LG WT7305CW Le manuel du propriétaire

OWNER'S MANUAL

WASHING MACHINE

Read this owner's manual thoroughly before operating the

appliance and keep it handy for reference at all times.

ENGLISH

WT7305C*

MFL68267085

Rev.01_100620

www.lg.com

TABLE OF CONTENTS

2

3 IMPORTANT SAFETY

INSTRUCTIONS

3 READ ALL INSTRUCTIONS BEFORE USE

3 WARNING STATEMENTS

6 CAUTION STATEMENTS

7 PRODUCT OVERVIEW

7 Product Features

9 INSTALLATION

9 Before Installing

10 Choosing the Proper Location

11 Unpacking and Removing Shipping Material

11 Connecting the Water Inlet Hoses

12 Connecting the Drain Hose

13 Leveling the Washer

14 Final Installation Check

16 OPERATION

16 Before Use

17 Sorting Laundry

18 Loading the Washer

19 Adding Cleaning Products

21 Control Panel

24 Wash Cycles

27 Cycle Modifiers

27 Special Care Features

28 Options and Extra Functions

31 SMART FUNCTIONS

31 LG ThinQ Application

33 Smart Diagnosis

TM

Function

35 MAINTENANCE

35 Regular Cleaning

35 Periodic Maintenance

38 Care in Cold Climates

40 TROUBLESHOOTING

40 Before Calling for Service

48 LIMITED WARRANTY

48 USA

51 CANADA

3IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what may happen if the instructions are not followed.

WARNING STATEMENTS

WARNING

• To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this

product, follow basic precautions, including the following:

Installation

• Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and

safety glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Before use, the appliance must be properly installed as described in this manual.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions

are packed with the appliance for the installer’s reference. If the appliance is moved to a new location,

have it checked and reinstalled by qualified service personnel.

• Moving or installation of the appliance requires two or more people.

• Do not install the appliance in humid spaces.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions.

• This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or

aircraft.

• Strongly recommend not using a drain pan when installing this appliance, as standing water in the drain

pan may increase the risk of electric shock, injury, or death.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages

will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

4 IMPORTANT SAFETY INSTRUCTIONS

• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children

might use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight

chambers.

• The appliance must be installed and electrically grounded by qualified service personnel in accordance

with local codes.

• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.

• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

• This appliance must be positioned near to an electrical power supply.

• Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• Use new hoses when connecting the appliance to the water supply. Do not reuse old hoses.

Operation

• Read all instructions before using the appliance and save these instructions.

• Use this appliance only for its intended purpose.

• If the product has been submerged in water, sitting in standing water, or waterlogged, do not come in

contact with the product and immediately contact an LG Electronics customer information center for

instructions before resuming use.

• If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug

it immediately, and contact an LG Electronics Customer Information Center.

• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for

such a period, before using the appliance, turn on all hot water faucets and let the water flow from each

for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

• Do not reach into the washer if the tub or drum, agitator, or any interior parts are moving. Before

loading, unloading, or adding items, press Start/Pause and allow the tub or drum to coast to a complete

stop before reaching inside.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• Do not allow children or pets to play on, in or with the appliance. Close supervision is necessary when the

appliance is used near children or pets.

• Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on

product labels.

• Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage along its length or at either end.

• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight

out from the outlet.

• Do not use an extension cord or adapter with this appliance.

• Do not grasp the power cord or touch the appliance controls with wet hands.

• Do not modify or extend the power cord.

• If the electrical supply cord is damaged, it must only be replaced by the manufacturer or its service agent

or a similar qualified person in order to avoid a hazard.

• Do not put oily or greasy clothing, candles or flammable materials on top of the appliance.

• Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags,

etc.), gasoline, chemicals and other flammable vapors and liquids.

5IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

• Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when

using laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the

finish.

• Do not wash laundry that has been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, vegetable or cooking oil, or other flammable or explosive substances, as they give

off vapors that could ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash

water. These substances give off vapors that could ignite or explode.

• In the event of a gas leak (propane gas, LP gas, etc.), do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

• Do not tamper with controls.

• Fix the drain hose securely in place to avoid flooding.

• Do not abuse, sit on, or stand on the lid of the appliance.

• Keep hands and foreign objects clear of the lid and latch area when closing the lid.

• Always check the inside of the appliance for foreign objects.

Maintenance

• Do not repair or replace any part of the appliance. All repairs and servicing must be performed by

qualified service personnel unless specifically recommended in this owner’s manual. Use only authorized

factory parts.

• Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply.

• Remove any dust or foreign matter from the power plug pins.

• Do not disassemble or repair the appliance by yourself.

• Remove the lid before the appliance is removed from service or discarded to avoid the danger of

children or small animals getting trapped inside.

• Make sure the dispenser drawer or lid is closed at all times when not being filled with laundry products.

Grounding Instructions

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

with a qualified electrician or service personnel if you are in doubt whether the appliance is properly

grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

• The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the

risk of electric shock by providing a path of least resistance for electric current. The appliance is

equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes

and ordinances.

6 IMPORTANT SAFETY INSTRUCTIONS

CAUTION STATEMENTS

CAUTION

• To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or

property when using this product, follow basic precautions, including the following:

Installation

• Install the product on a firm and level floor.

Operation

• Do not place objects on top of the appliance.

• Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period

of time, such as during vacations.

• ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

• Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

• Do not combine laundry products for use in one load unless specified on the label.

• Do not touch draining water which may be hot.

• If the drain hose and the water inlet hose are frozen in winter, defrost them before using the appliance.

• Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the

appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.

• Clothing or articles that are waterproof or water resistant must be washed in the Waterproof cycle only.

(Examples include water resistant clothing, mattress covers, outdoor clothes, plastic mats.) Using

another cycle may result in personal injury or damage to the washer, clothes, walls, floor, and

surrounding objects due to abnormal vibration.

7PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

NOTE

• For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction, property damage or bodily injury caused by the use of separately

purchased unauthorized components, parts, or non-LG products.

Front View

a Lid

b Control Panel

c Detergent Dispenser Drawer

d Liquid Bleach Compartment

e Tub

f Leveling Feet

Rear View

a Water Inlets

b Power Cord

c Drain Hose

8 PRODUCT OVERVIEW

Accessories

Included Accessories

a Tie Strap

Required Accessories

a Hot and Cold Water Hoses

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Model WT7305C*

Electrical Requirements 120 VAC @ 60 Hz

Min. / Max. Water Pressure 20 - 120 psi (138 - 827 kPa)

Dimensions (Width X Depth X Height) 27" X 28 3/8" X 44 1/2" (68.6 cm X 72.1 cm X 113 cm)

Maximum Height with Lid Open 57 1/4” (145.3 cm)

Net Weight 130.0 lb (59 kg)

Max. Spin Speed 950 RPM (±50 rpm)

9INSTALLATION

ENGLISH

INSTALLATION

Before Installing

WARNING

• Moving or installation of the appliance requires two or more people. Failure to follow these instructions

may result in injury.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed

to outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious

injury, fire, electric shock, or death.

• Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

• To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

• To ensure proper airflow, do not block the large opening on the bottom of the washer with carpeting or

other materials.

• Do not remove the ground prong from the power cord. Do not use an adapter or extension cord. Plug

into a grounded 3-prong outlet. Failure to follow this warning can cause serious injury, fire, electric

shock, or death.

• Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump,

motor, noise filter cover, and heater (on applicable models).

Installation Overview

Please read the following installation instructions first after purchasing this washer or transporting it to

another location.

a Choosing the Proper Location

b Unpacking and Removing Shipping Material

c Connecting the Water Inlet Hoses

d Connecting the Drain Hose

e Leveling the Washer

ab c

d

ef

10 INSTALLATION

f Connecting to the Power Supply

g Final Installation Check

Tools Needed

a Pliers

b Flat-Blade Screwdriver

c Level

Choosing the Proper

Location

Check the following requirements for the install

location before installing the washer.

• Allow for sufficient space between the walls and

the washer for installation.

• Make sure that the floor is clean, dry and free of

dust, dirt, water and oil so the leveling feet

cannot slide easily. Leveling feet that can move

or slide on the floor can contribute to excess

vibration and noise.

• If the floor has too much flex, reinforce it to

make it more rigid. If the floor is not solid, it may

cause severe vibration and noise.

Power Outlet

The power outlet must be within 60 inches (1.5 m)

of either side of the washer.

• Position the washer so that the outlet and plug

are easily accessible.

• Do not overload the outlet with more than one

appliance.

• The outlet must be grounded in accordance with

current electrical wiring codes and regulations.

• Use a time-delay fuse or circuit breaker.

• It is the personal responsibility and obligation of

the washer owner to have a proper outlet

installed by a qualified electrician.

Flooring

• To minimize noise and vibration, install the

washer on a level, solidly constructed floor

capable of supporting the washer without

flexing or bouncing.

• The washer must be installed on firm flooring to

minimize vibration during the spin cycle.

Concrete flooring is best, but a wood floor is

sufficient, provided it is built to FHA standards.

• The floor under the washer must not slope more

than 1 inch (2.5 cm) from front to back or side to

side.

• Installing on carpeting and soft tile surfaces is

not recommended.

• Never install the washer on a platform or weakly

supported structure.

Floor Installation

To ensure sufficient clearance for water inlet

hoses, drain hose and airflow, allow minimum

clearances of at least 1 inch (2.5 cm) at the sides

and 4 inches (10 cm) behind the washer. Be sure

to allow for wall, door, or floor moldings that may

increase the required clearances.

Minimum vertical space from floor to overhead

shelves, cabinets, ceilings, etc., is 58 inches (147

cm).

Dimensions and Clearances

A 1” (2.5 cm)

B 27” (68.6 cm)

C 44 1/2” (113 cm)

C

BAA

D

E

H

G

F

11INSTALLATION

ENGLISH

Unpacking and Removing

Shipping Material

Remove all shipping materials from the washer for

proper operation and inspect it for shipping

damage.

CAUTION

• Failure to remove shipping materials can cause

excessive noise and vibration.

Unpacking Shipping Material

1 Lift the washer off of the foam base.

• After removing the carton and shipping

material, lift the washer off the foam base.

• Make sure the plastic tub support

a comes

off with the base and is not stuck to the

bottom of the washer.

• If you must lay the washer down to remove

the carton base

b, always protect the side

of the washer and lay it carefully on its side.

Do not lay the washer on its front or back.

2 Remove the foam tub insert.

• To prevent damage, do not remove the

foam insert

c containing the owner’s

manual, parts, and laundry product

samples from the tub until the washer is in

the final location.

NOTE

•Once removed, save the foam insert for future

use. If the washer needs to be moved, the foam

insert will help prevent damage during

transportation.

3 Unfasten the power cord.

• Unfasten the power cord from the back of

the washer.

Connecting the Water Inlet

Hoses

To avoid the risk of costly water damage, purchase

and install new inlet hoses when installing the

washer.

WARNING

• Do not overtighten the hoses or cross-thread the

hose fittings. Overtightening or cross-threading

can damage the valves or couplings, resulting in

leaking and property damage.

• Do not reuse old hoses. Use only new hoses

when installing the washer. Old hoses could leak

or burst causing flooding and property damage.

Contact an LG Customer Information Center for

assistance in buying hoses.

NOTE

• Periodically check the hoses for cracks, leaks,

and wear, and replace the hoses every five years.

D 57 1/4” (145.3 cm)

E 26 3/4” (68 cm)

F 3 1/2” (9 cm)

G 32” (81.1 cm)

H 28 3/8” (72.1 cm)

Dimensions and Clearances

12 INSTALLATION

NOTE

• Do not stretch the water hoses intentionally, and

make sure that they are not pinched, crushed or

kinked by other objects.

