Whirlpool WVU57UC0FS0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: WVU57UC0FS0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

WVU57UC6FS0

30" (76.2 CM) AND 36" (91.4 CM) RANGE HOOD

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories or service, call: 1-800-253-1301

or visit our website at www.whirlpool.com

In Canada, call 1-800-807-6777 or visit our website at www.whirlpool.ca

HOTTE D’ASPIRATION DE

30" (76,2 CM) ET 36" (91,4 CM)

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web à

www.whirlpool.ca

Table of Contents/Table des matières.............................................................................2

LIB0120490/W10907171A

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONL

IMPOR

TANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISA

TION RÉSIDENTIELLE UNIQUEMENT

Models/Modèles:

WVU57UC0F/WVU57UC6F

TABLE OF CONTENTS TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS .................................................5

Tools and Parts ............................................................................. 5

Location Requirements ................................................................5

Venting Requirements ..................................................................6

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ...................................................8

Prepare Location ..........................................................................8

Prepare Range Hood .................................................................10

Install Range Hood .....................................................................12

Make Electrical Connection .......................................................13

Complete Installation .................................................................14

RANGE HOOD USE ......................................................................14

Range Hood Controls ................................................................14

RANGE HOOD CARE ...................................................................15

Cleaning .....................................................................................15

WIRING DIAGRAM .......................................................................16

ASSISTANCE OR SERVICE .........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories ................................................................................17

WARRANTY ..................................................................................18

SÉCURITÉ DE LA HOTTE ............................................................20

EXIGENCES D’INSTALLATION ...................................................22

Outils et pièces ...........................................................................22

Exigences d’emplacement .........................................................22

Exigences concernant l’évacuation ...........................................23

Spéciﬁcations électriques ..........................................................24

INSTRUCTIONS D’INSTALLATION .............................................25

Préparation de l’emplacement ...................................................25

Préparation de la hotte ...............................................................27

Installation de la hotte ................................................................29

Raccordement électrique ...........................................................30

Terminer l’installation ..................................................................31

UTILISATION DE LA HOTTE .......................................................31

Commandes de la hotte.............................................................31

ENTRETIEN DE LA HOTTE .........................................................32

Nettoyage ...................................................................................32

SCHÉMA DE CÂBLAGE ...............................................................33

ASSISTANCE OU SERVICE .........................................................34

Aux É.-U. ....................................................................................34

Au Canada ..................................................................................34

Accessoires ................................................................................34

GARANTIE .....................................................................................35

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

■ Drill

■ 1¹⁄

" (3.0 cm) drill bit

■ ¹⁄

" (3.0 mm) drill bit for pilot holes

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Caulking gun and weatherproof caulking com"und

■ Flat-blade screwdriver

■ Phillips screwdriver

■ Saber or keyhole saw

■ Metal snips

Parts supplied

Remove parts from package. Check that all parts are included.

■ #8-18 x 1" (4.2 mm x 25 mm) ﬂat-head screws (2)

■ #8-18 x

" (4.2 mm x 16 mm) truss-head screws (4)

■ Drywall anchors (2)

■ Mounting brackets (2)

■

" x

" (3.5 mm x 5 mm) T10-head screws (2)

■ T10 TORX

®†

adapter (1)

■ 3

" x 10" (8.3 cm x 25.4 cm) rectangular air transition (1)

■ Regular air damper (1)

Parts needed

■ Wall or roof cap with damper to match vent system

■ 3 - UL Listed wire connectors

■ Vent clamps/duct tape as required

For 7" (17.8 cm) round vented installations:

■ 7" (17.8 cm) round metal vent system

For 3¹⁄

" x 10" (8.3 cm x 25.4 cm) rectangular vented

installations:

■ 3¹⁄

" x 10" (8.3 cm x 25.4 cm) rectangular metal vent system

For non-vented (recirculation) installations:

■ Charcoal ﬁlter kit. For information on ordering, see the

“Accessories” section.

†

TORX is a registered trademark of Acument Intellectual Properties, LLC.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation

clearances speciﬁed on the model/serial/rating plate. The

model/serial/rating plate is located inside the range hood on

the left wall.

■ Range hood location should be away from strong draft areas,

such as windows, doors, and strong heating vents.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the

cooktop/range manufacturer installation instructions before

making any cutouts.

