AT&T TL86009 Manuel utilisateur

User’s manual

TL86009

DECT 6.0 expansion handset

for use with AT&T model

TL86109

corded/cordless telephone/

answering system with

BLUETOOTH® wireless technology

Congratulations

on your purchase of this AT&T product. Before using this AT&T

product, please read Important safety information on

pages 24-26 of this manual. For complete instructions, please

refer to the manual provided with your TL86109 telephone. For

customer service or product information, please visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

This telephone meets the California Energy Commission regulations

for energy consumption. Your telephone is set up to comply with the

energy-conserving standards right out of the box. No further action

is necessary.

Model number: TL86009

Type: DECT 6.0 expansion handset

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be

found on the bottom of the telephone base.

Save your sales receipt and original packaging in case it is

necessary to return your telephone for warranty service.

the AT&T logo are trademarks of AT&T Intellectual Property licensed to

Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Telephones identied with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use

of such marks by Advanced American Telephones and its parent, VTech Holdings

Limited, is under license. VTech Holdings Limited is a member of Bluetooth SIG, Inc.

Other trademarks and trade names are those of their respective owners.

Parts checklist

Your telephone package contains the following items. Save your

sales receipt and original packaging in the event warranty service

is necessary.

Battery for

cordless handset

Cordless handset

Charger for cordless

handset with power

adapter installed

Battery

compartment

cover

User’s manual

Belt clip for

cordless handset

BY 1021

BT183342/BT283342

2.4V 400mAh Ni-MH

User’s manual

TL86009

DECT 6.0 expansion handset

for use with AT&T model

TL86109

corded/cordless telephone/

answering system with

BLUETOOTH® wireless technology

Table of contents

Getting started

Installation .............................................. 1

Quick reference guide ...................2

Charger installation ..........................5

Battery installation and

charging ...............................................6

Battery charging .................................8

Belt clip & optional headset ........9

Adding handset to your

telephone base

Adding and registering

handsets ........................................... 10

Expand your telephone

system ................................................. 11

Add and register a handset ....11

Replace a handset ...........................12

Appendix

Troubleshooting................................13

Maintenance ....................................... 23

Important safety information .24

Safety information .....................24

Especially about cordless

telephones ....................................... 25

Precautions for users of

implanted cardiac

pacemakers ....................................26

Pacemaker patients ..................26

Especially about telephone

answering systems ....................26

For C-UL compliance ..................... 27

Mesures de sécurité

importantes .................................... 27

FCC Part 68 and ACTA ..................30

FCC Part 15 ........................................... 32

California Energy Commission

battery charging testing

instructions ..................................... 33

Limited warranty .............................34

Technical specications ...............37

1

See pages 6-8

for easy instructions.

You must install and

charge the battery before

using the telephone.

STOP!

Installation

Your product may be shipped with a protective sticker covering the

handset display - remove it before use.

For customer service or product information, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

Avoid placing the telephone base too close to:

Communication devices such as television sets, VCRs, or other

cordless telephones.

Excessive heat sources.

Noise sources such as a window with trac outside, motors,

microwave ovens, refrigerators, or uorescent lighting.

Excessive dust sources such as a workshop or garage.

Excessive moisture.

Extremely low temperature.

Mechanical vibration or shock such as on top of a washing

machine or workbench.

•

Getting started

Quick reference guide

Getting started

CHARGE light

(blue ring around

DIR/ /VOL/ /CID)

On when the handset is

charging in the charger.

DIR/ /VOL

Press to scroll up while in

menus.

Press to increase the

volume level during a call.

Press to show directory

entries when the telephone

is not in use.

While entering names or

numbers, press to move

the cursor to the right.

VOL/ /CID

Press to scroll down while

in menus.

Press to decrease the

volume level during a call.

Press to show the caller ID

history when the telephone

is not in use.

While entering names or

numbers, press to move

the cursor to the le.

CELL

Press to make or answer a

cell call.

Flashes quickly when there

is an incoming cell call.

Flashes slowly when a cell call

is on hold.

OFF/CLEAR

While using menus, press

to cancel an operation,

back up to the previous

menu, or exit the menu

display. Press and hold to

return to idle mode.

While entering names or

numbers, press to delete a

digit or a character.

During a call, press to

hang up.

Sokeys (2)

Press to select a menu item

displayed above the key.