• Water supply pressure must be between 20 psi

and 120 psi (138 - 827 kPa). If the water supply

pressure is more than 120 psi, a pressure

reducing valve must be installed.

• Your hot water heater should be set to deliver

water at 120 - 135°F (48 - 57°C) to allow the

washer to properly control wash temperatures.

• Do not store or install the washer in a location

subject to freezing temperatures. Damage to the

water inlet hoses and internal mechanisms of

the washer can result. If the washer was

exposed to freezing temperatures prior to

installation, allow it to stand at room

temperature for several hours before use and

check for leaks prior to operation.

• Do not use flood-preventing hoses with auto

shutoff devices. The devices can be tripped

during fill and prevent the washer from filling

properly.

How to Connect the Water Inlet

Hoses

1 Check the fittings and seals.

• Inspect the threaded fitting on each hose

and make sure there is a rubber seal

a in

place in both ends of each hose to prevent

leaking.

2 Connect the water supply hoses.

• Connect the water inlet hoses to the hot

and cold water faucets tightly by hand and

then tighten another 2/3 turn with pliers.

• Connect the blue hose to the cold water

faucet and the red hose to the hot water

faucet.

3 After the hoses are connected, turn on the

water faucets and flush out any foreign

substances such as dirt, sand, or sawdust.

• Let the water drain into a bucket, and check

the water temperature to make sure you’ve

connected the hoses to the correct faucets.

4 Attach the inlet hoses to the back of the

washer.

• Attach the hot water inlet hose to the hot

water inlet on the back of the washer.

Attach the cold water inlet hose to the cold

water inlet on the back of the washer.

• Tighten the fittings securely. Turn on both

faucets all the way and check for leaks at

both ends of the hoses.

Connecting the Drain Hose

Connect the drain hose to either a standpipe or

laundry tub.

WARNING

• The drain hose should always be properly

secured. Failure to properly secure the drain

13INSTALLATION

ENGLISH

hose can result in flooding and property

damage.

NOTE

• The drain must be installed in accordance with

any applicable local codes and regulations.

• Make sure that the drain hose is not stretched,

pinched, crushed, or kinked.

• Do not install the drain hose with the end lower

than 29.5 inches (75 cm) or higher than 96

inches (244 cm) above the bottom of the washer

or more than 60 inches (152 cm) away from the

washer.

• Never create an airtight seal between the hose

and the drain with tape or other means. If no air

gap is present, water can be siphoned out of the

tub resulting in poor wash/rinse performance or

clothing damage.

Using a Standpipe to Drain

1 Insert the end of the drain hose into the

standpipe.

2 Use the provided tie strap a to secure the

drain hose in place.

3 If the water valves and drain are built into the

wall, fasten the drain hose to one of the water

hoses with the provided tie strap

b (ribbed

side on inside).

CAUTION

• Do not insert the end of the drain hose into the

standpipe more than 8 inches (20 cm). Doing so

can cause siphoning, odors, or improper

draining.

NOTE

• If the drain is large enough for the flange on the

hose to fit inside, then do not insert the flange

more than 1 - 2 inches into the drain.

Using a Laundry Tub to Drain

1 Hang the end of the drain hose over the side

of the laundry tub.

2 Use the provided tie strap to secure the drain

hose in place.

Leveling the Washer

The tub of the washer spins at very high speeds. To

minimize vibration, noise, and unwanted

movement, the floor must be a solid, level surface.

CAUTION

• Using the washer without leveling it may cause

excess vibration and noise, leading to a washer

malfunction.

• Adjust the leveling feet only as far as necessary

to level the washer. Extending the leveling feet

more than necessary can cause the washer to

vibrate.

NOTE

• Before installing the washer, make sure that the

floor is clean, dry and free of dust, dirt, water

and oil so the washer feet cannot slide easily.

Feet that move or slide on the floor can

contribute to excessive vibration and noise.

29.5 - 96 "

(75 - 244 cm)

29.5 - 96 "

(75 - 244 cm)

14 INSTALLATION

How to Level the Washer

1 Position the washer in its final location.

• Take special care not to pinch, strain, or

crush the water and drain hoses. If you have

a carpenter’s level a, you can use it to

check that the washer is level. The slope

beneath the washer should not exceed 1

inch, and all 4 leveling feet must rest firmly

on the floor.

2 Open the lid and look from above to see if the

tub is centered.

• If the tub is not centered, readjust the front

feet. If you have a level, check the washer

with the level.

NOTE

• To check if the washer is level from side to side,

place a level on the back edge of the lid.

• To check if the washer is level from front to back,

place a level on the edge where the cabinet side

meets the top cover. Do not place the level on

the top of the lid. Using these surfaces will result

in the washer being unlevel.

3 Adjust the leveling feet.

• Turn all 4 leveling feet in one direction to

raise the washer or the other direction to

lower it.

4 Recheck the washer’s levelness.

• Push or rock the top edges of the washer

gently to make sure the washer does not

rock. If the washer rocks,readjust the

leveling feet.

• If the lid does not stay open properly,

extend the front leveling legs until the

washer is level from front to back.

Final Installation Check

Connecting to the Power Supply

Plug the washer into a 120 VAC, 60 Hz grounded 3-

prong outlet.

WARNING

• Do not use a worn or damaged power cord or

power plug. Replace or repair it immediately.

Failure to do so may result in death, fire, electric

shock, or malfunction.

• Do not modify the power cord and plug provided

with the appliance. Do not damage it when

installing or moving the appliance. Doing so may

result in death, fire, electric shock, or

malfunction.

• Make sure that the appliance is grounded.

1″

15INSTALLATION

ENGLISH

• Connect this appliance to a grounded outlet

conforming to the rating prior to use. Failure to

do so may result in fire, electric shock, or

malfunction.

• Do not damage or cut off the ground prong of

the power cord. Doing so may cause death, fire,

electric shock, or product malfunction.

• Improper connection of the equipment-

grounding conductor can result in risk of electric

shock. Check with a qualified electrician or

service technician if you are in doubt as to

whether the appliance is properly grounded. If it

does not fit the outlet, have a proper outlet

installed by a qualified electrician.

• The appliance and outlet must be positioned so

that the plug is easily accessible.

• Do not use adapter or extension cords. Doing so

may result in serious injury, fire, electric shock,

or death.

• For best performance, plug the appliance into its

own individual outlet. This helps prevent

overloading house wiring circuits which could

cause a fire hazard from overheated wires.

• If necessary, use a new, UL-listed 3-prong

(grounding) plug rated at no less than the

branch circuit. Do not use an extension cord

longer than 3 feet. Failure to follow these

warnings may result in serious injury, fire,

electric shock, or death.

Testing the Washer

Check if the washer is properly installed and run a

test cycle.

1 Make sure that the tub is empty. Do not load

anything in the tub for this test.

2 Press the Power button.

3 Press and hold the Spin and Soil buttons

simultaneously until an 1N s code appears in

the display.

•

1N is displayed first, and s, sO, or sE is

displayed.

• 1N s : Initial test

•

1N sO : Previous test result was good.

• 1N sE : Previous test ended with an error.

• The indication is different for each model.

4 Press the Start/Pause button.

• The test will run for about 3 minutes.

• The test automatically checks the water

inlet hoses and the drain hose.

5 Check the display for results.

6 At the end of the test cycle, ENd or O will

display. The washer will shut off automatically

after a short delay.

Installation Check Error Codes

Refer to the chart below before calling for service.

Error Code Solution

IE

• Fully open the water faucet.

• Straighten out any kinks in the

inlet hoses and make sure the

hoses are not pinched against

the wall or under the washer.

OE

• Straighten out any kinks in the

drain hose and make sure the

hose is not pinched against the

wall or under the washer.

• Remove and flush out the drain

hose to remove clogs.

• Adjust or repair the drain.

Maximum drain height is 96

inches.

16 OPERATION

OPERATION

Before Use

WARNING

• To reduce the risk of fire, electric shock, or injury

to persons, read the SAFETY INSTRUCTIONS

before operating this appliance.

Operation Overview

1 Sort laundry and load the washer.

• Sort laundry by fabric type, soil level, color

and load size, as needed. Open the lid and

load items into the washer.

• If using single-use detergent packs, or gel

or tablet detergents, place them in the

drum before loading the laundry.

2 Add cleaning products.

• Add the proper amount of HE (High-

Efficiency) detergent to the detergent

dispenser.

• If desired, add bleach or fabric softener to

the appropriate dispensers.

• Do not place liquid or powdered detergent

packs, or gel or tablet detergents in the

dispenser.

3 Turn on the washer.

• Press the Power button to turn on the

washer.

• The lights above the cycle buttons will

illuminate and a chime will sound.

4 Select a cycle.

• Turn the cycle selector knob or press the

cycle buttons repeatedly until the desired

cycle is selected.

• The preset wash temperature, spin speed,

soil level and option settings for the

selected cycle are shown.

•The Normal cycle must be selected in order

to change its default settings.

• Pressing the Start/Pause button without

selecting a cycle immediately starts the

Normal cycle with the default settings.

5 Adjust settings.

• Default settings for the selected cycle can

be changed, if desired, using the cycle

modifier and option buttons.

• Not all modifiers and options are available

on all cycles. A different chime sounds and

the LED does not light up if the selection is

not allowed.

6 Begin cycle.

•Press the Start/Pause button to begin the

cycle. The lid locks, and the washer agitates

briefly without water to measure the weight

of the load.

•If the Start/Pause button is not pressed

within a certain time, the washer shuts off

and all settings are lost.

NOTE

• You must press and hold the Power button

when turning off the appliance. This helps

prevent accidentally turning it off during a cycle.

7 If necessary, add additional items to the tub

while the Add Garment light is on.

• This light turns on at the beginning of the

wash cycle to indicate when it is safe to add

items to the tub.

•Press the Start/Pause button to pause the

cycle and add items to the tub. Press the

Start/Pause button to resume the cycle.

• Adding items after the Add Garment light

turns off may result in poor wash

performance.

8 End of cycle.

• When the cycle is finished, a melody

sounds. Immediately remove the clothing

from the washer to reduce wrinkling.

• If the washer includes lint filters, remember

to check lint filters after every 2 to 3 loads.

17OPERATION

ENGLISH

Sorting Laundry

CAUTION

• The washer can be fully loaded, but the tub

should not be tightly packed with items. The lid

of the washer should close easily.

•Use the Bedding cycle for buoyant or

nonabsorbent items such as pillows or

comforters. Failure to follow this caution can

result in leakage.

• Clothing or articles that are waterproof or water

resistant must be washed in the Waterproof

cycle only. (Examples include water resistant

clothing, mattress covers, outdoor clothes, and

plastic mats.) Using another cycle may result in

personal injury or damage to the washer,

clothes, walls, floor, and surrounding objects

due to abnormal vibration.

Grouping Similar Items

For the best washing results, and to reduce the

possibility of damage to clothing, sort clothing into

loads made up of similar items.

Mixing different fabric types and/or soil levels can

result in poor wash performance, color transfer,

discoloration, fabric damage or linting. Fabrics

should be sorted into groups as described below.

Colors

Sort articles by color. Wash dark clothes separately

from light colors or whites. Mixing dark clothes

with light clothes can result in dye transfer or

discoloration of the lighter clothes.

Soil Level

Wash heavily soiled clothing together. Washing

lightly soiled clothing in the same load with heavily

soiled clothing could result in poor wash

performance for the lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavy or

sturdy fabric types. Washing heavy fabrics with

delicates can result in poor wash performance for

the heavy fabrics and possible damage to the

delicates.

Lint Type

Some fabrics attract and bind lint to them while

others give off lint in the laundry process. Avoid

mixing these lint collectors and lint producers in

the same load. Mixing these fabrics will result in

pilling and linting on the lint collectors. (For

example, lint collector - knit sweater; lint producer

- terry cloth towels.)

How to Sort Laundry

Fabric Care Labels

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to

the manufacturer’s recommendations.

By Colors By Soil By Fabric By Lint

White Heavy Delicates Lint

Producer

Lights Normal Easy Care Lint

Collector

Darks Light Sturdy

Category Label Directions

Washing

Hand wash

Machine wash, Normal

cycle

Perm Press/Wrinkle

Resistant setting (which

has a cool down or cold

spray before the slower

spin)

Gentle/Delicate setting

(slow agitation and/or

reduced wash time)

Do not wash

Do not wring

Water

Temperature

Hot

Warm

Cold/Cool

Bleach

Symbols

Any bleach (when

needed)

Only non-chlorine

bleach (when needed)

Do not bleach

18 OPERATION

Loading the Washer

General Tips

• Check and empty pockets. Paper clips, coins,

matches, etc. can damage clothing and the

washer.

• Close zippers and hooks, and tie drawstrings to

prevent snagging or tangling of clothes.

• Pretreat heavily stained areas for best results.

• Brush off heavy soil, dust, and hair from items

before washing. Excess dirt or sand can abrade

other fabrics and lead to poor wash

performance.

• Combine large and small items in the tub. Load

large items first. Large items should not be more

than half of total load.

• For best results, load dry items only. If washing

very wet items, wring out excess water before

loading, or run a Spin Only cycle to extract

excess water before adding detergent and

starting the desired cycle.

• The washer can be fully loaded, but the tub

should not be tightly packed with items. The lid

of the washer must close easily.

• The washer will not fill or operate with the lid

open.

• Do not overload the tub. Clothes should fit

loosely in the tub under the maximum fill line

a.

Loading clothes over the fill line may result in

damage to clothing and the washer.

- Do not press down on items while stacking

them in the tub.

- Load clothes loosely, and do not overfill the

tub. Clothes need room to circulate in order to

get clean.

Bulky Items

• Do not wash entire pillows or cushions. Remove

pillow or cushion inserts and wash the covers

only.

•Use the Bedding cycle for large or bulky items

such as poly-filled jackets, comforters, pillows,

etc. These items may not be as absorbent as

other laundry items and should be sorted into a

separate wash load for best performance.

• Bulky items should be placed as far down in the

tub as possible for best performance. Always

place buoyant items at the bottom of the tub.

The washer will automatically detect the load

size. Because of the high efficiency wash system,

the water level may not completely cover the

load.

Small Items

• Do not wash a single small item. Add enough

similar items to the load to prevent an out-of-

balance load.

• Wash small, light items in a mesh bag. Small

items can get caught in the impeller at the

bottom of the tub, and brassiere hooks can

damage other items or the tub.

General Tips for Models with an

Agitator

If the appliance uses a tall, vertical spindle in the

drum, follow these instructions when loading the

washer.

• For best performance, load clothes as shown.

3

19OPERATION

ENGLISH

• To reduce tangling, load items loosely in even

piles surrounding the agitator.

• Do not load a single bulky item unless it fills the

drum. Load several small bulky items around the

agitator to balance the load.

• Do not load bulky items such as pet beds that

are too large or stiff to move easily around the

agitator. Impeding the motion of the drum or

agitator could cause damage to the items or the

washer.

Adding Cleaning Products

About Detergent Use

This washer is designed for use with only HE (High-

Efficiency) detergents.

• HE detergents produce fewer suds, dissolve

more efficiently to improve washing and rinsing

performance, and help to keep the interior of

the washer clean. Using detergent that is not HE

may cause oversudsing and unsatisfactory

performance which could result in error codes,

cycle failure, and washer damage.

• Detergents designated as HE-compatible may

not provide optimal results.

• For proper wash performance, always measure

detergent using the measuring device provided

by the detergent manufacturer. For an average

load, use less than half of the recommended

maximum. Use less detergent for soft water,

light soil, or smaller loads.

• Use extra care when measuring 2X and 3X

concentrated detergents because even a small

amount of extra detergent can lead to problems.

• Never use more than the maximum amount of

detergent recommended by the manufacturer.

Using too much detergent can lead to

oversudsing, poor rinsing, detergent buildup in

clothing, and residue buildup that can contribute

to odors in the washer.

• Do not use more than one single-use detergent

pack or detergent tablet in the washer. Using too

much detergent may cause oversudsing and

unsatisfactory performance. Reduce detergent

amount or add an extra rinse if detergent

residue is left on fabrics. To add an extra rinse,

select the Extra Rinse option.

a Maximum fill line

b Average load fill line

c Liquid detergent

d Powdered detergent

Single-Use Detergent Packs / Gel or

Tablet Detergents

Place liquid or powdered detergent packs, or gel

or tablet detergents in the tub before loading

laundry. Do not place these detergents in the

dispenser.

About the Dispensers

The automatic dispenser consists of two

compartments which hold:

• Liquid fabric softener

• Liquid or powdered detergent for main wash

CAUTION

• Do not place or store laundry products, such as

detergent, bleach, or liquid fabric softener, on

top of your washer. These products can damage

the washer’s finish and controls.

20 OPERATION

NOTE

• Follow the manufacturer’s recommendations

when adding cleaning products.

Using the Detergent and Softener

Dispenser Drawer

To add detergent and fabric softener to the

automatic dispenser drawer:

1 Open the dispenser drawer.

2 Load the laundry products into the

appropriate compartments.

a Liquid fabric softener compartment

b Main wash liquid detergent cup

c Insert

d Main wash powdered detergent

compartment

3 Gently close the detergent dispenser drawer

before starting the cycle.

• Slamming the drawer closed may result in

the detergent overflowing into another

compartment or dispensing into the drum

earlier than programmed.

• Be careful not to get a hand caught in the

drawer while closing.

• It is normal for a small amount of water to

remain in the dispenser compartments at

the end of the cycle.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the

main wash cycle. Either powdered or liquid

detergent may be used in this compartment.

• The detergent is added to the load at the

beginning of the cycle. Always use HE (High-

Efficiency) detergent with your washer.

• Do not exceed the maximum fill line. Using too

much detergent can result in detergent buildup

in clothing and the washer.

• Liquid or powdered color-safe bleach may be

added to the main wash compartment with

detergent of the same type. Do not mix liquids

and powders.

• When using liquid detergent, make sure the

liquid detergent cup and insert are in place.

• When using powdered detergent, remove the

insert and liquid detergent cup from the

dispenser. Powdered detergent will not dispense

with the liquid detergent cup and insert in place.

• If you use a detergent that does not dissolve

easily or a detergent with high viscosity, it will

leave a residue and clog the dispenser.

Fabric Softener Compartment

This compartment holds liquid fabric softener,

which is automatically dispensed during the final

rinse cycle.

• Do not exceed the maximum fill line. Using too

much fabric softener may stain clothes.

• Dilute concentrated fabric softeners with warm

water.

• Never pour fabric softener directly onto the load

or into the tub.

Using the Liquid Bleach Dispenser

The bleach dispenser is a separate compartment

at the left front of the tub opening.

WARNING

• Do not mix chlorine bleach with ammonia or

acids such as vinegar or rust/scale remover.

Mixing chemicals like these can produce a lethal

gas, resulting in severe injury or death.

NOTE

• Do not add powdered bleach to this dispenser.

The bleach dispenser is designed to dispense

liquid bleach only. Powdered or liquid color-safe

bleach will not dispense properly.

• Do not place laundry items on top of the bleach

dispenser when loading and unloading the

washer.

• Never add more than one cup of bleach and do

not exceed the maximum fill line since this can

La page est en cours de chargement...

LG WT7305CW Le manuel du propriétaire

LG WT7305CW Le manuel du propriétaire

dans d''autres langues