■ This range hood is recommended for use with cooktops with

a maximum total rating of 55,000 BTUs or less.

■ Grounded electrical outlet is required. See the “Electrical

Requirements” section.

■ All openings in ceiling and wall where range hood will be

installed must be sealed.

■ These range hoods are factory set for vented installations.

Models that are capable of being installed as non-vented

(recirculating) require charcoal ﬁlters. See the “Accessories”

section to order charcoal ﬁlter kit.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

Centerline

A. 6

" (16 cm)

B. 2" (5 cm)

C. 8

" (21.3 cm)

D. 1" (2.54 cm)

E. 8

" (22.8 cm)

F. 19

" (50 cm)

G. 1

" (3.8 cm)

H. 36" (91.4 cm)

30" (76.2 cm)

" (2.2 cm)

Installation Clearances

A. 18" (45.7 cm) min. clearance - upper cabinet to countertop

B. 24" (61.0 cm) minimum - bottom of range hood to cooking surface

C. 30" (76.2 cm) min. cabinet opening width for 30" (76.2 cm) models

36" (91.4 cm) min. cabinet opening width for 36" (91.4 cm) models

D. 12" (30.5 cm) minimum cabinet depth

E. 36" (91.4 cm) base cabinet height

Venting Requirements

■ This range hood is factory set to exhaust the air to

the outside through the wall or the roof. A non-vented

(recirculating) installation will require a Charcoal Filter Kit.

See the “Accessories” section for ordering information.

■ Vent system must terminate to the outdoors, except for

nonvented (recirculating) installations.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use a 4" (10.2 cm) laundry-type wall cap.

■ Use a 7" (17.8 cm) round metal vent or a 3¹⁄

" x 10"

(8.3 cm x 25.4 cm) rectangular metal vent, depending

on your installation requirements. Rigid metal vent

is recommended. Plastic or metal foil vent is not

recommended.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efﬁcient performance.

For the most efﬁcient and quiet operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use clamps or duct tape to seal all joints in the vent system.

■ The vent system must have a damper. If roof or wall cap has

a damper, do not use damper supplied with the range hood.

■ Use caulking to seal exterior wall or roof opening around

the cap.

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air ﬂow and a thermal break should be installed

to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the

thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than speciﬁed CFM of

air movement. The speciﬁed CFM varies from locale to locale.

Consult your HVAC professional for speciﬁc requirements in your

area.

Venting Methods

Vent system can terminate either through the roof or wall. Use

3¹⁄

" x 10" (8.3 cm x 25.4 cm) rectangular with a maximum vent

length of 35 ft (10.7 m) or 7" (17.8 cm) or larger round vent with

a maximum length of 50 ft (15.2 m) for vent system.

NOTE: Flexible vent is not recommended. Flexible vent creates

both back pressure and air turbulence that greatly reduce

performance.

A. 7" (17.8 cm) round vent through roof or 3

⁄

" x 10"

(8.3 cm x 25.4 cm) rectangular vent through the roof

or wall (purchased separately)

B. Roof/Wall cap with damper (purchased separately)

C. 24" (61.0 cm) min. above the cooking surface

D. Charcoal Filter Kit (purchased separately)

E. Recirculating grid

Roof Venting Wall Venting Recirculating

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

7" (17.8 cm) Round Vent System

Vent Piece Round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

7" (17.8 cm) wall cap 0.0 ft

(0.0 m)

3¹⁄

" x 10" (8.3 cm x 25.4 cm)

to 7" (17.8 cm)

4.5 ft

(1.4 m)

3¹⁄

" x 10" (8.3 cm x 25.4 cm)

to 7" (17.8 cm) 90° elbow

5.0 ft

(1.5 m)

Example vent system

Maximum Recommended Length = 50 ft (15.2 m)

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of 7" (17.8 cm) system = 13.0 ft (3.9 m)

3¹⁄

" x 10" (8.3 cm x 25.4 cm) Vent System

Vent Piece

3¹⁄

" x 10" (8.3 cm x 25.4 cm)

90° elbow

5.0 ft

(1.5 m)

3¹⁄

" x 10" (8.3 cm x 25.4 cm)

ﬂat elbow

12.0 ft

(3.7 m)

3¹⁄

" x 10" (8.3 cm x 25.4 cm)

wall cap

0.0 ft

(0.0 m)

