Generac 16 kW G0062573 Manuel utilisateur

Owner’s Manual

60 Hz Air-Cooled Generators

8 kW to 22 kW

SAVE THIS MANUAL FOR FUTURE REFERENCE

Para español , visita: http://www.generac.com/service-support/product-support-lookup

Pour le français, visiter : http://www.generac.com/service-support/product-support-lookup

000918

Register your Generac product at:

WWW.GENERAC.COM

1-888-GENERAC

(888-436-3722)

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

ii Owner’s Manual for 60 Hz Air-cooled Generators

Use this page to record important information about your generator set.

Record the information found on your unit data label on this

page. For the location of the unit data label, see General

Information. The unit has a label plate affixed to the inside

partition, to the left of the control panel c

onsole as shown in

Figure 2-1 and Figure 2-2. For directions on how to open

the top lid and remove the front panel, see Operation.

When contacting an Independent Authorized Service Dealer

about parts and service, always supply the complete model

number and serial number of the unit.

Operation and Maintenance: Proper maintenance and care

of the generator ensures a minimum number of problems

and keeps operating expenses at a minimum. It is the

operator’s responsibility to perform all safety checks, to

make sure that all maintenance for safe operation is

performed promptly, and to have the equipment checked

periodically by an Independent Authorized Service Dealer.

Normal maintenance, service and replacement of parts are

the responsibility of the owner/operator and, as such, are not

considered defects in materials or workmanship within the

terms of the warranty. Individual operating habits and usage

may contribute to the need for additional maintenance or

service.

When the generator requires servicing or repairs, Generac

recommends contacting an Independent Authorized Service

Dealer for assistance. Authorized service technicians are

factory-trained and are capable of handling all service

needs.To locate the nearest Independent Authorized Service

Dealer, please visit the dealer locator at:

www.generac.com/Service/DealerLocator/.

Model:

Serial:

Prod Date Week:

Volts:

LPV Amps:

NG Amps:

Hz:

Phase:

Controller P/N:

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000004)

WARNING

California Proposition 65. Engine exhaust and some

of its constituents are known to the state of California

to cause cancer, birth defects, and other reproductive

harm.

Table of Contents

Owner’s Manual for 60 Hz Air-Cooled Generators iii

Section 1: Safety Rules & General

Information

Introduction ..........................................................1

Read This Manual Thoroughly ....................................1

How to Obtain Service .................................................1

Safety Rules .........................................................1

General Hazards .........................................................2

Exhaust Hazards .........................................................3

Electrical Hazards .......................................................3

Fire Hazards ................................................................4

Explosion Hazards ......................................................4

Section 2: General Information

The Generator ......................................................5

Generator ....................................................................6

Protection Systems .............................................7

Emission Information ..........................................7

Fuel Requirements ..............................................7

Battery Requirements .........................................7

Battery Charger ....................................................7

Engine Oil Requirements ....................................7

Section 3: Operation

Site Prep Verification ...........................................9

Side Compartment ...............................................9

Main Circuit Breaker (Generator Disconnect) ..............9

LED Indicator Lights ....................................................9

120V GFCI Outlet/15 Amp Breaker

(16-22 kW Only) ..........................................................9

Generator Enclosure ...........................................9

Control Panel Interface .....................................11

Setting the Exercise Timer ................................14

Battery Charger ..................................................14

Manual Transfer Operation ...............................14

Transfer to Generator Power Source ........................15

Transfer Back to Utility Power Source .......................15

Automatic Transfer Operation ......................... 16

Automatic Sequence of Operation .................. 16

Utility Failure ..............................................................16

Cranking ....................................................................16

Cold Smart Start ........................................................16

Load Transfer ............................................................16

Shutting Generator Down While Under Load . 16

To turn the generator OFF: .......................................16

To turn the generator back ON: .................................16

Section 4: Maintenance

Maintenance ....................................................... 17

Performing Scheduled Maintenance ............... 17

Service Schedule ............................................... 17

Checking Engine Oil Level ............................... 18

Engine Oil Recommendations ...................................18

Changing the Oil and Oil Filter ......................... 19

Changing the Engine Air Cleaner .................... 19

Spark Plugs ........................................................ 19

Valve Clearance Adjustment ............................ 20

Check Valve Clearance .............................................20

Adjust Valve Clearance .............................................20

Battery Maintenance ......................................... 20

Attention After Submersion ............................. 21

Corrosion Protection ........................................ 21

Remove From/ To Service Procedure ............. 22

Remove From Service ...............................................22

Return to Service .......................................................22

Section 5: Troubleshooting

Section 6: Quick Reference Guide

Table of Contents

iv Owner’s Manual for 60 Hz Air-Cooled Generators

This page intentionally left blank.

Section 1: Safety Rules & General Information

Owner’s Manual for 60 Hz Air-cooled Generators 1

Section 1: Safety Rules & General Information

Introduction

Thank you for purchasing this compact, high

performance, air-cooled, engine-driven generator. It is

designed to automatically supply electrical power to

operate critical loads during a utility power failure.

This unit is factory installed in an all-weather, metal

enclosure that is intended exclusively for outdoor

installation. This generator will operate using either vapor

withdrawn liquid propane (LP) or natural gas (NG).

NOTE: When sized properly, this generator is suitable for

supplying typical residential loads such as induction

motors (sump pumps, refrigerators, air conditioners,

furnaces, etc.), electronic components (computer,

monitor, TV, etc.), lighting loads and microwaves.

Read This Manual Thoroughly

If any portion of this manual is not understood, contact

the nearest Independent Authorized Service Dealer for

starting, operating and servicing procedures.

This manual must be used in conjunction with the

appropriate Owner’s Manual.

SAVE THESE INSTRUCTIONS: The manufacturer

suggests that this manual and the rules for safe operation

be copied and posted near the unit installation site.

Safety should be stressed to all operators and potential

operators of this equipment.

Throughout this publication and on tags and decals

affixed to the generator, DANGER, WARNING, and

CAUTION blocks are used to alert personnel to special

instructions about a particular operation that may be

hazardous if performed incorrectly or carelessly. Observe

them carefully. Their definitions are as follows:

NOTE: Notes provide additional information important to

a procedure or component.

These safety warnings cannot eliminate the hazards they

indicate. Observing safety precautions and strict

compliance with the special instructions while performing

the action or service are essential to preventing accidents.

The operator is responsible for proper and safe use of

the equipment. The manufacturer strongly recommends

that if the operator is also the owner, to read the Owner’s

Manual and thoroughly understand all instructions before

using this equipment. The manufacturer also strongly

recommends instructing other users to properly start and

operate the unit. This prepares them if they need to

operate the equipment in an emergency.

How to Obtain Service

When the generator requires servicing or repairs, contact

an Independent Authorized Service Dealer for assistance.

Service technicians are factory-trained and are capable of

handling all service needs. For assistance locating a

dealer, go to

www.generac.com/Service/DealerLocator/.

When contacting a dealer about parts and service,

always supply the complete model number and serial

number of the unit as given on its data decal, which is

located on the generator. Refer to Figure 2-1 and Figure

2-2 for decal location. Record the model number and

serial numbers in the spaces provided on the inside front

cover of this manual.

Safety Rules

Study these SAFETY RULES carefully before installing,

operating or servicing this equipment. Become familiar

with this Owner’s Manual and with the unit. The

generator can operate safely, efficiently and reliably only

if it is properly installed, operated and maintained. Many

accidents are caused by failing to follow simple and

fundamental rules or precautions.

The manufacturer cannot anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual and on tags and decals affixed to the unit are,

therefore, not all-inclusive. If using a procedure, work

method, or operating technique the manufacturer does not

specifically recommend, verify that it is safe for others.

Also, make sure the procedure, work method or operating

technique utilized does not render the generator unsafe.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

Section 1: Safety Rules & General Information

2 Owner’s Manual for 60 Hz Air-cooled Generators

General Hazards

Inspect the generator regularly, and contact the nearest

Independent Authorized Service Dealer for parts needing

repair or replacement.

(000190)

DANGER

Loss of life. Property damage. Installation must always

comply with applicable codes, standards, laws and

regulations. Failure to do so will result in death

or serious injury.

Automatic start-up. Disconnect utility power and

render unit inoperable before working on unit.

Failure to do so will result in death or serious injury.

(000191)

DANGER

(000187)

WARNING

(000209a)

WARNING

This product is not intended to be used in

a critical life support application. Failure to

adhere to this warning could result in

death or serious injury.

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death

or serious injury.

(000182)

WARNING

This unit is not intended for use as a prime power

source. It is intended for use as an intermediate power

supply in the event of temporary power outage only.

See individual unit specifications for required

maintenance and run times pertaining to use.

(000247)

(000155)

WARNING

Only a trained and licensed electrician should perform

wiring and connections to unit. Failure to follow proper

installation requirements could result in death, serious

injury, and damage to equipment or property.

(000115)

WARNING

Moving Parts. Do not wear jewelry when

starting or operating this product. Wearing

jewelry while starting or operating this product

could result in death or serious injury.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and

appendages away from moving parts. Failure

to do so could result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces

could result in severe burns or fire.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

WARNING

Risk of injury. Do not operate or service this

machine if not fully alert. Fatigue can impair the

ability to service this equipment and could result

in death or serious injury.

(000215)

WARNING

Environmental Hazard. Always recycle batteries at an

official recycling center in accordance with all local

laws and regulations. Failure to do so could result in

environmental damage, death or serious injury.

(000228)

WARNING

Injury and equipment damage. Do not use

generator as a step. Doing so could result in falling,

damaged parts, unsafe equipment operation,

and could result in death or serious injury.

(000216)

Section 1: Safety Rules & General Information

Owner’s Manual for 60 Hz Air-cooled Generators 3

Exhaust Hazards

Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of

the generator. The generator must be installed and

operated outdoors only.

Electrical Hazards

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000150)

DANGER

Electrocution. Never connect this unit to the electrical

system of any building unless a licensed electrician

has installed an approved transfer switch. Failure to

do so will result in death or serious injury.

(000131a)

DANGER

Electrical backfeed. Use only approved switchgear to

isolate generator when electrical utility is the primary

power source. Failure to do so will result in death,

serious injury, and equipment damage.

(000152)

DANGER

Electrocution. Verify electrical system is

properly grounded before applying power.

Failure to do so will result in death or serious

injury.

(000188)

DANGER

Electrocution. Do not wear jewelry while

working on this equipment. Doing so will

result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power

source, if not avoided, will result in death

or serious injury.

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

Section 1: Safety Rules & General Information

4 Owner’s Manual for 60 Hz Air-cooled Generators

Fire Hazards

Comply with regulations the Occupational Safety and

Health Administration (OSHA) has established. Also,

verify that the generator is installed in accordance with

the manufacturer’s instructions and recommendations.

Following proper installation, do nothing that might alter a

safe installation and render the unit in noncompliance

with the aforementioned codes, standards, laws and

regulations.

Explosion Hazards

WARNING

Fire hazard. Do not obstruct cooling and

ventilating airflow around the generator. Inadequate

ventilation could result in fire hazard, possible

equipment damage, death or serious injury.

(000217)

WARNING

Fire and explosion. Installation must comply

with all local, state, and national electrical

(000218)

building codes. Noncompliance could result in unsafe

operation, equipment damage, death or serious injury.

WARNING

Fire hazard. Use only fully-charged fire

(000219)

extinguishers rated “ABC” by the NFPA. Discharged or

improperly rated fire extinguishers will not extinguish

electrical fires in automatic standby generators.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

WARNING

required safety equipment could result in

death or serious injury.

(000221)

Risk of electrocution. Refer to NFPA 70E for

safety equipment required when working with

with a live electrical system. Failure to use

(000147)

WARNING

Risk of Fire. Unit must be positioned in a

manner that prevents combustible material

accumulation underneath. Failure to do so

could result in death or serious injury.

(000192)

DANGER

(000151)

DANGER

Connection of fuel source must be done by a qualified

professional technician or contractor. Incorrect installation

of this unit will result in death, serious injury, and damage

to equipment and property damage.

(000174)

DANGER

Risk of fire. Allow fuel spills to completely dry

before starting engine. Failure to do so will

result in death or serious injury.

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

Section 2: General Information

Owner’s Manual for 60 Hz Air-cooled Generators 5

Section 2: General Information

The Generator

Figure 2-1. GH-410 Engine 8 kW Unit (Left) and GH-530 Engine 11 kW Unit (Right)

Figure 2-2. GT-990/GT-999 Engines, 16-22 kW Units

A. Exhaust Enclosure D. Battery Compartment G. Circuit Breakers J. Oil Fill Cap

B. Composite Base E. Fuel Regulator H. Control Panel K. Air Filter

C. Oil Filter F. Fuel Inlet (Back) I. Data Label L. Oil Dipstick

000908

L

B

C

D

E

F

G

H

K

J

I

A

000909

L

B

C

D

E

F

G

H

K

J

I

A

000910

B

L

C

D

E

K

F

G

H

J

I

A

Section 2: General Information

6 Owner’s Manual for 60 Hz Air-cooled Generators

Specifications

Generator

Engine

The specification sheet for your generator was included in the documentation provided with the unit at the time of

purchase. For additional copies, consult your local Independent Authorized Service Dealer for your specific generator

model.

Model 8 kW 11 kW 16 kW 20 kW 22 kW

Rated Voltage 240

Rated Maximum Load

Current (Amps) at Rated

Voltage*

33.3 45.8 66.6 83.3 91.7

Main Circuit Breaker 35 Amp 50 Amp 65 Amp 90 Amp 100 Amp

Phase 1

Rated AC Frequency 60 Hz

Battery Requirement

Group 26R, 12 Volts and 540 CCA Minimum (see Replacement Parts)

Enclosure Aluminum Aluminum/Steel Aluminum/Steel Steel Aluminum

Weight (lbs/kilos) 378/171.5

394/178.7 (Steel)

358/162.4 (Aluminum)

455/206.4 (Steel)

419/190 (Aluminum)

505/229 476/216

Normal Operating Range

This unit is tested in accordance to UL 2200 standards with an operating temperature of -20 ºF (-29 ºC) to 122 ºF

(50 ºC). For areas where temperatures fall below 32 ºF (0 ºC) a cold weather kit is recommended. When operated

above 77 ºF (25 ºC) there may be a decrease in engine power. (Please reference the engine specifications section.

These generators are rated in accordance with UL 2200, Safety Standard for Stationary Engine Generator Assemblies, and CSA-C22.2 No. 100-04

Standard for Motors and Generators.

* Natural Gas ratings will depend on specific fuel joules/Btu content. Typical derates are between 10-20% off the LP gas rating.

** Circuits to be moved must be protected by same size breaker. For example, a 15 amp circuit in the main panel must be a 15 amp circuit in the

transfer switch.

Model 8 kW 11 kW 16 kW 20/22 kW

Type of Engine GH-410 GTH-530 GT-990 GT-999

Number of Cylinders1222

Displacement 410 cc 530 cc 992 cc 999 cc

Cylinder Block Aluminum w/ cast iron sleeve

Recommended Spark Plug

see Replacement Parts

Spark Plug Gap 0.508 mm (0.020 in) 0.76 mm (0.030 in) 1.02 mm (0.040 in) 1.02 mm (0.040 in)

Valve Clearance 0.05 - 0.1 mm

(0.002 - 0.004 in)

0.05 - 0.1 mm

(0.002 - 0.004 in)

0.05 - 0.1 mm

(0.002 - 0.004 in)

0.05 - 0.1 mm

(0.002 - 0.004 in)

Starter 12 VDC

Oil Capacity Including Filter Approx. 1.5 qt/ 1.4 l Approx. 1.7 qt/ 1.6 l Approx. 1.9 qt/ 1.8 l Approx. 1.9 qt/ 1.8 l

Recommended Oil Filter

see Replacement Parts

Recommended Air Filter

see Replacement Parts

Engine power is subject to and limited by such factors as fuel Btu/joules, ambient temperature and altitude. Engine power decreases about 3.5 percent

for each 1000 feet (304.8 meters) above sea level, and also will decrease about 1 percent for each 6 ºC (10 ºF) above 15 ºC (60 ºF) ambient temperature.

Section 2: General Information

Owner’s Manual for 60 Hz Air-cooled Generators 7

Protection Systems

The generator may have to run for long periods of time

with no operator present to monitor the engine/generator

conditions. Therefore, the generator is equipped with a

number of systems to automatically shut down the unit to

protect it against potentially damaging conditions. Some

of these systems are as follows:

Alarms:

Warnings:

The control panel contains a display which alerts the

operator when a fault condition occurs. The above list is

not all inclusive. For more information about alarms and

control panel operation, see Section 3 Operation.

NOTE: A warning will indicate a condition, on the

generator, that should be addressed but not shut the

generator down. An alarm will shut the generator down to

protect the system from any damage. In the event of an

alarm, an owner can clear the alarm and restart the

generator prior to contacting an Independent Authorized

Service Dealer. If the intermittent issue occurs again,

contact an Independent Authorized Service Dealer.

Emission Information

The United States Environmental Protection Agency (US

EPA) (and California Air Resources Board (CARB), for

engines/equipment certified to California standards)

requires that this engine/equipment complies with

exhaust and evaporative emissions standards. Locate

the emissions compliance decal on the engine to

determine applicable standards. For emissions warranty

information, please reference the included emissions

warranty. It is important to follow the maintenance

specifications in Section 4 Maintenance to ensure that

the engine complies with the applicable emissions

standards for the duration of the product’s life.

This generator is certified to operate on Liquid Propane

Vapor fuel or pipeline Natural Gas.

The Emission Control System code is EM (Engine

Modification). The Emission Control System on this

generator consists of the following:

Fuel Requirements

The engine has been fitted with a dual fuel carburetion

system. The unit will run on natural gas or LP gas

(vapor), but it has been factory set to run on natural gas.

The fuel system will be configured for the available fuel

source during installation.

Recommended fuels should have a BTU content of at

least 1000 Btus per cubic foot (37.26 megajoules per

cubic meter) for natural gas, or at least 2500 BTUs per

cubic foot (93.15 megajoules per cubic meter) for LP gas

(vapor).

NOTE: If converting to LP gas from natural gas, a

minimum LP tank size of 250 gallons (946 liters) is

recommended. See the Installation Manual for complete

procedures and details.

Battery Requirements

Group 26R, 12V, minimum 540 CCA.

For proper battery maintenance procedures, see Section

4 Maintenance.

Battery Charger

The battery charger is integrated into the control panel

module in all models. It operates as a Smart Charger

which ensures output charging levels are safe and

continuously optimized to promote maximum battery life.

Engine Oil Requirements

For proper oil viscosity, see chart in Figure 4-1.

• High Temperature

• Low Oil Pressure

• Overcrank

• Overspeed

• Overvoltage

• Undervoltage

• Overload

• Underspeed

• RPM Sensor Loss

• Controller Fault

• Wiring Error

• Fuse Problem

• Stepper Overcurrent

• Charger Warning

• Charger Missing AC

• Low Battery

• Battery Problem

• Exercise Set Error

• USB Warning

• Download Failure

System Components

Air Induction

- Intake Manifold

- Air Cleaner

Fuel Metering

- Carburetor and Mixer Assembly

- Fuel Regulator

Ignition

- Spark Plug

- Ignition Module

Exhaust

- Exhaust Manifold

- Muffler

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

Section 2: General Information

8 Owner’s Manual for 60 Hz Air-cooled Generators

Replacement Parts

Accessories

Performance enhancing accessories are available for air-cooled generators.

NOTE: Contact an Independent Authorized Service Dealer or visit www.generac.com for additional information on

replacement parts, accessories, and extended warranties.

Description 8 kW 11 kW 16 kW 20 kW 22 kW

26R Exide Battery 0H3421S

Spark Plug 0G0767B 0E9368 0E7585A 0G0767A 0G0767A

Oil Filter 070185E

Air Filter 0E9371A 0J8478

Control Panel Fuse 0D7178T

Transfer Switch Fuses 073590A

Accessory Description

Cold Weather Kit Recommended in areas where temperatures fall below 32 ºF (0 ºC).

Scheduled Maintenance Kit Includes all pieces necessary to perform maintenance on the generator along

with oil recommendations.

Auxiliary Transfer Switch Lockout Enables any of the transfer switches to completely lock out one large electrical

load by tying into its control system.

Fascia Base Wrap The fascia base wrap snaps together around the bottom of the new air-cooled

generators. This offers a sleek, contoured appearance as well as offering

protection from rodents and insects by covering the lifting holes located in the

base. Requires use of the mounting pad shipped with the generator.

Mobile Link™ (USA only) Provides a personalized web portal that displays the generator status,

maintenance schedule, event history and much more. This portal is accessible

via computer, tablet or smart phone. Sends emails and/or text notifications the

moment there is any change in the generator’s status. Notification settings can

be customized to what type of alert is sent and how often. For more

information, visit www.MobileLinkGen.com.

Touch-Up Paint Kit Very important to maintain the look and integrity of the generator enclosure.

This kit includes touch-up paint and instructions.

Wireless Local Monitor Completely wireless and battery powered, the Wireless Local Monitor provides

you with instant status without ever leaving the house. Status lights (red,

yellow and green) alert owners when the generator needs attention. Magnetic

backing permits refrigerator mounting and gives a 600 foot line of sight

communication.

Extended Warranty Coverage Extend your generator warranty coverage by purchasing extended warranty

coverage. Covers both parts and labor. Extended coverage can be purchased

within 12 months of the end-users purchase date.

This extended coverage is applicable to registered units and end-user proof of

purchase must be available upon request.

Available for Generac

®

, Guardian

®

and Centurion

®

products. Not available for

Corepower™ and EcoGen™ products or all international purchases.

Section 3: Operation

Owner’s Manual for 60 Hz Air-cooled Generators 9

Section 3: Operation

Site Prep Verification

It is important that the generator is installed in such a way

that the airflow into and out of the generator is not

impeded. Verify that all shrubs or tall grasses have been

removed within 3 ft. (0.91m) of the intake and discharge

louvers on the sides of the enclosure. It is also important

that the generator is not subject to water intrusion. Verify

that all potential sources such as water sprinklers, roof

run-off, rain gutter down spouts and sump pump

discharges are directed away from the generator

enclosure.

Turn the generator OFF before performing maintenance.

Remove 7.5 Amp fuse, T1 and T2 battery charge fuses,

and disconnect battery cables to prevent accidental start

up. Disconnect the NEGATIVE (-) cable first, then

disconnect the POSITIVE (+) cable. When connecting

the cables, connect the POSITIVE cable first, the

NEGATIVE cable last.

Side Compartment

Local codes may require this compartment to be locked.

A hasp is provided so the owner/operator can secure the

compartment with a padlock. Check local codes for side

compartment locking requirements.

Figure 3-1. Open Side Compartment

Main Circuit Breaker (Generator Disconnect)

This is a 2-pole breaker rated according to relevant

specifications. See “A” in Figure 3-1.

LED Indicator Lights

See “B” in Figure 3-1.

• Green LED “Ready” light is on when utility is

present and the control panel button is in the AUTO

position. This also indicates when the generator is

running.

• Red LED “Alarm” light is on when the generator is

OFF or a fault is detected. Contact an authorized

servicing dealer.

• Yellow LED “Maintenance” light.

NOTE: Yellow LED may be on at the same time as either

the Red or Green LED.

120V GFCI Outlet/15 Amp Breaker

(16-22 kW Only)

Some units are equipped with an external 15 Amp, 120

volt GFCI c

onvenience outlet located in the top corner of

the compartment. See “C” in Figure 3-1.

When the generator is running, in the absence of utility

power, this outlet may also be used to power items

outside the home such as lights or power tools. This

outlet may also be used when utility power is present by

running the generator in manual mode.

This outlet does not provide power if the generator is not

running. Do not use this outlet when the generator is in

Exercise mode. This outlet is protected by a 15 Amp

circuit breaker in the side compartment.

Generator Enclosure

The lid will be locked. A set of keys is attached to the

circuit breaker box door with a cable tie.

1. Cut the cable tie to remove the keys.

2. Use the keys to open the lid of the generator.

NOTE: The enclosed keys provided with this unit are

intended for service personnel use only.

Automatic start-up. Disconnect utility power and

render unit inoperable before working on unit.

Failure to do so will result in death or serious injury.

(000191)

DANGER

(000182)

WARNING

000931

A

B

C

Section 3: Operation

10 Owner’s Manual for 60 Hz Air-cooled Generators

Figure 3-2. Circuit Breaker Box and Keys

(As Shipped)

3. There are two locks securing the lid, one on each

side (A in Figure 3-3). To properly open the lid,

press down, on the lid, above the side lock and

unlock the latch.

4. Repeat for the other side. If pressure is not applied

from the top, the lid may appear stuck.

NOTE: Always verify that the side locks are unlocked

before attempting to lift the lid.

5. Once the lid is open, remove the front access

panel by lifting it up and out.

NOTE: Always the lift the front access panel up before

pulling away from enclosure (B and C in Figure 3-3). Do

not pull the panel away from the enclosure before lifting

up (D in Figure 3-3).

Figure 3-3. Side Lock Location and Front Panel Removal

000932

000597

A

001028

B DC

Section 3: Operation

Owner’s Manual for 60 Hz Air-cooled Generators 11

Control Panel Interface

The Control Panel Interface is located under the lid of the

enclosure. Before attempting to lift the lid of the

enclosure, verify that both left and right side locks are

unlocked. To remove the front cover, lift the cover straight

up to disengage the side hooks, then tilt and lift it away

from the unit.

When closing the unit, verify that both left and right side

locks are securely locked.

NOTE: All appropriate panels must be in place during

any operation of the generator. This includes operation

by a servicing technician, while conducting

troubleshooting procedures.

Figure 3-4. Generator Control Panel

Using the Auto/Off/Manual Interface

NOTE: Damage caused by mis-wiring of the interconnect wires is not warrantable.

Interface Menu Displays

The LCD display

Menu System Navigation

To get to the MENU, use the “Escape” button from any page. It may require pressing it several times before getting to

the MENU page. Navigate to the desired menu by using the

↑/↓ buttons. When the desired menu is displayed and

flashing, press the “Enter” button. See Figure 3-5 Navigation Menu.

000425

Button Description of Operation

AUTO

Selecting this button activates fully automatic system operation. It also allows the unit to automatically

start and exercise the generator according to the exercise timer (see

Setting the Exercise Timer ).

OFF This button shuts down the engine and also prevents automatic operation of the unit.

MANUAL

This button will crank and start the generator. Transfer to standby power will not occur unless there is a

utility failure.

Feature Description

HOME page

The default page which will be displayed if no buttons are pressed for 60 seconds. This page normally

shows the current Status message and the current date and time. The highest priority active Alarm/

Warning will be automatically posted on this page as well as flashing the backlight when such a condi-

tion is detected. In the case of multiple Alarms/Warnings, only the first message will be displayed. To

clear an Alarm or Warning, press the OFF button and then press the ENTER key.

Display Backlight

Normally off. If the operator presses any button, the backlight will automatically light and remain on for

30 seconds.

MAIN MENU page

Allows the operator to navigate to all other pages or sub-menus by using the Arrows and Enter but-

tons. This page can be accessed at any time with several presses of the dedicated Escape button.

Each press of the Escape button takes the operator to the previous menu until the MAIN MENU dis-

plays. This page contains information for - History; Status; Edit; Debug.

Section 3: Operation

12 Owner’s Manual for 60 Hz Air-cooled Generators

Figure 3-5. Navigation Menu

EVOLUTION/SYNC2.0 HSB MENU MAP

“Run Log”

ESC

ENTER

SYSTEM

BAT-

DATE/TIME

SUB MENUS

HISTORY

EDI

Exercise Time



14:00 Wednesday



Firmware Update



Press Enter



ESC

ENTER

Current Date/Time



2/12/13 12:22



ESC

ENTER

ESC

ENTER

ESC

ENTER

ESC

ENTER

ENTERENTER

ENTER

ESC

Switched to “OFF”

Hours of Protection

0 (H)

Language



English



Fuel Selection



NG or LP



Firmware Update



Insert USB



“Alarm Log”

- Alarm Log +

- Run Log +

- 1 thru 50 +

Warning Message(s)

Charger Warning

Charger Missing AC

Low Battery

Battery Problem

Exercise Set Error

USB Warning

Download Failure

Running Manual

Running-Utility Lost

Running-Remote Start

Running-2 Wire Start

Running - Exercise

Switched Off

Stopped - Auto

Stopped - Alarm

Alarm Message(s)

High Temperature

Low Oil Pressure

Overcrank

Overspeed

Overvoltage

Undervoltage

Overload

Underspeed

RPM Sensor Loss

Controller Fault

Wiring Error

Stepper Overcurrent

Fuse Problem*

ESC

Select Min (0-59)

- 0 +

ESC

Select Hour (0-23)

- 14 +

ESC ESC

Quiet Test Mode

?

Select Frequency

- WEEKLY +

- BIWEEKLY +

- MONTHLY +

Quiet Test Mode only

on certain models

Language

+ English -

Fuel Selection

+ NG or LP -

ENTER

Cold Smart Start?



YES or NO



ESC

Cold Smart Start?

- YES or NO +

Language

+ Espanol -

+

-

+

-

Battery Condition

“Good” “Inspect Battery” or “Check Battery”

*“Fuse Problem” on Firmware

1.11 and older ONLY

Note: Menu functions and features may vary

depending on unit model and firmware revision.

Section 3: Operation

Owner’s Manual for 60 Hz Air-cooled Generators 13

Figure 3-6. Navigation Menu

UP ARROW =

+

DOWN ARROW =

-

ESC

MAIN

DEALER

EXAMPLE:

Inspect Battery 200 RnHr or 12/27/13

and

Next Maintenance 200 RnHr or 12/27/13

Current Date/Time

02/14/13 07:40

ESC

ENTER

ESC ENTER

ESC

ESC ESC

ENTER

ENTERENTER

ESC

MAINT:

Maint. Log

Run Hrs

Scheduled

ENTER

Select Month (1-12)

- 2 +

Run Hours (H)

0.0

ENTER

Select Date (1-31)

- 13 +

ENTER

Select Year (0-99)

- 13 +

ENTER

Access Requires Password

Possible Message(s)

Corrupted File

Invalid File

File Not Found

Unsupported Device

"Current:V XXXX "

"USB: V XXXX"

"Are You Sure?"

"- Yes or No +"

ESC

ENTER

ESCENTER

Select “Yes” then Press “Enter” to continue or Press “ESCAPE” to escape out of updating.

During update process the Blue “Manual” light flashes, then the Green “Auto” light flashes.

Sequence does this twice. When update is complete the unit returns to Install Wizard menu.

When the controller powers up the very first screen displays the version number for a few seconds.

When update is complete remove Thumb Drive, then follow the Install Wizard Menu.

- 1 thru 50 +

"Battery Maintained"

"Schedule A Serviced"

"Schedule B Serviced"

"Maintenance Reset"

"Inspect Battery"

"Service Schedule A"

"Service Schedule B"

ESC

Select Min (0-59)

- 0 +

ESC

Select Hour (0-23)

- 14 +

Language

+ Francais -

Language

+ Portuguese -

+

-

+

Select Day

- Wednesday +

000428b

Section 3: Operation

14 Owner’s Manual for 60 Hz Air-cooled Generators

Setting the Exercise Timer

This generator is equipped with a configurable exercise

timer. There are two settings for the exercise timer.

Day/Time: Once set, the generator will start and exercise

for the period defined, on the day of the week and at the

time of day specified. During this exercise period, the unit

runs for approximately 5 or 12 minutes, depending on the

model, and then shuts down.

Exercise frequency (how often the exercise will take

place): It can be set to Weekly, Biweekly or Monthly. If

Monthly is selected, the day of the month must be

selected from 1-28. The generator will exercise on that

day each month. Transfer of loads to the generator

output does not occur during the exercise cycle unless

utility power is lost.

NOTE: If the installer tests the generator prior to

installation, press the “enter” button to skip setting up the

exercise timer.

NOTE: The exercise feature will operate only when the

generator is placed in the AUTO mode and will not work

unless this procedure is performed. The current date/time

will need to be reset every time the 12 volt battery is

disconnected and then reconnected, and/or when the

fuse is removed.

Table 3-1 details the exercise information and

programming options for all Home Standby generators.

Figure 3-7 illustrates the engine speed profile during a

typical exercise cycle for 22 kW generators. Figure 3-8

shows the engine speed profile for 16-20 kW generators.

8-11 kW generators exercise at a constant 3600 rpm.

While providing the necessary periodic exercise

operation, the lower rpm also reduces fuel consumption,

engine wear and noise.

Figure 3-7.

Figure 3-8.

Battery Charger

NOTE: The battery charger is integrated into the control

module in all models.

The battery charger operates as a Smart Charger that

ensures:

• Output is continually optimized to promote

maximum battery life.

• Charging levels are safe.

NOTE: A warning is displayed on the LCD when the

battery needs service.

Manual Transfer Operation

2600

2800

3000

3200

3400

3600

3800

Low Speed Exercise Profile - 22 kW Generators

1800

2000

2200

2400

0 sec 5 s 10 s 15 s 20 s 25 s 30 s 35 s 40 s 45 s 1 min 5 min

Exercise Speed (RPM)

Exercise Time

000905

Low Speed Exercise Profile - 16 to 20 kW Generators

2600

2800

3000

3200

2000

2200

2400

Exercise Speed (RPM)

000906

0 sec 5 s 10 s 1 min 5 min

Exercise Time

Table 3-1. Generator Exercise Characteristics

Generator Size 8 kW 11 kW 16 kW / 20 kW 22 kW

Low Speed Exercise n/a * n/a * 2400 rpm 1950 rpm

Exercise Frequency

Options

Weekly/Bi-Weekly/

Monthly

Weekly/Bi-Weekly/

Monthly

Weekly/Bi-Weekly/

Monthly

Weekly/Bi-Weekly/

Monthly

Exercise Time Length 12 minutes 12 minutes 5 minutes 5 minutes

* exercises at 3600 rpm

(000132)

DANGER

Electrocution. Do not manually transfer under load.

Disconnect transfer switch from all power sources

prior to manual transfer. Failure to do so will result

in death or serious injury, and equipment damage.

Section 3: Operation

Owner’s Manual for 60 Hz Air-cooled Generators 15

Prior to automatic operation, manually exercise the

transfer switch to verify that there is no interference with

proper operation of the mechanism. Manual operation of

the transfer switch is required if electronic operation

should fail.

Transfer to Generator Power Source

1. Verify generator is in the OFF mode.

2. Set the main circuit breaker (Generator

Disconnect) to OFF or OPEN.

3. Turn off the utility power supply to the transfer

switch using the means provided (such as a utility

main line circuit breaker).

4. Use the manual transfer handle (A in Figure 3-9)

inside the transfer switch to move the main

contacts to the STANDBY position (loads

connected to the standby power source).

5. To crank and start the engine, press the control

panel MANUAL button.

6. Allow the engine to stabilize and warm up for a few

minutes.

7.

Set the main circuit breaker (Generator Disconnect)

to ON or CLOSED. The standby power source now

powers the loads.

Figure 3-9. Manual Transfer Switch Operation

Transfer Back to Utility Power Source

When utility power has been restored, transfer back to

utility source and shut down the generator. To manually

transfer back to utility power and shut down the

generator:

1. Set the Main Circuit Breaker (Generator

Disconnect) to OFF or OPEN.

2. Allow the engine to run for 2 minutes at no-load to

stabilize the internal temperatures.

3. Press the control panel OFF button. The engine

should shut down.

4. Verify that utility power supply to the transfer switch

is turned OFF.

5. Use the manual transfer handle (A in Figure 3-9)

inside the transfer switch to move the main

contacts back to the UTILITY position (loads

connected to the utility power source).

6. Turn on the utility power supply to the transfer

switch using the means provided.

7. Press the control panel AUTO button.

000228

A

B

MANUAL

• Will not transfer to generator if utility is present.

• Will transfer to generator if utility fails (below 65% of nominal for 5 consecutive seconds).

• Will transfer back when utility returns for 15 consecutive seconds. The engine will continue to

run until removed from the MANUAL mode.

AUTO

• Will start and run if utility fails for 5 consecutive seconds. (factory default)

• Will start a 5 second engine warm-up timer.

–Will not transfer if utility subsequently returns.

–Will transfer to generator if utility is not present.

• Will transfer back to utility once utility returns (above 80% of nominal) for 15 seconds.

• Will not transfer back to utility unless utility returns. The generator will shut down if the OFF

button is pressed or a shutdown alarm is present.

• Once utility power is returned, the generator will shut down after 1 minute cool-down time.

EXERCISE

• Will not exercise if generator is already running in either AUTO or MANUAL mode.

• During exercise, the controller will only transfer if utility fails during exercise for 10 seconds,

and will switch to AUTO.

Section 3: Operation

16 Owner’s Manual for 60 Hz Air-cooled Generators

Automatic Transfer Operation

To select automatic operation:

1. Make sure the transfer switch main contacts are

set to the UTILITY position (loads connected to the

utility power source).

2. Be sure that normal UTILITY power source voltage

is available to transfer switch terminal lugs N1 and

N2.

3. Press the AUTO button on the control panel

interface.

4. Set the main circuit breaker (Generator

Disconnect) to the ON (Closed) position.

With these steps complete, the generator will start

automatically when utility source voltage drops below a

preset level. After the unit starts, loads are transferred to

the standby power source.

Automatic Sequence of Operation

Utility Failure

With the generator set to AUTO, when utility fails (below

65% of nominal) a 5 second (dealer programmable) line

interrupt delay time is started. If utility is still gone when

the timer expires, the engine will crank and start. Once

started, a 5 second engine warm-up timer will be

initiated. When the warm-up time expires, the controller

will transfer the load to the generator. If the utility power is

restored (above 80% nominal) at any time from the

initiation of the engine start until the generator is ready to

accept load (5 second warm-up time has not elapsed),

the controller will complete the start cycle and run the

generator through its normal cool down cycle, however,

the load will remain on the utility source.

Cranking

The system will control the cyclic cranking as follows:

• 8 kW Unit: 5 cranking cycles as follows: 15 second

crank, seven (7) second rest, followed by four (4)

additional cycles of seven (7) second cranks

followed by seven (7) second rests.

• 11 - 22 kW Units: 5 cranking cycles as follows: 16

second crank, seven (7) second rest, 16 second

crank, seven (7) second rest, followed by three (3)

additional cycles of seven (7) second cranks

followed by seven (7) second rests.

Cold Smart Start

The Cold Smart Start feature can be enabled in the EDIT

menu. With Cold Smart Start enabled, the generator will

monitor ambient temperature and the warm-up delay will

be adjusted based on prevailing conditions.

On a startup in AUTO mode, if the ambient temperature

is below a fixed temperature (based on model) the

generator will warm-up for 30 seconds. This allows the

engine to warm before a load is applied. If the ambient

temperature is at or above the fixed temperature, the

generator will startup with the normal warm-up delay of 5

seconds.

When the generator engine is started, a check for proper

output voltage build up will be performed.

If some condition impedes normal voltage creation, such

as frost crystals or dust/dirt prevent a good electrical

connection, the start sequence will be interrupted so that

a cleaning cycle of the internal electrical connections can

be attempted.

The cleaning cycle is an extended “Warming Up” period

which lasts for several minutes while the normal

generator voltage output is determined to be low. During

this cycle, the generator controller will display the

“Warming Up” on the display screen.

If the cleaning cycle fails to clear the obstruction, the

generator controller display will show the “Under Voltage”

message.

After several minutes, the alarm message can be

cleared, and a restart of the generator attempted.

If the problem persists, make no further attempts to start.

Contact an independent authorized service dealer.

Load Transfer

The transfer of load when the generator is running is

dependent upon the operating mode:

Shutting Generator Down While

Under Load

IMPORTANT NOTE: To turn the generator off during

utility outages to perform maintenance, or conserve fuel,

follow these steps:

To turn the generator OFF (while running in

AUTO and online):

1. Turn the main utility disconnect OFF.

2. Turn the main line circuit breaker (MLCB) on the

generator to OFF (OPEN).

3. Turn the generator OFF.

To turn the generator back ON:

1. Put the generator back into AUTO and allow to

start and warm-up for a few minutes.

2. Set the MLCB on the generator to ON.

The system will now be operating in automatic mode.

The main utility disconnect can be turned ON (CLOSED).

To shut the unit OFF, this complete process must be

repeated.

La page charge ...

Generac 16 kW G0062573 Manuel utilisateur

Generac 16 kW G0062573 Manuel utilisateur

dans d''autres langues