Kenmore 14549 Guide d'installation

Installation Instructions

Instrucciones de instalación

Instructions d’installation

English / Español / Français

Kenmore®/Kenmore Elite®

Stainless Steel Tub

Undercounter Dishwasher

Lavavajillas empotrada con tina

de acero inoxidable

Lave-vaisselle encastré avec cuve

en acier inoxydable

P/N W10806907D

Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

www.sears.ca

2

TABLE OF CONTENTS

DISHWASHER SAFETY ...................................................... 3

INSTALLATION REQUIREMENTS ......................................4

Tools and Parts ..............................................................................4

Location Requirements ................................................................. 6

Product and Cabinet Opening Dimensions ............................... 7

Drain Requirements ....................................................................... 8

Water Supply Requirements ....................................................... 8

Electrical Requirements ................................................................ 8

INSTALLATION INSTRUCTIONS .......................................9

Prepare Cabinet Opening – NewUtilities ................................ 9

Install Optional Moisture Barrier ................................................ 9

Electrical Connection ................................................................. 10

Prepare Dishwasher ..................................................................... 11

Remove Access Panel .................................................................. 11

Connect Water Line to Fill Valve ..............................................12

Connect Fill Hose to Fill Valve ...................................................13

Drain Hose Connection ..............................................................13

Power Cord Connection ............................................................. 14

Install Door Handle......................................................................16

Place Dishwasher in Cabinet ......................................................16

Custom Panel Installation ........................................................... 17

Choose Anchor Attachment Method ....................................... 17

Final Installation Check ............................................................... 18

Secure Dishwasher inCabinetOpening ...................................19

Direct Wire Connection .............................................................20

Connect Water Line to House Shuto Valve .......................... 22

Connect Drain Hose ..................................................................22

Complete Installation .................................................................24

Install Access Panel .....................................................................25

Check Operation ........................................................................26

If Dishwasher Does Not Operate .............................................26

Additional Tips ............................................................................26

3

DISHWASHER SAFETY

You Need to:

■ Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials and

drainhose. Close dishwasher door until latched.

NOTE: Each dishwasher is tested at the factory and may

contain some residual water in the tub as a result of the test.

■ Observe all governing codes and ordinances.

■ Install this dishwasher as specied in these instructions.

■ Installation should be performed by a qualied

servicetechnician.

■ The dishwasher must be installed to meet all electrical

andplumbing national and local codes and ordinances.

Care shall be exercised when the appliance is installed

orremoved, to reduce the likelihood of damage to the

powercord.

WARNING: To reduce the risk of electric shock, re, or injury

to persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

4

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

anytools listed here.

All Installations

Tools Needed:

Pliers Flat-blade screwdriver

Phillips screwdriver Utility knife

5

/

16

" and

1

/

4

" nut drivers or

hex sockets

Small level

Measuring tape or ruler

5

/

8

" open-end wrench

10" adjustable wrench that

opens to 1

1

/

8

" (29 mm)

Torx

®†

T20

®

and, if installing

custom front panels, Torx

®

T15

®

screwdrivers

Other Useful Items You May Need:

Flashlight Shallow pan

Bath towel Masking or duct tape

Parts Supplied:

Drain hose clamps (2)

(1 large/red and 1 small/green)

Drain hose

#10 x

1

/

2

" Phillips-head

screws(2)

Undercounter mounting

brackets (2)

Make sure all these parts are included in the literature

package. If parts are not included, call us at our toll-free

number or visit our website listed in the User Guide.

Door handle (on some models)

†

®

TORX, T15, and T20 are registred trademarks of Acument Intellectual Properties, LLC.

5

Other Parts Needed (not provided):

3

/

8

" Compression x

3

/

4

"

Hose Fitting with rubber seal

and 90° elbow (required to

properly connect household

water line to the dishwasher)

(Part Number W10685193)

Household Wiring (Metallic)

Strain Relief to t

7

/

8

"

(22mm) hole (required to

properly secure household

wiring to the dishwasher

terminal box)

(Part Number 4396672)

NOTE: Use only UL Listed/

CSA Approved part.