Example vent system

Maximum Recommended Length = 35 ft (10.7 m)

1 - 90° elbow = 5.0 ft (1.5 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

1 - wall cap = 0.0 ft (0.0 m)

Length of 3¹⁄

" x 10" (8.3 cm x 25.4 cm)

system

= 13.0 ft (3.9 m)

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

all cap

7" (17.8 cm) round

90˚ elbow

2 ft (0.6 m)

6 ft (1.8 m)

Wall cap

" x 10"

(8.3 x 25.4 cm)

elbow

2 ft

(0.6 m)

6 ft (1.8 m)

■ A 120-volt, 60 Hz., AC-only, 15-amp, fused electrical circuit

is required.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL Listed for joining copper to aluminum.

Follow the electrical connector manufacturer’s recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as speciﬁed on the model/serial/rating plate.

The model/serial/rating plate is located inside the range hood

on the left wall.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATION INSTRUCTIONS

Prepare Location

NOTE: It is recommended that the vent system be installed

before hood is installed.

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

1. Disconnect "wer.

2. Depending on your model, determine which venting method

to use: roof, wall, or non-vented (recirculating).

3. Select a ﬂat surface for assembling the range hood. Place

covering over that surface.

4. Lift the range hood and set it upside down onto covered

surface.

Determine Wiring Hole Location

Cut only one 1¹⁄

" (3.2 cm) diameter wiring access hole.

1. Determine and clearly mark a vertical centerline on the wall

and cabinet in the area the vent opening will be made.

A. Centerline

To wire through top:

1. Mark a line distance “A” from the right of the centerline

on the underside of the cabinet. For 12" (30.5 cm) deep

cabinets, mark the "int on this line that is 2" (5.1 cm) from the

back wall. For 15" (38.1 cm) deep cabinets, mark the point

on this line that is 5" (12.7 cm) from the back wall. Drill a 1¼"

(3.2 cm) diameter hole through the cabinet at this "int.

To wire through wall:

1. Mark a line distance “A” from the right of the centerline on

the underside of the wall. Mark the point on this line that is

⁄

" (2.2 cm) from the underside of the cabinet. Drill a 1¹⁄

(3.2 cm) diameter hole through the rear wall at this "int.

A. 8³⁄

" (21.3 cm)

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

Centerline

⁷⁄₈" (2.2 cm

)

Centerline

A. 8³⁄

" (21.3 cm)

B. 2" (5.1 cm) for 12" (30.5 cm) deep cabinets*

5" (12.7 cm) for 15" (38.1 cm) deep cabinets*

*From wall, not cabinet frame

Style 1 - Cut Openings for 3¼" x 10"

(8.3 cm x 25.4 cm) Rectangular Vent System

Roof Venting

To make a 4¹⁄

" x 10½" (10.8 cm x 26.7 cm) rectangular

cutout on the underside of cabinet top and bottom:

1. Mark lines ¹⁄

" (1.3 cm) and 4³⁄

" (12.1 cm) from the back wall

on the centerline of the underside of cabinet.

2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline

on the underside of cabinet.

3. Use saber or keyhole saw to cut a rectangular opening for

vent.

4. Repeat steps 1-3 for the underside of the top of the cabinet.

Wall Venting

To make a 3½" x 10½" (8.9 cm x 26.7 cm) rectangle in the

wall:

1. Make 2 lines by measuring ³⁄

" (0.9 cm) and 3

⁄

" (9.8 cm)

down from underside of cabinet and mark on the centerline

on the back wall.

2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline

on the wall.

3. Use saber or keyhole saw to cut a rectangular opening in the

wall for the vent.

Style 2 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm)

Rectangular Vent to Round Vent Transition

Roof Venting

To make a 4¹⁄

" x 10½" (10.8 cm x 26.7 cm) rectangular

cutout on the underside of cabinet bottom:

1. Mark lines ¹⁄

" (1.3 cm) and 4³⁄

" (12.1 cm) from the back wall

on the centerline of the underside of cabinet.

2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline

on the underside of cabinet.

3. Use saber or keyhole saw to cut a rectangular opening for

vent.

To make a circular vent opening on the underside of the

cabinet top:

1. Mark a centerline on the underside of the top of cabinet.

2. Mark a line 5" (12.7 cm) from the back wall on the underside

of the top of cabinet.

3. Use a compass or a circle template to draw a circle with a

diameter that is ¼" (0.64 cm) larger than the vent.

4. Use saber or keyhole saw to cut the circular vent opening.

Style 3 - Cut Openings for 7" (17.8 cm) Round Vent

To make a circular vent openings on the underside of the

cabinet top and bottom:

1. Mark a centerline on the underside of the top of cabinet.

2. Mark a line 5" (12.7 cm) from the back wall on the underside

of the top and bottom of cabinet.

3. Use a compass or a circle template to draw a circle with a

diameter that is ¼" (0.64 cm) larger than the vent.

4. Use saber or keyhole saw to cut the circular vent opening.

⅜"

3⅞"

Cabinet

front

(0.9 cm)

(9.8 cm)

5¼"

(13.3 cm)

Centerline

5¼"

(13.3 cm)

*From wall, not cabinet frame

" (1.3 cm)*

B. 4

" (12.1 cm)*

*From wall, not cabinet frame

Cabinet cutouts

" (1.3 cm)*

B. 4

" (12.1 cm)*

*From wall, not

cabinet frame

A. 5" (12.7 cm)*

Circular vent opening

Cabinet

cutouts

*From wall, not

cabinet frame

A. 5" (12.7 cm)*

Install Vent System

1. Install vent through the vent opening in upper cabinet or wall.

Complete venting system according to the selected venting

method. See the “Venting Requirements” section.

2. Use caulking to seal exterior wall or roof opening around

the cap.

Prepare Range Hood

Only for venting through the top/wall options:

1. Remove vent knockouts, depending on your installation

requirements.

A. Round vent knockout

B. Top rectangular vent knockout

C. Rear rectangular vent knockout

Round vent system installations - Remove top rectangular and

round vent knockouts.

Rectangular vent system installations - For roof installations,

remove the top rectangular vent knockout. For wall installations,

remove the rear rectangular vent knockout.

Non-vent (recirculating) installations - Do not remove any

knockouts.

2. Install 7" (17.8 cm) round vent mounting plate or 3¹⁄

" x 10"

(8.3 cm x 25.4 cm) vent damper, depending on your vent

system installation. Attach to range hood with 3.5 x 9.5 mm

screws provided and remove the tape from the damper ﬂap.

NOTE: An optional 7" (17.8 cm) round damper is also

available as an accessory. For information on ordering,

see the “Accessories” section.

A. 7" (17.8 cm) round damper

(See the “Accessories” section)

B. 3.5 x 9.5 mm screws

C. 7" (17.8 cm) round vent mounting plate

D. Round vent knockout

E. Rectangular vent knockout

NOTE: The round vent damper may only be installed on the top

of the product.

A. Vertical air transition

B. 3.5 x 9.5 mm screws

C. Vent knockouts

D. Horizontal air transition

Only for recirculating options

For this venting method, it is neccesary to purchase a Charcoal

Filter Kit. See the “Accessories” section for ordering.

1. Remove each ﬁlter by pulling the spring-release handle and

then pulling down the ﬁlter.

2. Remove the venting method screw from the Vented option

with a T10 TORX

screwdriver and set aside.

A. Venting method screw

3. Slide the venting lever down as shown in the following

image.

A. Lever on No Vented option

4. Replace the venting method screw on the No Vented

(recirculating) option.

A. No Vented method screw

5. Remove the no vented (recirculating) vent cover.

A. Non-vented (recirculating) vent cover

6. Bend spring clips away from metal grease ﬁlter.

7. Place charcoal ﬁlter into top side of metal ﬁlter.

8. Bend spring clips back into place to secure the charcoal ﬁlter

to the metal ﬁlter.

9. Replace metal grease ﬁlter.

Install Range Hood

1. Remove the power supply knockout from the top or rear of

the vent hood (depending on the incoming location of your

home power supply cable) and install a UL Listed or CSA

Approved ¹⁄

" strain relief.

A. Power supply knockout

2. Align the exterior edge of the mounting brackets with the

exterior edges of the upper cabinet.

IMPORTANT: The brackets should touch the upper cabinet.

With a pencil, mark the upper holes on the brackets.

3. Using a #2 Phillips screwdriver, install the drywall anchors.

Using #8-18 x 1" (4.2 x 25 mm) ﬂat-head #2 Phillips screws,

install the mounting brackets using the upper holes.

NOTE: For installation to a surface other than drywall, it

is recommended that a qualiﬁed contractor determine the

anchoring method.

4. Lift the range hood into place and insert the mounting

bracket tabs through the slots in the back of the range hood.

5. From the inside of the range hood, start a #8-18 x

⁄

(4.2 x 16 mm) truss-head screw into the mounting tab (A) on

each side of the range hood as shown in the following inset.

Insert the screws approximately 2 turns into the mounting

tab holes. Bend each mounting tab upward approximately

45°.

6. Lift the range hood into place, positioning the rear slots over

the mounting brackets.

7. Using a Phillips screwdriver, push on the screws that are

started into the top mounting tabs and bend the tabs against

the cabinet side walls. Attach the screws to the cabinet side

walls.

8. For direct wire installations, run the home power supply

cable according to the National Electric Code or CSA

standards and local codes and ordinances. There must be

enough wiring from the fused disconnect (or circuit breaker)

box to make the connection in the range hood electrical

terminal box.

9. Tighten the strain relief screws.

NOTE: Do not reconnect power until the installation is

complete.

OPTIONAL: If you prefer, bend the rear tabs against the rear

of the range hood and attach to the wall using #8-18 x

(4.2 x 16 mm) truss-head screws.

A. Mounting tab

Connect Vent System

Connect the ventwork to the range hood. Seal joints with vent

clamps or duct tape to make secure and airtight. Check that the

backdraft dampers work properly.

Power Supply Cable Installation

1. For direct wire installations, run the home power supply

cable according to the National Electric Code or CSA

standards and local codes and ordinances. There must be

enough wiring from the fused disconnect (or circuit breaker)

box to make the connection in the hood electrical terminal

box.

For optional power supply cord kit (see the “Accessories”

section), follow the instructions in the “Make Electrical

Connections” section.

NOTES:

■ Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this

model range hood.

■ Do not reconnect power until the installation is complete.

2. Remove the screw from the terminal box cover. Remove

terminal box cover and set aside.

A. Terminal box cover

B. Screw

Make Electrical Connection

Option 1 - Direct Wire Installations

1. Disconnect power.

A. White wires

B. Black wires

C. UL Listed wire connector

D. Green (or bare) ground wire

E. Home power supply cable or

power cord accessory kit

F. UL Listed or CSA Approved

½" strain relief

G. Green ground screw

2. Use UL Listed wire connectors and connect white wires (A)

together.

3. Use UL Listed wire connectors and connect black wires (B)

together.

4. Connect green (or bare) ground wire from power supply to

green ground screw in terminal box and securely tighten.

5. Install terminal box cover.

6. Reconnect power.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

WARNING

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

Option 2 - Power Cord Kit Installations

For optional power cord kit installations, follow the instructions

supplied with the power cord kit. See the “Accessories” section

for information on ordering.

NOTE: Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this model

range hood.

Complete Installation

1. Replace grease ﬁlter if removed. See the “Range Hood Care”

section.

2. Check the operation of the range hood fan and light. See the

“Range Hood Use” section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect "wer and check wiring connections.

NOTE: To get the most efﬁcient use from your new range hood,

read the “Range Hood Use” section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors,

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after

the cooking is complete to clear all smoke and odors from the

kitchen.

The hood controls are located on the front panel of the range

hood.

Range Hood Controls

NOTE: The control buttons will light up when the range hood

is ON.

Light button

Press LIGHT once to turn the LED lights on.

Press LIGHT again to turn the LED lights off.

Boost button

Press BOOST to turn the fan on at the highest speed. Boost will

automatically turn off after 10 minutes and the fan will switch to

high speed.

High button

Press HIGH to turn the fan on at high speed.

Med button

Press MED to turn the fan on at medium speed.

Low button

Press LOW to turn the fan on at low speed.

Off button

Press OFF to turn the fan off at any speed.

Timer

The range hood can be set to automatically turn off after

15 minutes.

Press and hold the desired fan speed button (C, D, or E in the

previous image) for 3 seconds. The fan will run on the chosen

speed for 15 minutes and the fan speed button light will ﬂash

continuously. After 15 minutes, the fan will turn off automatically.

To cancel the timer, press a different fan speed button while the

timer is running.