2

Quick reference guide

Getting started

3

1 LINE/FLASH/

2 LINE/FLASH

Press 1 LINE/FLASH

to make or answer a

call on line 1. During a

call, press to answer an

incoming call on line 1

when you receive a call

waiting alert.

Press 2 LINE/FLASH

to make or answer a

call on line 2. During a

call, press to answer an

incoming call on line 2

when you receive a call

waiting alert.

TONE

Press to switch to tone

dialing temporarily

during a call if you have

pulse service.

1

While reviewing a caller

ID history entry, press

repeatedly to add or

remove 1 in front of

the telephone number

before dialing or saving

it in the directory.

REDIAL/PAUSE

Press to view the

redial list.

While entering numbers,

press and hold to insert a

dialing pause.

/SPEAKER

Press to turn on the

handset speakerphone.

Press again to resume

normal handset use.

HOLD

Press to put a call

on hold.

# (pound key)

Press repeatedly to

display other dialing

options when reviewing a

caller ID history entry.

Quick reference guide

Getting started

4

PLAY MESSAGES

BACK SELECT

Press the MENU softkey to

enter the main menu which

includes the following:

PLAY MESSAGES

ANSWERING SYS

DIRECTORY

CALL LOG

INTERCOM

RINGER

SETTINGS

WEBSITE

EQ

During an outside call, intercom

call, message or announcement

playback, press to change the

quality of the audio to best suit

your hearing.

HANDSET

L1)

L2)

CL)

MENU

IMPORTANT INFORMATION

1. Use only the power adapter supplied with this product. To order a replacement

power adapter, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

2. The power adapter is intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

5

Charger installation

Install the charger, as shown below.

Getting started

Plug the power adapter into an electrical outlet

not controlled by a wall switch.

Battery installation and charging

Getting started

6

Install the battery, as shown below.

T

H

I

S

SI

DE

U

P

/

C

E

C

Ô

T

É

V

ER

S

L

E HA

U

T

B

a

t

e

ry

P

a

c

k

/

B

l

o

c-

p

i

l

e

s

:

B

T

18

3

4

2

/

B

T

2

8

3

34

2

(

2

.

4

V

4

00mA

h

N

i

-MH)

WA

R

N

I

N

G

/

A

V

E

R

T

I

S

E

M

E

N

T

:

D

O

N

O

T

B

U

R

N

O

R

P

U

N

C

T

U

R

E

B

A

T

E

R

I

E

S

.

N

E

P

A

S

I

N

C

I

N

É

R

E

R

O

U

P

E

R

C

E

R

L

E

S

P

I

L

E

S

.

M

ad

e

i

n

C

h

i

n

a

/

F

a

b

ri

q

u

é

en

ch

i

n

e

GP

08

4

1

TH

IS

S

I

DE UP

/

CE

C

Batt

e

ry

P

ack

/

Bl

o

c

-

p

i

l

e

BT

18

33

42/B

T

2

83

3

4

2

(

W

ARN

I

NG

/

A

VERT

DO

NO

T

B

U

RN

O

NE

P

AS

I

NC

I

N

Ma

d

e

i

n

Ch

Step 1

Plug the battery connector securely into the socket inside the

handset battery compartment, matching the color-coded label.

Insert the supplied battery with the label THIS SIDE UP facing up,

as indicated.

Step 2

Align the cover at against the battery compartment, then slide it

upwards until it clicks into place.

Step 3

Charge the handset by placing it face

up in the charger. The CHARGE light is

on when charging.

CHARGE light

IMPORTANT INFORMATION

1. Use only the supplied rechargeable battery or replacement battery (model

BT183342/BT283342). To order, visit our website at

www.telephones.att.com or call 1 (800) 222-3111. In

Canada, dial 1 (866) 288-4268.

2. If you do not use the handset for a long time, disconnect and remove the

battery to prevent possible leakage.

Battery installation and charging

Getting started

7

SET DATE

--/--/--

MM/DD/YY

SET

SET TIME

--:-- --

SET

Aer you install your telephone or power

returns following a power outage, the handset

will prompt you to set the date and time. To skip

setting the date and time, press OFF/CLEAR.

To replace the battery, press the tab and slide

the battery compartment cover downwards. Li

out the old battery and disconnect it from the

handset. Follow the instructions on page 6 to

install and charge the new battery.

8

Battery charging

Once you have installed the battery, the screen indicates the

battery status (see the following table). If necessary, place the

handset in the telephone base or charger to charge the battery.

For best performance, keep the handset in the telephone base

or charger when not in use. The battery is fully charged aer 16

hours of continuous charging. See the table on page 37 for battery

operating times.

If the screen shows Low battery, you need to charge the handset

without interruption for at least 25 minutes to give the handset

enough charge to use the telephone for a short time. The following

table summarizes the battery charge indicators and actions to

take.

Getting started

Battery indicators Battery status Action

The screen is blank, or

shows Place in charger.

The battery has very

little or no charge. The

handset cannot be

used.

Charge without interruption

until the screen shows

Low battery or HANDSET

X (at least ve minutes).

The screen shows

Low battery and

ashes.

Battery has enough

charge to be used for a

short time.

Charge without interruption

until the screen shows

HANDSET X (at least 25

minutes).

The screen shows

HANDSET X.

Battery is charged. To keep the battery

charged, place it in the

telephone base or charger

when not in use.

NOTE: If you are on a phone call in low battery mode, you hear four short beeps

every minute.

Getting started

Belt clip & optional headset

For handsfree telephone conversations, you can use any industry

standard 2.5 mm headset (purchased separately). For best

results, use an AT&T 2.5 mm headset. To purchase a headset,

visit our website www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

Plug a 2.5 mm headset

into the jack on the side

of handset (beneath the

small plastic cover).

Li the plastic

cover here.

Side of handset

To attach the belt clip:

Snap the belt clip into

the slots on both sides of

the handset, as shown in

the gure.

To remove the belt clip:

Gently li either of the

belt clip tabs, shown in

the gure, outwards

to remove the belt clip

from the handset.

9

Adding and registering handsets

Before using a new TL86009 handset, you must register it with

the AT&T TL86109 telephone system (purchased separately).

The AT&T TL86109 telephone system can accommodate up to

12 handsets.

The handset provided with the TL86109 comes registered as

HANDSET. You can register up to 11 additional handsets to the

telephone base, and they will be assigned numbers in the order

they are registered (HANDSET 2, HANDSET 3, HANDSET 4 and

so on). Your rst handset is then renamed as HANDSET 1.

Adding handset to your telephone base

10

Expand your telephone system

Add and register a handset

When rst purchased, each expansion handset shows

Press [HOLD] on base for 4 sec, then press [#] on handset

aer a battery is installed. Each handset should be charged

without interruption for at least 25 minutes before registering

to the telephone base. For more details on battery charging,

see the table on page 8.

To register a handset:

Press and hold HOLD on the

telephone base for about

four seconds until it shows

Registering...Please wait.

Then, release the button.

Press # (pound key) on the

handset. Its screen shows

Registering handset... and

it takes up to 60 seconds to

complete the registration. The

handset and telephone base show HANDSET X Registered (X

represents the handset number assigned) and you hear a beep

when the registration completes.

NOTES:

If the registration fails, the handset shows Registration failed for a few

seconds and then

Press [

HOLD]

on base for 4 sec, then press [#] on

handset.

Try the registration process again.

You cannot register a handset if any other system handset is in use.

You cannot register more than 12 handsets to the telephone base.

Registration slots are full shows on the base screen while you are in

step 2.

1.

2.

•

Adding handset to your telephone base

11

Adding handset to your telephone base

12

Replace a handset

If you want to replace a handset or reassign the designated

handset number of a registered handset, you must deregister all

the handsets and then individually register each handset.

To make deregistration easier, read all of the instructions on this

page before you begin.

To deregister all handsets:

Press and hold FLASH on the telephone base for about

4 seconds until it shows Deregister all handsets?. Then,

release the button.

Press the YES sokey to continue. You hear a conrmation tone

from the telephone base.

The telephone base displays PLEASE WAIT.... All system

handsets show Out of range OR no power at base for a few

seconds, and then you hear a conrmation tone from the

handset.

All the handsets show Press [HOLD] on base for 4 sec, then

press [#] on handset when the deregistration completes. The

deregistration process takes about 10 seconds to complete.

If deregistration fails, you may need to reset the telephone and try

again.

To reset:

Unplug the power from the telephone base, then plug it back in.

Aer deregistering, register each handset individually. See Add

and register a handset on page 11.

NOTES:

You cannot deregister the handset(s) if any other system handset is in use.

During deregistration, all cordless handset(s) and DECT 6.0 cordless

headset(s) will also be deregistered.

1.

2.

3.

4.

•

Troubleshooting

If you have diculty with your phone, please try the following

suggestions. For Customer Service, visit our website at

www.telephones.att.com or call 1 (800) 222-3111.

In Canada, dial 1 (866) 288-4268.

My phone doesn’t work at all.

Make sure the power cord is securely plugged in.

Make sure you plug the battery connector securely into the

cordless handset.

Make sure you plug the telephone line cord securely and rmly

into the telephone base and the telephone wall jack.

Charge the battery in the cordless handset for at least 16 hours.

For optimum daily performance, return the cordless handset to

the telephone base or charger when not in use.

If the battery is depleted, it might take approximately ve

minutes to charge the handset before it shows Low battery. See

page 8 for details.

Reset the telephone base. Unplug the electrical power. Wait for

approximately 15 seconds, then plug it back in. Allow up to one

minute for the cordless handset and telephone base to reset.

You may need to purchase a new battery. Refer to Battery

installation and charging (pages 6-7) in this user’s manual.

•

Appendix

13

Troubleshooting

Appendix

14

The display shows NO LINE. I cannot get a dial tone.

Try all the suggestions mentioned above.

If the previous suggestions do not work, disconnect the

telephone line cord from your telephone and connect the

telephone line cord to another telephone.

If there is no dial tone on that other telephone either, your

telephone line cord may be defective. Install a new telephone

line cord.

If changing the telephone line cord does not help, the wall

jack (or the wiring to this wall jack) may be defective. Try

using a dierent wall jack in your home to connect your

TL86109 telephone, or contact your telephone service

provider (charges may apply).

I cannot dial out.

Try all the suggestions mentioned above.

Make sure you have a dial tone before dialing. The cordless

handset might take a second or two to nd the telephone base

and produce a dial tone. This is normal. Wait an extra second

before dialing.

Eliminate any background noise. Noise from a television, radio or

other appliances might cause the phone to not dial out properly.

If you cannot eliminate the background noise, try muting the

cordless handset before dialing, or dialing from another room

with less background noise.

If other phones in your home are having the same problem,

contact your telephone service provider (charges might apply).

•

Troubleshooting

Appendix

My cordless handset isn’t performing normally.

Make sure you plug the power cord securely into the telephone

base. Plug the power adapter into a dierent, working electrical

outlet without a wall switch.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

The handset registration is unsuccessful.

Follow the steps to register the handset again.

1. Make sure the handset is out of the charger and shows

Press

[

HOLD]

on base for 4 sec, then press [#] on handset

before

you begin.

2. Press and hold HOLD on the telephone base for about four

seconds until it shows Registering...Please wait. Then, release

the button.

3. Press # (pound key) on the handset. Its screen shows

Registering handset... and it takes up to 60 seconds to

complete the registration. The handset shows HANDSET X

Registered (X represents the handset number assigned) and

you hear a beep when the registration completes.

Refer to Add and register a handset on page 11 for details.

•

15

Out of range OR no power at base appears on my cordless

handset.

Make sure that the telephone base is powered up.

Move the cordless handset closer to the telephone base. You

might have moved out of range.

Reset the telephone base. Unplug the electrical power. Wait for

15 seconds, then plug it back in. Allow up to one minute for the

cordless handset and telephone base to reset.

Other electronic products such as HAM radios and other DECT

phones, can cause interference with your cordless phone. Try

installing your phone as far away as possible from these types of

electronic devices.

The batteries do not hold a charge.

If the cordless handset is in the charger and the charge light

does not come on, refer to The charge light is o (page 21) in

this Troubleshooting guide.

Charge the battery in the cordless handset for at least 16 hours.

For optimum daily performance, return the cordless handset to

the charger when not in use.

If the battery is depleted, it may take approximately ve

minutes to charge the handset before it shows Low battery.

See page 8 for details.

You may need to purchase a new battery. Please refer to

Battery installation and charging (pages 6-7) in this user’s

manual.

•

Troubleshooting

Appendix

16

La page est en cours de chargement...

AT&T TL86009 Manuel utilisateur

AT&T TL86009 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents