Operating

Instructions.

,

Do not submerge the vacuum in

water. If moisture gets into the

appliance there is the risk of an

electric shock.

Frequently asked questions

The vacuum cleaner shuts off

automatically.

A temperature sensor will turn off the

vacuum cleaner if it becomes too warm.

This problem can occur if, for example,

an object is blocking the suction hose

or the filter bag pores have become

clogged with fine dust. The cause

could also be a heavily soiled exhaust

or dust compartment filter. If this

happens, turn off the vacuum cleaner

(press the On/Off foot switch s) and

unplug the power plug from the

electrical outlet.

Once the cause has been addressed,

allow the vacuum cleaner to cool for

approx. 20 - 30 minutes before

resuming vacuuming.

en

17

Technical service

In the event of a fault which you cannot

fix yourself please contact the Miele

Service Department at the phone

number listed on the back of this boo

-

klet.

^

Please quote the model type of your

appliance.

This can be found on the data plate on

the bottom of the vacuum.

Optional accessories

Always follow the flooring

manufacturer's cleaning and care

instructions.

You can order these and many other

products via the Miele website.

Some models come with the one or

more of the following accessories.

Floor tools/Brushes

Turbobrush Turbo Comfort

(STB 205-3)

For cleaning short pile textile floor

coverings.

Floor brush Hardfloor (SBB 235-3)

To vacuum sturdy hard floors, e.g. tiles.

Floor brush Parquet -3

With natural bristles for use on

hardwood-type floors that may be

susceptible to scratching, such as

parquet and laminates.

Floor brush - Parquet Twister with

swiveling head (SBB 300-3)

For cleaning all hard flooring and small

hard to reach areas.

Floor brush - Parquet Twister XL with

swiveling head (SBB 400-3)

For cleaning large areas of hard

flooring and small hard to reach areas.

Other accessories

MicroSet accessory case (SMC 20)

Accessories for use on small or

hard-to-reach items (stereos,

keyboards, models, etc).

Cat&Dog accessory case (SCD 10)

Accessories for cleaning households

with pets.

Hand Turbobrush Turbo Mini

Compact (STB 20)

For vacuuming upholstery, mattresses

or car seats.

Universal brush (SUB 20)

For dusting books, shelves etc.

Can be used with the adapter included

with the vacuum cleaner.

Dust brush with natural bristles

(SSP 10)

For dusting particularly delicate objects.

Grill / Radiator brush (SHB 30)

For cleaning radiators, narrow shelves

and crevices.

en

18

Mattress tool (SMD 10)

For use on mattresses, upholstery, and

deeper crevices.

Crevice nozzle, 300 mm (SFD 10)

Extra long crevice nozzle for cleaning in

folds, crevices and corners.

Crevice nozzle 22" (560 mm) (SFD 20)

Flexible crevice nozzle for vacuuming

hard to reach places.

Upholstery nozzle, 7 1/2" (190 mm)

(SFD 10)

Extra wide upholstery nozzle for

cleaning upholstered furniture,

mattresses and pillows.

Filters

Active AirClean 50 exhaust filter

(SF-AA 50)

Absorbs odors from the dirt in the filter

bag.

HEPA AirClean 50 exhaust filter

(SF-HA 50)

Exceptional exhaust filter for purest

exhaust air. Especially suitable for

those with allergies.

Filter frame

Required if you want to use an AirClean

exhaust filter instead of an Active Air

-

Clean 50 or HEPA AirClean 50 exhaust

filter.

Caring for the environment

Disposal of the packing material

The cardboard box and packaging

protect the vacuum cleaner during

shipping. These materials are

recyclable. Please recycle.

Ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of the reach of children.

Danger of suffocation!

Disposal of an old machine

Old vacuum cleaners may contain

materials that can be recycled. Please

contact your local recycling authority

about the possibility of recycling these

materials.

en

19

20

What This Warranty Covers And For What Period The Coverage Extends

Miele, Inc. (hereinafter "Miele") warrants to the original purchaser of this product, living in the United States of

America, who purchased their vacuum from a Miele authorized distributor or dealer:

a. That this product, including all of its Miele authorized parts is free of defects in material and workmanship.

b. That this product, if found to be defective within the stated warranty period, will be repaired free of charge to the

consumer (both parts and labor) by an authorized Miele service agent.

c. The warranty period for vacuum cleaners (excepting the S8990 and RX1 Scout), and all accessories, excluding

vacuum cleaner motors, power head motors, and vacuum cleaner casings (body), is one (1) year from the date of

purchase. For the S8990, the warranty period is five (5) years from the date of purchase.

d. For vacuum cleaner casings (body), the warranty period will be as follows:

- The structural integrity of the vacuum cleaner casing (body), will be covered for seven (7) years from the date of

purchase against defects in material and workmanship on the S2xxx, S4xxx, S5xxxx, S6xxx, S7xxx, S8xxx, S160

and S190 product series.

- The structural integrity of the vacuum cleaner casing (body) of the S8990 will be covered for ten (10) years from

the date of purchase against defects in material and workmanship.

e. For vacuum cleaner and power head motors, the warranty period will be as follows:

- Vacuum cleaner and power head motors will be covered for seven (7) years from the date of purchase on the

S2xxx, S4xxx, S5xxx, S6xxx, S7xxx, S8xxx, S160 and S190 product series.

- Vacuum cleaner and power head motors for the S8990 will be covered for ten (10) years from the date of purchase.

f. For the RX1 Scout, the warranty period is two (2) years from the date of purchase for the complete vacuum,

except for the battery, which will be warranted for one (1) year from the date of purchase.

Vacuum cleaners other than the RX1 Scout used for commercial purposes, except for their motors, will be warranted

for a period of six (6) months from the date of purchase. The motors of commercially used upright vacuums will be

warranted for one (1) year and the motors of all other commercially used vacuum cleaners, except for the RX 1 Scout

will be warranted for two (2) years. There is no warranty for the RX1 Scout used for commercial purposes. Thereafter

this Limited Warranty shall be null and void.

This warranty only applies while the product remains within the United States, and shall be null and void in any other

US territories, possessions, or foreign countries.

What is not covered by this Warranty

This warranty does not cover damage or defects caused by or resulting from repairs, service or alterations to the

product or any of its parts or accessories which have been performed by service centers or repairmen not authorized

by Miele, or damage or defects caused by negligence, accident, abuse, misuse, improper or abnormal usage or

maintenance of the product, its parts or accessories. Ordinary wear and tear or cosmetic damage (scuffs, scratches,

gouges, dents, etc.) shall not be considered a defect in materials or workmanship.

Exclusion of Other Warranties

Except for the limited warranty provided herein, Miele disclaims any and all other express warranties with respect to

the product. Any warranty of merchantability or fitness for a particular purpose is limited in its duration to the term of

the limited warranty provided herein. Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

Limitation of Liability for Special, Incidental or Consequential Damages

Miele will assume no liability, or other obligation with respect to any personal injury or property damage resulting from

the use of a vacuum cleaner, or its accessories, replacement parts, etc., which has not been purchased from, or serviced

by an Authorized Miele Dealer. Any purchaser who obtains a vacuum cleaner, accessories, replacement parts, etc., from

someone other than an Authorized Miele dealer proceeds at their own risk.

Miele specifically disclaims any and all liability, whether directly or by way of indemnity, for special incidental, consequential

or other damages, whether based on breach of contract, tort, strict or product liability, or any other legal theory.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may

not apply to you.

Special State Laws

This Limited Warranty gives you specific legal rights; you may have other rights, which vary, from state to state.

Service

For service under this Limited Warranty, or for information you may need about the product, please contact Miele at

the US address listed on the back of this booklet, or visit us at www.mieleusa.com.

Authorized Miele Dealers

To find an authorized Miele dealer in your area, please visit our website at www.mieleusa.com.

Effective Date: June 1, 2014

LIMITED WARRANTY - VACUUM CLEANERS USA

La page est en cours de chargement...

Miele Compact C1 Mode d'emploi

Miele Compact C1 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents