GE 490000 Le manuel du propriétaire

Marque: GE

Modèle: 490000

Catégorie: Accessoires pour véhicules automobiles

Taper: Le manuel du propriétaire

Ce manuel convient également à

490000 Vanguard Gaseous

English

es fr

Español Français

Operator’s Manual

Manual del Operario

Manuel de l’opérateur

Form No. 279144TRI

Revision: A

E 2011 Briggs & Stratton Corporation,

Briggs & Stratton is a registered trademark

of Briggs & Stratton Corporation

Model 490000 Professional Seriest

Gaseous

Not for

Reproduction

BRIGGSandSTRATTON.COM

Not for

Reproduction

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

General Information

This manual contains safety information to make you aware of the hazards and risks

associated with engines and how to avoid them. It also contains instructions for the

proper use and care of the engine. Because Briggs & Stratton Corporation does not

necessarily know what equipment this engine will power, it is important that you read and

understand these instructions and the instructions for the equipment. Save these

original instructions for future reference.

For replacement parts or technical assistance, record below the engine model, type, and

code numbers along with the date of purchase. These numbers are located on your

engine (see the Features and Controls page).

Date of purchase:

Engine model:

MM/DD/YYYY

Model: Code:Type:

Power Rating

The gross power rating for individual gas engine models is labeled in accordance with

SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque

Rating Procedure), and rating performance has been obtained and corrected in

accordance with SAE J1995 (Revision 2002--05). Torque values are derived at 3060

RPM; horsepower values are derived at 3600 RPM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine--to--engine

variability. Given the wide array of products on which engines are placed, the gas engine

may not develop the rated gross power when used in a given piece of power equipment.

This difference is due to a variety of factors including, but not limited to, the variety of

engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.),

application limitations, ambient operating conditions (temperature, humidity, altitude), and

engine--to--engine variability.

Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an

engine of higher rated power for this Series engine.

Operator Safety

Explosion

Toxic Fumes

Moving Parts

Shock

Hot Surface

Kickback

Fire

Fuel Shutoff

Read Manual

Choke

Oil

Fuel

On Off

Wear Eye

Protection

Slow

Fast

SAFETY AND CONTROL SYMBOLS

Hazardous

Chemical

Frostbite

Stop

The safety alert symbol is used to identify safety information about hazards that can

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used with the

alert symbol to indicate the likelihood and the potential severity of injury . In addition, a hazard

symbol may be used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or

moderate injury.

NOTICE indicates a situation that could result in damage to the product.

WARNING

Certain components in this product and its related accessories contain

chemicals known to the State of California to cause cancer, birth defects, or

other reproductive harm. Wash hands after handling.

WARNING

The engine exhaust f rom this product contains chemicals known to the

State of California to cause cancer, birth defects, or other reproductive

harm.

WARNING

Briggs & Stratton does not approve or authorize the use of these engines

on 3-wheel All Terrain Vehicles (ATVs), motor bikes, fun/recreational

go-karts, aircraft products, or vehicles intended for use in competitive

events. Use of these engines in such applications could result in property

damage, serious injury (including paralysis), or even death.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

 Fill fuel tank outdoors or in well-ventilated area.

 Check fuel lines, tank, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

When Starting Engine

 Ensure that spark plug, muffler, and air cleaner (if equipped) are in place and

secured.

 Do not crank engine with spark plug removed.

When Operating Equipment

 Never start or run the engine with the air cleaner assembly (if equipped) or the

air filter (if equipped) removed.

When Transporting Equipment

 On Natural/Liquid Petroleum (LP) Gas engines, transport with fuel cylinder

empty or valve closed, or fuel tank disconnected.

When Storing Fuel Or Equipment With Fuel In Tank

 Store away from furnaces, stoves, water heaters or other appliances that have

pilot lights or other ignition sources because they can ignite fuel vapors.

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

WARNING

 If there is natural or LP gas leakage in area, do not start engine.

 Do not use pressurized starting fluids because vapors are flammable.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

 Start and run engine outdoors.

 Do not start or run engine in enclosed area, even if doors or windows are open.

Not for

Reproduction

Rapid r etraction of starter cord (kickback) will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

WARNING

 When starting engine, pull the starter cord slowly until resistance is felt and then

pull rapidly t o avoid kickback.

 Remove all external equipment/engine loads before starting engine.

 Direct-coupled equipment components such as, but not limited to, blades,

impellers, pulleys, sprockets, etc., must be securely attached.

Rotating parts can contact or entangle hands, feet, hair, clothing, or

accessories.

Traumatic amputation or severe laceration can result.

WARNING

 Operate equipment with guards in place.

 Keep hands and feet away from rotating parts.

 Tie up long hair and remove jewelry.

 Do not wear loose-fitting clothing, dangling drawstrings or items that could

become caught.

Running engines produce heat. Engine parts, especially muffler,

become extremely hot.

Severe thermal burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

WARNING

 Allow muffler, engine cylinder and fins to cool before touching.

 Remove accumulated debris from muffler area and cylinder area.

 It is a violation of California Public Resource Code, Section 4442, to use or

operate the engine on any forest-covered, brush-covered, or grass-covered land

unless the exhaust system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only c orrect tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

WARNING

Gaseous fuels are extremely flammable and readily form explosive

air-vapor mixtures at ambient temperatures.

 Do not start the engine.

 Do not actuate any electrical switches.

 Do not use a phone in the vicinity.

 Evacuate the area.

 Contact the gas supplier or fire department.

 Installation, adjustment and repair work should be done by a qualified

technician.

 Regularly check flexible supply line. Make sure they are in good condition.

Replace damaged or leaking components.

WARNING

Wear eye protection when doing repair work.

Frostbite can result from skin/eye contact with leaking LP liquid.

WARNING

Missing or inoperative “fuel lock-off” valve can cause a fire or

explosion.

 Do not operate the equipment if the “fuel lock-off” valve is missing or inoperative.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

Features and Controls

Compare the illustration

with your engine to familiarize yourself with the location of

various features and controls.

A. Engine Identification

Model Type Code

B. Spark Plug

C. Air Cleaner

D. Dipstick

E. Oil Drain Plug

F. Finger Guard

G. Oil Filter

H. Electric Starter

I. Quick Oil Drain (optional)

J. Oil Cooler

Operation

Oil capacity (see the Specifications section)

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty Certified oils for best

performance. Other high-quality detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for the engine. Use the chart to

select the best viscosity for the outdoor temperature range expected.

SAE 30

10W-30

Synthetic 5W-30

5W-30

°F °C

* Below 40°F(4°C) the use of SAE 30 will result in hard starting.

** Above 80°F(27°C) the use of 10W-30 may cause increased oil consumption. Check

oil level more frequently.

How To Check/Add Oil - Figure

Before adding or checking the oil

 Place engine level.

 Clean the oil fill area of any debris.

1. Remove the dipstick (A) and wipe with a clean cloth (Figure 2).

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be at the FULL mark (B)onthe

dipstick.

4. If low, add oil slowly into the engine oil f ill (C). Do not overfill. After adding oil, wait

one minute and then recheck the oil level.

Note: Do not add oil at the quick oil drain ( L, Figure 1) (if equipped).

5. Replace and tighten the dipstick.

Oil Pressure

If the oil pressure is too low, a pressure switch (if equipped) will either stop the engine or

activate a warning device on the equipment. If this occurs, stop the engine and check the

oil level with the dipstick.

If the oil level is below the ADD mark, add oil until it reaches the FULL mark. Start the

engine and check for proper pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not start the engine. Contact an

Authorized Briggs & Stratton Dealer to have the oil pressure problem corrected.

Fuel Recommendations

WARNING

Missing or inoperative “fuel lock-off” valve can cause a fire or

explosion.

 Do not operate the equipment if the “fuel lock-off” valve is missing or inoperative.

Fuel must meet these requirements:

 Use clean, dry fuel, free of moisture or any particulate material. Using fuels outside

the following recommended values may c ause performance problems.

 In engines set up to run on LPG, commercial grade HD5 LPG is recommended.

Recommended fuel composition is fuel with a minimum fuel energy of 2500 BTU’s/ft

with maximum propylene content of 5% and butane and heavier gas content of 2.5%

and minimum propane content of 90%.

NG or LPG engines are certified to operate on natural or liquid propane gas. The

emissions control system for this engine is EM (Engine Modifications).

How To Add Fuel

For information on refueling natural or LP gas engines, read the operating instructions

supplied by the equipment manufacturer.

How To Start The Engine

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

 Ensure that spark plug, muffler, and air cleaner (if equipped) are in place and

secured.

 Do not crank engine with spark plug removed.

Engines give off carbon monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause nausea, fainting or death.

WARNING

 Start and run engine outdoors.

 Do not start or run engine in enclosed area, even if doors or windows are open.

NOTICE: This engine was shipped from Briggs & Stratton without oil. Before you start

the engine, make sure you add oil according to the instructions in this manual. If you

start the engine without oil, it will be damaged beyond repair and will not be covered

under warranty.

1. Check the oil level. See the How To Check/Add Oil section.

2. See the equipment manual for starting procedure.

How To Stop The Engine

See the equipment manual for stopping procedure.

Not for

Reproduction

Maintenance

We recommend that you see any Briggs & Stratton Authorized Dealer for all

maintenance and service of the engine and engine parts.

NOTICE: All the components used to build this engine must remain in place for proper

operation.

Emissions Control

Maintenance, replacement, or repair of the emissions control devices and systems

may be performed by any non-road engine repair establishment or individual.

However, to obtain “no charge” emissions control service, the work must be performed

by a factory authorized dealer. See the Emissions Warranty.

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement, traumatic

amputation, or laceration.

Fire hazard

WARNING

Before performing adjustments or repairs:

 Disconnect the spark plug wire and keep it away from the spark plug.

 Disconnect battery at negative terminal (only engines with electric start.)

 Use only c orrect tools.

 Do not tamper with governor spring, links or other parts to increase engine

speed.

 Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts may not perform as well, may damage

the unit, and may result in injury.

 Do not strike the flywheel with a hammer or hard object because the flywheel

may later shatter during operation.

When testing for spark:

 Use approved spark plug tester.

 Do not check for spark with spark plug removed.

Maintenance Chart

First 5 Hours

 Change oil

Every8HoursorDaily

 Check engine oil level

Every 50 Hours or Annually

 Clean air filter *

 Change engine oil

 Replace oil filter (if equipped)

 Check muffler and spark arrester (if equipped)

Every 100 Hours or Annually

 Replace air filter

 Replace spark plugs

 Clean air cooling system *

 Check valve clearance. Adjust if necessary.

Annually

 Replace air filter

 Replace spark plugs

 Clean air cooling system *

* In dusty conditions or when airborne debris is present, clean more often.

How To Replace The Spark Plug - Figure

Check the gap (A, Figure 3) with a wire gauge (B). If necessary, reset the gap. Install

and tighten the spark plug to the recommended torque. For gap setting or torque, see the

Specifications section.

Note: In some areas, local law requires using a resistor spark plug to suppress ignition

signals. If this engine was originally equipped with a resistor spark plug, use the same

type for replacement.

Inspect Muffler And Spark Arrester