Twist-On Wire Connectors

NOTES:

■ Conrm proper size for

connecting your gauge of

household wiring to the

16-gauge wiring in the

dishwasher.

■ Use only UL Listed/CSA

Approved parts.

Call us at our toll-free number, visit our website listed in the

User Guide for part numbers above, orsee local electrical/

plumbing supply retailer for equivalent.

Optional Accessory Parts Available:

Moisture Barrier Tape

NOTE: Moisture barrier tape

is an optional, added level

of protection if installing a

dishwasher under a wooden

countertop.

(Part Number 4396277)

Side Panel Kit

For enclosing the side of the

dishwasher when installing it

at the end of your cabinetry

(Part Number varies

with color.)

Call us at our toll-free number or visit our website listed in the

User Guide for part numbers above.

First-Time Installations

Check local codes. Check existing electrical supply. See

the “Electrical Requirements” section. It is recommended

that electrical connections be made by a licensed

electrical installer.

Additional Tools Needed:

Small tubing cutter Wire stripper

Cordless drill with

1

/

2

",

3

/

4

", and 1

1

/

2

" hole saw bits

Additional Parts Needed (not provided):

Copper Tubing (

3

/

8

" O.D.

suggested) or Flexible Braided

WaterSupply Line Kit (Part

Number W10278635RP).

Kitincludes braided hose

and

3

/

8

" compression x

3

/

4

"hosetting.

Screw-Type Clamps

1

/

2

"-2" (38-50 mm)

(3maximum)

Optional-Longer Drain Hose

Maximum length

12 ft (3.7 m)

(Part Number 3385556)

NOTE: Must meet AHAM/

IAPMO test standards, t

1" (25mm) drain connection,

and be resistant to heat

and detergent

Call us at our toll-free number, visit our website listed in the

Use and Care Guide for part numbers above, orsee local

plumbing supply retailer for equivalent.

NOTE: If using a exible braided hose, replace inlet hose

after 5years to reduce the risk of hose failure. Record

hoseinstallation or replacement dates on the hose for

futurereference.

6

For Direct Wire For Power Cord

Cabinet Grommet

For 1

1

/

2

" (38 mm) hole

in cabinet.

(PartNumber302797)

NOTE: Required for

metal cabine

ts

Power Cord Kit

Kit typically includes

power cord, metallic strain

relief,grommet, and twist-on

wi

re connectors.

(Part Number 4317824)

Call us at our toll-free number, visit our website listed in the

Use and Care Guide for part numbers above, orsee local

electrical supply retailer for equivalent.

LOCATION REQUIREMENTS

Dishwasher must be fully enclosed (top, sides, back, and oor)

upon installation. A side panel kit is available from your dealer

forinstalling your dishwasher at the end of your cabinetry.

An optional moisture barrier accessory is also available for

installing underneath a wooden countertop. See the “Tools

and Parts” section at the front of the guide for part details

andorders.

Check location where dishwasher will be installed. The location

must provide:

■ Convenient access for loading and unloading dishes. Corner

locations require a 2" (51 mm) minimum clearance between

the side of the dishwasher door and the wall or cabinet.

■ Easy access to water, electricity, and drain:

■ Grounded electrical supply is required.

■ This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■ Make sure pipes, wires, and drain hose are within the

shaded area shown in the “Product and Cabinet Opening

Dimensions” section.

■ Do not run drain lines, water lines or electrical wiring

where they can interfere with or contact dishwasher motor

or legs.

■ Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

NOTE: If dishwasher will be left unused for a period of

time or in a location where it may be subject to freezing,

have it winterized by authorized service personnel.

■ If installed in new construction, ush the water supply line

of debris before connecting it to the ll valve. If it is not

ushed, debris from the water supply could plug the ll

valve screen.

■ A square opening for proper operation and appearance

■ The cabinet front to be perpendicular to oor

■ A level oor

Helpful Hint: If oor at front of opening is not level with

oor at rear of opening, shims may be used to level

dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims

must be securely attached to the oor.

■ The location where the dishwasher will be installed must

provide clearance between motor and ooring. Motor

should not touch the oor.

■ Do not install dishwasher over carpeted ooring.

7

Product and Cabinet Opening Dimensions

23

7

/8"

(606 mm)

30"

(762 mm)

3

1

/2" - 4

1

/2"

(88 mm - 106 mm)

33

1

/2"

(851 mm)

min. with

wheels

removed

24

1

/2"

(622 mm)

B

3

/4"

(19 mm)

A

30"

(762 mm)

3

/4"

(94 mm)

21"

(533 mm)

C

24"

(620 mm)

E

24"

(620 mm)

34"

(864 mm)

D

3

"

(76 mm)

1

3

/4"

(44 mm)

6

3

/4"

(172 mm)

2

1

/4"

(64 mm)

2

1

/4"

(64 mm)

2

"

(51 mm)

6

1

/4"

(159 mm)

10

1

/2"

(267 mm)

4

"

(102 mm)

A. Insulation may be compressed (not used on all models).

B. For panel-ready models, dishwasher depth is 24" (610 mm),

not including the

3

/

4

" (19 mm) custom door panel.

C. Door handles may protrude forward of the face of the

dishwasher, varies by model.

For 4" (100 mm) toe kick, height of cabinet opening is

34

1

/

2

" (863 mm).

Check that all surfaces have no protrusions that would

prohibit dishwasher installation.

D. Measured from the lowest point on the underside of

the countertop. May be reduced to 33

1

/

2

" (851mm) by

removing the wheels and perforated area of insulation

(blanket) on dishwasher.

E. Minimum, measured from narrowest point of opening

NOTE: Shaded areas

of cabinet walls

show where utility

connections may

be installed.

8

■ Do not solder within 6" (152 mm) of the water inlet valve.

■ If installed in new construction, make sure the house

watersupply lines have been ushed prior to connecting

thedishwasher to remove any debris that may exist in

thesupply line.

NOTE: If replacing an existing dishwasher, it is recommended

to install a new water line (see the “Tools and Parts” section

at the front of the guide for part details) and drain hose

(supplied) with the new dishwasher.

ELECTRICAL REQUIREMENTS

Be sure that the electrical connection and wire size are

adequateand in conformance with the National Electrical

Code, ANSI/NFPA 70 - latest edition, and all local codes

andordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

You Must Have:

■ 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused

electricalsupply

■ Copper wire only

■ A maximum of 2 eld wiring supply conductors

(12AWGlargest size) plus 1 grounding conductor

arepermitted in the terminal box.

We Recommend:

■ A time-delay fuse or circuit breaker

■ A separate circuit

If Connecting Dishwasher with a Power Cord:

■ Use UL Listed power cord kit marked for

use with dishwasher. See the “Tools and

Parts” section at the front of the guide for part

details and orders.

■ Plug into a grounded 3prong outlet. Outlet must

meet all localcodes and ordinances.

If Connecting Dishwasher with Direct Wiring:

■ Use exible, armored, or nonmetallic

sheathed copper wire with grounding

wire that meets the wiring requirements

for your home and local codes and ordinances.

■ Use a UL Listed/CSA Approved metallic strain relief.

Seethe“Tools and Parts” section at the front of the

guideforpart details and orders.

DRAIN REQUIREMENTS

■ A new drain hose is supplied with your dishwasher.

Ifdrainhose is not long enough, use a new drain hose

witha maximum length of 12 ft (3.7 m) that meets all

currentAHAM/IAPMO test standards, is resistant to heat

and detergent, and ts the 1" (25 mm) drain connector of

thedishwasher. See the “Tools and Parts” section at the

front ofthe guide for part details and orders.

NOTE: Do not connect multiple drain hoses together.

■ Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (508

mm) minimum above the oor. It is recommended that the

drain hose either be looped up and securely fastened to the

underside of the counter or be connected to an air gap.

■ Make sure to use an air gap if the drain hose is connected

tohouse plumbing lower than 20" (508 mm) above

suboororoor.

■ If required, the air gap should be installed in accordance

withthe air gap installation instructions. When you are

connecting the air gap, a rubber hose (not provided) will

beneeded to connect to the waste tee or disposer inlet.

■ Use

1

/

2

" minimum I.D. drain line ttings.

WATER SUPPLY REQUIREMENTS

■ This dishwasher has a water heating feature and also

requires a connection to a hot water supply line.

■ A hot water line with 20 to 120 psi (138 to 862 kPa)

waterpressure can be veried by a licensed plumber.

■ 120°F (49°C) water at dishwasher

■

3

/

8

" O.D. copper tubing with compression tting or exible

braided water supply line. See the “Tools and Parts” section

atthe front of the guide for part details and orders.

NOTE:

1

/

2

" minimum plastic tubing is not recommended.

■ A 90° elbow with

3

/

4

" hose connection with rubber washer.

See the “Tools and Parts” section at the front of the guide

forpart details and orders.

Use of air gap

Air gap

9

PREPARE CABINET OPENING –

NEWUTILITIES

NOTE: Refer to the “Product and Cabinet Opening

Dimensions” section for the correct hole placement and

dimensions of the shaded area.

Drill a 1

1

/

2

" (38 mm) drain hose hole in the side or rear of

cabinet, depending on location of drain hose routing and

drain hose connection location.

Drill a

1

/

2

" (12.7 mm) water supply hose hole in the side or

rear of cabinet, depending on location of water supply

routing and connection location.

Drill a 1

1

/

2

" (38 mm) electrical conduit hole in the right-hand

side or rear of cabinet.

WARNING

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

1. Disconnect power

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

2. Shut o water supply

Shut o the water supply to the dishwasher.

3. Drill hole locations -

new construction

Preferred

location

Optional

location

1

/

2

"

(38mm)

1

/

2

"

(12.7mm)

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover edges of hole with grommet included

withpower cord kit. See the “Tools and Parts” section at

thefront of the guide forpart details.

Helpful Tip: Wiring the dishwasher will be easier if you route

thecable into the cabinet opening from the right-hand side.

INSTALL OPTIONAL MOISTURE BARRIER

RECOMMENDED FOR WOOD COUNTERTOPS

See the “Tools and Parts” section at the front of the guide for

part details and orders. Make sure the area under the cabinet

is clean and dry for installation of the moisture barrier. Remove

the backing of the moisture barrier, and apply to underside of

thecountertop along the front edge of the counter.

NOTE: Install wood shims if side anchoring and the gap

between the sides of the cabinet and sides of the dishwasher

are greater than

1

/

2

" (12.7 mm) on each side or are greater

than the length of the side anchor screws.

4. Sand holes smooth

Metal

cabinet

Wood

cabinet

Moisture barrier/wood shims

Moisture

barrier

Install

wood

shims

INSTALLATION INSTRUCTIONS

10

Built-up oors: If the kitchen oor is higher than the cabinet

opening’s oor - for example, the kitchen oor tile does not

extend into the cabinet opening - add shims, as needed, in

the area shown to bring the dishwasher up to 34" (864 mm)

below the countertop.

NOTE: Shims must be securely attached to oor to avoid

movement when the dishwasher is in use.

Remove and discard the foam blocks (if blocks are present;

notall models have them) located above the front legs on

eachside of the dishwasher. The blocks cover the rope/link

pulleys on the dishwasher.

5. Built-up oors – addshimsasneeded

6. Remove foam block

Foam block

Cut insulation blanket along perforation for cabinet opening

height of 33

1

/

2

" (851 mm). For other cabinet opening heights,

donot cut the insulation blanket.

ELECTRICAL CONNECTION

– For Direct Wire, begin with Step 7

– For Power Cord, wait until Step 22

If installing with direct wire, route the cable as shown.

Route cable from power supply through cabinet hole. (Cable

must extend to the right front side of cabinet opening.) Tape

cable to the oor in area shown. This will prohibit cable from

moving when dishwasher is moved into cabinet opening.

NOTE: If removing a previous dishwasher with a power cord,

you will need to transfer the power cord to the new dishwasher.

If installing into a

33

1

/

2

" (851mm)opening

7. Direct wire – route cable

11

PREPARE DISHWASHER

Helpful Tip: Place cardboard under dishwasher until installed

incabinet opening to avoid damaging oor covering.

Using 2 or more people, grasp sides of dishwasher door

frame,and place the dishwasher on its back.

Do not use the door panel as a worktable without rst

coveringitwith a towel to avoid scratching the door panel.

NOTE: On some models, once the dishwasher is on its back,

pull on the door handle to remove it from the access panel.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

8. Put dishwasher on its back

REMOVE ACCESS PANEL

– For Plastic Access Panels, go to Step 9

– For Metal Access Panels, go to Step 10

Using a at-blade screwdriver, turn the plastic fasteners

1

/

4

turn counterclockwise to unlock them. Remove panel. Do not

remove tech sheet from access panel. Go to Step 11.

Using a

1

/

4

" nut driver or Phillips screwdriver, remove 2 screws

attaching access panel to dishwasher. Do not remove tech

sheet from access panel.

9. Plastic panel

1

/

4

turn

10. Metal panel

12

Measure height of cabinet opening from underside of

countertop to oor where dishwasher will be installed.

Be sure to measure the lowest point on the underside

of the countertop and the highest point on the oor.

Adjust both front leveling legs to the same height. Put the rear

wheels in the correct position according to the “Dishwasher

Height Adjustment Chart.”

NOTE: If the minimum cabinet opening height is less

than 34" (864 mm), the rear wheels can be removed for

additionalclearance.

This will allow the dishwasher to t into a 33

1

/

2

" (851 mm)

highcabinet opening, but the dishwasher will be more

diculttomove. Measurements are approximate.

11. Measure cabinet opening

Dishwasher Height Adjustment Chart

Cabinet opening

height

Front legs

height

Wheel

position

Insulation

blanket

33

1

/

2

" (851 mm)

3

/

8

" (9.8 mm) Removed Cut

34" (864 mm)

9

/

16

" (14 mm) 1 No Cut

34

1

/

4

" (871 mm)

13

/

16

" (21 mm) 2 No Cut

34

1

/

2

" (876 mm)

11

/

16

" (27 mm) 3 No Cut

Front legs – A

Refer to the “Dishwasher Height Adjustment Chart” for wheel

position and for height of front legs needed for your cabinet

opening height.

Remove and discard the plastic rail cover on each side of

thedishwasher frame. To remove the plastic rail cover, push

upward and back to unsnap it from the dishwasher frame.

CONNECT WATER LINE TO FILL VALVE

– For Copper line, begin with Step 14

– For Flexible line, begin with Step 16

If using copper tubing, measure overall length of copper

tubing required to reach the water supply, cut to length,

and attach with compression ttings.

12. Adjust wheels and legs

13. Remove plastic rail cover

(only on certain models)

Plastic

rail cover

14. Copper water line

13

Copper tubing only: Put the tubing into the 90° elbow tting

as far as it will go. (The copper tubing bends and kinks easily.)

Slide the nut and ferrule forward and start the nut onto the

elbowthreads.

NOTE: To avoid vibration during operation, route the water

supply line so that it does not touch the dishwasher base,

frame,or motor. Go to Step 17.

Flexible braided line: Conrm the exible braided line is long

enough. See the “Tools and Parts” section at the front of the

guide for part details and orders.

Get

3

/

8

" compression x

3

/

4

" hose tting with 90° elbow. See

the “Tools and Parts” section at the front of the guide for part

details and orders. Connect the

3

/

8

" compression tting of the

90° elbow tting to the water supply line. Attach such that the

3

/

4

" connection is facing upward as shown above.

15. Slide nut and ferrule onto tubing

(copper tubing only)

Nut

Ferrule

16. Flexible line

17. Add 90° elbow tting to the

watersupply line

CONNECT FILL HOSE TO FILL VALVE

Be sure rubber washer is properly seated in tting. Slide the

3

/

4

" tting of the 90° elbow up to the valve and hand tighten

to avoid cross-threading. Hand tighten until the coupling is

tight. Using pliers, check the tightness of the coupling. An

additional

1

/

4

to

1

/

2

turn may be required to seal the rubber

gasket. Route ll hose out the rear left side of unit.

NOTES:

■ Do not use Teon

®†

tape with compression ttings.

■ Do not over-tighten. Damage to the coupling can result.

DRAIN HOSE CONNECTION

Place towel under drain hose to catch any water in drain hose.

Place the small (green) drain hose clamp onto the small end

ofthe drain hose. Push the new drain hose into the rubber

drainhose connector up to the drain hose stop.

Using pliers, squeeze open the small drain hose clamp and

slide it onto the connector between stops.

†

®

TEFLON is a registered trademark of Chemours.

18. Tighten 90° elbow tting to valve

19. Connect drain hose

Stop

Drain hose

stop

Drain

hose

Rubber drain

hose connector

Small clamp

20. Slide clamp onto connector

Stop

Drain hose stop

Drain hose

Rubber drain

hose connector

Small clamp

14

NOTE: Route drain hose out the rear of the dishwasher.

POWER CORD CONNECTION

NOTE: If removing a previous dishwasher with a power cord,

you will need to transfer the power cord to the new dishwasher.

Use a

1

/

4

" nut driver or

1

/

4

" hex head socket wrench to remove

the screw that holds the terminal box to the cross brace. Then,

tilt the terminal box, free the tab, and lift the terminal box

away from the crossbar.

Remove the cover by sliding it up and lifting its hooks out

oftheslot. Retain cover for later use.

21. Hose clamp nal position

Stop

Drain hose stop

Drain hose

Rubber drain

hose connector

Small clamp

22. Remove terminal box

23. Remove cover

Install a UL Listed/CSA Approved metallic strain relief. Make

sure screw heads are facing up when tightening conduit

nut. Strain relief is provided with the power cord kit. See the

“Toolsand Parts” section at the front of the guide for part

detailsand orders.

Route cord so that it does not touch dishwasher motor or

lowerpart of dishwasher tub. Pull cord through strain relief

interminal box.

NOTE: A maximum of 2 power cord supply conductors

(12AWG largest size) plus 1 grounding conductor are

permitted in the terminal box.

24. Install strain relief

25. Power cord – route cord

intoterminal box

15

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Replace the cover by

inserting the hooks of the terminal cover into the slots in

the oor of the terminal box and sliding the cover tight

against the back wall where wires come in. Make sure

wires are tucked inside the box and not pinched by

the cover.

Put the terminal box back on the crossbar with the tab

in place. Use a

1

/

4

" nut driver and the screw removed in

Step 22 to secure the terminal box to the crossbar.

Once the terminal box has been remounted on the

dishwasher, tuck any excess length or slack over nearby

components or clip them back into the nearby clips to

help keep them o the oor.

NOTE: Route power cord out the rear of the dishwasher.

Do not plug cord into an outlet until instructed to do so.

Wiring conguration

28. Power cord – secure cord

onstrainrelief

29. Power cord – reinstall terminal

boxcover and wires

Remove the ground connector screw on the raised oor inside

the box and place it through the ring terminal of the green

ground wire of power cord. Reattach and tighten the ground

connector screw to the raised oor of the box.

Select UL Listed/CSA Approved twist-on wire connectors of

the proper size. See the “Tools and Parts” section at the front

of the guide for part details. Connect wires, black to black

and white to white, using the twist-on wire connectors.

NOTE: Do not pre-twist stranded wire. Twist on wire

connector. Gently tug on wires to be sure both are secured.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

26. Power cord – connect ground wire

Ground

wire

Ground

wire

Ground screw

Washer

27. Power cord – connect

remainingwires

16

IMPORTANT: If wheels were removed, cover the oor when

moving the dishwasher. Slowly move dishwasher completely

into cabinet opening. Do not kink or pinch water line, drain

hose, power cord, or direct wire between dishwasher and

cabinet. Remove cardboard from under dishwasher.

It is all right if dishwasher ts tightly into cabinet opening.

Do not remove insulation blanket – the blanket reduces the

sound level.

NOTE: Route water supply, drain hose, and power cord out

the rear of the dishwasher.

Route the utilities through the holes in the cabinet, and pull

theslack out at the same time as the dishwasher is pushed

intothe cabinet.

If using a power cord, make sure to route end through hole

in cutout before sliding dishwasher into cabinet opening.

NOTE: Make sure insulation blanket is secured at both left

and right rear corners before pushing into cabinet opening to

keep the blanket from bunching up in a tight tting cabinet.

32. Move dishwasher close

tocabinetopening

Water

line

Drain

hose

Cable

33. Route power cord

34. Secure insulation blanket

Insulation

blanket

Secure

blanket

INSTALL DOOR HANDLE

(ON SOME MODELS)

IMPORTANT: Do not scratch the front panel during this

procedure. If door panel has a protective lm, peel lm back

pastthe point of the handle studs before installing handle.

Handle iseasiest to install while unit is on its back.

Remove the door handle and hex key from the packaging.

Setscrews are already installed in the handle. Place handle

onmounting studs with the setscrews facing down. Push

thedoor handle tightly against the door. Insert the short

end ofthehex key into the setscrews. Tighten the setscrews

1

/

4

turnpast snug.

Retain hex key with Installation Instructions.

PLACE DISHWASHER IN CABINET

Using 2 or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

30. Install door handle

Handle

Mounting stud

Setscrew

(in bottom

of handle)

Hex key

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

31. Stand dishwasher upright

17

Countertop Attachment:

Remove the brackets from the package, and insert into the

openslots on the left- and right-hand top of the dishwasher

collaras shown. Go to Step 41.

Using pliers, bend/twist tab to lock the brackets in place.

Side Attachment:

Break o the end of the bracket along the scored line

usingpliers.

37. Insert bracket

Tabs must point

to the right.

Bend tab

38. Break end of bracket

Score line

NOTE: Leave unit about 6" (152 mm) out from cabinet in

order to install anchor brackets and adjust door tension

if needed.

NOTE: Pull slack out of utilities at the same time the

dishwasher is pushed into the cabinet opening to avoid

any kinks.

CUSTOM PANEL INSTALLATION

(CUSTOM PANEL MODELS ONLY)

For custom panel installation, refer to the Custom Panel

Installation Instruction Sheet (Part Number W10750117A).

Complete custom panel installation before proceeding to

the“Choose Anchor Attachment Method” section.

CHOOSE ANCHOR ATTACHMENT METHOD

IMPORTANT: The dishwasher must be secured to the

cabinet as one of the nal steps. Prepare the dishwasher for

this by attaching the 2 brackets found in the parts bag to

thedishwasher.

– For countertops that are wood, laminate or another

similar surface, use Countertop Attachment: go to

Step 37.

– For countertops that are marble, granite, or another

hard surface, use Side Attachment: go to Step 38.

NOTE: If the gap between the top of the door and the

underside of the counter top is tight (less than

1

/

4

" [6.35 mm]),

we suggest using Side Attachment to keep from scratching

the User Interface or console with the anchor screws.

35. Move dishwasher all but 6"

(152mm) intocabinet opening

6"

(152 mm)

36. Pull slack from utilities

18

If door closes too quickly or falls, open and adjust

spring tension.

To adjust the door spring tension, remove the white plastic

rope end attached to the door hinge. Using a

5

/

16

" nut

driver or hex socket, remove the screw from the tensioner.

The screw can be put into one of 3 holes (1, 2, 3) in the

front leg of the dishwasher.

If the door closes by itself: Move the tensioner to a lower-

numbered hole and replace the screw. Reattach the white

plastic rope end to the door hinge.

If the door opens by itself: Move the tensioner to a higher

numbered hole and replace the screw. Reattach the white

plastic rope end to the door hinge.

NOTE: Tensioners on both sides of dishwasher should be

secured at same holes.

Align front of dishwasher door panel with front of cabinet

doors. You may need to adjust alignment to be even with

your cabinets.

42. Door spring tension adjustment

Spring

3

2

1

Plastic

rope end

Tensioner

Screw

43. Align front of dishwasher

withfrontof cabinet doors

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher

is installed.

Push bracket into slot on the side of dishwasher, and bend

tab in toward the side of the dishwasher so that it keeps

the bracket in place. Repeat this step for the other side of

the dishwasher.

NOTE: Install wood shims to the inside of the cabinets if the

gap between the sides of the cabinet and the sides of the

dishwasher are greater than

1

/

2

" (13 mm) on each side.

NOTE: Do not attach the dishwasher. This will be done later.

FINAL INSTALLATION CHECK

39. Remove plastic buttons

Plastic

button

40. Install bracket

Bend

tabs

41. Open and close door

19

SECURE DISHWASHER

INCABINETOPENING

Check that dishwasher is still level front to back and side to

side in cabinet opening.

Open dishwasher door and place towel over pump assembly

and spray arm of dishwasher. This will keep screws from

falling into pump area when you are securing dishwasher

to cabinet.

Open dishwasher door to prepare for securing the dishwasher

tothe countertop or side cabinet.

NOTES:

■ The dishwasher must be secured to keep it from shifting

whenthe door is opened or closed.

■ Do not drop screws into bottom of dishwasher.

■ Locate brackets installed in the “Choose Anchor

Attachment Method” section, either on top or on the

sidesofthe dishwasher.

■ If countertop anchoring: Secure dishwasher to

the countertop with two #10 x

1

/

2

" Phillips-head

screws(included).

■ If side anchoring: Drill pilot holes in cabinet to avoid

splittingthe wood. Secure dishwasher to cabinet with two

#10x

1

/

2

" Phillips-head screws (included). Remove upper

rack for easier access. See the Use and Care Guide for

instructions how to remove the upper rack if needed.

46. Double-check dishwasher

alignment in cabinet opening

47. Secure dishwasher

Screw to side

cabinet

Check that leveling legs are rmly against the oor. Close

and latch the door and place level against the front panel.

Check that dishwasher is centered from front to back in the

opening. Ifneeded, adjust leveling leg until dishwasher is

plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise

dishwasher o the ground to adjust front legs. With some

installations, it may be easier to adjust the front leg using

a

3

/

16

" hex head socket or adjustable wrench. If the gap

between the top of the door and the underside of the

counter top is tight (less than

1

/

4

" [6 mm]), we suggest

side anchoring to keep from scratching the User Interface

or console.

Place level against top front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not

level,adjust front legs up or down until dishwasher is level.

44. Check for plumb and adjust legs

ifneeded

Level legs

Optional

method

Preferred

method

45. Check level side to side and adjust

legs if needed

20

DIRECT WIRE CONNECTION

Use a

1

/

4

" nut driver or

1

/

4

" hex head socket wrench to remove

the screw that holds the terminal box to the cross brace. Then,

tilt the terminal box, free the tab, and lift the terminal box

away from the crossbar.

Remove the cover by sliding it up and lifting its hooks out of

the slots. Retain cover for later use.

There should be adequate length in the wires to pull the

terminalbox out from under the dishwasher. Lift the wires

oofthe nearby clips or components to extend the length

ofwire harness for easier access.

51. Remove terminal box

52. Remove cover

53. Unclip green, white,

and black wires

IMPORTANT: Check that top of door does not contact screws,

brackets, or countertop. If it does, adjust leveling legs or use

the side attachment option.

Open door and check that space between dishwasher cabinet

opening and tub is equal on both sides. If spacing is not equal,

loosen bracket screws and shift tub. Tighten bracket screws.

If side attachment method was used, reinstall the gray

plastic buttons removed in Step 39 to hide the screw holes.

48. Check door clearance

49. Check inner spacing

50. Reinstall plastic buttons

Plastic button

La page charge ...

Kenmore 14549 Guide d'installation

Kenmore 14549 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents