Hilti SSH 6-A22 Mode d'emploi

Marque: Hilti

Modèle: SSH 6-A22

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

SSH 6A22

English 1

Français 11

Español 22

Português 33

SSH 6A22

en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

*2253584*

2253584 English 1

Original operating instructions

1 Information about the documentation

1.1 About this documentation

• Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free

handling and use of the product.

• Observe the safety instructions and warnings in this documentation and on the product.

• Always keep the operating instructions with the product and make sure that the operating instructions

are with the product when it is given to other persons.

1.2 Explanation of symbols used

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶ Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶ Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶ Draws attention to a potentially dangerous situation that could lead to slight personal injury or damage

to the equipment or other property.

1.2.2 Symbols in the documentation

The following symbols are used in this document:

Read the operating instructions before use.

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

1.2.3 Symbols in the illustrations

The following symbols are used in illustrations:

These numbers refer to the corresponding illustrations found at the beginning of these operating

instructions

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text

Item reference numbers are used in the overview illustrations and refer to the numbers used in

the product overview section

This symbol is intended to draw special attention to certain points when handling the product.

2 English 2253584

*2253584*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

The product supports wireless data transmission compatible with iOS and Android platforms.

Li-ion battery

Hilti Li-ion battery type series used. Observe the information given in the section headed In-

tended use.

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

Direct current (DC)

Wear eye protection

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶ Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Slitting shear SSH 6-A22

Generation: 01

Serial no.:

1.5 Declaration of conformity

We declare, on our sole responsibility, that the product described here complies with the applicable directives

and standards. A copy of the declaration issued by the certification department can be found at the end of

this documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶ Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

*2253584*

2253584 English 3

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶ Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶ Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶ Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶ Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶ Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶ Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

4 English 2253584

*2253584*

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶ Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶ Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶ Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Battery use and care

▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion

batteries.

▶ Do not expose batteries to high temperatures, direct sunlight or fire.

▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.

▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height

or show signs of damage. In this case, always contact your Hilti Service.

▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable

location, well away from flammable materials, where it can be kept under observation and allowed to

cool down. In this case, always contact your Hilti Service.

2.3 Additional safety instructions

Personal safety

▶ Wear protective gloves. The cut edges and metal swarf are sharp-edged and there is a risk of cut injuries.

The product and the workpiece become hot in the working process and there is a risk of burn injuries.

▶ Touch the power tool by the insulated gripping surfaces only, when carrying out work in which the

accessory tool can come into contact with concealed wiring.

▶ Take breaks between working and do relaxation and finger exercises to improve the blood circulation in

your fingers.

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

Electrical safety

▶ Have dirtied or dusty power tools that are used frequently for working on conductive materials checked

at regular intervals by Hilti Service. Dust (especially dust from conductive materials) or dampness on the

surface of the power tool can, under unfavorable conditions, lead to electric shock.

▶ Clean the ventilation slots on the power tool at regular intervals. The motor’s fan draws dust into the

housing and a build-up of metallic dust can cause electrical hazards.

▶ Before beginning work, check the working area (e.g. using a metal detector) to ensure that no concealed

electric cables or gas and water pipes are present. External metal parts of the machine can become live,

for example if you inadvertently damage electric wiring.

▶ Do not attempt to cut workpieces that could be electrically live.

*2253584*

2253584 English 5

3 Description

3.1 Product overview 1

Swarf cutter

;

Lockable on/off switch

Grip

Adjusting knob for speed

Dust filter

(

Battery release button

)

Battery

Bearing pin

Blade

Cutter plate

Mark for swarf cut-off

3.2 Intended use

The product described is a hand-held, cordless slitting shear. It is designed for cutting sheet-like workpieces

out of steel, aluminum, plastic or comparable materials. It can be used to cut along a marked line, for cutting

straight or curved outside edges and for cut-outs. The strip of swarf can be cut off at any point on the

workpiece.

▶ Use only Hilti Liion batteries of the B 22 series with this product.

▶ Use only Hilti battery chargers of the C 4/36 series to charge these batteries.

3.3 Items supplied

Slitting shear, Torx wrench, operating instructions

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your local

Hilti Store or online at: www.hilti.group.

Before being dispatched, the product was tested to ensure that it is in full working order. There

workpiece used in testing might have left tiny scratches in the surface of the housing.

3.4 Temperature-dependent motor protection

The temperature-dependent motor protection system monitors current input and motor temperature and

thus prevents the power tool overheating.

If the motor is overloaded through application of excessive working pressure, the power tool’s performance

drops noticeably or it may stall completely.

If the power tool stalls or slows significantly due to overloading, release the pressure applied to the tool and

then allow it to run under no load for approx. 30 seconds.

3.5 Charge status indicator of the Li-ion battery

The charge status of the Liion battery is displayed after one of the two battery release buttons is pressed.

Status Meaning

4 LEDs light up. Charge status: 75 % to 100 %

3 LEDs light up. Charge status: 50 % to 75 %

2 LEDs light up. Charge status: 25 % to 50 %

1 LED lights up. Charge status: 10 % to 25 %

1 LED flashes. Charge status: < 10 %

Indication of the charge status is not possible while the power tool is in operation or immediately

after operation. If the battery charge status LEDs flash, please refer to the information given in the

Troubleshooting section.

6 English 2253584

*2253584*

4 Technical data

Rated voltage

21.6 V

Stroke rate at idle speed

1,185 /min … 2,680 /min

Weight including battery B22⁄8.0

3.3 kg

(7.3 lb)

Ambient temperature for operation

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 70 ℃

(−4 ℉ … 158 ℉)

4.1 Battery

Battery operating voltage

21.6 V

Ambient temperature for operation

−17 ℃ … 60 ℃

(1 ℉ … 140 ℉)

Storage temperature

−20 ℃ … 40 ℃

(−4 ℉ … 104 ℉)

Battery charging starting temperature

−10 ℃ … 45 ℃

(14 ℉ … 113 ℉)

4.2 Blade

Blades of different types are needed, depending on the thickness or strength of the material to be cut. Select

the correct blade for the purpose from the table below.

The blades have two cutting edges. The cutting edges cannot be resharpened.

Initial equipment, as supplied ex works: SSHCS 1.5  2.5 mm

SSHCS,

0.5  1.5 mm,

, for

straight cuts

SSHCS,

1.5  2.5 mm,

, for

straight cuts

SSHCX,

0.5  1.5 mm,

, for

straight cuts

in stainless

steel

SSHCC,

0.5  1.5 mm,

, for curves

SSHCD,

4 x 0.9 mm,

, for spiral

ducting

Permissible steel

thickness, steel

up to 400 N⁄mm²

1.5 mm

(0.06 in) 16 ga

2.5 mm

(0.10 in) 13 ga

•/• 1.5 mm

(0.06 in) 16 ga

•/•

Permissible steel

thickness, steel

up to 600 N⁄mm²

1.0 mm

(0.04 in) 20 ga

•/• 1.5 mm

(0.06 in) 16 ga

0.8 mm

(0.03 in) 22 ga

•/•

Permissible ma-

terial thickness,

aluminum up to

250 N⁄mm²

2.0 mm

(0.08 in) 12 ga

3.0 mm

(0.12 in) 9 ga

•/• 2.0 mm

(0.08 in) 12 ga

•/•

Permissible

material

thickness, steel

spiral ducting up

to 400 N⁄mm²

•/• •/• •/• •/• 4 x 0.9 mm

(4 x 0.035 in)

4 x 20 ga

Permissible

material

thickness, steel

spiral ducting up

to 600 N⁄mm²

•/• •/• •/• •/• 4 x 0.6 mm

(4 x 0.024 in)

4 x 24 ga

*2253584*

2253584 English 7

SSHCS,

0.5  1.5 mm,

, for

straight cuts

SSHCS,

1.5  2.5 mm,

, for

straight cuts

SSHCX,

0.5  1.5 mm,

, for

straight cuts

in stainless

steel

SSHCC,

0.5  1.5 mm,

, for curves

SSHCD,

4 x 0.9 mm,

, for spiral

ducting

Starting hole di-

ameter

17 mm

(0.7 in)

22 mm

(0.9 in)

20 mm

(0.8 in)

15 mm

(0.6 in)

18 mm

(0.7 in)

Smallest radius

for curved cut-

outs

80 mm

(3.1 in)

150 mm

(5.9 in)

120 mm

(4.7 in)

L 45 mm (2 in),

R 80 mm

(3.15 in)

150 mm

(5.9 in)

5 Preparations at the workplace

CAUTION

Risk of injury by inadvertent starting!

▶ Before inserting the battery, make sure that the product is switched off.

▶ Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery.

5.2 Inserting the battery

CAUTION

Risk of injury by short circuit or falling battery!

▶ Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶ Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the battery holder until it engages with an audible click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the tool.

6 Operation

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Setting the cutting speed

▶ Set the cutting speed by turning the adjusting knob for motor speed.

6.2 Switching on

1. Press the rear section of the on/off switch.

2. Slide the on/off switch forward.

➥ The motor runs.

3. Lock the on/off switch.

8 English 2253584

*2253584*

6.3 Cutting 2

Before starting work, check that the cutting rails and the cut-off plate are correctly and securing seated

and check the tightening torques of the corresponding securing screws.

1. Switch the product on. → page 7

2. Guide the product through the material to be cut while holding the product at an angle of about 14 ° to

the material.

Always use a sharp blade and turn or change the cutting rails in good time.

Apply cutting oil or other cooling lubricant to the workpiece to prolong the useful life of the cutting

tools.

3. If the following conditions are met, also take this action:

Conditions: Cutting curves

▶ Guide the product slowly through the material, following the applicable radius.

Do not tilt the product to the side.

4. To end the cut, switch the product off.

6.4 Cutting off swarf 3

Do not cut off short lengths of swarf. The minimum length of the strip of swarf cut off must be one

complete curl.

Marks on the front of the housing indicate the cut-off position.

1. With the product switched on, press the swarf cutter for 0.5 of a second.

➥ The strip of swarf is cut off at the mark and the cut-off process stops automatically.

2. Remove the cutting of swarf by hand.

6.5 Switching off

▶ Press the rear section of the on/off switch.

➥ The on/off switch jumps into the off position and the motor stops.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶ Always remove the battery before carrying out care and maintenance tasks!

Care and maintenance of the tool

• Carefully remove any dirt that may be adhering to parts.

• Remove the dust filter and clean it and the air vents carefully, using a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Care of the lithiumion batteries

• Keep the battery free from oil and grease.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these may attack the plastic parts.

• Avoid ingress of moisture.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

*2253584*

2253584 English 9

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

7.1 Changing the blade 4

ATTENTION

Risk of damage to workpiece and blade!

▶ Always select the correct blade for the planned use and thickness of material to be cut.

Change the blade when it becomes blunt and cutting performance diminishes.

Always replace the blade whenever you install new cutting rails.

1. Press out the bearing pin.

2. Pull the blade out of the cutting head.

3. Lightly grease the bearing pin and the new blade.

4. Insert the new blade.

5. Push the bearing pin into the hole until it engages.

7.2 Changing the cutting rails 5

CAUTION

Risk of damage to product and cutting tools!

▶ Clean the threads before installing the securing screws.

▶ Always use the new securing screws supplied and tighten the screws to the specified tightening torque.

1. Remove the securing screws and remove the cutting rails. If necessary, insert a suitable tool through the

cutting head from above and push the cutting rails out of the guide.

2. Clean the thread.

3. Check the cutting rails:

➥ If the cutting rails are blunt along only one half, reinstall them turned through 180°.

➥ When either one of the two cutting rails is blunt along both halves, replace the two cutting rails as a

pair.

4. Insert the cutting rails and install the securing screws.

Technical data

Tightening torque 5 Nm

(4 ftlb

)

7.3 Changing the cut-off plate 6

CAUTION

Risk of damage to product and cutting tools!

▶ Clean the threads before installing the securing screws.

▶ Always use the new securing screws supplied and tighten the screws to the specified tightening torque.

1. Remove the securing screw and remove the cut-off plate.

2. Clean the thread.

3. Insert the new cut-off plate and install the new securing screw.

Technical data

Tightening torque 5 Nm

(4 ftlb

)

10 English 2253584

*2253584*

8 Transport and storage of cordless tools

Transport

CAUTION

Accidental starting during transport !

▶ Always transport your products with the batteries removed!

▶ Remove the battery.

▶ Never transport batteries in bulk form (loose, unprotected).

▶ Check the tool and batteries for damage before use after long periods of transport.

Storage

CAUTION

Accidental damage caused by defective or leaking batteries !

▶ Always store your products with the batteries removed!

▶ Store the tool and batteries in a place that is as cool and dry as possible.

▶ Never store batteries in direct sunlight, on heating units or behind a window pane.

▶ Store the tool and batteries in a place where they cannot be accessed by children or unauthorized

persons.

▶ Check the tool and batteries for damage before use after long periods of storage.

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

Trouble or fault Possible cause Action to be taken

The battery runs down more

quickly than usual.

Very low ambient temperature. ▶ Allow the battery to warm up

slowly to room temperature.

The battery does not engage

with an audible click.

The retaining lugs on the battery

are dirty.

▶ Clean the retaining lugs and refit

the battery.

1 LED flashes.

The power tool does not

work.

Low battery. ▶ Change the battery and charge

the empty battery.

The battery is too hot or too cold. ▶ Allow the battery to cool down

or warm up slowly to room

temperature.

All 4 LEDs flash.

The power tool does not

work.

The power tool has been over-

loaded.

▶ Release the control switch and

then press it again. Then allow

the power tool to run under no

load for approx. 30 seconds.

The power tool or battery

gets very hot.

Electrical fault ▶ Switch the power tool off im-

mediately, remove the battery,

keep it under observation, allow

it to cool down and contact Hilti

Service.

The power tool does not de-

velop full power.

A battery with inadequate capacity

was used.

▶ Use a battery with adequate

capacity.

Diminishing cutting perfor-

mance

Blade and / or cutting rails are

blunt.

▶ Change the blade. → page 9

▶ Change the cutting rails.

→ page 9

The motor has no braking

effect.

Low battery. ▶ Change the battery and charge

the empty battery.

The power tool was overloaded

briefly.

▶ Switch the power tool off and

then on again.

*2253584*

2253584 Français 11

10 Disposal

Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The

materials must be correctly separated before they can be recycled. In many countries, your old tools,

machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative

for further information.

Battery disposal

Improper disposal of batteries can result in health hazards from leaking gases or fluids.

▶ DO NOT send batteries through the mail!

▶ Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶ Dispose of your battery out of the reach of children.

▶ Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

▶ Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶ Please contact your local Hilti representative if you have questions about the warranty conditions.

Notice d'utilisation originale

1 Indications relatives à la documentation

1.1 À propos de cette documentation

• Lire intégralement la présente documentation avant la mise en service. C'est la condition préalablement

requise pour assurer la sécurité du travail et un maniement sans perturbations.

• Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que

celles figurant sur le produit.

• Toujours conserver le mode d'emploi à proximité du produit et uniquement le transmettre à des tiers

avec ce mode d'emploi.

1.2 Explication des symboles

1.2.1 Avertissements

Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de

signalisation suivants sont utilisés :

DANGER

DANGER !

▶ Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la mort.

AVERTISSEMENT

AVERTISSEMENT !

▶ Pour un danger potentiel qui peut entraîner de graves blessures corporelles ou la mort.

ATTENTION

ATTENTION !

▶ Pour attirer l'attention sur une situation pouvant présenter des dangers entraînant des blessures

corporelles légères ou des dégâts matériels.

1.2.2 Symboles dans la documentation

Les symboles suivants sont utilisés dans la présente documentation :

12 Français 2253584

*2253584*

Lire le mode d'emploi avant d'utiliser l'appareil

Pour des conseils d'utilisation et autres informations utiles

Maniement des matériaux recyclables

Ne pas jeter les appareils électriques et les accus dans les ordures ménagères

1.2.3 Symboles dans les illustrations

Les symboles suivants sont utilisés dans les illustrations :

Ces chiffres renvoient à l'illustration correspondante au début du présent mode d'emploi

La numérotation détermine la séquence des étapes de travail dans l'image et peut se différencier

de celles des étapes de travail dans le texte

Les numéros de position sont utilisés dans l'illustration Vue d’ensemble et renvoient aux numé-

ros des légendes dans la section Vue d'ensemble du produit

Ce signe doit inviter à manier le produit en faisant particulièrement attention.

1.3 Symboles spécifiques au produit

1.3.1 Symboles sur le produit

Les symboles suivants peuvent être utilisés sur le produit :

Le produit prend en charge la transmission de données sans fil qui est compatible avec les

plates-formes iOS et Android.

Accu lithium-ions

Série de type d'accu Li-Ion Hilti utilisée. Observer les instructions au chapitre Utilisation

conforme à l'usage prévu.

Ne jamais utiliser l'accu comme outil de percussion.

Ne pas laisser tomber l'accu. Ne pas utiliser d'accu ayant subi un choc ou d'autres dommages.

Courant continu

Porter des lunettes de protection

1.4 Informations produit

Les produits sont destinés aux professionnels et ne doivent être utilisés, entretenus et réparés

que par un personnel autorisé et formé. Ce personnel doit être spécialement instruit quant aux dangers

inhérents à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont

utilisés de manière incorrecte par un personnel non qualifié ou de manière non conforme à l'usage prévu.

La désignation du modèle et le numéro de série figurent sur sa plaque signalétique.

▶ Inscrivez le numéro de série dans le tableau suivant. Les informations produit vous seront demandées

lorsque vous contactez nos revendeurs ou services après-vente.

Caractéristiques produit

Cisaille SSH 6-A22

Génération : 01

N° de série :

*2253584*

2253584 Français 13

1.5 Déclaration de conformité

Nous déclarons sous notre seule et unique responsabilité que le produit décrit ici est conforme aux directives

et normes en vigueur. Une copie de l'attestation délivrée par l'organisme de certification se trouve en fin de

la présente documentation.

Pour obtenir les documentations techniques, s'adresser à :

Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916 Kaufering, DE

2 Sécurité

2.1 Indications générales de sécurité pour les appareils électriques

AVERTISSEMENT Lire toutes les consignes de sécurité et instructions, illustrations et caractéris-

tiques techniques, qui accompagnent cet outil électroportatif. Tout manquement à l'observation des

instructions suivantes risque de provoquer une électrocution, un incendie et/ou de graves blessures.

Les consignes de sécurité et instructions doivent être intégralement conservées pour les utilisations

futures.

La notion d'« outil électroportatif » mentionnée dans les consignes de sécurité se rapporte à des outils

électriques raccordés au secteur (avec câble d'alimentation) et à des outils électriques sur accu (sans câble

d'alimentation).

Sécurité sur le lieu de travail

▶ Conserver la zone de travail propre et bien éclairée. Un lieu de travail en désordre ou mal éclairé

augmente le risque d'accidents.

▶ Ne pas faire fonctionner les outils électriques en atmosphère explosive et où se trouvent des

liquides, des gaz ou poussières inflammables. Les outils électriques produisent des étincelles qui

peuvent enflammer les poussières ou les fumées.

▶ Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil électro-

portatif. En cas d'inattention il y a risque de perdre le contrôle de l'appareil.

Sécurité relative au système électrique

▶ La fiche de secteur de l'outil électroportatif doit être adaptée à la prise de courant. Ne jamais

modifier la fiche de quelque façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils

électriques à branchement de terre. Des fiches non modifiées et des prises de courant adaptées

réduiront le risque de choc électrique.

▶

Éviter le contact physique avec des surfaces mises à la terre tels que tuyaux, radiateurs, cuisinières

et réfrigérateurs. Il y a un risque élevé de choc électrique au cas où votre corps serait relié à la terre.

▶ Ne pas exposer les outils électroportatifs à la pluie ou à l'humidité. La pénétration d'eau à l'intérieur

d'un outil électroportatif augmentera le risque d'un choc électrique.

▶ Ne jamais utiliser le câble de raccordement à d'autres fins que celles prévues, telles que pour

porter, accrocher ou débrancher l'outil électroportatif de la prise de courant. Maintenir le câble

de raccordement à l'écart de la chaleur, des parties grasses, des bords tranchants ou des parties

en mouvement. Des câbles de raccordement endommagés ou emmêlés augmentent le risque de choc

électrique.

▶ Si l'outil électroportatif est utilisé à l'extérieur, utiliser uniquement des câbles de rallonge

homologués pour les applications extérieures. L’utilisation d’un câble de rallonge homologué

pour les applications extérieures réduit le risque d’un choc électrique.

▶ Si l'utilisation de l'outil électrique dans un environnement humide ne peut pas être évitée, utiliser

un interrupteur de protection contre les courants de court-circuit. L'utilisation d'un tel interrupteur

de protection réduit le risque d'une décharge électrique.

Sécurité des personnes

▶ Rester vigilant, surveiller ce que l'on fait. Faire preuve de bon sens en utilisant l'outil électroportatif.

Ne pas utiliser l'outil électroportatif en étant fatigué ou sous l'emprise de l'alcool, de drogues ou

de médicaments. Un moment d'inattention lors de l'utilisation de l'outil électroportatif peut entraîner

des blessures graves.

▶ Utiliser un équipement de protection personnel et toujours porter une protection pour les

yeux. Les équipements de protection personnels tels que masque antipoussière, chaussures de

sécurité antidérapantes, casque de protection ou protection acoustique suivant l'utilisation de l'outil

électroportatif, réduiront le risque de blessures des personnes.

▶

Éviter une mise en service par mégarde. S'assurer que l'outil électroportatif est arrêté avant de le

brancher à la source de courant et/ou à l'accu, de le prendre ou de le porter. Le fait de porter l'outil

14 Français 2253584

*2253584*

électroportatif avec le doigt sur l'interrupteur ou de brancher l'appareil sur la source de courant lorsque

l'interrupteur est en position de fonctionnement peut entraîner des accidents.

▶ Retirer tout outil de réglage ou toute clé avant de mettre l'outil électroportatif en fonctionnement.

Une clé ou un outil se trouvant sur une partie en rotation peut causer des blessures.

▶ Adopter une bonne posture. Veiller à toujours garder une position stable et équilibrée. Cela permet

un meilleur contrôle de l'outil électroportatif dans des situations inattendues.

▶ S'habiller de manière adaptée. Ne pas porter de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à distance des parties en mouvement. Des vêtements amples,

des bijoux ou des cheveux longs peuvent être happés par des parties en mouvement.

▶ Si des dispositifs servant à aspirer ou à recueillir les poussières doivent être utilisés, s'assurer

qu'ils sont effectivement raccordés et correctement utilisés. L'utilisation d'un dispositif d'aspiration

de la poussière peut réduire les risques dus aux poussières.

▶ Ne pas sous-estimer les mesures de sécurité à prendre et ne pas ignorer sciemment les règles

de sécurité applicables aux outils électriques, même si l'on est utilisateur chevronné après de

fréquentes utilisations de l'outil électroportatif. Un manque d'attention peut conduire à de graves

blessures en quelques fractions de seconde.

Utilisation et maniement de l'outil électroportatif

▶ Ne pas forcer l'appareil. Utiliser l'outil électroportatif adapté au travail à effectuer. Un outil

électroportatif approprié réalisera mieux le travail et de manière plus sûre au régime pour lequel il a été

conçu.

▶ Ne pas utiliser d'outil électroportatif dont l'interrupteur est défectueux. Tout outil électroportatif qui

ne peut plus être mis en ou hors fonctionnement est dangereux et doit être réparé.

▶ Débrancher la fiche de la prise de courant et/ou l'accu amovible avant d'effectuer des réglages sur

l'appareil, de changer les accessoires, ou de ranger l'appareil. Cette mesure de précaution empêche

une mise en fonctionnement par mégarde de l'outil électroportatif.

▶ Conserver les outils électroportatifs non utilisés hors de portée des enfants. Ne permettre

l'utilisation de l'appareil à aucune personne qui ne soit pas familiarisée avec celui-ci ou qui n'a

pas lu ces instructions. Les outils électroportatifs sont dangereux lorsqu'ils sont entre les mains de

personnes non initiées.

▶ Prendre soin des outils électroportatifs et des accessoires. Vérifier que les parties en mouvement

fonctionnent correctement et qu'elles ne sont pas coincées, et contrôler si des parties sont

cassées ou endommagées de sorte que le bon fonctionnement de l'outil électroportatif s'en trouve

entravé. Faire réparer les parties endommagées avant d'utiliser l'appareil. De nombreux accidents

sont dus à des outils électroportatifs mal entretenus.

▶ Garder les outils de coupe affûtés et propres. Des outils destinés à couper correctement entretenus

avec des arêtes de coupe tranchantes sont moins susceptibles de bloquer et sont plus faciles à contrôler.

▶ L'outil électroportatif, les accessoires, les outils amovibles, etc. doivent être utilisés conformément

à ces instructions. Tenir également compte des conditions de travail et du travail à réaliser.

L'utilisation des outils électroportatifs à d'autres fins que celles prévues peut entraîner des situations

dangereuses.

▶ Veiller à ce que les poignées et surfaces de préhension soient toujours être sèches, propres et

exemptes de traces de graisse ou d'huile. Avec des poignées et surfaces de préhension glissantes, la

sécurité et le contrôle de l'outil électroportatif ne peuvent être assurés dans des situations inopinées.

Utilisation et maniement de l'outil sur accu

▶ Ne charger les accus que dans des chargeurs recommandés par le fabricant. Si un chargeur

approprié à un type spécifique d'accus est utilisé avec des accus non recommandés pour celui-ci, il y a

risque d'incendie.

▶ Dans les outils électroportatifs, utiliser uniquement les accus spécialement prévus pour ceux-ci.

L'utilisation de tout autre accu peut entraîner des blessures et des risques d'incendie.

▶ Tenir l'accu non utilisé à l'écart de tous objets métalliques tels qu'agrafes, pièces de monnaie, clés,

clous, vis ou autres, étant donné qu'un pontage peut provoquer un court-circuit. Un court-circuit

entre les contacts d'accu peut provoquer des brûlures ou un incendie.

▶

En cas d'utilisation abusive, du liquide peut sortir de l'accu. Éviter tout contact avec ce liquide. En

cas de contact par mégarde, rincer soigneusement avec de l'eau. Au cas où le liquide rentrerait

dans les yeux, consulter en plus un médecin. Le liquide qui sort de l'accu peut entraîner des irritations

de la peau ou causer des brûlures.

▶ Ne pas utiliser d'accu endommagé ou modifié. Des accus endommagés ou modifiés peuvent avoir

un comportement imprévisible et provoquer un incendie, une explosion ou engendrer un risque de

blessures.

La page est en cours de chargement...

Hilti SSH 6-A22 Mode d'emploi

Marque: Hilti

Modèle: SSH 6-A22

Catégorie: Outils électroportatifs

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Hilti SSH 6-A22 User guide
español: Hilti SSH 6-A22 Guía del usuario
português: Hilti SSH 6-A22 Guia de usuario

Documents connexes

Autres documents

Trumpf C 250-0 PLUS Li Manuel utilisateur