PRO 48 Refrigeration Use & Care Guide
2
|
Sub-Zero Customer Care 800.222.7820
PRO 48 REFRIGERATION
Customer Care
The model and serial number are printed on the enclosed
product registration card. Both numbers are also listed on
the product rating plate. Refer to page 4 for rating plate
location.
If your product ever needs attention, be sure to use a
Sub-Zero factory certied service provider recommended
by our customer care center, or select one from our list of
providers available at subzero.com/locator. All factory certi-
ed service providers are carefully selected and thoroughly
trained by us.
For warranty purposes, you will also need the date of instal-
lation and name of your authorized Sub-Zero dealer. Record
this information below for future reference.
SERVICE INFORMATION
Model Number
Serial Number
Date of Installation
Certied Service Name
Certied Service Number
Authorized Dealer
Dealer Number
Important Note
To ensure this product is installed and operated as safely
and efciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or product
damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specied.
Contents
4 PRO 48 Features
5 Electronic Controls
6 Storage
8 Operation
10 Care Recommendations
11 Technical Data
13 Troubleshooting
15 Sub-Zero Warranty
subzero.com
|
3
Thank You
Thank you for your purchase. We look forward to being part of your home for decades to
come. As a third-generation family-owned company, we take a very personal stake in the
preservation of your family’s food. We built our business and our reputation on helping
families serve the freshest food possible.
With your purchase, you receive one of the strongest warranties in the appliance industry.
Take a moment to read the full warranty statement on page 15. It’s also important to
register your Sub-Zero to ensure that you don’t miss out on exclusive owner benets,
such as; assurance that you will be taken care of in the unlikely event that service
becomes necessary during the warranty period, and a proof-of-purchase record in case
of a home insurance claim. You may register by one of the following options:
• Mail in the completed Sub-Zero product registration card.
• Register online at subzero.com/register and create a personalized My Sub-Zero/Wolf
account using the serial number on your product.
• Register by phone by calling Sub-Zero Customer Care at 800-222-7820.
As a Sub-Zero owner, you can count on ongoing support, day in and day out. Our cus-
tomer care center is available 24 hours a day, seven days a week and staffed by knowl-
edgeable product experts at our factory in Madison, Wisconsin. Should the need arise,
simply call 800-222-7820 and speak with one of our product experts. They will help
troubleshoot any issues you might have.
We are condent this guide will answer your questions about the features, operation, and
maintenance of your Sub-Zero, but if you have additional questions, please contact us at
800-222-7820 or visit us online at subzero.com.
4
|
Sub-Zero Customer Care 800.222.7820
PRO 48 Features
FEATURE
PG
1
Product Rating Plate (inside drawer)
2
2
Interior Control Panel
5
3
External Display
5
4
Glass Shelves
6
5
Slide-Out Bins
6
6
Refrigerator Crisper Drawer
7
7
Refrigerator Storage Drawer
7
8
Freezer Storage Drawer
7
9
Ice Container
7
10
Water Filtration System (behind grille)
8
11
Automatic Ice Maker
9
12
Condenser (behind grille)
10
PRO 48 FEATURES
PRO 48 glass door model.
3
5
6
10
1
11
3
12
4
7
8
9
2
subzero.com
|
5
Freezer external display.
ELECTRONIC CONTROLS
Control Panel
FUNCTION
COLDER
WARMER
Adjusts tem per ature in one-degree increments for
the refrigerator, refrigerator drawers and freezer.
Temper atures are preset at 38°F
(3°C) and 0°F
(-18°C).
ICE MAKER Turns power to ice maker on or off. Use to disable
ice maker during extended vacations.
POWER Turns unit on or off. When power is off, ‘OFF’ will
appear in the external display. Turning power off at
the control panel eliminates the need to unplug or
turn power off at the circuit breaker during service
or extended vacations.
ALARM Activates or deactivates door alarm. An audible
chime indicates door has been left ajar for more
than 30 seconds.
LIGHT Turns interior accent lighting on or off for glass
door model.
Control panel (glass door model).
Refrigerator external display.
External Display
FUNCTION
PG
Indicates freezer temperature.
5
Indicates refrigerator temperature.
5
Indicates refrigerator drawers temperature.
5
Illuminates when ice maker system is activated.
9
Illuminates when door alarm is activated.
5
REPLACE
FILTER
Illuminates when water lter needs to be
replaced.
8
SERVICE Illuminates or ashes when electronic control
system has detected a temperature or ice
maker problem, or if the condenser needs to be
cleaned.
13
6
|
Sub-Zero Customer Care 800.222.7820
Refrigerator Storage
GLASS SHELVES
To remove or adjust a glass shelf, tilt up, then lift up and out.
To reposition, insert shelf in the tracks along the back wall,
then lower the front until it locks into position. Refer to the
illustration below.
IMPORTANT NOTE: Use care when handling glass shelves to
prevent breakage or scratching the interior.
CAUTION
Glass shelves should warm to room temperature before
immersing in warm water.
SLIDE-OUT BINS
Integrated rails mounted below the glass shelves allow
slide-out bins to be positioned in a variety of locations. To
remove or adjust a slide-out bin, pull the handle of the bin
forward until it stops, lift up and out of the rails. Refer to the
illustration below.
Keeping Food At Its Best
This Sub-Zero features a unique dual refrigeration system
to keep food fresher longer. Three separate controls allow
the refrigerator, refrigerator drawers and freezer to be set at
different temperatures.
With the Sub-Zero dual refrigeration system, individual
refrigerator and freezer systems have been designed to
maintain accurate, consistent temperatures and proper
humidity levels for longer food life expectancy. Dual refrig-
eration eliminates transfer of fresh food odors to frozen
food and ice and does not freeze the moisture out of the
air in the fresh food section.
STORAGE
Glass shelf removal.
Slide-out bin removal.
subzero.com
|
7
Freezer Storage
ICE CONTAINER
To remove the ice container, pull the lower freezer drawer
forward until it stops, then lift the container up and out.
Storage Drawers
Refrigerator and freezer storage drawers are removable for
cleaning. An automatic stop is built in to prevent drawers
from coming all the way out unintentionally.
To remove, pull the drawer all the way out, lift up evenly on
both sides of the drawer front and pull out. To reinstall, raise
the front of the drawer and place onto drawer slide tracks.
Be sure to engage the front of the drawer slide with the
drawer assembly. Refer to the illustration below.
IMPORTANT NOTE: To reduce the weight of the drawer,
unload contents before removing.
STORAGE
Refrigerator Storage
CRISPER LID
To remove the crisper lid assembly, pull the upper refrig-
erator drawer all the way out, raise the front edge of the
crisper lid up and pull out from the back. Refer to the illus-
tration below.
DRAWER DIVIDERS
Dividers are interchangeable between the upper and lower
refrigerator drawers. Two long dividers run the full depth of
the drawer, with shorter dividers that connect to the long
dividers to compartmentalize the drawer.
To remove short dividers, lift up and out of supports on the
long dividers and sides of the drawer. Long dividers can be
removed by lifting up and out of drawer support tabs.
Crisper lid removal.
Storage drawer removal.
8
|
Sub-Zero Customer Care 800.222.7820
WATER FILTER REPLACEMENT
1 To access the water lter, pull out on the bottom edge
of the grille and rotate upward.
2 To remove the old lter, rotate counterclockwise one-
quarter turn, then pull out. Refer to the illustration below.
It is normal for a small amount of water to drip when
the lter is removed. It should be wiped up with a paper
towel or cloth.
3 Remove the new lter from packaging and remove the
plastic cap.
4 Insert the new lter into the manifold and turn clockwise.
5 Once the new lter has been installed, the water lter life
monitor will automatically reset.
Water Filtration System
The water ltration system of Sub-Zero PRO 48 models
supplies ltered water to the ice maker to produce great-
tasting ice.
IMPORTANT NOTE: When using the water ltration system
for the rst time and after lter replacement, it is necessary
to clear any air from the system and allow the lter to assist
in cleaning the water lines. Discard the rst two full con-
tainers of ice.
If the water ltration system will not be utilized, it can be
placed in water lter bypass mode by removing the lter.
The lter is rated for 750 gallons
(2839 L) or one year,
whichever comes rst. When the lter needs to be replaced,
‘REPLACE FILTER’ will be visible in the external display.
Replacement Sub-Zero water lters can be ordered online
at subzerowolfstore.com. For questions, contact Sub-Zero
customer care at 800-222-7820.
OPERATION
Open grille.
Water lter removal.
WATER FILTER
subzero.com
|
9
OPERATION
Ice Maker Operation
To initiate ice production, touch ICE MAKER on the control
panel.
will be visible in the external display. After initial
start-up, discard the rst few batches of ice. The ice may
contain impurities from new plumbing connections.
The ice maker will cycle (eight cubes) every two hours. If ice
is not used regularly it may fuse together. To avoid, discard
ice and allow ice maker to replenish.
To increase the ice storage capacity, remove the ice con-
tainer and allow the drawer to ll with ice.
Sabbath
This appliance is certied by Star-K to meet strict religious
regulations in conjunction with specic instructions found
on www.star-k.org.
To initiate Sabbath mode, while the unit is on, touch POWER
on the control panel. ‘OFF’ appears in the external display.
Touch and hold POWER for 10 seconds. Four audible
chimes indicate Sabbath mode has been initiated. This will
turn the unit on and disable external displays, lights, ice
maker and door alarm. To return to normal operating condi-
tions, touch POWER twice.
Interior Lighting
OVERHEAD LIGHTING
For the glass door model, the LED accent lighting can be
left on with the door closed. Accent lighting can be turned
on and off by touching LIGHT on the control panel.
DRAWER LIGHTING
Refrigerator and freezer storage drawers use standard
40-watt appliance bulbs. The bulbs are recessed into the
top of the compartment.
CAUTION
Turn power off at the control panel before replacing light
bulbs. Wear protective gloves when handling bulbs.
10
|
Sub-Zero Customer Care 800.222.7820
CARE RECOMMENDATIONS
Cleaning
INTERIOR CLEANING
To clean interior surfaces and all removable parts, wash with
a mild solution of soap, water and baking soda. Rinse and
dry thoroughly. Avoid getting water on lights and control
panel.
CAUTION
Do not use vinegar, rubbing alcohol or other alcohol-
based cleaners on any interior surface.
STAINLESS STEEL EXTERIOR
Use a nonabrasive stainless steel cleaner and apply with a
soft lint-free cloth. To bring out the natural luster, lightly wipe
surface with a water-dampened microber cloth followed by
a dry polishing chamois. Always follow the grain of stainless
steel.
CONDENSER CLEANING
CAUTION
Before cleaning the condenser, turn power off at the
control panel. Wear gloves to avoid injury from sharp
condenser ns.
The condenser is located behind the grille. To access, pull
out on the bottom edge of the grille and rotate upward. Use
a soft bristle brush and vacuum to remove dust and lint
from the condenser. Clean the condenser every three to six
months. Refer to the illustration below.
IMPORTANT NOTE: To avoid damaging condenser ns,
vacuum in the direction of the ns.
CAUTION
Failure to clean the condenser could result in tempera-
ture loss, mechanical failure or damage.
VACATIONS
For extended vacations, turn power off at the control panel.
Empty the unit and block doors open slightly to let fresh
air in and keep interior dry. Water lter should be replaced
before start up.
Condenser location.
GRILLE
SCREW
LOW-VOLTAGE
CABLES
CONDENSER
subzero.com
|
11
TECHNICAL DATA
Sub-Zero Water Filtration System Data
REPLACEMENT CARTRIDGE (4204490)
Tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor,
Particulate Class I; and against NSF/ANSI Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, Carbofuran,
1,4-dichlorobenzene, Lindane, Toxaphene, Turbidity, Cysts and Asbestos.
OPERATING SPECIFICATIONS
Capacity: certied for up to 750 gallons (2,838 L); up to twelve months
Pressure Requirement: 35 – 120 psi (2.8 – 8.2 bar)
Temperature: 33 – 100°F (0.6 – 38°C)
Flow Rate: 0.78 gpm (2.9 Lpm)
NSF
Standard
Inuent Challenge
Concentration
Average Inuent
Concentration
Product Water Concentration % Reduction
Max Permissable
Product Water
ConcentrationSubstance Average Max Efuent Average Minimum
Chlorine, Taste & Odor 42 2.0 mg/L ± 10% 1.88 mg/L 0.05 mg/L 0.06 mg/L 97.34% 96.80% ≥ 50%
Particulate 42
At least 10,000
particles/ml
5,700,000/ml 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85%
Lead at pH 6.5 53 0.15 mg/L ± 10% 0.153 mg/L <0.001 mg/L <0.001 mg/L 99.34% 99.34% 0.010 mg/L
Lead at pH 8.5 53 0.15 mg/L ± 10% 0.150 mg/L <0.001 mg/L <0.001 mg/L 99.33% 99.33% 0.010 mg/L
Mercury at pH 6.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0003 mg/L 0.0005 mg/L 95.00% 91.66% 0.002 mg/L
Mercury at pH 8.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0008 mg/L 0.0015 mg/L 86.66% 75.00% 0.002 mg/L
Atrazine 53 0.009 mg/L ± 10% 0.009 mg/L <0.002 mg/L <0.002 mg/L 77.77% 77.77% 0.003 mg/L
Benzene 53 0.015 mg/L ± 10% 0.014 mg/L 0.0006 mg/L 0.0011 mg/L 95.71% 92.14% 0.005 mg/L
Carbofuran 53 0.08 mg/L ± 10% 0.081 mg/L <0.001 mg/L <0.001 mg/L 98.76% 98.76% 0.04 mg/L
1,4-dichlorobenzene 53 0.225 mg/L ± 10% 0.208 mg/L <0.0005 mg/L <0.0005 mg/L 99.75% 99.75% 0.075 mg/L
Lindane 53 0.002 mg/L ± 10% 0.002 mg/L 0.00003 mg/L 0.00007 mg/L 98.50% 96.50% 0.0002 mg/L
Toxaphene 53 0.015 mg/L ± 10% 0.015 mg/L <0.001 mg/L <0.001 mg/L 93.33% 93.33% 0.003 mg/L
Turbidity 53 11 ± 1 NTU 10.7 NTU 0.31 NTU 0.49 NTU 97.10% 95.42% 0.5 NTU
Cysts** 53 Minimum 50,000/L 166,500/L <1/L <1/L >99.99% >99.99% >99.95%
Asbestos 53 10
7
to 10
8
bers/L
†
155 MF/L <1 MF/L <1 MF/L >99.99% >99.99% >99%
**Based on the use of Cryptosporidium Parvum oocysts † Fibers greater than 10 μm in length
• Do not use with water that is microbiologically unsafe or of unknown
water quality without adequate disinfection before or after the
system.
• Systems certied for cyst reduction may be used on disinfected
waters that may contain lterable cysts.
• This system must be installed, operated, maintained and lters
replaced as required in order for the product to perform as adver-
tised.
• Note that while the testing was performed under standard labora-
tory conditions, actual performance may vary. The contaminants
or other substances removed or reduced by this water treatment
system are not necessarily in your water.
SPECIAL NOTES
• Replacement Sub-Zero water lter cartridges can be ordered online
at subzerowolfstore.com. For questions, contact Sub-Zero customer
care at 800-222-7820.
• Change lter cartridge at least every twelve months. High sediment
areas may require more frequent lter cartridge replacement.
• Installation and operation instructions, parts and service availability,
and standard warranty are included with the product when
shipped.
• Replace water lter cartridge when the lter indicator is lit or when
water ow becomes too low. Use replacement water lter cartridge
part number 4204490. Replacement lter pricing information can be
found at subzero.com.
Manufactured for: Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744, 800-222-7820
This system has been tested according to NSF/ANSI 42/53 for reduc-
tion of the substances listed below. The concentration of the indicated
substances in water entering the system was reduced to a concentra-
tion less than or equal to the permissible limit for water leaving the
system, as specied in NSF/ANSI 42/53.
12
|
Sub-Zero Customer Care 800.222.7820
TECHNICAL DATA
subzero.com
|
13
TROUBLESHOOTING
Troubleshooting
UNIT OPERATION
No lights or cooling.
• Verify power is on.
• Verify electrical power to unit and home circuit breaker
is on.
No lights in refrigerator or freezer.
• Door may have been left ajar which has disabled lights
to eliminate excess heat. If lights are out, close door for
one hour. If lights are still out, contact Sub-Zero factory
certied service.
• LED interior lighting must be replaced by Sub-Zero
factory certied service.
Frost, condensation or ice build up inside unit.
• Verify condenser is clean.
• Verify door/drawer is closing properly.
• Verify door/drawer has not been left ajar.
• Verify door/drawer gasket does not have rips or tears. If
it does, contact Sub-Zero factory certied service.
• If icing is heavy, turn unit off and use a hair dryer to melt
ice. Hair dryer should be set on low and kept moving
at all times. Once ice has melted, wipe up water with a
cloth or paper towel.
High temperatures, unit runs excessively or unit giving off
too much heat.
• Verify condenser is clean.
• Verify door/drawer is closing properly.
• Verify door/drawer has not been left ajar.
• Increased ambient temperatures may cause compres-
sors to run longer.
• If temperature display shows 38° and 0°, but is not
cooling, unit may be in showroom mode. Contact
Sub-Zero Customer Care at 800-222-7820.
ICE PRODUCTION
No ice.
• Verify
appears in freezer external display.
• Verify ice maker has been on for at least 24 hours.
• Verify freezer temperature near 0°F.
• Verify ice container is properly installed.
• Verify ice maker arm in down position.
• Verify water is being supplied to unit.
• Verify water lter has been replaced within the last 12
months and installed properly.
• Verify water lter has been removed if a reverse osmosis
ltration system is being utilized.
• Verify
is not ashing. If ashing, contact Sub-Zero
factory certied service.
Blue or green ice.
• Possible copper supply line corrosion. Contact plumber
to clean or replace.
Black ecks in cubes.
• Stop use and contact Sub-Zero factory certied service.
Bad taste.
• Defrost freezer and clean with soap and water.
• Place coffee grounds or charcoal briquettes in freezer to
absorb odor.
Hollow cubes.
• Clean condenser. Contact Sub-Zero factory certied
service if unresolved.
14
|
Sub-Zero Customer Care 800.222.7820
TROUBLESHOOTING
Sub-Zero, Sub-Zero & Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trade-
marks and service marks of Sub-Zero, Inc. Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf
Appliance, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
Troubleshooting
ODOR
• Unit should be cleaned before using for the rst time.
This will clear any odors that may have been trapped
during shipping.
• Clean unit and shelving thoroughly.
• Uncovered food could create odor which may require
cleaning.
• Remove and clean drain pan located behind kickplate,
and reinstall.
SERVICE
• Maintain the quality built into your product by contacting
Sub-Zero factory certied service. For the name of the
nearest Sub-Zero factory certied service, check the
contact & support section of our website, subzero.com
or call Sub-Zero customer care at 800-222-7820.
• When contacting service, you will need the model and
serial number of your unit. Both numbers are listed on
the product rating plate. Refer to page 4 for rating plate
location.
• For warranty purposes, you will also need the date
of installation and name of your authorized Sub-Zero
dealer. This information should be recorded on page 2.
Sub-Zero Residential Limited Warranty
FOR RESIDENTIAL USE
FULL TWO YEAR WARRANTY*
For two years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, any part of the product that proves to be defec-
tive in materials or workmanship. All service provided by Sub-Zero under the above warranty must be
performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will
be provided during normal business hours.
FULL FIVE YEAR SEALED SYSTEM WARRANTY
For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and
labor to repair or replace, under normal residential use, these parts that prove to be defective in materials
or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided
by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless
otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.
LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY
For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts
that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and
all connecting tubing. If the owner uses Wolf factory certied service, the service provider will repair or
replace these parts with the owner paying for all other costs, including labor. If the owner uses non-
certied service, the owner must contact Wolf Appliance (using the information below) to receive repaired
or replacement parts. Wolf Appliance will not reimburse the owner for parts purchased from non-certied
service or other sources.
TERMS APPLICABLE TO EACH WARRANTY
The warranty applies only to products installed for normal residential use. The warranty applies only to
products installed in any one of the fty states of the United States, the District of Columbia or the ten
provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by
negligence, accident or improper use, maintenance, installation, service or repair.
THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.
WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF
LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,
IMPLIED OR STATUTORY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also
have other legal rights that vary from state to state.
To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact
Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,
subzero.com, email us at [email protected] or call 800-222-7820.
*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited
60-day parts and labor warranty for cosmetic defects.
*Replacement water lters and air purication cartridges are not covered by the product warranty.
2
|
Atención al cliente de Sub-Zero 800.222.7820
UNIDAD DE REFRIGERACIÓN PRO 48
Atención al cliente
El modelo y número de serie están impresos en la tarjeta
de registro del producto adjunta. Los dos números también
aparecen en la placa de datos del producto. Consulte la
página 4 para encontrar la placa de datos.
Si su producto alguna vez necesita servicio, asegúrese de
usar un proveedor de servicios certicado por Sub-Zero y
recomendado por nuestro centro de atención al cliente, o
seleccione uno de nuestra lista de proveedores disponibles
en subzero.com/locator. Todos los proveedores de servicio
certicados de fábrica han sido cuidadosamente seleccio-
nados y entrenados a fondo por nosotros.
Para nes de la garantía, usted también necesitará la fecha de
instalación y el nombre de su distribuidor autorizado de Sub-
Zero. Anote esta información abajo para referencia futura.
INFORMACIÓN PARA SERVICIO
Número de modelo
Número de serie
Fecha de instalación
Nombre de servicio certicado
Número de servicio certicado
Distribuidor autorizado
Número de distribuidor
Aviso importante
Para garantizar que este producto sea instalado y operado
de la forma más segura y eciente posible, tome nota de los
siguientes tipos de información resaltada en esta guía:
AVISO IMPORTANTE resalta la información que es especial-
mente importante.
PRECAUCIÓN indica una situación en la que se pueden sufrir
heridas leves o provocar daños al producto si no se siguen
las instrucciones.
ADVERTENCIA indica peligro de que se produzcan heridas
graves o incluso la muerte si no se siguen las precauciones.
AVISO IMPORTANTE: En toda esta guía, las dimensiones
entre paréntesis son milímetros, a menos que se especique
lo contrario.
Contenido
4 Características de PRO 48
5 Controles electrónicos
6 Almacenamiento
8 Operación
10 Recomendaciones de cuidado
11 Datos técnicos
13 Resolución de problemas
15 Garantía de Sub-Zero
subzero.com
|
3
Gracias
Muchas gracias por su compra. Esperamos poder ser parte de su hogar durante las
décadas venideras. Como una empresa familiar de tercera generación, tenemos un interés
muy personal en conservar los alimentos de su familia. Hemos construido nuestro negocio y
nuestra reputación al ayudar a las familias a servir la comida más fresca posible.
Con su compra, usted recibe una de las garantías más sólidas en la industria de los elec-
trodomésticos. Lea la declaración de garantía completa de la página 15. También es impor-
tante que registre su Sub-Zero para asegurarse de no perder los benecios de propie tario
exclusivo, como por ejemplo, la garantía de que va a recibir atención en el improbable caso
de que necesite servicio durante el periodo de garantía, y un registro de prueba de compra
en caso de una reclamación sobre el seguro de vivienda. Puede registrarse mediante una de
las siguientes opciones:
• Envíe la tarjeta de registro del producto completada a Sub-Zero.
• Regístrese en línea en subzero.com/register y cree una cuenta personal en My
Sub-Zero/Wolf con el número de serie de su producto.
• Regístrese por teléfono llamando a la línea de atención al cliente de Sub-Zero
al 800-222-7820.
Como propietario de un Sub-Zero, puede contar con soporte técnico constante, día tras
día. Nuestro centro de atención al cliente está disponible 24 horas al día, los siete días a la
semana, y compuesto por expertos conocedores del producto en nuestra fábrica en Mad-
ison, Wisconsin. En caso necesario, simplemente llame al 800-222-7820 y hable con uno de
los expertos de nuestros productos. Ellos le ayudarán a solucionar cualquier pro-blema que
pueda tener.
Estamos seguros de que esta guía contestará sus preguntas acerca de las características,
funcionamiento y mantenimiento de su Sub-Zero, pero si usted tiene preguntas adicionales,
por favor póngase en contacto con nosotros en el 800-222-7820 o visítenos en línea en
subzero.com.
4
|
Atención al cliente de Sub-Zero 800.222.7820
Características de PRO 48
CARACTERÍSTICA
PÁG.
1
Placa de datos del producto (al interior del cajón)
2
2
Panel de control interior
5
3
Pantalla exterior
5
4
Estantes de cristal
6
5
Cajones corredizos
6
6
Cajón para frutas y verduras del refrigerador
7
7
Cajón de almacenamiento del refrigerador
7
8
Cajón de almacenamiento del congelador
7
9
Contenedor de hielo
7
10
Sistema de ltrado de agua (detrás de la rejilla)
8
11
Fabricador automático de hielo
9
12
Condensador (detrás de la rejilla)
10
CARACTERÍSTICAS DE PRO 48
Modelo PRO 48 con puerta de cristal.
3
5
6
10
1
11
3
12
4
7
8
9
2
subzero.com
|
5
Pantalla exterior
del congelador.
CONTROLES ELECTRÓNICOS
Panel de control
FUNCIÓN
COLDER
(MÁS FRÍO)
WARMER
(MENOS FRÍO)
Ajuste en intervalos de un grado la temperatura
del refrigerador, los cajones del refrigerador y el
congelador. Las temperaturas están preestab-
lecidas en 38°F
(3°C) y 0°F (-18°C).
ICE MAKER
(FABRICADOR
DE HIELO)
Enciende o apaga el fabricador de hielo.
Utilícelo para desactivar el fabricador de
hielo durante temporadas de vacaciones
prolongadas.
POWER
(ENERGÍA)
Enciende o apaga la unidad. Cuando está
apagada, aparecerá ‘OFF’ en la pantalla exte-
rior. Desactivar la alimentación en el panel de
control elimina la necesidad de desconectar la
unidad o de apagar el suministro eléctrico en el
disyuntor durante el servicio o las vacaciones
prolongadas.
ALARM
(ALARMA)
Activa o desactiva la alarma de la puerta. Un
aviso sonoro indica que la puerta se quedó
abierta por más de 30 segundos.
LIGHT (LUZ) Enciende o apaga la luz de acento interior para
los modelos con puerta de cristal.
Panel de control (modelo con puerta de cristal).
Pantalla exterior
del refrigerador.
Pantalla exterior
FUNCIÓN
PÁG.
Indica la temperatura del congelador.
5
Indica la temperatura del refrigerador.
5
Indica la temperatura de los cajones
del refrigerador.
5
Se ilumina al activarse el sistema de
fabricación de hielo.
9
Se ilumina al activarse la alarma de
la puerta.
5
REPLACE
(REEMPLAZAR)
FILTER
(FILTRO)
Se ilumina cuando es necesario cam-
biar el ltro de agua.
8
SERVICIO Se ilumina o parpadea cuando el
sistema de control electrónico detecta
un problema con la temperatura o el
fabricador de hielo, o cuando es nece-
sario limpiar el condensador.
13
6
|
Atención al cliente de Sub-Zero 800.222.7820
Almacenamiento del refrigerador
ESTANTES DE CRISTAL
Para extraer o ajustar un estante de cristal, inclínelo hacia
arriba, luego levántelo hacia arriba y hacia afuera. Para
volver a colocarlo, inserte el estante en las guías que corren
a lo largo de la pared posterior, luego baje la parte delantera
hasta que encaje en su posición. Consulte la siguiente
ilustración.
AVISO IMPORTANTE: Tenga cuidado al manipular los
estantes de cristal para evitar que se rompan o que rayen el
interior.
PRECAUCIÓN
Debe dejar que los estantes de cristal alcancen la tem-
peratura ambiente antes de sumergirlos en agua tibia.
CAJONES CORREDIZOS
Los rieles incorporados que están instalados debajo de los
estantes de cristal permiten que los cajones corredizos se
puedan ubicar en diversos lugares. Para extraer o ajustar un
cajón corredizo, jale la manija del cajón hacia el frente hasta
que llegue al tope, levántelo y sáquelo de los rieles. Con-
sulte la siguiente ilustración.
Conservación de los alimentos frescos
Esta unidad Sub-Zero incorpora un exclusivo sistema de
refrigeración doble para mantener los alimentos frescos
durante más tiempo. Tres controles independientes per-
miten ajustar temperaturas diferentes en el refrigerador, los
cajones del refrigerador y el congelador.
Con el sistema de refrigeración doble de Sub-Zero, los
sistemas individuales del refrigerador y el congelador han
sido diseñados para mantener una temperatura precisa y
constante, así como niveles de humedad adecuados para
que los alimentos se conserven durante más tiempo. La
refrigeración doble elimina la transferencia de olores de los
alimentos frescos a los congelados o al hielo y no congela
la humedad presente en el aire en la sección de alimentos
frescos.
ALMACENAMIENTO
Extracción de los estantes
de cristal.
Extracción de los cajones
corredizos.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
dans d''autres langues
- English: Sub-Zero 648PROG User guide
- español: Sub-Zero 648PROG Guía del usuario
- português: Sub-Zero 648PROG Guia de usuario