Grease Filter Timer

The grease ﬁlter timer can remind you when to clean or replace

the grease ﬁlter. It is OFF by default.

■ To enable the grease ﬁlter timer, push and hold the Low

button and the Off button at the same time for 3 seconds

while the range hood is OFF. Repeat to disable the function.

■ After 40 hours of fan use, the Off button will begin to blink.

The blinking light indicates that the grease ﬁlter should be

cleaned.

■ To reset the grease ﬁlter timer, press and hold OFF for

3 seconds.

A. Blower and light touch control

B. LED lamps

C. Filter retainer

D. Grease ﬁlter

A. Light button

B. Boost button

C. High Speed button

D. Medium Speed button

E. Low Speed button

F. Off button

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease ﬁlters frequently

according to the following instructions. Replace grease ﬁlter

before operating hood.

Exterior Surfaces

IMPORTANT: Do not use soap-ﬁlled scouring pads, abrasive

cleaners, cooktop polishing creme, steel wool, gritty washcloths

or paper towels.

To avoid damage to the stainless steel, do not use cleaners that

contain chlorine.

Cleaning Method:

■ Rub in direction of grain to avoid scratching or damaging the

surface.

■ For stainless steel models, Stainless Steel Cleaner and "lish

Part Number 31462A (not included):

See the “Assistance or Service” section to order.

■ Liquid detergent or all-purpose cleaner:

Rinse with clean water and dry with soft, lint-free cloth.

■ Glass cleaner to remove ﬁngerprints.

Metal Grease Filter

For vented installations:

1. Remove each ﬁlter by pulling the spring-release handle and

then pulling down the ﬁlter.

A. Spring-release handle

2. Wash metal ﬁlter as needed in dishwasher or hot detergent

solution.

3. Reinstall the ﬁlter by making sure the spring-release handles

are toward the front. Insert aluminum ﬁlter into upper track.

4. Push in spring-release handle.

5. Push up on metal ﬁlter and release handle to latch into place.

6. Repeat steps 1-5 for the other ﬁlter.

For non-vented (recirculating) installations:

The charcoal ﬁlter is not washable. It should last up to 6 months

with normal use. Replace with Charcoal Filter Kit. See the

“Assistance or Service” section for information on ordering.

Replacing an LED Lamp

The LED lights are replaceable by a service technician only. See

the “Warranty” section for service contact information.

WIRING DIAGRAM

SEL0120632

YL/GN

MOTOR SPECIFICATIONS

POWER SUPPLY

FREQUENCY

POWER ABSORTION

120 VAC

60 HZ

210 W

(SPEED4) BLUE / BLACK

(SPEED3) BLUE / GREY

(SPEED2) BLUE / RED

(SPEED1) BLUE / WHITE

18uF

LED

LED DRIVER

OUTPUT:700mA (2-15 VDC)

INPUT: 120 VAC

User Interface

GND

YL/GN

EMI

FILTER

FUSE

RL1

RL2

RL4

ECB0089090

RL3

31.1

35.5

45.0

55.0

MOTOR RESISTANCE (Ω)

OUTPUT VOLTAGE:

120 VAC

ASSISTANCE OR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that

you use only factory speciﬁed parts. Factory speciﬁed parts will

ﬁt right and work right because they are made with the same

precision used to build every new appliance.

To locate factory speciﬁed replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call the Whirlpool Customer eXperience Center toll free:

1-800-253-1301 or visit our website at www.whirlpool.com.

Our consultants provide assistance with:

■ Scheduling of service. Whirlpool designated service

technicians are trained to fulﬁll the product warranty and

provide after-warranty service, anywhere in the United

States.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-800-807-6777 or visit our webpage www.whirlpool.ca.

Our consultants provide assistance with:

■ Scheduling of service. Whirlpool designated service

technicians are trained to fulﬁll the product warranty and

provide after-warranty service, anywhere in Canada.

■ Features and speciﬁcations on our full line of appliances.

■ Referrals to local Whirlpool dealers.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulﬁll the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Centre

Whirlpool Canada LP

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Stainless Steel Cleaner and Polish

Order Part Number 31462A

Charcoal Filter Kit

For 30" (76.2 cm) models, order Part Number W10905734

For 36" (91.4 cm) models, order Part Number W10905735

Power Cord Kit

Order Part Number W10613691

7" (17.8 cm) Round Damper

Order Part Number W10355451

7" Round Damper Vent Mounting Plate

Order Part Number W10388168

11/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and

Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

WHIRLPOOL

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For one year from the date of purchase,

when this major appliance is installed,

operated and maintained according to

instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory

Speciﬁed Replacement Parts and repair

labor to correct defects in materials or

workmanship that existed when this

major appliance was purchased, or at

its sole discretion replace the product.

In the event of product replacement,

your appliance will be warranted for

the remaining term of the original unit’s

warranty period.

YOUR SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT

REPAIR AS PROVIDED HEREIN.

Service must be provided by a

Whirlpool designated service company.

This limited warranty is valid only in

the United States or Canada and

applies only when the major appliance

is used in the country in which it was

purchased. This limited warranty is

effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain

service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user, operator or

installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in accordance with

electrical or plumbing codes or correction of household electrical or plumbing (i.e. house wiring, fuses

or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water ﬁlters, preservation solutions, etc.).

5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of products from natural gas or L.P. gas.

7. Damage from accident, misuse, abuse, ﬁre, ﬂoods, acts of God or use with products not approved by

Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized service,

alteration or modiﬁcation of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance ﬁnishes

unless such damage results from defects in materials and workmanship and is re"rted to Whirlpool

within 30 days.

10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive environments including

but not limited to high salt concentrations, high moisture or humidity or ex"sure to chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized Whirlpool

servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in ﬁxtures (i.e. trim, decorative panels,

ﬂooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing, removal or

replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered or not easily

determined.

The cost of repair or replacement under these excluded circumstances shall be borne by

the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or ﬁtness, so this limitation may not apply to you. This warranty gives you speciﬁc

legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you

should ask Whirl"ol or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of

incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you speciﬁc legal rights, and you

also may have other rights that vary from state to state or province to province.

www.whirlpool.com/product_help

W10907171A

9/16

11/14

CLAUSE D’EXONÉRATION DE RESPONSABILITÉ AU TITRE DES GARANTIES IMPLICITES

LES GARANTIES IMPLICITES, Y COMPRIS LES GARANTIES APPLICABLES DE QUALITÉ MARCHANDE OU D’APTITUDE À UN USAGE

PARTICULIER, SONT LIMITÉES À UN AN OU À LA PLUS COURTE PÉRIODE AUTORISÉE PAR LA LOI. Certains États et provinces ne permettent

pas de limitation sur la durée des garanties implicites de qualité marchande ou d’aptitude à un usage particulier, de sorte que la limitation ci-dessus

peut ne pas être applicable dans votre cas. Cette garantie vous confère des droits juridiques spéciﬁques et vous pouvez également jouir d’autres

droits qui peuvent varier d’une juridiction à l’autre.

EXONÉRATION DE RESPONSABILITÉ DANS LES DOMAINES NON COUVERTS PAR LA GARANTIE

Whirlpool décline toute responsabilité au titre de la qualité, de la durabilité ou en cas de dépannage ou de réparation nécessaire sur ce gros appareil

ménager autre que les responsabilités énoncées dans la présente garantie. Si vous souhaitez une garantie plus étendue ou plus complète que la

garantie limitée fournie avec ce gros appareil ménager, adressez-vous à Whirlpool ou à votre détaillant pour obtenir les modalités d’achat d’une

garantie étendue.

LIMITATION DES RECOURS; EXCLUSION DES DOMMAGES FORTUITS OU INDIRECTS

LE SEUL ET EXCLUSIF RECOURS DU CLIENT DANS LE CADRE DE LA PRÉSENTE GARANTIE LIMITÉE CONSISTE EN LA RÉPARATION PRÉVUE

PAR LA PRÉSENTE. WHIRLPOOL N’ASSUME AUCUNE RESPONSABILITÉ POUR LES DOMMAGES FORTUITS OU INDIRECTS. Certains États

et certaines provinces ne permettent pas l’exclusion ou la limitation des dommages fortuits ou indirects de sorte que ces limitations et exclusions

peuvent ne pas être applicables dans votre cas. Cette garantie vous confère des droits juridiques spéciﬁques et vous pouvez également jouir

d’autres droits qui peuvent varier d’une juridiction à l’autre.